Disable the non-existent ethernet ports on T4240RDB:FM1_DTSEC5,
FM1_DTSEC6, FM2_DTSEC5 and FM2_DTSEC6.
Signed-off-by: Ying Zhang <ying.zhang22455@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Extending Kconfig for adding new platform is a lot of work
for nothing. Setting SYS_CONFIG_NAME directly in Kconfig and
remove all dependencies on TARGET_ZYNQ_* options including SPL.
As a side-effect it also remove custom init folder for ps7_init_gpl.*
files. Folder is chosen based on device-tree file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Support RAM and MMC boot mode in SPL also with SPL_FIT images.
In MMC boot mode two boot options are available:
1) Boot flow with ATF(EL3) and full U-Boot(EL2):
aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin
mkimage -A arm64 -O linux -T kernel -C none -a 0xfffe5000 -e 0xfffe5000
-d bl31.bin atf.ub
cp spl/boot.bin <sdcard fat partition>
cp atf.ub <sdcard fat partition>
cp u-boot.bin <sdcard fat partition>
2) Boot flow with full U-Boot(EL3):
cp spl/boot.bin <sdcard>
cp u-boot*.img <sdcard>
3) emmc boot mode
dd if=/dev/zero of=sd.img bs=1024 count=1024
parted sd.img mktable msdos
parted sd.img mkpart p fat32 0% 100%
kpartx -a sd.img
mkfs.vfat /dev/mapper/loop0p1
mount /dev/mapper/loop0p1 /mnt/
cp spl/boot.bin /mnt
cp u-boot.img /mnt
cp u-boot.bin /mnt
cp atf.ub /mnt
umount /dev/mapper/loop0p1
kpartx -d sd.img
cp sd.img /tftpboot/
and program it via u-boot
tftpb 10000 sd.img
mmcinfo
mmc write 10000 0 $filesize
mmc rescan
mmc part
ls mmc 0
psu_init() function contains low level SoC setup generated for every HW
design by Xilinx design tools. xil_io.h is only supporting file to fix
all dependencies from tools. The same solution was used on Xilinx Zynq.
The patch also change CONFIG_SYS_INIT_SP_ADDR to the end of OCM which
stays at the same location all the time.
Bootrom expects starting address to be at 0xfffc0000 that's why this
address is SPL_TEXT_BASE.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for on board eeprom with programmed MAC for using in u-boot
to have uniq address for every board.
Most of the time uniq MAC address is on a label on the board.
If address is not programmed use these command to program it.
On zcu102:
ZynqMP> mm.b 0
00000000: 00 ? 00
00000001: a0 ? 0a
00000002: 35 ? 35
00000003: 02 ? 02
00000004: 00 ? ef
00000005: 00 ? 67
00000006: 00 ? q
i2c dev 5
i2c write 0 54 20 6
i2c md 54 20
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change the clock source of the SDHCI's generated clock from PLLA to
UPLL clock to align to Linux driver.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Fix the missing pin config of the SDMMC0 interface.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
The board supports following features:
- Boot media support: NAND Flash/SPI Flash
- Support ethernet
- Support USB mass storage
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Override the default product name U-Boot reports in the SMBIOS
table, to be compatible with the Intel provided UEFI BIOS, as
Linux kernel drivers (drivers/mfd/intel_quark_i2c_gpio.c and
drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c) make use of
it to do different board level configuration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Let git ignore dsdt.aml, dsdt.asl.tmp and dsdt.c files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable ACPI table generation by creating a DSDT table for all baytrail
boards: conga-qeval20-qa3-e3845, bayleybay and minnowmax.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
We always build for a mips32 or higher ISA, so this ".set mips32"
directive is redundant. Once MIPSr6 support is added it will become
harmful since some instruction encodings change & this directive will
cause the older encodings to be incorrectly emitted instead of the
appropriate ones for the build.
