Commit graph

268 commits

Author SHA1 Message Date
Moses Christopher
b1476b52b3 am335x, guardian: update guardian board
- add BOARD_LATE_INIT function calls in board.c
  - add swi_status detection in board.c
  - mux: add guardian interfaces to single pinmux structure
  - am33xx, kconfig: add BOARD_LATE_INIT for GUARDIAN board

Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-10-11 13:31:17 -04:00
Krunal Bhargav
2b2e1573cf arm: omap: emif-common: Fix memory priming for ECC
Before the priming begins, we need to disable RMW (Read Modify Write)
and disable ECC verification for read accesses. By default, the EMIF
tool enables RMW and read accesses in the EMIF_ECC_CTRL_REG.

Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 13:31:17 -04:00
Krunal Bhargav
d0a37a5e51 arm: omap: emif-common: Disable interleaving
If ECC is enabled, we need to ensure interleaving is disabled for higher
address space.

Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 13:31:17 -04:00
Lokesh Vutla
ed474ae00c arm: omap: emif-common: Fix ecc address calculation
ecc_address_range registers contains the start address and end address
of the DDR address space. But the ddr driver is assuming the register
contains the start address and size of the DDR address space. Because
of this the ecc enabling is failing for the 2nd range of ecc addresses.
Fix this calculation.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 13:31:17 -04:00
Simon Glass
27084c03d3 spl: Allow tiny printf() to be controlled in SPL and TPL
At present there is only one control for this and it is used for both SPL
and TPL. But SPL might have a lot more space than TPL so the extra cost of
a full printf() might be acceptable.

Split the option into two, providing separate SPL and TPL controls. The
TPL setting defaults to the same as SPL.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-08 13:57:45 +08:00
Suman Anna
a517c1f62f ARM: DRA7: Fixup DPLL clock rate fixup logic for newer kernels
The commit 1b42ab3eda ("ARM: DRA7: Fixup DSPEVE, IVA and GPU clock
frequencies based on OPP") updates the kernel device-tree blob to adjust
the DSP, IVA and GPU DPLL clocks based on a one-time OPP choice selected
in U-Boot. All these DPLL clocks are children of the cm_core_aon clocks
DT node.

The hierarchy of this clocks DT node has changed in newer Linux kernels
starting from v5.0, and this results in a failure in ft_fixup_clocks()
function to update the clock rates on these newer kernels. Fix this by
updating the lookup logic to look through both the newer and older
DT hierarchy paths for the cm_core_aon clocks node.

Signed-off-by: Suman Anna <s-anna@ti.com>
2019-08-20 11:46:38 -04:00
Tom Rini
9c6115822e Merge branch '2019-08-11-ti-imports'
- More DaVinci updates and fixes
- PCIe support on am65x
- Watchdog converted to DM
- Assorted other bugfixes
2019-08-12 18:47:53 -04:00
Hannes Schmelzer
60df809f62 board/BuR/brsmarc1: initial commit
This commit adds support for the B&R brsmarc1 SoM.

The SoM is based on TI's AM335x SoC.
Mainly vxWorks 6.9.4.x is running on the board,
doing some PLC stuff on various carrier boards.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
2019-08-12 13:33:37 -04:00
Suniel Mahesh
6912f2a8ae watchdog: omap_wdt: Disable DM watchdog support in SPL
This patch disables DM watchdog support for SPL builds and uses
the legacy omap watchdog driver on TI AM335x chipsets.

The following build error is reported if DM watchdog support was
enabled in SPL:

  CC      spl/drivers/usb/gadget/rndis.o
  LD      spl/drivers/usb/gadget/built-in.o
  LD      spl/drivers/usb/musb-new/built-in.o
  LD      spl/drivers/built-in.o
  LD      spl/u-boot-spl
arm-linux-ld.bfd: u-boot-spl section .u_boot_list will not fit in region .sram
arm-linux-ld.bfd: region .sram overflowed by 440 bytes
make[1]: *** [spl/u-boot-spl] Error 1
make: *** [spl/u-boot-spl] Error 2

Adjusted WATCHDOG_RESET macro accordingly. Earlier it was pointing
to hw_watchdog_reset. Since CONFIG_WATCHDOG replaces CONFIG_HW_WATCHDOG,
now WATCHDOG_RESET macro points to watchdog_reset. This watchdog_reset
is not defined anywhere for am33xx/omap2 and needs to be defined. Fixed
this by simply calling hw_watchdog_reset in watchdog_reset.

