As DM_ETH is required for all network drivers, it's now safe to remove
the non-DM_ETH support code. Doing this removes some board support code
which was also unused. Finally, this removes some CONFIG symbols that
otherwise needed to be migrated to Kconfig, but were unused in code now.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support of generic IIO channels binding:
./devicetree/bindings/iio/adc/adc.yaml
Keep support of st,adc-channels for backward compatibility.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Split stm32_adc_chan_of_init channel initialization function into
several routines to increase readability and prepare channel
generic binding handling.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
STM32MP13 RCC driver uses Common Clock Framework and also a
'clk-stm32-core' API. Then STM32MPx RCC driver will contain only data
configuration (gates, mux, dividers and the way to check security)
or some specific clocks.
This API will be used by all new other generations of ST Socs.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
We move the existing CONFIG_POST_* functionality over to CFG_POST and
then introduce CONFIG_POST to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Given that we can use Kconfig logic directly to see if we have a program
available on the host or not, change from passing NO_SDL to instead
controlling CONFIG_SANDBOX_SDL in Kconfig directly. Introduce
CONFIG_HOST_HAS_SDL as the way to test for sdl2-config and default
CONFIG_SANDBOX_SDL on if we have that, or not.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At this point all users of this driver enable DM_ETH, so remove the
legacy code paths.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This converts the following to Kconfig:
CONFIG_RTC_DS1337
CONFIG_RTC_DS1337_NOOSC
CONFIG_RTC_DS1338
CONFIG_RTC_DS1374
CONFIG_RTC_DS3231
CONFIG_RTC_MC13XXX
CONFIG_RTC_MXS
CONFIG_RTC_PT7C4338
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_POWER_FSL
CONFIG_POWER_FSL_MC13892
CONFIG_POWER_HI6553
CONFIG_POWER_LTC3676
CONFIG_POWER_PFUZE100
CONFIG_POWER_PFUZE3000
CONFIG_POWER_SPI
CONFIG_POWER_TPS65090_EC
CONFIG_POWER_TPS65218
CONFIG_POWER_TPS65910
Signed-off-by: Tom Rini <trini@konsulko.com>
As we have more legacy PMIC drivers to move to Kconfig, guard them all
with POWER_LEGACY or SPL_POWER_LEGACY. Do the same kind of check for
building the drivers too. This also means that we need to resort the
list slightly in the Makefile.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_PCI and
CONFIG_SYS_PCIE namespace do not easily transition to Kconfig. In many
cases they likely should come from the device tree instead. Move these
out of CONFIG namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These RTC drivers are currently unused and reference other unused CONFIG
variables, so remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NUM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NS16550
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SPL_NS16550_MIN_FUNCTIONS
CONFIG_SYS_NS16550_MEM32
CONFIG_SYS_NS16550_PORT_MAPPED
CONFIG_SYS_NS16550_REG_SIZE
CONFIG_SYS_NS16550_SERIAL
To do this we also introduce CONFIG_SPL_SYS_NS16550_SERIAL so that
platforms can enable the legacy driver here for SPL.
Signed-off-by: Tom Rini <trini@konsulko.com>
This symbol is specific to the PowerPC SPL implementation, so rename
this to reflect that it's in SPL and used / tested there, so that we can
then safely migrate it to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NAND
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_PAGE_2K
CONFIG_SYS_NAND_PAGE_4K
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_MAX_OOBFREE
CONFIG_SYS_NAND_MAX_ECCPOS
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is the only driver, and only one platform makes use of, setting
CONFIG_SYS_NAND_ECC_BASE. Reference ATMEL_BASE_ECC directly in this
case.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_HW_ECC
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_HW_ECC_OOBFIRST
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_DBW_8
CONFIG_SYS_NAND_DBW_16
Note that all instances of the code check for CONFIG_SYS_NAND_DBW_16
being defined, and then "else" to CONFIG_SYS_NAND_DBW_8 whereas all of
the configs set CONFIG_SYS_NAND_DBW_8. So we introduce
CONFIG_SYS_NAND_DBW_16 as an option.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Consider unexpected values for frequency:
* negative frequency
* zero frequency
* frequency exceeding sampling frequency
As in these cases the sum of the samples is zero also check the count of
the samples.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
'sound play 1 100000' results in an endless loop on the sandbox.
If the frequency exceeds half the sampling rate, zero out the output
buffer.
Fixes: 511ed5fdd3 ("SOUND: SAMSUNG: Add I2S driver")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
xilinx:
- Fix MAC address selection for System Controller from FRU
- Cleanup Kconfig (ZYNQ_MAC_IN_EEPROM symbol)
versal:
- Create u-boot.elf for mini spi configurations
versal-net:
- Enable MT35XU flash
zynq:
- Add missing timer to DT for mini configurations
zynqmp:
- Do not include psu_init to U-Boot by default
- Do not enable IPI by default to mini U-Boot
- Update Luca's fragment
- Fix SPL_FS_LOAD_PAYLOAD_NAME usage
spi:
- gqspi: Fix tapdelay values
- gqspi: Fix 64bit address support
- cadence: Remove condition for calling enable linear mode
- nor-core: Invert logic to reflect sst26 flash unlocked
net:
- Add PCS/PMA phy support
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCY422rQAKCRDKSWXLKUoM
ITrXAJ9sVsVNwnjS99ZdNg64zx/Y5mSRlgCdGMho9/PT6BRmOV4IygwOsEGy7I8=
=XsS5
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.01-rc3-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2023.01-rc3-v2
xilinx:
- Fix MAC address selection for System Controller from FRU
- Cleanup Kconfig (ZYNQ_MAC_IN_EEPROM symbol)
versal:
- Create u-boot.elf for mini spi configurations
versal-net:
- Enable MT35XU flash
zynq:
- Add missing timer to DT for mini configurations
zynqmp:
- Do not include psu_init to U-Boot by default
- Do not enable IPI by default to mini U-Boot
- Update Luca's fragment
- Fix SPL_FS_LOAD_PAYLOAD_NAME usage
spi:
- gqspi: Fix tapdelay values
- gqspi: Fix 64bit address support
- cadence: Remove condition for calling enable linear mode
- nor-core: Invert logic to reflect sst26 flash unlocked
net:
- Add PCS/PMA phy support
flash_is_locked is changed to flash_is_unlocked with commit 513c6071ce
("mtd: spi: Convert is_locked callback to is_unlocked"). sst26_is_locked()
is also changed to sst26_is_unlocked() but the logic remained same.