In preparation for supporting MIPSr6, remove this redundant directive.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Add support for the TPLink WDR4300 router, which is based on the
AR9344 MIPS 74Kc CPU and has 128 MiB of RAM. The USB is supported
on this system as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wills Wang <wills.wang@live.com>
This patch add board-level code and base DT for AP143.
Signed-off-by: Wills Wang <wills.wang@live.com>
[updated defconfig, enabled CONFIG_USE_PRIVATE_LIBGCC=y]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch add board-level code and base DT for AP121.
Signed-off-by: Wills Wang <wills.wang@live.com>
[updated defconfig, enabled CONFIG_USE_PRIVATE_LIBGCC=y]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add layout definitions and implement functions for field printing/updating,
layout detection, layout assignment, and layout parsing.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
To use AQR105 PHY's interrupt, we need to invert the IRQ pin polarity
by setting relative bit in SCFG_INTPCR register, because AQR105
interrupt is low active but GIC accepts high active.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some SOCs, specifically the ones in the C29x familiy can have
multiple security engines. This patch adds a system configuration
define which indicates the maximum number of SEC engines that
can be found on a SoC.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Using u16 for cfg_rcw_src and u8 for sd1refclk_sel is enough.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
gd->env_addr will be initialized in env_init() in
common/env_nowhere.c if CONFIG_ENV_IS_NOWHERE is defined.
So no need to do it again.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The current 'cpld reset' will just write global_rst register
but couldn't switch to NOR boot if the board's switches are
for NAND/SD boot. So need to write rcw source registers for
NOR boot as well.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Mix usage of uint32_t and u32 fixed in favor of u32.
Signed-off-by: Vincent Siles <vincent.siles@provenrun.com>
Reviewed-by: York Sun <york.sun@nxp.com>
On the LS102x boards, in order to initialize the ICID values of
masters, the dev_stream_id array holds absolute offsets from the
base of SCFG.
In ls102xa_config_ssmu_stream_id, the base pointer is cast to
uint32_t * before adding the offset, leading to an invalid address.
Casting it to void * solves the issue.
Signed-off-by: Vincent Siles <vincent.siles@provenrun.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update MAINTAINERS file for ls2080aqds and ls2080ardb platforms.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Optimize DDR timing for good margins to support new Transcend
and Apacer DDR4 UDIMM besides current Micron UDIMM.
Verified 1333MT/s, 1600MT/s, 1866MT/s, 2133MT/s rate with
following UDIMM on LS2080ARDB.
- Micron UDIMM: MTA18ASF1G72AZ-2G1A1Z
- Apacer UDIMM: 78.C1GM4.AF10B
- Transcend UDIMM: TS1GLH72V1H
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This option currently enables both the command and the SCSI functionality.
Rename the existing option to CONFIG_SCSI since most of the code relates
to the feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
While the driver-model block device support is in progress, it is useful to
build sandbox both with and without CONFIG_BLK. Add a separate board for
the latter.
Signed-off-by: Simon Glass <sjg@chromium.org>
This imports v11 of "Jetson TK1 Development Platform Pin Mux" from
https://developer.nvidia.com/embedded/downloads.
The new version defines the mux option for the MIPI pad ctrl selection.
The OWR pin no longer has an entry in the configuration table because
the only mux option it support is OWR, that feature isn't supported, and
hence can't conflict with any other pin. This pin can only usefully be
used as a GPIO.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
ABB should be initialized for all required domains voltage domain
for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If
we do not do this, kernel configuring just the frequency using the
default boot loader configured voltage can fail on many corner lot
units and has been hard to debug. This specifically is a concern with
DRA7 generation of SoCs since other than VDD_MPU, all other domains
are only permitted to setup the voltages to required OPP only at boot.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
ABB TX_DONE mask will vary depending on ABB module. For example,
3630 never had ABB on IVA domain, while OMAP5 does use ABB on MM domain,
DRA7 has it on all domains with the exception of CORE, RTC.
Hence, move the txdone mask definition over to structure describing
voltage domain.
