Commit graph

72846 commits

Author SHA1 Message Date
Michal Simek
c5465684b9 xilinx: Enable efi debug command
Enable EFI debug command to be able to setup various efi variables to avoid
software like grub.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:25 +02:00
Michal Simek
19eb739a20 ARM: bitmain: Enable saving variables to SD card
Board has NAND and SD interfaces which can be used for saving variables
too.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:25 +02:00
Michal Simek
060fc5c8a0 ARM: bitmain: Enable legacy u-boot format
Still legacy formats are used that's why enable them by default.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:25 +02:00
Michal Simek
9dcf2e5c0d ARM: bitmain: Enable nand and smcc drivers
Enable nand and smcc via DT.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:25 +02:00
T Karthik Reddy
d999a7b7b6 spi: xilinx_spi: Trivial fixes in axi qspi driver
Use __func__ instead for function name in debug.
Use Linux style u32 instead of uint32_t.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
Michal Simek
ce90654d1c xilinx: Sync DTs with Linux kernel
There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:

- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA

but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
T Karthik Reddy
dd4c642757 clk: zynqmp: Fix clk dump values
With "clk dump" command, few clocks are showing up incorrect values
and some clocks are displayed as "unknown".

Add missing clocks to zynqmp clock driver to display proper
clocks rates.

Implement a simple way to get clock source, instead of calling
functions. Change existing functions to this simple mechanism.

Fix gem clock name "gem_rx" to "gem_tx" which was incorrect.
Change dbf_fpd & dbf_lpd clk names to dbg_fpd & dbg_lpd.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
2021-03-30 12:03:24 +02:00
Amit Kumar Mahapatra
e2b71c382f arm64: zynqmp: Rename clocks as per the Arasan NAND driver
In zynqmp.dtsi file renamed "clk_sys" clock to "controller" and
"clk_flash" clock to "bus" as per upstreamed Arasan NAND driver.
This fixes NAND driver probe failure.

Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
Amit Kumar Mahapatra
fbf043d7e6 arm64: zynqmp: Update device tree properties for nand flash
Update the following device tree properties for nand flash

- Set software ecc mode.
- Set bch as ecc algo.
- Set read block to 0.

Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
Michal Simek
cde1aaeae2 arm64: zynqmp: Update psu_init for zcu1275
Update clock/pll setup, ddr, MIOs based on 2020.2 hw design.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
Michal Simek
9577b2edf3 arm64: zynqmp: Add idt 8a34001 chip to zcu208/zcu216
There is Linux driver for these chips that's why add it to device tree.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
Michal Simek
7a50093a44 arm64: zynqmp: Add missing psu inits for zcu208/216
Add missing configurations file for zcu208 and zcu216.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
Ashok Reddy Soma
d5843f26ac arm64: zynqmp: Add emmc specific parameters
EMMC will have bus-width 8 and it is non-removable in general. These
are missing from dt node. Add bus-width and non-removable parameters
to emmc node.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
Ashok Reddy Soma
8600dd8ad4 arm64: zynqmp: Increase size of malloc pool
size of malloc() pool for use before relocation is not sufficient
for ZynqMP mini u-boot with emmc configuration. Increase it to 4K.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
Ashok Reddy Soma
2df44bbbb5 xilinx: zynq: Enable time and timer commands
Enable time command to get the elapsed time and timer commands.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
Alexandre Vicenzi
a99d70c180 board: dts: rockchip: Add NanoPi M4B
Add initial support for NanoPi M4B, a minor revision of
the original NanoPi M4.

Commit details of rk3399-nanopi-m4b.dts sync from Linux 5.12-rc4:
"arm64: dts: rockchip: Add NanoPi M4B board"
(sha1: c7b03115003f7f337ab165542cee37148cf30a8a)

Signed-off-by: Alexandre Vicenzi <alexandre.vicenzi@suse.com>
Reviewed-by: Kever Yang <kever.yang@rock-cihps.com>
2021-03-30 16:53:00 +08:00
Xiaobo Tian
b69b9f3f54 arm64: rk3399: Add support NanoPi R4s
NanoPi R4s is SBC base on Rockchip RK3399 hexa-core processor with
dual-Core Cortex-A72 and Mali-T864 GPU with 4GiB(LPDDR4) of RAM, SD card support,
including 2 gigabit ethernet(RTL8211E 1Gbps - RTL8111H 1Gbps) and 2 USB 3.0 port.
port.It also has two GPIO headers which allows further peripherals to be used.

The devicetree file is taken of the rk3399 nanopi4 Linux kernel [1].