Invert the logic for the flash lock/unlock to work properly.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20221122051833.13306-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
cadence_qspi_apb_enable_linear_mode() has a weak function defined, so no
need to gaurd this under if (CONFIG_IS_ENABLED(ARCH_VERSAL)).
In cadence_qspi_apb_write_execute(), enable linear mode is called twice by
mistake, remove extra one.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221129114134.18909-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When we pass the 64-bit address to read/write, only lower 32-bit
address is getting updated. Program the upper 32-bit address in the
DMA destination memory address MSBs register, which can handle upto
44-bit destination address.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221125104413.26140-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The driver was using an incorrect value for GQSPI_LPBK_DLY_ADJ_DLY_1
tapdelay for Versal for frequencies above 100MHz. Change it from 2 to 1
based on the recommended value in IP spec.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20221123090451.11409-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Both PCS/PMA PHY and the external PHY need to have a valid link status
in order to have Ethernet traffic. Check and wait this status at
setup_phy() so that we could diagnose if there is a PHY issue.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Link: https://lore.kernel.org/r/20221101035800.912644-3-andy.chiu@sifive.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
If we bridge an external PHY to Xilinx's PCS/PMA PHY and would like to
get and set the real status of the PHY facing the external world. Then
we should phy_connect() to the external PHY instead of the PCS/PMA one.
Thus, we add a pcs-handle DT entry, which have been merged in Linux, and
leave the configuration of it to the driver itself.
Unlike Linux, where the PCS/PMA PHY is managed by phylink, managing the
PCS/PMA PHY is only internal to the driver in U-Boot. The PCS/PMA PHY
pressents only when the phy-mode is configured as SGMII or 1000Base-X,
so it is always 1 Gbps and full-duplex and we may skip passing link
information out.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Link: https://lore.kernel.org/r/20221101035800.912644-2-andy.chiu@sifive.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The TI sysc bus driver is required to allow access to the SPI bus on
am335x platforms. To support SPI boot this driver needs to be enabled in
the SPL/TPL as appropriate.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
We should only perform additional iteration steps when needed to
initialize the parent of a device. Other binding errors (such as a
missing driver) should not lead to additional iteration steps.
Unnecessary iteration steps can cause issues when memory is tightly
constrained (such as in the TPL/SPL) since device_bind_by_name()
unconditionally allocates memory for a struct udevice. On the SanCloud
BBE this led to boot failure caused by memory exhaustion in the SPL
when booting from SPI flash.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Add a driver for the Intel XWAY GbE PHY:
- configure RGMII using dt phy-mode and standard delay properties
- use genphy_config
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The rx descriptor list is in cached memory, and there may be multiple
descriptors per cache-line. After reclaim_rx_buffers marks a descriptor
as unused it does a cache flush, which causes the entire cache-line to
be written to memory, which may override other descriptors in the same
cache-line that the controller may have written to.
The fix skips freeing descriptors that are not the last in a cache-line,
and if the freed descriptor is the last one in a cache-line, it marks
all the descriptors in the cache-line as unused.
This is similarly to what is done in drivers/net/fec_mxc.c
In my case this bug caused tftpboot to fail some times when other
packets are sent to u-boot in addition to the ongoing tftp (e.g. ping).
The driver would stop receiving new packets because it is waiting
on a descriptor that is marked unused, when in reality the descriptor
contains a new unprocessed packet but while freeing the previous buffer
descriptor & flushing the cache, the driver accidentally marked the
descriptor as unused.
Signed-off-by: Yaron Micher <yaronm@hailo.ai>
Fix a couple of typos:
- s/Acquantia/Aquantia/
- s/firmare/firmware/
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add new desc_per_cacheline property which lets a platform run RX descriptor
cleanup after every power-of-2 - 1 received packets instead of every packet.
This is useful on platforms where (axi_bus_width EQOS_AXI_WIDTH_n * DMA DSL
inter-descriptor word skip count + DMA descriptor size) is less than cache
line size, which necessitates packing multiple DMA descriptors into single
cache line.
In case of TX descriptors, this is not a problem, since the driver always
does synchronous TX, i.e. the TX descriptor is always written, flushed and
polled for completion in eqos_send().
In case of RX descriptors, it is necessary to update their status in bulk,
i.e. after the entire cache line worth of RX descriptors has been used up
to receive data.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Separate TX and RX DMA rings to make their handling slightly clearer.
This is a preparatory patch for bulk RX descriptor flushing.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
LiteX is a soft system-on-chip that targets FPGAs. LiteETH is a basic
network device that is commonly used in LiteX designs.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Drop support for quickly deprecated DT property "snps,ref-clock-period-ns"
to prevent its proliferation.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
GUCTL.REFCLKPER can only account for clock frequencies with integer
periods. To address this, program REFCLK_FLADJ with the relative error
caused by period truncation. The formula given in the register reference
has been rearranged to allow calculation based on rate (instead of
period), and to allow for fixed-point arithmetic.
Additionally, calculate a value for 240MHZDECR. This configures a
simulated 240Mhz clock using a counter with one fractional bit (PLS1).
This register is programmed only for versions >= 2.50a, since this is
the check also used by commit db2be4e9e30c ("usb: dwc3: Add frame length
adjustment quirk").
[ marek: Ported from Linux kernel commit
596c87856e08d ("usb: dwc3: Program GFLADJ") ]
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Marek Vasut <marex@denx.de> # Port from Linux
Instead of using a special property to determine the reference clock
period, use the rate of the reference clock. When we have a legacy
snps,ref-clock-period-ns property and no reference clock, use it
instead. Fractional clocks are not currently supported, and will be
dealt with in the next commit.
[ marek: Ported from Linux kernel commit
5114c3ee24875 ("usb: dwc3: Calculate REFCLKPER based on reference clock") ]
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Marek Vasut <marex@denx.de> # Port from Linux
Set reference clock period when it differs from dwc3 default hardware
set.
We could calculate clock period based on reference clock frequency. But
this information is not always available. This is the case of PCI bus
attached USB host. For that reason we use a custom property.
Tested (USB2 only) on IPQ6010 SoC based board with 24 MHz reference
clock while hardware default is 19.2 MHz.