Signed-off-by: Nishanth Menon <nm@ti.com>
This patch updates and simplifies the hikey README. The old
instructions were hard to follow, and convoluted.
This patch also updates the link to the mcuimage.bin which was outdated.
Using an outdated mcuimage.bin results in the additional a53 cores
not coming online when the kernel issues PSCI requests to
arm trusted firmware (ATF).
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The memory node gets automatically generated by U-Boot
in arch_fixup_fdt(), before passing control to the kernel
using U-Boots representation of the dram banks.
However the upstream kernel uses the memory node to carve-out
regions of RAM for various purposes. To make this work without
changing arch_fixup_fdt() which will effect many platforms
we replicate the upstream memory node layout using the dram
banks.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently only the serial pl01x driver is using DT,
and the other drivers still use platform data but
as more DT lands in the upstream kernel the aim is
to migrate the other drivers over to DT as well to
have a fully DT configured hikey u-boot.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds myself as maintainer for the hikey
U-Boot port.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for Technexion's PICO-IMX6UL-EMMC board.
For information about this board, please visit:
http://www.technexion.com/products/pico/pico-som/pico-imx6-emmc
Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
On a reset/reboot, the display power needs to be off for atleast 500ms
before turning it back on. So add a delay to the boot process to meet
the display timing requirement.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
To generate accurate pixel clocks required by the displays we need to
set the ldb_di_clk source on bx50v3 to PLL3 and b850v3 to PLL5. Since
PLL5 is disabled on reset, we need to enable PLL5.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
B450v3/B650v3 uses single channel LVDS and does not support HDMI.
B850v3 uses dual channel LVDS and supports HDMI. Hence split the display
setup into two different functions.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
Certain pins are not used on the i.MX6, and should have a neutral
pad configuration in order to reduce electrical interference on
the board. This commit defines these pins with a default value
rather than relying on the system defaults.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
Apparently, all "dave"-related vendor content was removed in commit
5344cc1a82fcc2817d4671696b3939b0dfa4323e; remove remaining directory
board/dave/, which consists solely of board/dave/common/flash.c.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Not all Keystone2 devices has AEMIF NAND controller. So adding Kconfig
entry for CONFIG_TI_AEMIF and enabling it in respective defconfigs on
platforms with AEMIF controller.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The AM572x-IDK board (Industrial Dev Kit) is a board based on TI's AM5728x
SOC which has a dual core 1.5GHz A15 processor. This board is a development
platform for the Industrial market with:
- 2GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector
The link to the data sheet and TRM can be found here:
http://www.ti.com/product/AM5728
NOTE: DT support is still pending upstream kernel acceptance but we
should be able to get the base system support with this patch.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update EMIF data based on recommendations from the now standard TI
EMIF tool version 1.1.1 based on 256MBx16 DDR3L Kingston D2516EC4BXGGB
data sheet
Update T_RRD from 5 to 6 based on AM57xx TRM -
Minimum number of DDR cycles from activate to ativate for a different
bank, minus 1.
Update T_CKESR from 4 to 3 based on AM57xx TRM - Minimum number of DDR
clocks cycles for which SDRAM must remain in self refresh, minus 1.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- Move the CONS_INDEX selection out of CONFIG_SYS_EXTRA_OPTIONS and
into Kconfig proper.
- Edit the relevant am57x configs to remove the now unneeded
CONFIG_SYS_EXTRA_OPTIONS.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update dm test command with pytest instead of ./test/dm/test-dm.sh
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Including netdev.h is causing compilation warning:
+ int fecmxc_register_mii_postcall(struct eth_device *dev, int
(*cb)(int));
+ ^
w+In file included from ../board/xilinx/zynqmp/zynqmp.c:9:0:
w+../include/netdev.h:204:41: warning: ‘struct eth_device’ declared
inside parameter list [enabled by default]
w+../include/netdev.h:204:41: warning: its scope is only this definition
or declaration, which is probably not what you want [enabled by default]
This patch removes it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define u64 types to be usable on 32bit system because of 64bit address
and size cells and 32bit shifts in the code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This line is not needed, as the board supports DT based probing. And
here the "Model:" is already printed:
Model: Marvell Armada XP theadorable
Board: theadorable
One line for the board name is enough.