[1] e7a0959082

Signed-off-by: xiaobo <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:53:00 +08:00
Roger Pau Monné
253b151d48 odroid-go2: fix default FDT file path
The path in the Linux kernel dts directory is
rockchip/rk3326-odroid-go2.dtb.

That also seems to match the FDT path set on other boards (ie:
rock64-rk3328 for example).

Signed-off-by: Roger Pau Monne <royger@FreeBSD.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:53:00 +08:00
Roger Pau Monné
4e456fb636 odroid-go2: do not disable EFI
Remove the unset of the EFI loader, it's possible for U-Boot to
provide a EFI environment on this board, and it's also required by
the FreeBSD loader which mandated EFI on Aarch64.

Signed-off-by: Roger Pau Monné <royger@FreeBSD.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:53:00 +08:00
Christoph Muellner
8a5a88308d rockchip: rk3399-puma: Increase environment size to 16 kiB.
On Puma we have the environment at an offset of 16 kiB.
On the eMMC this gives us 16 kiB for the environment before the SPL starts.
On the SPI NOR we also have 16 kiB until end of flash.
So let's increase the environment size from 8 kiB to its maximum
of 16 kiB for both MMC and SPI NOR.

Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:53:00 +08:00
Christoph Muellner
1621afc84f rockchip: rk3399-puma: Restore correct VDD_LOG supply.
A commit from last year re-imported the DTS files form the upstream kernel.
By doing so the VDD_LOG regulator in the board's DTS was dropped.
Let's restore this, but move it into the u-boot overlay to prevent this
issue in the future.

Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:53:00 +08:00
Peter Robinson
98c7962291 rockchip: rk3399: rock960: explicitly disable SPI flash
The Rock960 doesn't have SPI flash on-board, but the bits
get enabled by default which means when booting we get
some errors. Explicitly disable it to stop the errors.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:53:00 +08:00
Peter Robinson
44e1ad40e9 include: configs: rk3399: drop a dangling comment
Drop a irrelevent comment now the related configs have moved
to the various config files.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:53:00 +08:00
Heiko Stuebner
439fdaa26a rockchip: lion: update board defconfig
Adds the needed target option and drivers needed for correct
bringup.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:53:00 +08:00
Heiko Stuebner
ba421b96a2 rockchip: rk3368: sync down rk3368-lion board devicetree from Linux
This brings the actual rk3368-lion devicetree files from Linux 5.10
instead of using something separate.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:53:00 +08:00
Heiko Stuebner
5aefa4af29 rockchip: rk3368: sync main rk3368 dtsi from Linux
This is the state as of v5.10 + the recently added timer0 phandle
targetted at the 5.12 merge window.

With this the non-mainline nodes like the dmc move to a separate
rk3368-u-boot.dtsi that is included from the board-specific
-u-boot.dtsi files, similar to how rk3399 does this.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:53:00 +08:00
Heiko Stuebner
1ebf106f40 rockchip: rk3368: sync clock dt-binding header from Linux
This is the state as of v5.10 in Linux.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:53:00 +08:00
Heiko Stuebner
ca7bb9dde7 rockchip: rk3368: move STACK_R_ADDR address and into Kconfig
With the STACK_R_ADDR at 0x600000 (6MB) we're competing with
with the loading address of either u-boot or atf parts, so move
that away to 0x4000000 (64MB) similar to rk3399.

Only lion currently sets that at all but not sheep the second
rk3368 board, so just move that to the Kconfig for rk3368 similar
to rk3399 as well.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:53:00 +08:00
Heiko Stuebner
53e14aa734 rockchip: rk3368: increase SYS_MALLOC_F_LEN to 0x4000
To prevent running out of memory, increase SYS_MALLOC_F_LEN to 0x4000
similar to what rk3399 uses.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:53:00 +08:00
Heiko Stuebner
e436c499dc rockchip: rk3368: set CONFIG_SYS_BOOTM_LEN to 64MB
Mimicing for example the rk3399, set the SYS_BOOTM_LEN to 64MB so
that regular kernel images can get loaded without problems.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:53:00 +08:00
Heiko Stuebner
a062144518 rockchip: rk3368: adjust CONFIG_SYS_LOAD_ADDR
CONFIG_SYS_LOAD_ADDR currently is at 0x00280000 which is only 512KB
behind the area where we load u-boot to, which depending on u-boot size
may overlap at some point.

So for safety just pick the same value rk3399 has and set
CONFIG_SYS_LOAD_ADDR to 0x00800800 on rk3368 as well.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:53:00 +08:00
Roger Pau Monné
19c6b8cf8b odroid-go2: remove setting SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
Using a non-default SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR setting makes the
resulting u-boot-rockchip.bin unbootable, as it gets stuck after SPL.
Removing the setting from the defconfig allows U-Boot to load
successfully.