[ baruch: rewrite commit message; drop GFLADJ code; remove 'quirk-' from
property name; mention tested hardware ]
[ marek: Ported from Linux kernel commit
7bee318838890 ("usb: dwc3: reference clock period configuration") ]
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Balaji Prakash J <bjagadee@codeaurora.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Marek Vasut <marex@denx.de> # Port from Linux
Cache ref_clk clock pointer in struct dwc3 . This is a preparatory
patch for subsequent backports from Linux kernel which configure
GFLADJ register content based on the ref_clk rate and therefore need
access to the ref_clk pointer.
It is possible to extract the clock pointer from existing clk_bulk
list of already claimed clock, no need to call clk_get*() again.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The "generic_bus_%x_dev_%x" string which is printed into this buffer
can be up to 34 characters long ("generic_bus_12345678_dev_12345678").
The buffer would be clipped by snprintf() if both %x were at maximum
range. Make sure the buffer is long enough to cover such possibility.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use macro to represent the RL and WL setting to ensure the PHY and
controller setting are aligned.
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Adjust the following settings to get better timing and signal quality.
1. write DQS/DQ delay
- 1e6e2304[0]
- 1e6e2304[15:8]
2. read DQS/DQ delay
- 0x1e6e0298[0]
- 0x1e6e0298[15:8]
3. CLK/CA timing
- 0x1e6e01a8[31]
4. Read and write termination
- change RTT_ROM from 40 ohm to 48 ohm (MR1[10:8])
- change RTT_PARK from disable to 48 ohm (MR5[8:6])
- change RTT_WR from 120 ohm to disable (MR2[11:9])
- change PHY ODT from 40 ohm to 80 ohm (0x1e6e0130[10:8])
Note1: Both DDR-PHY and DDR controller have their own registers for DDR4
Mode Registers (MR0~MR6). This patch introduces macros to synchronize
the MR value on both sides.
Note2: the waveform meansurement can be found in item #21 of Aspeed
AST26x0 Application note (AP note).
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
The condition "~data" in the if-statement is a typo. The original
intention is to poll if SDRAM_PHYCTRL0_INIT bit equals to 0. So use
"data == 0" for instead.
Besides, the bit[1] of "phy_status" register is hardwired to
SDRAM_PHYCTRL0_INIT (with inverse logic). Since SDRAM_PHYCTRL0_INIT has
already done, remove the unnecessary checking of phy_status[1].
Fixes: fde9314346 ("ram: aspeed: Add AST2600 DRAM control support")
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
- Re-add the old PHY reset binding for nanopi-k2
-----BEGIN PGP SIGNATURE-----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=yEaP
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20221122' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Implement setbrg op to meson serial device
- Re-add the old PHY reset binding for nanopi-k2
Invoking lseek() may result in an error. Handle it.
Addresses-Coverity-ID: 376212 ("Error handling issues (CHECKED_RETURN)")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Implement setbrg in amlogic/meson serial device with driver model
similar to how the meson_uart.c driver does it in Linux. Also
configure (probe) the serial device with the new reg5 register.
Signed-off-by: Edoardo Tomelleri <e.tomell@gmail.com>
Link: https://lore.kernel.org/r/20220918161701.572814-1-e.tomell@gmail.com
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
When cadence_qspi_versal_flash_reset() function is called in mini
u-boot where there is no firmware support, it is missing defines for
macro's BOOT_MODE_POR_0 & BOOT_MODE_POR_1. Remove them and replace with
already define macro's which have same values as these.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add soc_xilinx_versal_net driver to identify the family & revision of
versal-net SoC. Add Kconfig option CONFIG_SOC_XILINX_VERSAL_NET to
enable/disable this driver. To enable this driver by default, add this
config to xilinx_versal_net_virt_defconfig file. This driver will be
probed using platdata U_BOOT_DEVICE structure which is specified in
mach-versal-net/cpu.c.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/613d6bcffd9070f62cf348079ed16c120f8fc56f.1668612993.git.michal.simek@amd.com
Use dot instead of comma. The fix doesn't affect anything but it is good to
be aligned with used pattern. The first is used only for string size
calculation and the second change is in the comment.
Fixes: db681d4929 ("net: phy: Add new read ethernet phy id function")
Signed-off-by: Michal Simek <michal.simek@amd.com>
Current xilinx_timer_get_count() implementation does not take into account
the periodic 32-bit wrap arounds, as it directly returns the 32-bit counter
register value. The roll-overs cause problems in the upper timer layers, as
generic timer code expects an incrementing 64-bit value from get_count() to
work correctly.
Add the missing 64-bit up-conversion to fix random hangs/delays in
__udelay().
Fixes: a36d86720f ("microblaze: Convert axi timer to DM driver")
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221012053656.1492457-3-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Relocate timer_ops pointers when CONFIG_NEEDS_MANUAL_RELOC is enabled.
The (gd->flags & GD_FLG_RELOC) check was added to make sure the reloc_done
logic works for drivers that use DM_FLAG_PRE_RELOC.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20221012053656.1492457-2-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Align timer uclass with the other subsystems and provide a timer_get_ops()
convenience macro.
Using this instead of the generic device_get_ops() also prevents
-Wdiscarded-qualifiers warnings when used with non-const variables.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20221012053656.1492457-1-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Removing the zynq_board_read_rom_ethaddr() function as
xlnx,eeprom is not used anymore. As all board dts to use
nvmem alias instead of xlnx,eeprom.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221017094818.17996-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Since commit c2fd0ca1a8
("watchdog: Integrate watchdog triggering into the cyclic framework")
GD_FLG_WDT_READY has become write-only. This patch now removes this
flag completely.
The vacant spot in gd_flags is filled with the newly introduced
GD_FLG_CYCLIC_RUNNING flag.
Suggested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Stefan Roese <sr@denx.de>
Checking for DM_RESET is not enough since not all watchdog
implementations use a reset lane. Such is the case for Rockchip
implementation for example. Since reset_assert_bulk will only succeed if
the resets property exists in the watchdog DT node, it needs to be
called only if a reset property is present.
This adds a condition on the resets property presence in the watchdog DT
node before assuming a reset lane needs to be fetched with
reset_assert_bulk, by calling ofnode_read_prop.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
DFU implementation does not bound the length field in USB
DFU download setup packets, and it does not verify that
the transfer direction. Fixing the length and transfer
direction.
