As M4 is sourcing UART clk from OSC, to make UART work
when M4 is enabled, need to select OSC as clk parent,
24M OSC is enough for debug UART in uboot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
There is not LDO_SOC/PU/ARM/MMDC1 on i.MX6SLL, also no need to gate/ungate
all PFDs to make PFD working.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Under very rare timing circumstances, transitioning into streaming
mode might create a data corruption. Present on Two or more processors
or 1 core with ACP, all revisions. This erratum can be worked round
by setting bit[22] of the undocumented Diagnostic Control Register to 1.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The ARM errata 751472, 794072, 761320 only applied
to the following configuration:
This erratum affects configurations with either:
- One processor if the ACP is present
- Two or more processors
i.MX6 family does not have the ACP and thus only the MPCore system
will be impacted, which are the i.MX6DQ, i.MX6DL, and i.MX6QP.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
The IPU AXI QoS for the i.MX6QP and i.MX6DP processors have to be set as
commented in the code:
/* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */
Set IOMUXC_GPR6 and IOMUXC_GPR7 to 0x77177717 instead of 0x007F007F.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
The IPU AXI QoS for the i.MX6QP and i.MX6DP processors have to be set as
commented in the code:
/* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */
Set IOMUXC_GPR6 and IOMUXC_GPR7 to 0x77177717 instead of 0x007F007F.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Use the env_save() function directly now that there is only one
implementation of saveenv().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is a strange name for a function that loads the environment. There is
now only one implementation of this function, so use the new env_load()
function directly instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
We only have a single implementation of this function now and it is called
env_get_char(). Drop the old function and the weak version.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that env_init() is only defined once we can drop the env_init_new()
name and just use env_init().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This variable is declared as a global in most environment location
drivers. But it is not used outside the drivers and most of the
declarations are unnecessary.
Also some drivers call free() on env_ptr which seems wrong since it is
not in the heap.
Drop the variable where possible, and all calls to free().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a name to the driver and use that instead of the global variable
declared by each driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Most of the init() implementations just use the default environment.
Adjust env_init_new() to do this automatically, and drop the redundant
code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move over to use a the master implementation of the location drivers, with
each method calling out to the appropriate driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
We plan to move to a environment access via drivers for each location
where the environment can be stored. Add an implementation for this. So
far it is not used, but will be pressed into service in a future patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we support multiple environment drivers but there is not way to
select between them at run time. Also settings related to the position and
size of the environment area are global (i.e. apply to all locations).
Until these limitations are removed we cannot really support more than one
environment location. Adjust the location to be a choice so that only one
can be selected. By default the environment is 'nowhere', meaning that the
environment exists only in memory and cannot be saved.
Also expand the help for the 'nowhere' option and move it to the top since
it is the default.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Move all of the imply logic to default X if Y so it works again]
Signed-off-by: Tom Rini <trini@konsulko.com>
Change these board to use a live device tree after relocation.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Fix USB OTG power enable aka USBO1_EN which on Apalis T30 is connected
to the T30 ball GEN2_I2C_SCL.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Set up a location driver for each supported environment location. At
present this just points to the global functions and is not used. A
later patch will switch this over to use private functions in each driver.
There are several special cases here in various drivers to handle
peculiarities of certain boards:
1. Some boards define CONFIG_ENV_IS_IN_FAT and CONFIG_SPL_ENV_SUPPORT but
do not actually load the environment in SPL. The env load code was
optimised out before but with the driver, it is not. Therefore a special
case is added to env/fat.c. The correct fix (depending on board testing
might be to disable CONFIG_SPL_ENV_SUPPORT.
2. A similar situations happens with CONFIG_ENV_IS_IN_FLASH. Some boards
do not actually load the environment in SPL, so to reduce code size we
need to drop that code. A similar fix may be possible with these boards,
or it may be possible to adjust the environment CONFIG settings.
Added to the above is that the CONFIG_SPL_ENV_SUPPORT option does not
apply when the environment is in flash.
Obviously the above has been discovered through painful and time-consuming
trial and error. Hopefully board maintainers can take a look and figure
out what is actually needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to use this name for all environment drivers. Update the nand
driver to use a more specific name.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present we have three states for the environment, numbered 0, 1 and 2.
Add an enum to record this to avoid open-coded values.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function is the same as env_get_char_spec() apart from dropping the
brackets. Drop the brackets from env_get_char_spec() and use that instead
of env_get_char_memory().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function does nothing but call env_get_char_spec(). Drop it and
adjust its only caller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The check for gd->env_valid is used in both the 'if' and 'else' part of
env_get_char(). Move it into that function instead for simplicity. Drop
that code from the two leaf functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function is not used anywhere other than env_get_char(). Move the
code into that function.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions are not used outside this file. Make them static and order
them to avoid forward declarations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
About a quarter of the files in common/ relate to the environment. It
seems better to put these into their own subdirectory and remove the
prefix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This target stops us using 'env' as a subdirectory. It is not mentioned in
the help so seems to be an internal target. Rename it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
OLimex A64-OLinuXino is an open-source hardware board
using the Allwinner A64 SOC.
OLimex A64-OLinuXino has
- A64 Quad-core Cortex-A53 64bit
- 1GB or 2GB RAM DDR3L @ 672Mhz
- microSD slot and 4/8/16GB eMMC
- Debug TTL UART
- HDMI
- LCD
- IR receiver
- 5V DC power supply
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
NanoPi A64 is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner A64 SOC.
Nanopi A64 features
- Allwinner A64, 64-bit Quad-core Cortex-A53@648MHz to 1.152GHz, DVFS
- 1GB DDR3 RAM
- MicroSD
- Gigabit Ethernet (RTL8211E)
- Wi-Fi 802.11b/g/n
- IR receiver
- Audio In/Out
- Video In/Out
- Serial Debug Port
- microUSB 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini <trini@konsulko.com>
Even after memory free of phydev, priv is still pointing to the
obsolete address.
So update priv->phydev as NULL after memory free.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for Microchip LAN7500, LAN7800 and LAN7850,
USB to 10/100/1000 Ethernet Controllers.
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add an mii helper function to resolve flow control status per
IEEE 802.3-2005 table 28B-3.
This function was taken from the Linux source tree.
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
While it is likely that this entire case is superfluous and can be
removed, correct the test now to match what is in rockchip-common.h and
makes sense based on context of the code. Otherwise we get a large
number of warnings.
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
A few years ago STM32F1 SoCs support has been added :
0144caf22c gpio: stm32: add stm32f1 support
2d18ef2364 ARMv7M: add STM32F1 support
But neither STM32F1 dedicated defconfig nor board was
associated to these commits.
Got confirmation from Tom Rini and Matt Porter to remove
all this code [1]
[1] http://u-boot.10912.n7.nabble.com/Remove-STM32F1-support-td301603.html
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
