Add do_disable_clocks() to disable clock domains and module clocks.
These clocks are enabled using do_enable_clocks().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add do_disable_clocks() to disable clock domains and module clocks.
These clocks are enabled using do_enable_clocks().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add missing registers in struct definition.
Update GPIO MUX base register to match GPIO base (refer to "LPC32x0 User manual" Rev. 3 - 22 July 2011).
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Move arch/arm/cpu/armv7/exynos/* to arch/arm/mach-exynos/* to allow
reuse of existing code for ARMv8 based Exynos platforms.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add support for the mipi pll, this is necessary for getting higher dotclocks
with lcd panels.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The tv-encoder on sun5i is slightly different compared to the one on
sun4i/sun7i.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This header file uses type definitions (u8, u32) from linux/types.h but
doesn't include it. If includes aren't carefully ordered this can cause
build failures.
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add defines to allow reading recovery mode (RCM) boot type from the boot
information table (BIT) written by the boot ROM (BR) to the IRAM.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The "method" parameter was part of the original port of the driver from
the kernel. At some point this may have been added to allow for future
differentiation (as omap1 and omap2 have different GPIO IP blocks, so
this wasn't an unreasonable thing to do). At this point however it's
just extra overhead, so drop.
Signed-off-by: Tom Rini <trini@konsulko.com>
AM43XX SoCs support up to 192 GPIO signals.
Make this amount available to the driver.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
This patch adds the glue code for hi6220 SoC which has 2x synopsis
dw_mmc controllers. This will be used by the hikey board support
in subsequent patches.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds the header files which will be used in the subsquent
board / drivers to enable support for hi6220 hikey board.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
gpio.h - Added missing copyright in few files.
rsa-mod-exp.h - Corrected copyright in the file.
fsl_sec.h - Added missing license in files
drivers/crypto/fsl/Makefile - Removed the incomplete GPLv2 license and replaced it with GPLv2+ license
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reboot mode is written in scratchpad memory before reboot in the form of a
single char, that is the first letter of the reboot mode string as passed to the
reboot function.
This mechanism is supported on OMAP3 both my the upstream kernel and by various
TI kernels.
It is up to each board to make use of this mechanism or not.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
The change adds support of LPC32xx SLC NAND controller.
LPC32xx SoC has two different mutually exclusive NAND controllers to
communicate with single and multiple layer chips.
This simple driver allows to specify NAND chip timings and defines
custom read_buf()/write_buf() operations, because access to 8-bit data
register must be 32-bit aligned.
Support of hardware ECC calculation is not implemented (data
correction is always done by software), since it requires a working
DMA engine.
The driver can be included to an SPL image.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Enable BCM SF2 ethernet and PHY for BCM Cygnus SoC
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
add support for the at91sam9260 based board smartweb from
siemens. SPL is used without serial support, as this
SoC has only 4k sram for running SPL. Here a U-Boot
bootlog:
RomBOOT
>
U-Boot 2015.07-rc2-00109-g4ae828c (Jun 15 2015 - 09:31:16 +0200)
CPU: AT91SAM9260
Crystal frequency: 18.432 MHz
CPU clock : 198.656 MHz
Master clock : 99.328 MHz
Watchdog enabled
DRAM: 64 MiB
WARNING: Caches not enabled
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: macb0
Hit any key to stop autoboot: 0
U-Boot>
Signed-off-by: Heiko Schocher <hs@denx.de>
Add a few extra sunxi display registers and constant defines.
Also rename some existing defines (e.g. dropping _GCTRL) and make
some more generic (e.g. dropping the 2x scaling from
SUNXI_LCDC_TCON1_TIMING_V_TOTAL).
This is a preparation patch for adding composite video out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
USB devices are not really designed to get the power bounced off and on
at them. Esp. USB powered harddisks do not like this.
Currently we power off the USB ports both on a "usb reset" and when
booting the kernel, causing the usb-power to bounce off and then back
on again.
This patch removes the powering off calls, fixing the undesirable power
bouncing.
Note this requires some special handling for the OTG port:
1) We must skip the external vbus check if we've already enabled our own
vbus to avoid false positives
2) If on an usb reset we no longer detect that the id-pin is grounded, turn
off vbus as that means an external vbus may be present now
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
To enable NAND flash in sunxi SPL,
pins 0-6, 8-22 and 24 on port C are configured.