CVE-2022-2347
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Sync the critical clocks in the U-Boot driver with those marked as
critical in Linux. The Linux driver has an explanation of why each clock
is considered to be critical, so import that too.
Fixes: 2f27c9219e ("clk: Add Microchip PolarFire SoC clock driver")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Not all "periph" clocks are children of the AHB clock, some have the AXI
clock as their parent & the mtimer clock is derived from the external
reference clock directly. Stop assuming the AHB clock to be the parent
of all "periph" clocks and define their correct parents instead.
Fixes: 2f27c9219e ("clk: Add Microchip PolarFire SoC clock driver")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Tested-by: Padmarao Begari <padmarao.begari@microchip.com>
The original devicetrees for PolarFire SoC messed up & defined the
msspll's output as a fixed-frequency, 600 MHz clock & used that as the
input for the clock controller node. The msspll is not a fixed
frequency clock and later devicetrees handled this properly. Check the
devicetree & if it is one of the fixed ones, register the msspll.
Otherwise, skip registering it & pass the reference clock directly to
the cfg clock registration function so that existing devicetrees are
not broken by this change.
As the MSS PLL is not a "cfg" or a "periph" clock, add a new driver for
it, based on the one in Linux.
Fixes: 2f27c9219e ("clk: Add Microchip PolarFire SoC clock driver")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Tested-by: Padmarao Begari <padmarao.begari@microchip.com>
Currently the clock driver for PolarFire SoC takes a very naive approach
to the relationship between clocks. It reads the dt to get an input
clock, assumes that that is fixed frequency, reads the "clock-frequency"
property & uses that to set up both the "cfg" and "periph" clocks.
Simplifying for the sake of incremental fixes, the "correct" parentage for
the clocks currently supported in U-Boot is that the "cfg" clocks should
be children of the fixed frequency clock in the dt. The AHB clock is one
of these "cfg" clocks and is the parent of the "periph" clocks.
Instead of passing the clock rate of the fixed-frequency clock to the
"cfg" and "periph" registration functions and the name of the parents,
pass their actual parents & use clk_get_rate() to determine their parents
rates.
The "periph" clocks are purely gate clocks and should not be reading the
AHB clocks registers to determine their rates, as they can simply report
the output of clk_get_rate() on their parent.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Add newline at the end of the printed string.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
A late ack is currently being sent at the end of a transfer due to
incorrect logic in mchp_corei2c_empty_rx(). Currently the Assert Ack
bit is being written to the controller's control reg after the last
byte has been received, causing it to sent another byte with the ack.
Instead, the AA flag should be written to the control register when
the penultimate byte is read so it is sent out for the last byte.
Reported-by: Andreas Buerkler <andreas.buerkler@enclustra.com>
Fixes: 0dc0d1e094 ("i2c: Add Microchip PolarFire SoC I2C driver")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Removed Tag by hs: Fixes: 0190d48488 ("i2c: microchip: fix ack sending logic")
"Master receive mode" was not correctly sending ACKs/NACKs in the
interrupt handler. Bring the handling of M_SLAR_ACK, M_RX_DATA_ACKED &
M_RX_DATA_NACKED in line with the Linux driver.
Fixes: 0dc0d1e094 ("i2c: Add Microchip PolarFire SoC I2C driver")
Reported-by: Shravan Chippa <shravan.chippa@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This reverts commit c7878a0483.
Since commit c7878a0483 ("serial: mxc: have putc use the TXFIFO"),
serial console corruption can be seen when priting inside board_init().
Revert it to avoid the regression.
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These files reference SZ_ macros without including <linux/sizes.h>,
correct this.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_MMC_MAX_BLK_COUNT
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This converts the following to Kconfig:
CONFIG_SYS_MAX_NAND_DEVICE
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_INTERLAKEN
CONFIG_SYS_ISA_IO
CONFIG_SYS_ISA_IO_BASE_ADDRESS
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_I2C_INIT_BOARD
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The description claims that the device is probed but it isn't.
Add the device_probe() call.
Also consolidate the iteration into one function.
Fixes: 8a5cbc065d ("dm: blk: Use uclass_find_first/next_device() in blk_first/next_device()")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Update the sandbox implementation to use UCLASS_HOST and adjust all
the pieces to continue to work:
- Update the 'host' command to use the new API
- Replace various uses of UCLASS_ROOT with UCLASS_HOST
- Disable test_eficonfig since it doesn't work (this should have a unit
test to allow this to be debugged)
- Update the blk test to use the new API
- Drop the old header file
Unfortunately it does not seem to be possible to split this change up
further.
Signed-off-by: Simon Glass <sjg@chromium.org>
Create a block driver for the new HOST uclass. This handles attaching and
detaching host files.
For now the uclass is not used but this will be plumbed in with future
patches.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sandbox supports block devices which can access files on the host machine.
At present there is no uclass for this. The devices are attached to the
root devic. The block-device type is therefore set to UCLASS_ROOT which
is confusing.
Block devices should be attached to a 'media' device instead, something
which handles access to the actual media and provides the block driver
for the block device.
Create a new uclass to handle this. It supports two operations, to attach
and detach a file on the host machine.
For now this is not fully plumbed in.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function now finds its block-device child by looking for a child
device of the correct uclass (UCLASS_BLK). It cannot produce a device of
any other type, so drop the superfluous check.
Provide a version which does not probe the device, since that is often
needed when setting up the device's platdata.
Also fix up the function's comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some tests access data in block devices and so cause the cache to fill
up. This results in memory being allocated.
Some tests check the malloc usage at the beginning and then again at the
end, to ensure there is no memory leak caused by the test. The block cache
makes this difficult, since the any test may cause entries to be allocated
or even freed, if the cache becomes full.
It is simpler to clear the block cache after each test. This ensures that
it will not introduce noise in tests which check malloc usage.
Add the logic to clear the cache, using the existing blkcache_invalidate()
function. Drop the duplicate code at the same time.
Signed-off-by: Simon Glass <sjg@chromium.org>
The support added later in this series tweaks the PMIC voltages in the
SPL. Enable support for the rn5t567 in SPL builds to allow this to be done
cleanly.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for the rn5t568 PMIC to the rn5t567 driver.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Jaehoon Chung <j80.chung@samsung.com>
If the bd718x7 is required, but PMIC_CHILDREN is disabled, this
driver throws a compile error. Fix this by putting the function
to bind children into an if-statement checking for PMIC_CHILDREN.