Built and tested on AM335x device (BeagleboneBlack), compile tested for
all other AM33xx/omap2 based boards.

Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
[trini: Fix watchdog.h logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-12 13:27:55 -04:00
Simon Glass
e7dcf5645f env: Drop environment.h header file where not needed
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-11 16:43:41 -04:00
Simon Glass
9fb625ce05 env: Move env_set() to env.h
Move env_set() over to the new header file.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-11 16:43:41 -04:00
Sam Protsenko
4347b0b0b2 omap: Correct the fastboot product var
"fastboot flashall" expects "fastboot getvar product" value to be one of
values provided in android-info.txt file (in AOSP), from "require
board=" list. Before this patch, "am57xx" is returned for all AM57xx
based boards, as it's set in $board env var from SYS_BOARD in
board/ti/am57xx/Kconfig file, which is used for default implementation
of "fastboot getvar product".

In order to fix that inconsistency, let's do next:
  1. In U-Boot: override fastboot.product, reusing the value from
     $board_name
  2. In AOSP: provide values for all AM57xx boards we can use to
     device/ti/beagle_x15/board-info.txt file

This way requirements check in "fastboot flashall" will work as
expected, verifying that user tries to flash images to the board which
those images were built for.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Acked-by: Andrew F. Davis <afd@ti.com>
2019-07-31 13:08:07 -04:00
Bartosz Golaszewski
e809285d49 net: davinci_emac: convert to using the driver model
Now that we removed all legacy boards selecting TI_EMAC we can
completely convert the driver code to using the driver model.
This patch also updates all remaining users of davinci_emac.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #am3517-evm & da850-evm
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2019-07-25 13:36:13 -05:00
Tom Rini
2a51e16bd5 configs: Make USE_TINY_PRINTF depend on SPL||TPL and be default
The USE_TINY_PRINTF symbol only changes things within SPL and TPL
builds, so make it depend on that support.  Next, make it default as
within these cases we should rarely have need of more advanced print
formats outside of the debug context.

To do this, in a few cases we need to correct our Kconfig dependencies
as we had cases of non-SPL targets select'ing this symbol.  Finally, in
the case of a few boards we really do need the full printf
functionality.

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-07-13 11:11:29 -04:00
Niel Fourie
6e171b661e ARM: am335x: Add phyCORE AM335x R2 support
Support for Phytech phyCORE AM335x R2 SOM (PCL060) on the Phytec
phyBOARD-Wega AM335x.

CPU  : AM335X-GP rev 2.1
Model: Phytec AM335x phyBOARD-WEGA
DRAM:  256 MiB
NAND:  256 MiB
MMC:   OMAP SD/MMC: 0
eth0: ethernet@4a100000

Working:
 - Eth0
 - i2C
 - MMC/SD
 - NAND
 - UART
 - USB (host)

Device trees were taken from Linux mainline:
commit 37624b58542f ("Linux 5.1-rc7")

Signed-off-by: Niel Fourie <lusus@denx.de>
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Marek Vasut <marex@denx.de>
2019-07-13 11:11:28 -04:00
Marek Vasut
b2a2bf41ac arm: mach-omap2: am33xx: Init pinmux before clock
The board_early_init_f() inits clock before initing pinmux. However,
the clock configuration code might need to adjust PMIC settings of a
PMIC on I2C bus (e.g. board/ti/am335x/board.c does that). If the I2C
bus pin muxing is not configured before attempting to communicate
with the PMIC, the communication will silently fail and the prcm_init()
may configure fast enough CPU clock that the default voltage provided
by the PMIC would be insufficient and the platform would become
unstable.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Tom Rini <trini@konsulko.com>
2019-07-11 14:11:20 -04:00
Adam Ford
33ac2b560b arm: omap3: Manually initialize GPIO if OF_CONTROL doesn't
The commong initialization code manually initializes the GPIO
even when OF_CONTROL does it, so we can reduce the code size a
bit by not doing it manually when we have device tree support.