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
T124/210 requires some specific configuration (VPR setup) to
be performed by the bootloader before the GPU can be used.
For this reason, the GPU node in the device tree is disabled
by default. This patch enables the node if U-boot has performed
VPR configuration.
Boards enabled by this patch are T124's Jetson TK1 and Venice2
and T210's P2571.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
U-boot is responsible for enabling the GPU DT node after all necessary
configuration (VPR setup for T124) is performed. In order to be able to
check whether this configuration has been performed right before booting
the kernel, make it happen during board_init().
Also move VPR configuration into the more generic gpu.c file, which will
also host other GPU-related functions, and let boards specify
individually whether they need VPR setup or not.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Added PLL variables (dividers mask/shift, lock enable/detect, etc.)
to new pllinfo struct for each Soc/PLL. PLLA/C/D/E/M/P/U/X.
Used pllinfo struct in all clock functions, validated on T210.
Should be equivalent to prior code on T124/114/30/20. Thanks
to Marcel Ziswiler for corrections to the T20/T30 values.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Added 38.4MHz/48MHz entries to pll_x_table for CPU PLL. Needs
to be measured - should be close to 700MHz (1.4G/2).
Note that some freqs aren't in the PLLU table in T210 TRM
(13, 26MHz), so I used the 12MHz table entry for them. They
shouldn't be selected since they're not viable T210 OSC freqs.
Since there are now 2 new OSC defines, all tables (pll_x_table,
PLLU) had to increase by two entries, but since 38.4/48MHz are
not viable osc freqs on T20/30/114, etc, they're just set to 0.
Signed-off-by: Tom Warren <twarren@nvidia.com>
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Define base address of both usb xhci controllers in lsch3 config
in the format (IMMR + offset) for LS2085A
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Define CONFIG_SYS_CACHELINE_SIZE for LS2085A which is required by
USB XHCI stack for alignment
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. Define two structures mx6ul_iomux_ddr_regs and mx6ul_iomux_grp_regs.
2. Add a new function mx6ul_dram_iocfg to configure dram io.
3. Refactor MMDC1 macro, discard "#ifdef CONFIG_MX6SX". Since
only mmdc0 channel exists on i.MX6SX/UL, redefine MMDC1 macro support
runtime check, but not hardcoding #ifdef macros.
4. Introduce mx6ul-ddr.h, which includes the register address for DRAM
IO configuration.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1. Add enet, uart, i2c, ipg clock support for i.MX6UL.
2. Correct get_periph_clk, it should account for
MXC_CCM_CBCDR_PERIPH_CLK2_PODF_MASK.
3. Refactor get_mmdc_ch0_clk to make all i.MX6 share one function,
but not use 'ifdef'.
4. Use CONFIG_FSL_QSPI for enable_qspi_clk, but not #ifdef CONFIG_MX6SX.
5. Use CONFIG_PCIE_IMX for pcie clock settings, use CONFIG_CMD_SATA for
sata clock settings. In this way, we not need "#if defined(CONFIG_MX6Q)
|| defined....", only need one CONFIG_PCIE_IMX in header file.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Since i.MX6UL's cache line size is 64bytes, need to
define the macro CONFIG_SYS_CACHELINE_SIZE to 64 for i.MX6UL.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
1. Update imx register base address for i.MX6UL.
2. Remove duplicated MXS_APBH/GPMI/BCH_BASE.
3. Remove #ifdef for register addresses that equal to
"AIPS2_OFF_BASE_ADDR + 0x34000" for different chips.
4. According fuse map, complete fuse_bank4_regs.
5. Move AIPS3_ARB_BASE_ADDR and AIPS3_ARB_END_ADDR out of #ifdef CONFIG_MX6SX,
because we can use runtime check
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Add i.MX6UL pins IOMUX file which defines the IOMUX settings for choose.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Add MXC_CPU_MX6UL for i.MX6UL CPU type which is got at runtime from
DIGPROG register. But the value has been occupied by MXC_CPU_MX6D which
is not real id from DIGPROG register, so change i.MX6D to value 0x67 which
was not occupied.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Since i.MX6QP changes some CCM registers, so modify the clocks settings to
follow the hardware changes.
In c files, use runtime check and discard #ifdef.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add cpu type for i.MX6QP/DP.
This patch also fix is_mx6dqp(), since get_cpu_rev can return MXC_CPU_MX6QP
and MXC_CPU_MX6DP, we should use:
(is_cpu_type(MXC_CPU_MX6QP) || is_cpu_type(MXC_CPU_MX6DP)).