Allowing PMIC_CHILDREN to be disabled in SPL saves some space and
still permits some read/write functions to access the PMIC in
early startup.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Unlike the other 64-bit mvebu SoCs the AlleyCat5 uses the older ehci
block from the 32-bit SoCs. Adapt the ehci-marvell.c driver to cope with
the fact that the ac5 does not have the mbus infrastructure the 32-bit
SoCs have and ensure USB_EHCI_IS_TDI is selected.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for the AlleyCat5 SoC. This lacks the mbus from the other
users of the mvneta.c driver so a new compatible string is needed to
allow for a different window configuration.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The struct is only used to overlay the MMIO region, so the behavior is
the same. This obsoletes the Kconfig option for the number of ports.
Signed-off-by: Samuel Holland <samuel@sholland.org>
As PLICSW is used to trigger the software interrupt, we should rename
Andes PLIC configuration and file name to reflect the usage. This patch
also updates PLMT and PLICSW compatible strings to be consistent with
OpenSBI fdt driver.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The "Arm Ltd. Dual-Timer Module (SP804)" is a simple 32-bit count-down
timer IP with interrupt functionality, and is used in some SoCs from
various vendors.
Add a simple DM compliant timer driver, to allow users of the SP804 to
switch to DM_TIMER.
This relies on the input clock to be accessible via the DM clock
framework, which should be fine as we probably look at fixed-clock's
here anyway.
We re-program the control register in the probe() function, but keep
the divider in place, in case this has been set to something on purpose
before.
The TRM for the timer IP can be found here:
https://developer.arm.com/documentation/ddi0271/latest
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The FWU Multi Bank Update feature supports updating firmware images
to one of multiple sets(also called banks) of images. The firmware
images are clubbed together in banks, with the system booting images
from the active bank. Information on the images such as which bank
they belong to is stored as part of the metadata structure, which is
stored on the same storage media as the firmware images on a dedicated
partition.
At the time of update, the metadata is read to identify the bank to
which the images need to be flashed(update bank). On a successful
update, the metadata is modified to set the updated bank as active
bank to subsequently boot from.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
In the FWU Multi Bank Update feature, the information about the
updatable images is stored as part of the metadata, on a separate
partition. Add a driver for reading from and writing to the metadata
when the updatable images and the metadata are stored on a block
device which is formatted with GPT based partition scheme.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
In the FWU Multi Bank Update feature, the information about the
updatable images is stored as part of the metadata, which is stored on
a dedicated partition. Add the metadata structure, and a driver model
uclass which provides functions to access the metadata. These are
generic API's, and implementations can be added based on parameters
like how the metadata partition is accessed and what type of storage
device houses the metadata.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
When MMC_WRITE is disabled this driver produced a build error. Fix this.
Also update a comment while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Use the correct SPL_TPL_ variable so that these features can be enabled in
TPL and VPL as needed.
Disable it by default in TPL to avoid any code-size increase. No boards
are actually using it since the Makefile rules don't allow including
drivers/block/ with TPL_DM enabled. It can be manually enabled as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add test coverage for blk_write() as well.
The blk_erase() is not tested for now as the USB stor interface does not
support erase.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we have functions called blk_dread(), etc., which take a
struct blk_desc * to refer to the block device. Add some functions which
use udevice instead, since this is more in keeping with how driver model
is supposed to work.
Update one of the tests to use this.
Note that it would be nice to update the functions in disk-uclass.c to use
these new functions. However they are not quite the same. For example,
disk_blk_read() adds the partition offset to 'start' when calling the
cache read/fill functions, but does not with part_blk_read(), which does
the addition itself. So as designed the code is duplicated.
Signed-off-by: Simon Glass <sjg@chromium.org>
STI timer is actually ARM Cortex A9 global timer. Convert the driver to
use generic global timer name and make it consistent with Linux kernel
global timer driver. This also allows any A9 based device to use this
driver.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
As CONFIG_ARCH_BCM6753 is replaced with CONFIG_BCM6855, update the
driver Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
As CONFIG_ARCH_BCM6858 is replaced with CONFIG_BCM6858, update the
driver Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
As CONFIG_ARCH_BCM68360 is replaced with CONFIG_BCM6856, update the
driver Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
As CONFIG_ARCH_BCM63158 is replaced with CONFIG_BCM63158, update the
Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCY17nfA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXPPoAJ0UYyt3kwslUlAJhOC+KU9UlYnVuwCbBXIQyBua
K5clq+GyxXfaDl2Hnvc=
=XXVp
-----END PGP SIGNATURE-----
Merge tag 'video-20221030' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix [hv]sync active vs back porch in dw_mipi_dsi
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
This option should not have the SYS_ in it. Drop it so it fits in with the
other video options.
Also simplify the alignment code in gunzip_bmp(), since malloc() always
returns a 32-bit-aligned pointer.
Signed-off-by: Simon Glass <sjg@chromium.org>
The bmp command already has a way to centre the image. Using this CONFIG
option to also centre it makes it impossible to control where images are
placed on the screen. Drop the extra check.
Simplify the Kconfig file we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not as simple as it seems. Add a function to provide it so that
the upcoming menu feature can space lines out correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new 'font' command which allows the fonts to be listed as well as
selecting a different font and size.
Allow the test to run on sandbox, where multiple font/size combinations
are supported, as well as sandbox_flattree, where they are not.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to support multiple fonts. Add a function to
handle this as well as one to list the available fonts.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the truetype console supports only a single font and size. It
is useful to be able to support different combinations. As a first step,
move the metrics into there own structure and allow having multiple
metrics.
Signed-off-by: Simon Glass <sjg@chromium.org>
Put this check into a function so we can use it elsewhere. Also drop the
macros which do the same thing but are not actually used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Generalise the video_clear() function to allow filling with a different
colour.
Tidy up the comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is actually a panel, not a video device. Rename the option, move it
into the right place and make it depend on PANEL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move these commands and the implementation to the cmd/ directory, which is
where most commands are kept.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
[agust: keep vidconsole_position_cursor() in vidconsole uclass]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add an exported function which allows the cursor position to be set to
pixel granularity. Make use of this in the existing code.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these are attached to vidconsole which means that the video
uclass requires that a console is enabled. This is not the intention.
The colours are a reasonable way of indexing common colours in any case,
so move them to the video uclass instead.