Signed-off-by: Roger Pau Monné <royger@FreeBSD.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-03-30 16:52:59 +08:00
Robert Hancock
e8a212ac77 net: gem: Fix setting PCS auto-negotiation state
The code was trying to disable PCS auto-negotiation when a fixed-link node
is present and enable it otherwise. However, the PCS registers were being
written before the PCSSEL bit was set in the network configuration
register, and it appears that in this state, PCS register writes are
ignored. The result is that the intended change only took effect on the
second network operation that was performed, since at that time PCSSEL is
already enabled.

Fix the order of register writes so that PCS registers are only written to
after the PCS is enabled.

Fixes: 26e62cc971 ("net: gem: Disable PCS autonegotiation in case of fixed-link")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 09:18:47 +02:00
Tom Rini
1057b1be75 Prepare v2021.04-rc5
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAmBiRbMACgkQFHw5/5Y0
 tyz0KAv/T8glQGL6L2CYeLuwbs9tndQoaH2YNb3teNUJrqehBleJAQ6ubHP30d87
 rHrokJ4Zu3TC15sACrK4GOMvsAVkeCuU/jIqFJA4ieDZr8g7yfUMOZMsDiIFdd36
 Rdmi71Jtek/csyS5BfcUUYoXVbUCGQ8yAx7z0VrK0sqsqZYYJNwPmqgkR8U2ulNb
 FiLxwamFwH7+bsvcvHajO1dOyko0zR7GTisf/fOgmlHuF3BldqG4SDcNd528uEWb
 r3fXs2Ut6IaC/beCnmKUPVG3ZjdPtb+T230rRRhUOfjTwqR7SzXp5bTyzdgyw3gU
 rOgfi/mAGQPPG2E2fzPz0JCI1irbnkSE2fVJ4epaVUCoHIEsQQdy034aD3qLcHFY
 65ihEpRvCM7s9jfKX8XeIG4rKFB4i60TX5orzdMvx7wV3rxmPE9qQmF9lkD+fEA+
 TPuFtkjGmluSe+xWBVK7+6xuF6rcLEbNXuFWRi3qMSMgH8rtGfeJRonusOGPolwC
 jQ1T7szW
 =UJ/O
 -----END PGP SIGNATURE-----

Merge tag 'v2021.04-rc5' into next

Prepare v2021.04-rc5
2021-03-29 18:00:21 -04:00
Tom Rini
d8eafb16c8 Prepare v2021.04-rc5
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-03-29 17:20:13 -04:00
Tom Rini
4906238191 binman support for expanding entries, connections
misc fixes and improvements to sandbox, etc.
 x86 CBFS improvements
 x86 coreboot improvements
 -----BEGIN PGP SIGNATURE-----
 
 iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmBfg1YRHHNqZ0BjaHJv
 bWl1bS5vcmcACgkQfxc6PpAIreZQnQf/UtTgrFdmvY86v4Y3sCvbdAlDHso15voU
 zEwhjKoPbnchHDA0UMFn/SmP0zRZNQbIhIsASoC4OBVl8nmtAQ7nDP8SmwtV95Zo
 wqPVUlCjkHID3XOFIDbqx3L6fCL1mDe33hhfdYDzeLmhcDyxofY9yTjMasxk4tcu
 oMRMiFYpL6IkM7Jtey/kRzOuEykh1J/iXJ0rAHnzgHR8vzLJEo5DjLsbd971896I
 87LUmZ//3b499KgTCj7MYTEFoDA36MCPQKWqIhbFv4zh3STLGCT5fri6jHWqjHYG
 UU35bdgLvsE3Dv/VFg/C+YoIzbxGRYK5WCIJX4akoE/GPCgba0C9YQ==
 =5gak
 -----END PGP SIGNATURE-----

Merge tag 'dm-pull-28mar21' of git://git.denx.de/u-boot-dm into next

binman support for expanding entries, connections
misc fixes and improvements to sandbox, etc.
x86 CBFS improvements
x86 coreboot improvements
2021-03-28 20:29:39 -04:00
Tom Rini
a7d3ac6148 Merge branch '2021-03-28-assorted-bugfixes' 2021-03-28 20:28:51 -04:00
Jessica Clarke
3b142045e8 Support building on macOS/arm64
On Arm-based Macs, -no_pie is ignored and gives a linker warning.
Moreover, the build falls over with:

  ld: Absolute addressing not allowed in arm64 code but used in '_image_type_ptr_aisimage' referencing '_image_type_aisimage'

for dumpimage and mkimage, since we put data structs in text sections
not data sections and so cannot have dynamic relocations. Instead, move
the sections to __DATA and drop disabling PIE.

Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2021-03-28 17:30:35 -04:00
Sean Anderson
6863c7f1b6 dm: test: Always include command.h for print_ut
We need this header for U_BOOT_CMD, which is always present even without
EFI.

Fixes: 82c468a049 ("dm: test: Update Makefile conditions")

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-03-28 17:30:35 -04:00
Simon Glass
3c2503ee33 test: Add udevice declaration to avoid build error
When including this file on a board other than sandbox (e.g by enabling
UNIT_TEST and CMD_SETEXPR) an results. Fix it by declaring struct udevice
first.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-03-28 17:30:35 -04:00
Tom Rini
31637e0bc0 Merge branch '2021-03-27-master-imports'
- Rework the deprecation warnings to be consistently phrased.
- Add in a warning for DM_I2C, for a year from next release.
- Fix Azure builds of Windows host tools.
2021-03-27 11:58:37 -04:00
Tom Rini
94d66d8b24 Azure: Use "pacman -Sy" to install the toolchain
We now see an error such as:
warning: database file for 'ucrt64' does not exist (use '-Sy' to download)
error: failed to prepare transaction (could not find database)

So use -Sy as suggested.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2021-03-27 11:57:10 -04:00
Simon Glass
65c8cdc72b dm: i2c: Add a migration method for I2C
This probably should have been done a while back since it is a core
system. Add a migration deadline of later this year, to catch the
stragglers.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-03-27 09:51:22 -04:00
Simon Glass
782dac5b7d Makefile: Drop the old SPI flash migration message
This message does not seem to make sense. It may be out of date. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-03-27 09:48:26 -04:00
Simon Glass
8cd1874f4c Makefile: Use common code for DM_ETH deprecation warning
Update the CONFIG_DM_ETH check to use the 'deprecated' function.

Tested with snow

Old message:

===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

New message:

===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-03-27 09:48:26 -04:00
Simon Glass
78b4a564cb Makefile: Use common code for WDT deprecation warning
Update the CONFIG_WDT check to use the 'deprecated' function.

Tested with kmcent2

Old message:

===================== WARNING ======================
This board does not use CONFIG_WDT (DM watchdog support).
Please update the board to use CONFIG_WDT before the
v2019.10 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

New message:

===================== WARNING ======================
This board does not use CONFIG_WDT (Driver Model
for DM watchdog). Please update the board to use
CONFIG_WDT before the v2019.10 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-03-27 09:48:26 -04:00
Simon Glass
ec384f9f12 Makefile: Use common code for SPI_FLASH deprecation warning
Update the CONFIG_DM_SPI_FLASH check to use the 'deprecated' function.

Tested with vinco

Old message:

===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

New message:

===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH (Driver Model
for SPI flash). Please update the board to use
CONFIG_DM_SPI_FLASH before the v2019.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-03-27 09:48:26 -04:00
Simon Glass
d13aee07fd Makefile: Use common code for DM_VIDEO deprecation warning
Update the CONFIG_DM_VIDEO check to use the 'deprecated' function.

Tested with pxm2

Old message:

===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

New message:

===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO (Driver Model
for video). Please update the board to use
CONFIG_DM_VIDEO before the v2019.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
==================================================

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-03-27 09:48:26 -04:00
Simon Glass
39e526a8ec Makefile: Use common code for PCI deprecation warning
Update the CONFIG_DM_PCI check to use the 'deprecated' function.

Tested with MPC8349ITX

Old message:

===================== WARNING ======================
This board does not use CONFIG_DM_PCI Please update
the board to use CONFIG_DM_PCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

New message:

===================== WARNING ======================
This board does not use CONFIG_DM_PCI (Driver Model
for PCI). Please update the board to use
CONFIG_DM_PCI before the v2019.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-03-27 09:48:26 -04:00
Simon Glass
099288bf78 Makefile: Use common code for LIBATA deprecation warning
Update the CONFIG_LIBATA check to use the 'deprecated' function.

Tested with MPC8349ITX

Old message:

===================== WARNING ======================
This board does use CONFIG_LIBATA but has CONFIG_AHCI not
enabled. Please update the storage controller driver to use
CONFIG_AHCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

New message:

===================== WARNING ======================
This board does not use CONFIG_AHCI (Driver Model
for AHCI). Please update the board to use
CONFIG_AHCI before the v2019.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-03-27 09:48:26 -04:00