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Added routine mmu_set_region_dcache_behaviour() to set a
particular region as non cacheable.
Define dummy routine for mmu_set_region_dcache_behaviour()
to handle incase of dcache off.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Derived from Tegra124, modified as appropriate during T210
board bringup. Cleaned up debug statements to conserve
string space, too. This also adds misc 64-bit changes
from Thierry Reding/Stephen Warren.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
All based off of Tegra124. As a Tegra210 board is brought
up, these may change a bit to match the HW more closely,
but probably 90% of this is identical to T124.
Note that since T210 is a 64-bit build, it has no SPL
component, and hence no cpu.c for Tegra210.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Read device unique ID and set environment variable "serial#".
Value would then be passed to kernel through DTB.
To read ID from DTB, kernel is required to have commit:
3f599875e5202986b350618a617527ab441bf206 (ARM: 8355/1: arch: Show
the serial number from devicetree in cpuinfo)
This commit is already mainline since v4.1-rc1.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Albert Aribaud <albert.u.boot@aribaud.net>
To: Tom Rini <trini@konsulko.com>
To: Kamil Lulko <rev13@wp.pl>
Cc: u-boot@lists.denx.de
This introduces code to read the value of the SYS_BOOT pins on the OMAP3, as
well as the memory-preferred scheme for the interpretation of each value.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
OMAP devices might boot from peripheral devices, such as UART or USB.
When that happens, the U-Boot SPL tries to boot the next stage (complete U-Boot)
from that peripheral device, but in most cases, this is not a valid boot device.
This introduces a fallback option that reads the SYS_BOOT pins, that are used by
the bootrom to determine which device to boot from. It is intended for the
SYS_BOOT value to be interpreted in the memory-preferred scheme, so that the
U-Boot SPL can load the next stage from a valid location.
Practically, this options allows loading the U-Boot SPL through USB and have it
load the next stage according to the memory device selected by SYS_BOOT instead
of stalling.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This cleans up the SPL boot devices for omap platforms and introduces support
for missing boot devices.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces OMAP3 support for the common omap boot code, as well as a
major cleanup of the common omap boot code.
First, the omap_boot_parameters structure becomes platform-specific, since its
definition differs a bit across omap platforms. The offsets are removed as well
since it is U-Boot's coding style to use structures for mapping such kind of
data (in the sense that it is similar to registers). It is correct to assume
that romcode structure encoding is the same as U-Boot, given the description
of these structures in the TRMs.
The original address provided by the bootrom is passed to the U-Boot binary
instead of a duplicate of the structure stored in global data. This allows to
have only the relevant (boot device and mode) information stored in global data.
It is also expected that the address where the bootrom stores that information
is not overridden by the U-Boot SPL or U-Boot.
The save_omap_boot_params is expected to handle all special cases where the data
provided by the bootrom cannot be used as-is, so that spl_boot_device and
spl_boot_mode only return the data from global data.
All of this is only relevant when the U-Boot SPL is used. In cases it is not,
save_boot_params should fallback to its weak (or board-specific) definition.
save_omap_boot_params should not be called in that context either.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Move the musb config and platdata to the sunxi-musb glue, which is where
it really belongs. This is preparation patch for adding device-model
support for the sunxi-musb-host code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for reading the id pin value of the otg connector to the usb
phy code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch extracts checking for valid SD card "eGON.BT0" signature from
`board_mmc_init` into function `sunxi_mmc_has_egon_boot_signature`.
Buffer for mmc sector is allocated and freed at runtime. `panic` is
triggered on malloc failure.
Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Small bugfix to make it work for devs other then mmc0]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add the required files for the Broadcom UDC OTG interface.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Move USB controller Base address mapping from ls102xa immap
to fsl xhci header. This is required to remove any warnings when
controller base addresses are mapped for multiple platforms
in their respective files.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
For ARMv8, outer shareable is 0b10, inner shareable is 0b11 at bit
position [13:12] of TCR_ELx register.
Signed-off-by: Zhichun Hua <zhichun.hua@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
DSPI has pin muxing with SDHC and other IPs, this patch check the
value of RCW SPI_PCS_BASE and SPI_BASE_BASE fields, it also check
the "hwconfig" variable. If those pins are configured to DSPI and
"hwconfig" enable DSPI, set the BRDCFG5 of QIXIS FPGA to configure
the routing to on-board SPI memory. Otherwise will configure to SDHC.