Rename vid_console_color() to video_index_to_colour() now that it is more
generic. Also fix the inconsistent spelling in these functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
The wrong fields are pulled out of the timings here so the values
programmed into the DSI_VID_HSA_LINES/DSI_VID_HBP_LINES and
DSI_VID_VSA_LINES/DSI_VID_VBP_LINES registers are swapped.
Use the right fields so that the correct values are programmed.
Fixes: d4f7ea83fc ("video: add MIPI DSI host controller bridge")
Signed-off-by: John Keeping <john@metanate.com>
When probing a device fails NULL pointer is returned, and following
devices in uclass list cannot be iterated. Skip to next device on error
instead.
With that the only condition under which these simple iteration
functions return error is when the dm is not initialized at uclass_get
time. This is not all that interesting, change return type to void.
Fixes: 6494d708bf ("dm: Add base driver model support")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
uclass_first_device/uclass_next_device return value will be removed,
don't use it.
With the current implementation dev is equivalent to !ret. It is
redundant to check both, ret check can be replaced with dev check, and
ret check inside the iteration is dead code.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is needed in the platforms that use "ranges" node property for
address translation in their dts for TPL.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The call to device_bind_with_driver_data() passes id->data but if
the entry has no of_match then the id has not been set by the selected
driver.
Normally this passes unnoticed since a previous driver likely had an
of_match value, so the id is set to that. Of course it is not correct
to pass the id->data from a different driver.
With clang-14 the driver ordering is such that the id is never actually
set in the 'bind /usb@1 usb_ether' line in test_bind_unbind_with_node()
thus causing a crash.
Fix this by passing 0 if the of_match for a driver does not exist.
Signed-off-by: Simon Glass <sjg@chromium.org>
Matching anything that just happens to have the sought-for label as a
prefix is wrong. For example, if the board designer has designated 10
lines for debug purposes, named "debug1" through "debug10", and we are
looking up "debug1", if debug10 happens to be met first during the
iteration we'd wrongly return that.
In theory, this can break existing users that could rely on this
quirk, but OTOH keeping the current broken semantics can cause a lot
of grief for people hitting this in the future and not understanding
why they don't find the line they expect. Considering how few in-tree
defconfigs currently set DM_GPIO_LOOKUP_LABEL (ignoring sandbox, only
four "real" boards), let's fix it before the use becomes more
widespread.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add Nuvoton NPCM BMC Peripheral SPI controller driver.
NPCM750 include two general-purpose SPI interface.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The GPMC is a unified memory controller dedicated for interfacing
with external memory devices like
- Asynchronous SRAM-like memories and ASICs
- Asynchronous, synchronous, and page mode burst NOR flash
- NAND flash
- Pseudo-SRAM devices
This driver will take care of setting up the GPMC based on
the settings specified in the Device tree and then
probe its children.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
- nuvoton: add expire function for generic reset (Jim)
- handle watchdogs during keyed autoboot (Rasmus)
- cyclic: Don't disable cylic function upon exceeding CPU time (Stefan)
- ulp wdog: Updates to support iMX93 and DM (Alice)
Avoid concatenation with following message.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
If a regulator does not support .set_suspend_enable or
.set_suspend_value then ret is set to ENOSYS early in the function.
The most serious impact of this is that when no automatic setting of
voltage is needed then the final regulator_set_enable() is skipped
because ret has not been cleared.
It seems that the error handling for regulator_set_suspend_value() is
also wrong as if this succeeds then the normal boot-on checks are still
required, and again ENOSYS needs special treatment here.
Fixes: 11406b8f7e ("dm: regulator: support regulator more state")
Signed-off-by: John Keeping <john@metanate.com>
Commit 290ffe5788 (imx8m: fix reading of DDR4 MR registers) lifted a
private definition of lpddr4_mr_read() from imx8mm-cl-iot-gate board
code to drivers/ddr/imx/imx8m/ddrphy_utils.c, because that version
actually seems to work in practice.
However, commit 99c7cc58e1 (ddr: imx: Add i.MX9 DDR controller driver)
reintroduced the broken version in drivers/ddr/imx/imx8m/ddr_init.c,
copied most of the rest of ddrphy_utils.c to
drivers/ddr/imx/phy/ddrphy_utils.c, and stopped building
drivers/ddr/imx/imx8m/ddrphy_utils.c [and that file was then finally
completely removed with 7e9bd84883 (imx8m: ddrphy_utils: Remove unused
file)].
I assume this must have broken the imx8mm-cl-iot-gate board, at least
those that have not had their eeprom programmed with the proper
information. It certainly did break our out-of-tree board which always
reads back the ID register and uses that for a sanity check.
So apply the fix from 290ffe5788 once again.
Fixes: 99c7cc58e1 (ddr: imx: Add i.MX9 DDR controller driver)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable driver model for ulp watchdog timer. When CONFIG_WDT=y and the
status of device node is "okay", initr_watchdog will be called and
finally calls ulp_wdt_probe() and ulp_wdt_start().
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The reset source of the external PMIC on i.MX93 is WDOG_ANY PAD and the
source of WDOG_ANY PAD is interrupt. Therefore, using PMIC to reset
needs to enable the watchdog interrupt.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The WDOG clocks are sourced from the fixed 32KHz (lpo_clk).When the
timeout period exceeds 2 seconds, the value written to the TOVAL
register is larger than 16-bit can represent. Enabling watchdog
prescaler to solve this problem.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
To use 32bits refresh and unlock command as default, check the CMD32EN
bit to select the corresponding commands.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
In order to test that U-Boot actually maintains the watchdog device(s)
during long-running busy-loops, such as those where we wait for the
user to stop autoboot, we need a watchdog device that actually does
something during those loops; we cannot test that behaviour via the DM
test framework.
So introduce a relatively simple watchdog device which is simply based
on calling the host OS' alarm() function; that has the nice property
that a new call to alarm() simply sets a new deadline, and alarm(0)
cancels any existing alarm. These properties are precisely what we
need to implement start/reset/stop. We install our own handler so that
we get a known message printed if and when the watchdog fires, and by
just invoking that handler directly, we get expire_now for free.
The actual calls to the various OS functions (alarm, signal, raise)
need to be done in os.c, and since the driver code cannot get access
to the values of SIGALRM or SIG_DFL (that would require including a
host header, and that's only os.c which can do that), we cannot simply
do trivial wrappers for signal() and raise(), but instead create
specialized functions just for use by this driver.