Using the omap3_logic board (dm3730), the sizes shrunk:

Before:

   text	   data	    bss	    dec	    hex	filename
 561066	  28596	 116880	 706542	  ac7ee	u-boot
  55245	   1605	   1888	  58738	   e572	spl/u-boot-spl

After
  text	   data	    bss	    dec	    hex	filename
 560898	  28548	 116872	 706318	  ac70e	u-boot
  55121	   1557	   1888	  58566	   e4c6	spl/u-boot-spl

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-06-05 12:14:02 -04:00
Bartosz Golaszewski
d7cc0e4d79 mcx: remove board
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-05-28 13:58:06 -04:00
Bartosz Golaszewski
2aa20c43e4 twister: remove board
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2019-05-28 13:58:06 -04:00
Bartosz Golaszewski
899dd71e9f mt_ventoux: remove board
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2019-05-28 13:58:06 -04:00
Bartosz Golaszewski
8c2644ca69 cm_t3517: remove board
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-05-28 13:58:06 -04:00
Bartosz Golaszewski
5e92c6856b eco5pk: remove board
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-05-28 13:58:06 -04:00
Trevor Woerner
1001502545 CONFIG_SPL_SYS_[DI]CACHE_OFF: add
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.

Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-05-18 08:15:35 -04:00
Brad Griffis
1dbd9a7b17 arm: mach-omap2: am33xx: ddr: update value for ext_phy_ctrl_36
for suspend/resume robustness

update value for ext_phy_ctrl_36 for suspend/resume robustness
with hardware leveling enabled.

Match recommended values from EMIF Tools app note:

http://www.ti.com/lit/an/sprac70/sprac70.pdf

Signed-off-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-05-05 08:48:50 -04:00
Brad Griffis
7b5774e4bd arm: mach-omap2: am33xx: Disable EMIF_DEVOFF immediately before hw leveling
In case of RTC+DDR resume, need to restore EMIF context
before initiating hardware leveling.

Signed-off-by: Brad Griffis <bgriffis@ti.com>
[j-keerthy@ti.com Fixed the am335x build issues]
Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-05-05 08:48:50 -04:00
Brad Griffis
6fe3e5ba66 arm: mach-omap2: am33xx: Enable HW Leveling in the rtc+ddr path
Enable HW leveling in RTC+DDR path. The mandate is to enable
HW leveling bit and then wait for 1 ms before accessing any
register.

Signed-off-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-05-05 08:48:50 -04:00
Brad Griffis
84cf295f84 arm: mach-omap2: am33xx: ddr: Add 1ms delay to avoid L3 error
Add 1ms delay to avoid L3 timeout error during suspend resume.

Signed-off-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-05-05 08:48:50 -04:00
Brad Griffis
82195797a4 arm: mach-omap2: am33xx: ddr: programming of EXT_PHY_CTRL1 and EXT_PHY_CTRL1_SHADOW
Adjust DQS skew in case where invert_clkout=1 is used.
Match recommended values from EMIF Tools app note:

http://www.ti.com/lit/an/sprac70/sprac70.pdf

Signed-off-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-05-05 08:48:50 -04:00
Uri Mashiach
ecb76eff56 arm: am57xx: cl-som-am57x: remove board support
U-Boot support for the CL-SOM-AM57x module is no longer required.

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
2019-04-17 09:20:26 -04:00
Tom Rini
9c4b0131d1 ti: keystone2: Move CONFIG_ISW_ENTRY_ADDR to a common place
The ISW_ENTRY_ADDR Kconfig option under mach-omap2 isn't a SoC specific
notion but rather "where is our previous stage loaded in memory?"
option.  Make use of this on ARCH_KEYSTONE rather than SPL_TEXT_BASE for
our HS builds that are not using SPL anyhow.

Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com?
2019-04-12 08:05:55 -04:00
Sjoerd Simons
4512380420 am335x, guardian: Add support for the bosch guardian board
Add support for the Bosch Guardian board.

CPU  : AM335X-GP rev 2.1
Model: Bosch AM335x Guardian
I2C:   ready
DRAM:  256 MiB
NAND:  512 MiB
MMC:   OMAP SD/MMC: 0

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Felix Brack <fb@ltec.ch>
2019-04-12 08:05:48 -04:00
Abel Vesa
79536013a3 usb: Rename SPL_USB_SUPPORT to SPL_USB_STORAGE
Since there is the SPL_USB_HOST_SUPPORT for enabling USB support in SPL,
makes more sense to rename the SPL_USB_SUPPORT as SPL_USB_STORAGE.
Everything that is not part of the usb storage support in SPL is now
build under SPL_USB_HOST_SUPPORT.

Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-02-15 22:01:15 +01:00
Vignesh R
6d82517836 configs: Don't use SPI_FLASH_BAR as default
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:22 +05:30
Tien Fong Chee
f4b4092474 spl: Kconfig: Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPL_FS_EXT4
Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both
obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be
used to control the build in both SPL and U-Boot.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01 09:14:21 -05:00
Tien Fong Chee
0c3a9ed409 spl: Kconfig: Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.

Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-02-01 09:12:48 -05:00
Tom Rini
2f41ade79e linker: Modify linker scripts to be more generic
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than
CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE.  This lets us re-use the
same script for both SPL and TPL.  Add logic to scripts/Makefile.spl to
pass in the right value when preprocessing the script.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-01-26 22:55:53 -05:00
Andrew F. Davis
0fd1359c5a ARM: mach-omap2: Kconfig: Allow OMAP5 devices to set entry point
Like AM33xx and AM43xx, DRA7xx and AM57xx devices may need to
have an non-standard boot address in memory. This may be due
to the device being a high security variant, which place the
Initial SoftWare (ISW) after certificates and secure software.

Allow these devices to set this from Kconfig.

Signed-off-by: Andrew F. Davis <afd@ti.com>
2019-01-26 08:13:55 -05:00
Andrew F. Davis
6536ca4d66 spl: Kconfig: Drop the _SUPPORT postfix from SPL_DFU
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
2019-01-26 08:13:54 -05:00
Adam Ford
a1702746df ARM: mach-omap2: omap3: Fix GPIO clocking in SPL
OMAP3_GPIO_x is needed to enable each GPIO bank on the OMAP3
boards. At one point, the #ifdef's were replaced with
if CONFIG_IS_ENABLED but this won't work for people who need
OMAP3_GPIO_x in SPL since the SPL prefix for this option isn't
used in Kconfig.  This patch moves the check to #if defined and
also makes Kconfig select the banks if CMD_GPIO is used which
makes the checks in the code less cumbersome.

Fixes: bd8a9c14c9 ("arm: mach-omap2/omap3/clock.c: Enable
all GPIO with CMD_GPIO")

Reported-by: Liam O'Shaughnessy <liam.o.shaughnessy@gumstix.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Migrate omap3_igep00x0.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-12-26 21:20:48 -05:00
Jean-Jacques Hiblot
7a43dd7aa6 arm: am33xx: Register USB controllers if DM_USB is used but not OF_CONTROL
When DM_USB is used, either the USB controllers are bound when the DTB
is parsed (when OF_CONTROL is enabled) or they are bound using the
U_BOOT_DEVICES() macro.
In the later case, the platform data is passed in a struct ti_musb_platdata
because it cannot be read from the DTB.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-12-14 17:59:10 +01:00
Felix Brack
bfaaacd3b2 arm: am335x-pdu001: Move from embedded to separate DTB
There is no need for an embedded device tree for this board so let the
build process generate a separate u-boot.dtb file instead.

Signed-off-by: Felix Brack <fb@ltec.ch>
2018-12-12 12:14:23 -05:00
Jean-Jacques Hiblot
40ecdbc648 dra7: Allow selecting a new dtb after board detection.
The DRA7 platforms requires that the dtb used in the SPL really matches the
platform  to have the best MMC performances.
To detect the board type/version an I2C EEPROM is read. This requires that
DM is initialized before the detection. As a consequence we must reset the
DM after the board detection is a new dtb would better match the platform.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2018-12-10 07:27:25 +01:00
Jean-Jacques Hiblot
1514244cc1 ti: remove usage of DM_I2C_COMPAT and don't disable DM_I2C in SPL
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C
API when DM_I2C is used. The goal is to eventually remove DM_I2C_COMPAT
when all I2C "clients" have been migrated to use the DM API.
This a step in that direction for the TI based platforms.
Build tested with buildman:
buildman -dle am33xx ti omap3 omap4 omap5 davinci keystone

boot tested with:
am335x_evm, am335x_boneblack, am335x_boneblack_vboot (DM version),
am57xx_evm, dra7xx_evm, k2g_evm, am437x_evm

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2018-12-10 07:15:21 +01:00
Jean-Jacques Hiblot
2b30b38b26 omap: detect the board after DM is available
In order to use DM_I2C, we need to move the board detection after the
early SPL initialization.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2018-12-10 06:14:47 +01:00
Jean-Jacques Hiblot
0e6e67c667 am335x: Register the I2C controllers if DM_I2C is used.
If DM_I2C is used , the I2C controllers must be registered as U_BOOT_DEVICE
because OF_CONTROL is not used in the SPL.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2018-12-10 06:12:42 +01:00
Adam Ford
876ddb558d ARM: mach-omap2: Kconfig: Make SYS_MPUCLK dependent on AM33XX
This value is unly used in arch/arm/mach-omap2/am33xx/
clock_am33xx.c, so let's make it dependent on AM33XX since
that is the only way this file gets compiled into the code
according to the Makefile.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix symbol name]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-19 14:16:32 -04:00
Patrick Delaunay
6180ea7e66 arm: remove prototype for get_timer_masked
The interruption support had be removed for ARM architecture and
the function get_timer_masked() is no more used except in some
the timer.c files.