DSPI is enabled in "hwconfig" by appending "dspi", eg.
setenv hwconfig "$hwconfig;dspi"
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As SCFG_ENDIANCR register is added to choose little-endian or big-endian
for audio IPs on Rev2.0 silion, little-endian mode is selected.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
timer_wait is moved from sunxi/psci_sun7i.S, and it can be converted
completely into a reusable armv7 generic timer. LS1021A will use it
as well.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds the infrastructure to update device
tree nodes to convey SMMU stream IDs in the device
tree. Fixups are implemented for PCI controllers
initially.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Stream IDs on ls2085a devices are not hardwired and are
programmed by sw. There are a limited number of stream IDs
available, and the partitioning of them is scenario dependent.
This header defines the partitioning between legacy, PCI,
and DPAA2 devices.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds support to print out the SoC personality.
Freescale LS20xx SoCs (compliant to Chassis-3 specifications) can
have 6 personalities: LS2045AE, LS2045A, LS2080AE, LS2080A,
LS2085AE and LS2085A
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support in mxc_i2c driver, iomux_v3 and vf610 architecture for the four
I2C instances available in VF610.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
hab_status command returns a memory dump of the hab event log. But the
raw data is not human-readable. Parsing such data into readable event
will help to minimize debbuging time.
Signed-off-by: Ulises Cardenas <Ulises.Cardenas@freescale.com>
Add I2C4 clock support for i.MX6SX. Since we use runtime check,
but not macro, we need to remove `#ifdef ..` in crm_regs.h, or
gcc will fail to compile the code succesfully.
Making the macros only for i.MX6SX open to other i.MX6x maybe not
a good choice, but we have runtime check.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
enable_spi_clock does the same thing with enable_cspi_clock, so
remove enable_cspi_clock.
Remove enable_cspi_clock prototype in header file
convert cm_fx6/spl.c to use enable_spi_clk
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The root cause of this problem should now be fixed.
This reverts commit a6a4c542d3.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Pavel Machek <pavel@denx.de>
Tested-by: Pavel Machek <pavel@denx.de>
The A33 adds a pinmux function for UART0 in the PB pin group.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
stv0991 has cadence qspi controller for flash interfacing, this
patch configures the device pads & clock for the controller.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
This reverts commit f76eba38b3.
This patch did not have a full and proper copyright/S-o-b chain.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Conflicts:
include/configs/sun6i.h
include/configs/sun8i.h
Add a new revision CHIP_REV_2_0.
Introudce macro is_mx6dqp, dqp means Dual/Quad Plus.
Since Dual/Quad Plus use same cpu type with Dual/Quad, but different
revision(Major Lower), we use this macro for Dual/Quad Plus.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
is_soc_rev should return a bool value, so use "==", but not "-",
change (is_soc_rev(CHIP_REV_1_0) > 0) to (soc_rev() > CHIP_REV_1_0).
This patch also add space between "&" for cpu_type(rev) macro.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
The recent changes for hw leveling on am33xx were not intended for
DDR2 boards, only DDR3. Update emif_sdram_type to take a sdram_config
value to check against. This lets us pass in the value we would use to
configure, when we have not yet configured the board yet. In other cases
update the call to be as functional as before and check an already
programmed value in.
Tested-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
On AM57xx evm I2C5 is used to detect the LCD board by reading the
EEPROM present on the bus.
Enable i2c5 clocks to help that.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now all manual mode configurations are done as part of
IO delay recalibration sequence, remove the hack done for
CPSW.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In addition to the regular mux configuration, certain pins of DRA7
require to have "manual mode" also programmed, when predefined
delay characteristics cannot be used for the interface.
struct iodelay_cfg_entry is introduced for populating
manual mode IO timings.
For configuring manual mode, along with the normal pad
configuration do the following steps:
- Select MODESELECT field of each assocaited PAD.
CTRL_CORE_PAD_XXX[8]:MODESELECT = 1(Enable MANUAL_MODE macro along with mux)
- Populate A_DELAY, G_DELAY values that are specified in DATA MANUAL.
And pass the offset of the CFG_XXX register in iodelay_cfg_entry.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
On DRA7, in addition to the regular muxing of pins, an additional
hardware module called IODelay which is also expected to be
configured. This "IODelay" module has it's own register space that is
independent of the control module.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay recalibration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do muxing as part of IOdelay recalibration.