Apart from enabling this driver for sandbox{,64}_defconfig, also
enable the wdt command which was useful for hand-testing this new
driver (especially with running u-boot under strace).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
This is a companion to u-boot,noautostart. If one has a single
watchdog device that one does want to have auto-started, but several
others that one doesn't, the only way currently is to set the
CONFIG_WATCHDOG_AUTOSTART and then use the opt-out for the majority.
The main motivation for this is to add an autostarted watchdog device
to the sandbox (to test a fix) without having to set AUTOSTART in
sandbox_defconfig and add the noautostart property to the existing
devices. But it's also nice for symmetry, and the logic in
init_watchdog_dev() becomes simpler to read because we avoid all the
negations.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Correct pointer dereferencing check to be more consistent.
Eliminate the below smatch warning:
drivers/mmc/mmc.c:3118 mmc_init_device()
warn: variable dereferenced before check 'm' (see line 3116)
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Unconditionally clearing DTO when RXDR is set leads to spurious timeouts
in FIFO mode transfers if events occur in the following order:
mask = dwmci_readl(host, DWMCI_RINTSTS);
// Hardware asserts DWMCI_INTMSK_DTO here
dwmci_writel(host, DWMCI_RINTSTS, DWMCI_INTMSK_DTO);
if (mask & DWMCI_INTMSK_DTO) {
// Unreachable as DTO is cleared without being handled!
return 0;
}
Only clear interrupts that we have seen and are handling so that DTO is
not missed.
Signed-off-by: John Keeping <john@metanate.com>
Tested-by: Jerome Forissier <jerome.forissier@linaro.org> (Rock PI 4B)
Tested-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The SDMMC IOs can be in an IO domain, that has to be enabled.
This is done by enabling vqmmc in the driver.
This has no impact on configurations not using an IO domain, the check
can then be executed on all platforms managing regulator, and the vqmmc
regulator enabled on all platforms having it in their DT.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The UHS modes for SD, HS200 and HS400 modes for eMMC are not supported
by the stm32_sdmmc2 driver.
Make it clear by removing the corresponding caps after parsing the DT.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
To support dual data rate with STM32 sdmmc2 driver, the dedicated bit
(DDR - BIT(18)) needs to be set in the CLKRC register. Clock bypass
(no divider) is not allowed in this case. This is required for the
eMMC DDR modes.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add Socionext F_SDH30_E51 IP support. The features of this IP includes
CMD/DAT line delay and force card insertion mode for non-removable cards.
And the IP needs to add some quirks.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
This patch defines a quirk to disable the block count
for single block transactions.
This is similar to Linux kernel commit d3fc5d71ac4d
("mmc: sdhci: add a quirk for single block transactions").
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Get rid of discrepancy beween comment /* 250 ms */ and code
which shifts by 4 thus dividing by 16.
So change code to shift by 2 and make the timeout value 250 ms.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Array index for SCCR 22th DWORD should be 21.
Fixes: bebdc23750 ("mtd: spi-nor: Parse SFDP SCCR Map")
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The flash's internal address mode is tracked by nor->add_mode_nbytes and
it is set to 3 in BFPT parse. SEMPER multi-die package parts (>1Gb) are
3- or 4-byte address mode by default, depending on model number. We need
to make sure that 4-byte address mode is used for multi-die package parts.
For single-die package parts (<=1Gb), registers can be accessed by 3-byte
address. Read, program, and erase use the 4B opcodes that always take
4-byte address regardless of flash's internal address mode.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Read/Write Any Register commands take 3- or 4- byte address depending on
flash's internal address mode. The nor->addr_width tracks number of
address bytes used in read/program/erase ops that can be 4
(with 4B opcodes) regardless of flash's internal address mode. The
nor->addr_mode_nbytes tracks flash's internal address mode so replace
nor->addr_width by that.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The nor->addr_width tracks number of address bytes used in
read/program/erase ops and eventually set to 4 for >16MB chips, regardless
of flash's internal address mode. For Infineon SEMPER flash's, we use
Read/Write Any Register commands for configuration and status check.
These commands take 3- or 4-byte address depending on flash's internal
address mode.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
JESD216D-01 mentions that "defaults to 3-Byte mode; enters 4-Byte mode on
command."
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add flash info table entries for s28hl512gt, s28hl01gt, and s28hs01gt.
These devices have the same functionality as s28hs512t.
In spi-nor-core, use device ID byte to detect S28 family instead of
device name.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Change configuration macro name to support all other devices in SEMPER S28
family.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Change prefix to support all other devices in SEMPER S28 family.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add gpio driver for ADP5585 I/O Expander Controller. The ADP5585 is a 10
input/output port expander and can be used to increase the number of
I/Os available to a processor.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Update the ftgmac100 driver to support NC-SI instead of an mdio phy
where available. This is a common setup for Aspeed AST2x00 platforms.
NC-SI mode is determined from the device-tree if either phy-mode sets it
or the use-ncsi property exists. If set then normal mdio setup is
skipped in favour of the NC-SI phy.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add the handling of NC-SI ethernet frames, and add a check at the start
of net_loop() to configure NC-SI before starting other network commands.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
There are no platforms that have not migrated to using DM_KEYBOARD,
remove the legacy option.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are no longer any platforms which do not enable DM, move this to a
def_bool y and remove the check in the Makefile.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
issue:
CAAM fails with key error when perform Modular Exponentiation
using PKHA Block in CAAM
Fix:
add flush and invalidate dcache for keys, signature
and output decrypted data processed by CAAM.
Fixes: 34276478f7 (DM: crypto/fsl - Add Freescale rsa DM driver)
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The QSPI clocks are only used when CONFIG_NXP_FSPI=y, so only build the
QSPI clocks in this case to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The ecspi clocks are only used when CONFIG_DM_SPI=y, so only build the
ecspi clocks in this case to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Ethernet is not used inside SPL, so move the IMX8MM_CLK_ENET_AXI clock
inside the non-SPL block to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
PWM is not used inside SPL, so do not define the PWM clocks inside
SPL to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Move init_clk_usdhc to non-clk driver case, since assigned-clocks properties
will initialize the clocks by clk driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- dts update and sync for rk356x, rk3288, rk3399 from Linux;
- Add rk3399 EAIDK-610 board support;
- Update for puma-rk3399 board;
- some fix and typo fix in different drivers;
This contains various fixes (some long overdue) for the next release.