Signed-off-by: Stefan Roese <sr@denx.de>
Sometimes the PCIe link for the PEX-switch will not come-up. In this case,
the board is not in a usable state. This patch makes sure that in this
case a soft-reset is issued. If this soft-reset does not result in the
PEX-switch being detected after some soft-reset cycles, an I2C message
is sent to the uC to issue a complete power-cycle of the board.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds an USB power toggle for theadorable. Additionally, the
USB PHY RX Channel Control 0 Register is changed to fix some issues
noticed while accessing some specific USB sticks.
Signed-off-by: Stefan Roese <sr@denx.de>
The Orange Pi One SBC, is a stripped down version of the popular
Orange Pi PC. The one is a H3 based SBC, with 512M of RAM,
micro-sd slot, 1 host usb, 1 otg usb, hdmi and 100Mbit ethernet.
The dts is identical to the dts submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Some boards have on board usb devices which need longer than the USB
spec's 1 second to connect from board powerup. Add a config option which
when non 0 adds an extra delay before the first usb bus scan.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Now that rpi_*defconfig and Kconfig (rather than the config header file)
provide the identity of the build, we don't need to separate config
headers and board directories for each RPi variant. Set CONFIG_SYS_BOARD
and CONFIG_SYS_CONFIG_NAME so that we can get rid of the duplication. This
requires a tiny number of extra ifdefs in the config header.
The only disadvantage of this approach is that the $board/$board_name
environment variables aren't as descriptive as they used to be. This isn't
really an issue because those only exist to allow scripts to create DTB
filenames at runtime. However, the RPi board code already sets $fdtfile to
something more accurate based on FW-reported board ID anyway.
While at it, unify some Kconfig select options, and add a MAINTAINERS
entry for bcm283x too.
Partially-suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
init_sata() is done as part of scsi_init() in
arch/arm/cpu/armv7/omap-common/sata.c so no need to duplicate
it here.
This seems to fix SATA problems in the kernel when CONFIG_TI_PIPE3 is
configured as loadable module.
Cc: Cooper Jr., Franklin <fcooper@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
On all Pis so far, the VC FW provides a short stub to set up the ARM CPU
before entering the kernel (a/k/a U-Boot for us). This feature is not
currently supported by the VC FW when booting in 64-bit mode. However,
this feature will likely appear in the near future, and this U-Boot port
assumes that such a feature is in place. Without that feature, or a
temporary workaround described below, U-Boot will not boot.
Once the VC FW does provide the ARM stub, u-boot.bin built for rpi_3 can
be used drectly as kernel7.img, in the same way as any other RPi port. The
following config.txt is required:
# Fix mini UART input frequency, and setup/enable up the UART.
# Without this option, U-Boot will not boot, even if you don't care
# about the serial console. This option will always be required for
# all RPi3 use-cases, unless the PL011 UART is used, which is not
# yet supported by rpi_3* builds of U-Boot.
enable_uart=1
# Boot in AArch64 (64-bit) mode.
# It is possible that a future VC FW will remove the need for this
# option, instead auto-setting 32-/64-bit mode based on the "kernel"
# filename present on the SD card.
arm_control=0x200
Prior to the VC FW providing the ARM boot stub, you can use the following
steps to build an equivalent stub into the U-Boot binary:
git clone https://github.com/swarren/rpi-3-aarch64-demo.git \
../rpi-3-aarch64-demo
(cd ../rpi-3-aarch64-demo && ./build.sh)
Build U-Boot for rpi_3 in the usual way
cat ../rpi-3-aarch64-demo/armstub64.bin u-boot.bin > u-boot.bin.stubbed
Use u-boot.bin.stubbed as kernel7.img on the Pi SD card.