IODELAY recalibration sequence:
- Complete AVS voltage change on VDD_CORE_L
- Unlock IODLAY config registers.
- Perform IO delay calibration with predefined values.
- Isolate all the IOs
- Update the delay mechanism for each IO with new calibrated values.
- Configure PAD configuration registers
- De-isolate all the IOs.
- Relock IODELAY config registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
In addition to the regular mux configuration, certain pins of DRA7
require to have "virtual mode" also programmed.
This allows for predefined delay characteristics to be used by the SoC
to meet timing characterstics needed for the interface.
Provide easy to use macro to do the same.
For configuring virtual mode, along with normal pad configuration add
the following two steps:
- Select MODESELECT field of each assocaited PAD.
CTRL_CORE_PAD_XXX[8]:MODESELECT = 1
- DELAYMODE filed should be configured with value given in DATA Manual.
CTRL_CORE_PAD_XXX[7:4]:DELAYMODE =[0-15] (as given in DATA manual).
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Adopting the pinctrl register definitions from Linux kernel
to be consistent.
Old definitions will be removed once all the pinctrl data
is adapted to new definitions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
do_set_mux32() is redefined in dra7xx and beagle_x15 boards.
IO delay recalibration sequence also needs this.
Making it generic to avoid duplication.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
A generic is_dra72x cpu check is useful for grouping
all the revisions under that. This is used in the
subsequent patches.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
DRA7 EMIF supports Full leveling for DDR3.
Adding support for the Full leveling sequence.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a hook to allows boards to add their own init to board_init().
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is required in order to avoid instability when running from caches
after the kernel starts.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
mx5 is a cortex-a8 which has 64 byte cache lines. i'll need this for
adding gadget support to usbarmory, but it's a property common the the
entire SoC family - may as well make it available to all MX5 boards
Works on usbarmory; compile-tested on mx53loco and mx51_efikamx too
Signed-off-by: Chris Kuethe <chris.kuethe@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Matthew Starr <mstarr@hedonline.com>
Cc: Andrej Rosano <andrej@inversepath.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Chris Kuethe <chris.kuethe@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
After that change it would be possible to call samsung_get_base_usb3_phy()
function to get proper base address
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Add IOMUX for the pad used as USB pen. This needs to be driven low for
the Iris and Viola boards where it is pulled up high by default. This is
required for the USB host functionality to work on these boards. Use the
board specific weak initialisation function, to drive the pin low which
would be called on "usb start".
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Inorder to use the pins as GPIO, apart from setting the alt-function,
pinmuxing need to be done, this patch adds pinmux entries of
few GPIOs.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
This commit adds support to the sunxi SPL to load u-boot from the internal
NAND. Note this only adds support to access the boot partitions to load
u-boot, full NAND support to load the kernel, etc. from the nand data
partition will come later.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Make sure definitions for NAND clock and DMA gate bits are the same
across boards.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add initial sun9i (A80) support, only uart + mmc are supported for now.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We should not hardcode MXS_DMA_ALIGNMENT to 32, since we can not guarantee
that socs' cache line size is 32 bytes.
If on chips whose cache line size is 64 bytes, error occurs:
"
NAND: ERROR: v7_dcache_inval_range - start address is not aligned - 0xbdf1d1a0
ERROR: v7_dcache_inval_range - stop address is not aligned - 0xbdf1f4a0
ERROR: v7_dcache_inval_range - start address is not aligned - 0xbdf1d1a0
"
Align MXS_DMA_ALIGNMENT with ARCH_DMA_MINALIGN whose value is same to
CONFIG_SYS_CACHELINE_SIZE if CONFIG_SYS_CACHELINE_SIZE defined.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
ccsr_ddr structure is already defined in fsl_immap.h. Remove
this duplicated define. Move fixed timing into ls1021atwr.h.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
We've never tested the lvds panel support on sun6i+ SoCs until now, and
unsurprisingly the lvds code needed some fixes to work on my ga10h A33
tablet with lvds panel. This makes the panel on that tablet actually work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Make DRAM_ODT_EN Kconfig setting a bool, add a separate DRAM_ODT_CORRECTION
setting for A23 SoCs and use DRAM_ODT_EN Kconfig everywhere instead of
only in dram_sun4i.c and hardcoding odt_en elsewhere.