-----BEGIN PGP SIGNATURE-----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=H1Iz
-----END PGP SIGNATURE-----
Merge tag 'clk-2023.01' of https://source.denx.de/u-boot/custodians/u-boot-clk
Clock patches for 2023.01
This contains various fixes (some long overdue) for the next release.
Beside some rather unexciting sync of the DTs from the kernel tree, and
some Kconfig cleanup, there are some improvements for the ARMv5 Allwinner
family, to support boards with the F1C200s (64MB DRAM) better. We will
get actual board support as soon as the DTs have passed the Linux review
process.
There is also support for the X96 Mate TV Box, featuring the H616 SoC and
a full 4GB of DRAM.
Also we found the secret to enable SPI booting on the H616 (pin PC5 must
be pulled to GND), so the SPI boot support patch is now good to go.
Passed the gitlab CI, plus briefly tested on Pine64-LTS, LicheePi Nano,
X96 Mate and OrangePi Zero.
The k210 driver is selected by sandbox_defconfig.
Building the sandbox on 32bit systems fails with:
test/dm/k210_pll.c: In function ‘dm_test_k210_pll_calc_config’:
include/linux/bitops.h:11:38: warning:
left shift count >= width of type [-Wshift-count-overflow]
11 | #define BIT(nr) (1UL << (nr))
| ^~
test/dm/k210_pll.c:36:54: note: in expansion of macro ‘BIT’
36 | error = abs((error - BIT(32))) >> 16;
| ^~~
Use the BIT_ULL() macro to create a u64 value.
Replace abs() by abs64() to get correct results on 32bit system
Apply the same for the unit test.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
All functions getting and setting clock rate use ulong for rate, only
clk_get_parent_rate is an exception. Change the return value to match
other clock rate funcrions.
Most users directly assign the rate to unsigned long anyway, and the few
users that use u64 (not s64) multiply the rate so they may need the
extra bits for the result in their use case.
Fixes: 4aa78300a0 ("dm: clk: Define clk_get_parent_rate() for clk operations")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20220928103757.11870-1-msuchanek@suse.de
Some boards with the Allwinner F1C100s family SoCs use UART1 for its
debug UART, so define the pins for the SPL and the pinmux name and mux
value for U-Boot proper.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
RAM_PX30_DDR4 is for DDR4 support and not DDR3 so let's fix the typo.
Fixes: 2db36c64bd ("ram: rockchip: px30: add a config-based ddr selection")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The original code set up the DDR clock to 48 MHz, not 50MHz as
requested, and did it in a way that didn't satisfy the Application
Notes in RK3399 TRM [1]. 2.9.2.B says:
PLL frequency range requirement
[...]
FOUTVCO: 800MHz to 3.2GHz
2.9.2.A :
PLL output frequency configuration
[...]
FOUTVCO = FREF / REFDIV * FBDIV
FOUTPOSTDIV = FOUTVCO / POSTDIV1 / POSTDIV2
FREF = 24 MHz
The original code gives FOUTVCO: 24MHz/1 * 12 = 288MHz < 800MHz
And the resulting FOUTPOSTDIV is 288MHz / 3 / 2 = 48MHz
but the requested frequency was 50MHz
Note:
2.7.2 Detail Register Description
PMUCRU_PPLL_CON0 says
fbdiv
Feedback Divide Value
Valid divider settings are:
[16, 3200] in integer mode
So .fbdiv = 12 wouldn't be right. But 2.9.2.C says:
PLL setting consideration
[...]
The following settings are valid for FBDIV:
DSMPD=1 (Integer Mode):
12,13,14,16-4095 (practical value is limited to 3200, 2400, or 1600
(FVCOMAX / FREFMIN))
[...]
So .fbdiv = 12 would be right.
In any case FOUTVCO is still wrong. I thank YouMin Chen for
confirmation and explanation.
Despite documentation, I don't seem to be able to reproduce a
practical problem with the wrong FOUTVCO. When I initially found it I
thought some problems with detecting the RAM capacity in my Rock Pi 4B
could be related to it and my patch seemed to help. But since I'm no
longer able to reproduce the issue, it works with or without this
patch. And meanwhile a patch[2] by Lee Jones and YouMin Chen addresses
this issue. Btw, shouldn't that be commited?
So this patches solves no visible problem. Yet, to prevent future
problems, I think it'd be best to stick to spec.
An alternative to this patch could be
{.refdiv = 1, .fbdiv = 75, .postdiv1 = 6, .postdiv2 = 6};
This would theoretically consume more power and yield less jitter,
according to 2.9.2.C :
PLL setting consideration
[...]
For lowest power operation, the minimum VCO and FREF frequencies
should be used. For minimum jitter operation, the highest VCO and
FREF frequencies should be used.
[...]
But I haven't tried it because I don't think it matters much. 50MHz
for DDR is only shortly used by TPL at RAM init. Normal operation is
at 800MHz. Maybe it's better to use less power until later when more
complex software can control batteries or charging or whatever ?
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@vrull.eu>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Sean Anderson <seanga2@gmail.com>
Link: [1] https://opensource.rock-chips.com/images/e/ee/Rockchip_RK3399TRM_V1.4_Part1-20170408.pdf
Link: [2] https://patchwork.ozlabs.org/project/uboot/list/?series=305766
Signed-off-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Tested-by: Michal Suchánek <msuchanek@suse.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
All of the required values for using the omap_wdt.c driver are found in
<asm/ti-common/omap_wdt.h> and this is what is indirectly pulled in via
<asm/arch/hardware.h> when it exists.
Signed-off-by: Tom Rini <trini@konsulko.com>
DMA operations should function on DMA addresses, not virtual addresses.
Although these are usually the same in U-Boot, it is more correct
to be explicit with our types here.
Signed-off-by: Andrew Davis <afd@ti.com>
We should clean the caches before any DMA operation and clean+invalidate
after. This matches what the DMA framework does for us already but adds
it to the two functions here in this driver that don't yet go through the
new DMA framework.
Signed-off-by: Andrew Davis <afd@ti.com>
The DMA'd memory area needs cleaned and invalidated after the DMA
write so that any stale cache lines do not mask new data.
Signed-off-by: Andrew Davis <afd@ti.com>