In this case, the following additional entries are required in config.txt:
# Tell the FW to load the kernel image at address 0, the reset vector.
kernel_old=1
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The currently present DRAM timings generated from GHRD 14.0 did
not work on SoCkit rev. D because they were too tight. Load the
DRAM timings from GHRD 13.0 which are more relaxed and work with
SoCkit rev. D.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
LS2080A is the primary SoC, and LS2085A is a personality with AIOP
and DPAA DDR. The RDB and QDS boards support both personality. By
detecting the SVR at runtime, a single image per board can support
both SoCs. It gives users flexibility to swtich SoC without the need
to reprogram the board.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
When setting fixed-link property to DTS, the values should be converted
with using cpu_to_fdt32 so that to have correct value on little endian
Soc.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Read information about memory from DT. This patch simplify life with
synchronization between DT and board files.
dram_init() only needs maximum RAM size below 4GB that's why please sort
banks in memory node.
dram_init_banksize() copies memory setup to bi_dram[].
This will avoid reading information from DT twice.
Memory test start/end were changed to DDR location to let memtest still
compiled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is incorrect setting for USB which didn't work with origin
ps7_init_gpl.X files.
Use default setting for Digilent Zybo projects with HDMI in PL.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Provide board specific option how to read MAC address from ROM.
Do it in generic way to be reusable by differnet boards.
If this is not enough board specific functions can be created.
Signed-off-by: Joe Hershberger <joe.hershberger@gmail.com> # driver part
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds basic support for the Marvell A375 eval board. Tested
are the following interfaces:
- I2C
- SPI
- SPI NOR
- Ethernet (mvpp2), port 0 & 1
Currently the A375 SerDes and DDR3 init code is not intergrated. So
the SPL U-Boot is not fully functional.
Right now, this A375 mainline U-Boot can only be used by chainloading
it via the original Marvell U-Boot. This can be done via this
command:
=> tftpboot 00800000 a375/u-boot-dtb.bin;go 00800000
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Having had a similar board and memory part under logic analyzer, a
tINIT3 violation was measured. The fix was involved keeping tXPR and
SDE_to_RST at the power-on defaults and setting RST_to_CKE the JEDEC
value for LPDDR2. There was also a tIH-CA violation and this was
resolved by writing the default value in rather than what the script
here uses.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Having had a similar board and memory part under logic analyzer, a
tINIT3 violation was measured. The fix was involved keeping tXPR and
SDE_to_RST at the power-on defaults and setting RST_to_CKE the JEDEC
value for LPDDR2.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
enable_lvds() function only set bits IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT and
IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT, but these bits were already set
previously inside setup_display().
We can safely remove enable_lvds() then.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
This commit add support for 96Boards Dragonboard410C.
It is board based on APQ8016 Qualcomm SoC, complying with
96boards specification.
Features (present out of the box):
- 4x Cortex A53 (ARMv8)
- 2x USB Host port
- 1x USB Device port
- 4x LEDs
- 1x HDMI connector
- 1x uSD connector
- 3x buttons (Power, Vol+, Vol-/Reset)
- WIFI, Bluetooth with integrated antenna
- 8GiB eMMC
U-Boot boots chained with fastboot in 64-bit mode.
For detailed build instructions see readme.txt in board directory.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
Most of ehci-fsl header describe USB controller
designed by Chipidea and used by various SoC vendors.
This patch renames it to a generic header: ehci-ci.h
Contents of file are not changed (so it contains several
references to freescale SoCs).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
Enable the TI DP83867 Giga bit phy on the
dra7 rev c board. The rx and tx internal
delays are need for this board so the usage
of RGMII_ID is required.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This moves the sniper board from the lge to lg, in order to match the devicetree
vendor prefix already defined in the kernel.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
With the previous implementation, rebooting without registering a recognized
reboot mode would end up with U-Boot checking for a valid power-on reason, which
might result in the device turning off (e.g. with no USB cable attached and no
buttons pressed).
