Add mcu cpsw and its components along with scm_conf node
to have ethernet functional.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add new driver for the TI AM65x SoC Gigabit Ethernet Switch subsystem (CPSW
NUSS). It has two ports and provides Ethernet packet communication for the
device and can be configured as an Ethernet switch. CPSW NUSS features: the
Reduced Gigabit Media Independent Interface (RGMII), Reduced Media
Independent Interface (RMII), and the Management Data Input/Output (MDIO)
interface for physical layer device (PHY) management. The TI AM65x SoC has
integrated two-port Gigabit Ethernet Switch subsystem into device MCU
domain named MCU_CPSW0. One Ethernet port (port 1) with selectable RGMII
and RMII interfaces and an internal Communications Port Programming
Interface (CPPI) port (Host port 0).
Host Port 0 CPPI Packet Streaming Interface interface supports 8 TX
channels and on RX channels operating by TI am654 NAVSS Unified DMA
Peripheral Root Complex (UDMA-P) controller.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use phys_addr_t for mdio_base address to avoid build
warnings on arm64 and dra7. Cast it to uintprt_t before
assigning to regs.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch is to use block layer to read from mmc in cortina
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Because all MSCC SoC use the same MDIO bus, put the implementation in
one common file(mscc_miim) and make all the other MSCC network drivers to
use these functions.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
A very simple test for DM_MDIO, mimicks a register write/read through the
sandbox bus to a dummy PHY.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
stand-alone devices. Useful in particular for systems that support
DM_ETH and have a stand-alone MDIO hardware block shared by multiple
Ethernet interfaces.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When serdes configuration was written in hardware there was a delay
of 100ms to be sure that configuration was written. But the delay is not
needed because already the function serdes_write it is checking that the
operation finished.
Therefore remove the mdelay. This improves the speed of configuring the
network driver.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The code block reading the DT property for the clock output control was
before the phy's DT node pointer was set, so it could never work. Move
it after the node pointer is set.
Also store the unsigned 32-bit property into an unsigned value, not a
signed value, as the former will cause a problem if value overflows.
For instance, if one were to add 0xffffffff as a code to mean the clock
output should be turned off.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Janine Hagemann <j.hagemann@phytec.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When not using DM_ETH, these PHY settings are programmed with default
values hardcoded into the driver. When using DM_ETH, they should come
from the device tree. However, if the device tree does not have the
properties, the driver will silent use -1. Which is entirely out of
range, programs nonsense into the PHY's registers, and does not work.
Change this to use the same defaults as non-DM_ETH if the device tree is
lacking the properties.
As an alternative, the kernel driver for the phy will display an error
message and fail if the device tree is lacking.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Janine Hagemann <j.hagemann@phytec.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
These are standard across gigabit phys. These mostly extend the
auto-negotiation information with gigabit fields.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Share the code that prints out a register field with the function that
prints out the "special" fields.
There were two arrays the register dump list, one with reg number and
name, another with a pointer to the field table and the table size.
These two arrays had have each entry match what register is referred to.
Combine them into just one table. Now they can't not match and there is
just one table.
Add some missing consts to pointers to string literals.
The dump code was ignoring the regno field in the description table and
assuming register 0 was at index 0, etc. Have it use the field.
Change reg > max+1 into reg >= max, which doesn't fail if max+1 could
overflow, besides just making more sense.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- mmc spi driver model support
- drop mmc_spi command
- enhanced Strobe mmc HS400 support
- minor mmc bug/fixes and optimization
- omap hsmmc and mvbeu update
- sdhci card detect support
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.
Linux commit details about the sun8i-h3-beelink-x2.dts sync:
"ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2"
(sha1: cc4bddade114b696ab27c1a77cfc7040151306da)
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The choice of the SPL_TEXT_BASE is not really a decision that should be
specified by each board's defconfig, as this setting is actually
dictated by the SoC's memory map and the BootROM behaviour.
To make this obvious and reduce the clutter in the defconfig files,
let's specify the SoC constraints in the Kconfig stanza.
This allows us to remove these lines from the defconfig files again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Flash system partition with fastboot will earse the partition firstly
The 600ms timeout will fail on some SD Card. Enlarge it to 5s to make
it works for most of sdcard
Cc: guoyin.chen <guoyin.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement set_enhanced_strobe hook for fsl_esdhc_imx,
,in esdhc_set_timing and esdhc_change_pinstate, also handle HS400_ES.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
eMMC 5.1+ supports HS400 Enhances Strobe mode without the need for
tuning procedure.