This patch clean each timer.c which implement this function and
remove the associated prototype in u-boot-arm.h

For timer.c, I don't verify if the weak version of get_timer
(in lib/time.c) can be used

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-10-10 13:35:09 -04:00
Adam Ford
668146128a ARM: mach-omap2: Don't initialize I2C if DM_I2C is enabled
boot-common.c checks to see if I2C is enabled in SPL, but
it doens't check for DM_I2C before initializing it.  This
will now only initialize the I2C is the DM_I2C is not enabled
to avoid initializing it more than once.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11 21:39:02 -04:00
Adam Ford
de39dc7162 arm: armv7-a: Compile and tune for armv7-a instead of armv5
arch/arm/Makefile references armv5 for backwards compatibility with
older compilers.  This patch removes those references to armv5,
since by now newer compilers are required which should have armv7
support enabled.

The Makefile also also has a list of options for mtune, but the
entry for CONFIG_CPU_V7A is empty, so this patch tunes the
CPU_V7A architecture to generic-armv7-a.

The following size changed apply to omap3_logic using GCC.

Stock
text data bss dec hex filename
50910 429 67580 118919 1d087 spl/u-boot-spl
540713 22700 327072 890485   d9675 u-boot

Without Armv5
text data bss dec hex filename
50916 429 67580 118925   1d08d spl/u-boot-spl
540719 22700 327064 890483   d9673 u-boot

mtune=generic-armv7-a
text data bss dec hex filename
50932 429 67580 118941   1d09d spl/u-boot-spl
540519 22700 327080 890299   d95bb u-boot

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-10 20:48:16 -04:00
Michal Simek
58008cbab5 Kconfig: Sort bool, default, select and imply options
Another round of sorting Kconfig entries aplhabetically.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-30 07:18:48 -04:00
Michal Simek
08a00cba06 dm: Change CMD_DM enabling
CMD_DM is used for debug purpose and it shouldn't be enabled by default
via Kconfig. Unfortunately this is in the tree for quite a long time
that's why solution is to use imply DM for all targets which are
enabling DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-30 07:18:48 -04:00
Michal Simek
5ed063d10f Kconfig: Sort bool, default, select and imply options
Fix Kconfig bool, default, select and imply options to be
alphabetically sorted.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-07-30 07:18:48 -04:00
Nishanth Menon
94c6a89a99 ARM: mach-omap2: omap3/am335x: Enable ACR::IBE on Cortex-A8 SoCs for CVE-2017-5715
Enable CVE-2017-5715 option to set the IBE bit. This enables kernel
workarounds necessary for the said CVE.

With this enabled, Linux reports:
CPU0: Spectre v2: using BPIALL workaround

This workaround may need to be re-applied in OS environment around low
power transition resume states where context of ACR would be lost (off-mode
etc).

Signed-off-by: Nishanth Menon <nm@ti.com>
2018-06-29 11:30:39 -04:00
Nishanth Menon
dbb7caf110 ARM: mach-omap2: omap5/dra7: Enable ACTLR[0] (Enable invalidates of BTB) to facilitate CVE_2017-5715 WA in OS
Enable CVE_2017_5715 and since we have our own v7_arch_cp15_set_acr
function to setup the bits, we are able to override the settings.

Without this enabled, Linux kernel reports:
CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable

With this enabled, Linux kernel reports:
CPU0: Spectre v2: using ICIALLU workaround

NOTE: This by itself does not enable the workaround for CPU1 (on
OMAP5 and DRA72/AM572 SoCs) and may require additional kernel patches.