Since this approach is not viable (breaks reboot in most cases), the validity of
the reboot reason is checked (in turn, by checking that a warm reset happened,
as there is no magic) to detect a reboot and the 'o' char is recognized to
indicate that power-off is required. Still, that might be overridden by the
detection of usual power-on reasons, on purpose.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
With the previous implementation, rebooting without registering a recognized
reboot mode (despite registering the magic) would end up with U-Boot checking
for a valid power-on reason, which might result in the device turning off (e.g.
with no USB cable attached and no buttons pressed).
This was designed to catch reboots that are actually intended to be power-off,
something that old Android kernels do, instead of properly turning the device
off using the TWL4030.
However, since this approach is not viable (breaks reboot in most cases), the
validity of the reboot mode magic is checked to detect a reboot and the 'o' char
is recognized to indicate that power-off is required. Still, that might be
overridden by the detection of usual power-on reasons, on purpose.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The Raspberry Pi 3 contains a BCM2837 SoC. The BCM2837 is a BCM2836 with
the CPU complex swapped out for a quad-core ARMv8. This can operate in 32-
or 64-bit mode. 32-bit mode is the current default selected by the
VideoCore firmware on the Raspberry Pi 3. This patch adds a 32-bit port of
U-Boot for the Raspberry Pi 3.
>From U-Boot's perspective, the only delta between the RPi 2 and RPi 3 is a
change in usage of the SoC UARTs. On all previous Pis, the PL011 was the
only UART in use. The Raspberry Pi 3 adds a Bluetooth module which uses a
UART to connect to the SoC. By default, the PL011 is used for this purpose
since it has larger FIFOs than the other "mini" UART. However, this can
be configured via the VideoCore firmware's config.txt file. This patch
hard-codes use of the mini UART in the RPi 3 port. If your system uses the
PL011 UART for the console even on the RPi 3, please use the RPi 2 U-Boot
port instead. A future change might determine which UART to use at
run-time, thus allowing the RPi 2 and RPi 3 (32-bit) ports to be squashed
together.
The mini UART has some limitations. One externally visible issue in the
BCM2837 integration is that the UART divides the SoC's "core clock" to
generate the baud rate. The core clock is typically variable, and under
control of the VideoCore firmware for thermal management reasons. If the
VC FW does modify the core clock rate, UART communication will be
corrupted since the baud rate will vary from the expected value. This was
not an issue for the PL011 UART, since it is fed by a fixed 3MHz clock. To
work around this, the VideoCore firmware can be told not to modify the SoC
core clock. However, the only way this can happen and be thermally safe is
to limit the core clock to a low/minimum frequency. This leaves
performance on the table for use-cases that don't care about a UART
console. Consequently, use of the mini UART console must be explicitly
requested by entering the following line into config.txt:
enable_uart=1
A recent version of the VC firmware is required to ensure that the mini
UART is fully and correctly initialized by the VC FW; at least
firmware.git 046effa13ebc "firmware: arm_loader: emmc clock depends on
core clock See: https://github.com/raspberrypi/firmware/issues/572".
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This allows U-Boot to known the name of the board.
The existing rpi_2_defconfig can operate correctly on the Raspberry Pi 3
in 32-bit mode /if/ you have configured the firmware to use the PL011 UART
as the console UART (the default is the mini UART). This requires two
things:
a) config.txt should contain dtoverlay=pi3-miniuart-bt
b) You should run the following to tell the VC FW to process DT when
booting, and copy u-boot.bin.img (rather than u-boot.bin) to the SD card
as the kernel image:
path/to/kernel/scripts/mkknlimg --dtok u-boot.bin u-boot.bin.img
This works as of firmware.git commit 046effa13ebc "firmware: arm_loader:
emmc clock depends on core clock See:
https://github.com/raspberrypi/firmware/issues/572".
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