Note this commit makes no functional changes for existing boards,
its purpose is to allow changing the odt_en value on future A33 boards.
For sun4i/sun5i/sun7i boards which set DRAM_ODT_EN=y (which no defconfigs
currently do) this patch turns on odt for both the DQ and the DQS lines,
whereas previously it was possibly (but not desirable) to turn odt on only
for one of them by setting the in DRAM_ODT_EN option to 1 or 2 instead of 3.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Add support for UART2 (2-pin version but note that RTS/CTS pins are available
pn that port for possible future use), can be selected in config
by using CONFIG_CONS_INDEX=3
Signed-off-by: Laurent Itti <laurentitti@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The MX6 has a temperature grade defined by OCOTP_MEM0[7:6] which is at 0x480
in the Fusemap Description Table in the reference manual. Return this value
as well as min/max temperature based on the value.
Note that the IMX6SDLRM and the IMX6SXRM do not indicate this in the
their Fusemap Description Table however Freescale has confirmed that these
eFUSE bits match the description within the IMX6DQRM and that they will
be added to the next revision of the respective reference manuals.
This has been tested with IMX6 Automative and Industrial parts.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The IMX6 has four different speed grades determined by eFUSE SPEED_GRADING
indicated by OCOTP_CFG3[17:16] which is at 0x440 in the Fusemap Description
Table. Return this frequency so that it can be used elsewhere.
Note that the IMX6SDLRM and the IMX6SXRM do not indicate this in the
their Fusemap Description Table however Freescale has confirmed that these
eFUSE bits match the description within the IMX6DQRM and that they will
be added to the next revision of the respective reference manuals.
These have been tested with IMX6 Quad/Solo/Dual-light 800Mhz and 1GHz grades.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable IOMUX_CONFIG_SION for all I2C pin mux settings, otherwise
we will get erros when doing i2c operations.
error log like the following:
"
wait_for_sr_state: failed sr=81 cr=a0 state=2020
i2c_init_transfer: failed for chip 0xb retry=1
"
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Having bit 22 cleared in the PL310 Auxiliary Control register (shared
attribute override enable) has the side effect of transforming Normal
Shared Non-cacheable reads into Cacheable no-allocate reads.
Coherent DMA buffers in Linux always have a Cacheable alias via the
kernel linear mapping and the processor can speculatively load cache
lines into the PL310 controller. With bit 22 cleared, Non-cacheable
reads would unexpectedly hit such cache lines leading to buffer
corruption.
This was inspired by a patch from Catalin Marinas [1] and also from recent
discussions in the linux-arm-kernel list [2] where Russell King and Rob Herring
suggested that bootloaders should initialize the cache.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2010-November/031810.html
[2] https://lkml.org/lkml/2015/2/20/199
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
1. Introduce a new structure `struct mxc_i2c_bus`, this structure will
used for non-DM and DM.
2. Remove `struct mxc_i2c_regs` structure, but use register offset to access
registers based on `base` entry of `struct mxc_i2c_bus`.
3. Remove most `#ifdef I2C_QUIRK_REG`. Using driver_data to contain platform
flags. A new flag is introduced, I2C_QUIRK_FLAG.
4. Most functions use `struct mxc_i2c_bus` as one of the parameters.
Make most functions common to DM and non-DM, try to avoid duplicated code.
5. Support DM, but pinctrl is not included. Pinmux setting is still set
by setup_i2c, but we do not need bus_i2c_init for DM.
6. struct i2c_parms and struct sram_data are removed.
7. Remove bus_i2c_read bus_i2c_write prototype in header file. The frist
paramter of bus_i2c_init is modified to i2c index. Add new prototype
i2c_idle_bus and force_bus_idle. Since bus_i2c_init is not good for
DM I2C and pinctrl is missed, we use a weak function for i2c_idle_bus.