The flow is as following:
- set HS_TIMIMG (Highspeed)
- Host change freq to <= 52Mhz
- set the bus width to Enhanced strobe and DDR8Bit(CMD6),
EXT_CSD[183] = 0x86 instead of 0x80
- set HS_TIMING to 0x3 (HS400)
- Host change freq to <= 200Mhz
- Host select HS400 enhanced strobe complete
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Should use CONFIG_IS_ENABLED not IS_ENABLED for clock and regulator drivers,
CONFIG_IS_ENABLED will check the CONFIG_SPL_CLK and CONFIG_SPL_DM_REGULATOR
when building SPL.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The mmc_spi command was added to manually setup MMC over SPI bus
using command. This was required by the legacy non-DM MMC_SPI driver.
With DM based MMC_SPI driver in-place, we can now use all general
storge commands and mmc command for MMC over SPI bus hence we remove
the mmc_spi command all it's references.
Suggested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch rewrites MMC SPI driver using U-Boot DM
framework and get it's working on SiFive Unleashed
board.
Signed-off-by: Bhargav Shah <bhargavshah1988@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The MMC mode and width are fixed for MMC SPI host hence we skip
sd_select_mode_and_width() and mmc_select_mode_and_width() for
MMC SPI host.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Accessing the boot partition had been error prone with HS200 and HS400 and
was disabled. The driver first switched to a lesser mode and then switched
the partition access. It was mostly due to a bad handling of the switch and
has been fixed, so let's remove this 'feature'
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The switch operation can sometimes make the bus unreliable, in that case
the send_status parameter should be false to indicate not to poll using
CMD13. If polling on dat0 is possible, we should use it to detect the end
of the operation.
At the end of the operation it is safe to use CMD13 to get the status of
the card. It is important to do so because the operation may have failed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The e-MMC spec allows the e-MMC to specify a timeout for the partition
switch command. It can take up to 2550 ms. There is no lower limit to this
value in the spec, but do as the the linux driver does and force it to be
at least 300ms.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Starting with rev 4.5, the eMMC can define a generic timeout for the
SWITCH command.
Following Linux Kernel code, the timeout also changed from 1000 -> 500
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Using the DAT0 line as a rdy/busy line is an alternative to reading the
status register of the card. It especially useful in situation where the
bus is not in a good shape, like when modes are switched.
This is also how the linux driver behaves.
Note of warning: As per the specification, while polling on DAT0 the CLK
must not turned off: "[...] Without a clock edge the Device (unless
previously disconnected by a deselect command (CMD7)) will force the DAT0
line down, forever. [...]"
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
mmc_send_status() is currently used to poll the card until it is ready, not
actually returning the status of the card.
Make it return the status and add another function to poll the card.
Also remove the 'extern' declaration in the mmc-private.h header to comply
with the coding standard.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This reverts commit 318a7a576b.
The last and only user of this callback had been the omap_hsmmc driver.
It is not used anymore. Removing the callback.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This is not required. The MMC core sends CMD0 right after the
initialization and it serves the same purpose.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
It sometimes happen that the PSTATE register does not indicate that the
bus is ready when it really is. This usually happens after a mode switch.
In that case it makes sense to reset the FSM handling the CMD and DATA
Also reset the FSMs if the STATE register cannot be cleared. This also
sometimes happens after a mode switch.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The response type of CMD25 is R1 instead of R1b.
Signed-off-by: Akio Hirayama <hirayama.akio@socionext.com>
[masahiro: add log ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Card detect function implemented for SDHCI framework.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch reads cd-gpio property from devicetree
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This patch reads card detect properties from device tree &
added mmc capability macros in mmc.h.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Removed MMC_CAP_NONREMOVABLE, MMC_CAP_NEEDS_POLL macros from
mvebu_mmc.h to avoid redefining of these macros when compiled with
mvebu based configs.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This test is currently broken so disable it for now.
Cc: Ramon Fried <ramon.fried@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Since we have limited resources in SPL, it is the best interest
to keep the SPL as small as possible and that includes the DTB.
There are a few items in the device tree that can be removed,
because these boards don't use them.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fixed regulators don't have a set_value method. Therefore, trying to
set their value will always return -ENOSYS.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
add gpio-hog support. GPIO hogging is a mechanism
providing automatic GPIO request and configuration
as part of the gpio-controller's driver probe function.
for more infos see:
doc/device-tree-bindings/gpio/gpio.txt
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Michal Simek <michal.simek@xilinx.com> (zcu102)
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
