The early bootup information is not print out due to
the UART pin iomux not set up correctly before board_init
Add the board_early_init_f function and enable the
CONFIG_BOARD_EARLY_INIT_F. Move the UART pin setting
from board_init to board_early_init_f function.
This patch also move the FEC pin iomux setup to the
board_early_init_f.
Signed-off-by: Jason Liu <r64343@freescale.com>
fix saveenv or env save command not work on mx51evk board.
with this patch, we can use savenv or env save to
store enviroments to mmc card slot 0
Signed-off-by: Jason Liu <r64343@freescale.com>
This patch is to fix build breakage and support new relocation
scheme for mx51evk.
- Correct IRAM base address and add size definition
The IRAM starts from 0x1FFE0000 on final revsion i.mx51 than
0x1FFE8000 which is for older revision.
- Include imx-regs.h in mx51evk.h
Definitions like CSD0_BASE_ADDR and IRAM_BASE_ADDR can be
referred to.
- Define CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE
They are used to define init RAM layout.
- Remove comment for CONFIG_SYS_GBL_DATA_SIZE which has been
buried by Wolfgang's commit below
25ddd1fb: Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value
Signed-off-by: Shawn Guo <shawn.gsc@gmail.com>
This patch is to consolidate default mx51evk env for two primary
boot modes, mmcboot and netboot.
It also cleans some unused env like netdev, uboot and redundant
env like loadaddr since CONFIG_LOADADDR already defines it.
Signed-off-by: Shawn Guo <shawn.gsc@gmail.com>
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.
No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
The handling of the SPI_CPOL bit inside the SPI
driver was wrong. As reported by the manual,
the meaning of the SSPOL inside the
configuration register is the same as reported
by SPI specification (0 if low in idle, 1 is high
on idle). The driver inverts this logic.
Because this patch sets the logic as specified, it is required
to clear the CPOL bit in the configuration file to adapt
to the correct logic.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: David Jander <david.jander@protonic.nl>
The lowlevel_init file contained some hard-coded values
to setup the RAM. These board related values are moved into
the board configuration file.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The patch adds initial support for the Freescale mx51evk board.
Network (FEC) and SD controller (fsl_esdhc) are supported.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fred Fan <fanyefeng@gmail.com>