Board file take the responsibility to implement this function, like this:
"
int i2c_idle_bus(struct mxc_i2c_bus *i2c_bus)
{
if (i2c_bus->index == 0)
force_bus_idle(i2c_pads_info0);
else if (i2c_bus->index == 1)
force_bus_idle(i2c_pads_info1);
else
xxxxxx
}
"
8. Introduce a weak function, enable_i2c_clk
9. Tested on an i.MX7 platform. Log info:
=> dm tree
Class Probed Name
----------------------------------------
root [ + ] root_driver
simple_bus [ ] |-- soc
simple_bus [ ] | |-- aips-bus@30000000
simple_bus [ ] | | |-- anatop@30360000
simple_bus [ ] | | `-- snvs@30370000
simple_bus [ ] | |-- aips-bus@30400000
simple_bus [ ] | `-- aips-bus@30800000
i2c [ ] | |-- i2c@30a20000
i2c [ ] | `-- i2c@30a40000
simple_bus [ ] `-- regulators
=> i2c dev 0
Setting bus to 0
=> i2c probe
Valid chip addresses: 08 50
=> i2c md 8 31
0031: 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
These GPIO_PORTx macros should be in gpio.h, but not in imx-regs.h.
Also, imx-regs.h and iomux-v3.h has same macro defintion for
GPIO_PORTx, and both of them are included in mxc_i2c.c(include
mxc_i2c.h). This will incur build warnings with macro redefinition.
Since iomux-v3.h is not compatible with mx27, we can not simply
include iomux-v3.h for mx27, so move the GPIO_PORTx to gpio.h to
fix the build warning.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
It is convenient for some boards to implement save_boot_params() in C rather
than assembler. Provide a way to return in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adds support for the OHCI companion controller, which makes
usb-1 devices directly plugged into to usb root port work.
Note for now this switches usb-keyboard support for sunxi back from int-queue
support to the old interrupt polling method. Adding int-queue support to the
ohci code and switching back to int-queue support is in the works.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Make sure to enable the SMMU when booting the kernel in non-secure mode.
This is necessary because some of the SMMU registers are restricted to
TrustZone-secured requestors, hence the kernel wouldn't be able to turn
the SMMU on. At the same time, enable translation for all memory clients
for the same reasons. The kernel will still be able to control SMMU IOVA
translation using the per-SWGROUP enable bits.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
These registers can be used to prevent non-secure world from accessing a
megabyte aligned region of RAM, use them to protect the u-boot secure monitor
code.
At first I tried to do this from s_init(), however this inexplicably causes
u-boot's networking (e.g. DHCP) to fail, while networking under Linux was fine.
So instead I have added a new weak arch function protect_secure_section()
called from relocate_secure_section() and reserved the region there. This is
better overall since it defers the reservation until after the sec vs. non-sec
decision (which can be influenced by an envvar) has been made when booting the
os.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
[Jan: tiny style adjustment]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is based on Thierry Reding's work and uses Ian Campell's
preparatory patches. It comes with full support for CPU_ON/OFF PSCI
services. The algorithm used in this version for turning CPUs on and
off was proposed by Peter De Schrijver and Thierry Reding in
http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/210881. It
consists of first enabling CPU1..3 via the PMC, just to powergate them
again with the help of the Flow Controller. Once the Flow Controller is
in place, we can leave the PMC alone while processing CPU_ON and CPU_OFF
PSCI requests.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra boards will have to initialize power management for the PSCI
support this way.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Will be used for unpowergating CPUs.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In this case the secure code lives in RAM, and hence the memory node in
the device tree needs to be adjusted. This avoids that the OS will map
and possibly access the reservation.
Add support for setting CONFIG_ARMV7_SECURE_RESERVE_SIZE to carve out
such a region. We only support cutting off memory from the beginning or
the end of a RAM bank as we do not want to increase their number (which
would happen if punching a hole) for simplicity reasons
This will be used in a subsequent patch for Jetson-TK1.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
I will need mc_security_cfg0/1 in a future patch and I added the rest while
debugging, so thought I might as well commit them.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Warren <twarren@nvidia.com>
CONFIG_ARMV7_VIRT depends on CONFIG_ARMV7_NONSEC, thus doesn't need to
be taken into account additionally. CONFIG_ARMV7_PSCI is only set on
boards that support CONFIG_ARMV7_NONSEC, and it only works on those.
CC: Tang Yuantian <Yuantian.Tang@freescale.com>
CC: York Sun <yorksun@freescale.com>
CC: Steve Rae <srae@broadcom.com>
CC: Andre Przywara <andre.przywara@linaro.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add full link training as a fallback in case the fast link training
fails.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Connect up the clocks and the eDP driver to make these displays work with
Tegra124-based devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add functions to provide access to the display clocks on Tegra124 including
setting the clock rate for an EDP display.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Create a function which sets the source clock for a peripheral, given
the number of mux bits to adjust. This can then be used more generally.
For now, don't export it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