Signed-off-by: Nishanth Menon <nm@ti.com>
2018-06-29 11:30:39 -04:00
Adam Ford
bd8a9c14c9 arm: mach-omap2/omap3/clock.c: Enable all GPIO with CMD_GPIO
When CMD_GPIO is enabled the command 'gpio status -a' can cause
a hang or reboot if GPIO banks are not enabled, because it scans
all banks.  This patch enables all GPIO banks so 'gpio status -a'
can fully execute.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-06-18 14:43:13 -04:00
Alex Kiernan
413b90777f ti: fastboot: Move weak overrides to board files
Overriding fastboot_set_reboot_flag() in arch/arm/mach-omap2/boot-common.c
leaves it applying all boards that derive from this, not just the ones which
have support for Android bootloader flow. Move the weak function override to
the relevant board files.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-05-30 11:59:21 +02:00
Alex Kiernan
8a65bd6372 fastboot: Rename fb_set_reboot_flag to fastboot_set_reboot_flag
Rename fb_set_reboot_flag to fastboot_set_reboot_flag so it matches
all other fastboot code in the global name space. Fix the guards around
them so that they're dependent on FASTBOOT, not just USB_FUNCTION_FASTBOOT.

Move the weak implementation of fastboot_set_reboot_flag to fb_common.c
so we can call it from non-USB fastboot code.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-05-30 11:59:21 +02:00
Alex Kiernan
42d8dd4424 fastboot: Correct dependencies in FASTBOOT_FLASH
Ensure that when selecting FASTBOOT_FLASH you end up with a buildable
configuration. Prior to this you could select NAND without MTDPARTS
and end up with an image which (surprisingly) excluded NAND.

Also fix dependencies on FASTBOOT_GPT_NAME/FASTBOOT_MBR_NAME which require
you have EFI_PARTITION/DOS_PARTITION enabled.

Delete redundant FASTBOOT_FLASH_NAND_DEV from Kconfig - it was only ever
used as a guard and the value was ignored in all cases, we're using
FASTBOOT_FLASH_NAND as the guard now.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2018-05-30 11:59:21 +02:00
Praneeth Bajjuri
cd30f3fc9e arm: dra76: fastboot: extend cpu type for getvar command
'commit dda0bd674481 ("arm: dra762: Add support for device package identification")'
introduces ABZ and ACD package identification.

This patch is to extend usage of "fastboot getvar cpu" for
DRA76x ABZ and ACD devices.

Helps in fixing the boot warning.

Warning: fastboot.cpu: unknown CPU rev: 123863298
on
CPU  : DRA762-GP ES1.0 ABZ package
Model: TI AM5748 IDK
Board: AM574x IDK REV 1.0A

Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-05-08 09:07:37 -04:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Lokesh Vutla
7ce85318cf arm: mach-omap2: cache: Explicitly enable I cache
omap-common cache enabling sequence relies on cpu_init_cp15()
(inside start.S) for enabling I-caches. But cpu_init_cp15()
can be skipped if CONFIG_SKIP_LOWLEVEL_INIT is defined. So
enable I-caches if not enabled already.

Debugged-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-05-06 13:35:40 -04:00
Alex Kiernan
117a0e02be spl: ti: Avoid preloader_console_init if !CONFIG_SPL_SERIAL_SUPPORT
If CONFIG_SPL_SERIAL_SUPPORT is disabled then the build fails because
serial_init is undefined. Guard preloader_console_init() appropriately
to fix this.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-04-28 18:32:22 -04:00
Tom Rini
d024236e5a Remove unnecessary instances of DECLARE_GLOBAL_DATA_PTR
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:48 -04:00
Alex Kiernan
9925f1dbc3 net: Move enetaddr env access code to env config instead of net config
In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.

This fixes failures such as:

  board/ti/am335x/built-in.o: In function `board_late_init':
  board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
  u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'

which caters for use cases such as:

commit f411b5cca4 ("board: am335x: Always set eth/eth1addr environment
variable")

when Ethernet is required in Linux, but not U-Boot.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-04-08 23:00:58 -04:00
Russ Dill
025a0d40e1 ARM: am33xx: Inhibit re-initialization of DDR during RTC-only
This inhibits the re-inititialization of DDR during an RTC-only resume. If
this is not done, an L3 NOC error is produced as the DDR gets accessed
before the re-init has time to complete. Tested on AM437x GP EVM.

Signed-off-by: Russ Dill <Russ.Dill@ti.com>
[j-keerthy@ti.com Ported to Latest Master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
2018-04-06 17:04:33 -04:00
Dave Gerlach
e18945ad22 am43xx: Do not allow EMIF to control DDR_RESET in rtconly config
Prevent EMIF control of DDR_RESET line on DDR3 am43xx platforms for
am43xx_evm_rtconly_config. Without this DDR is unstable and can become
corrupted after multiple iterations of RTC+DDR mode.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[j-keerthy@ti.com Ported to latest master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-04-06 17:04:33 -04:00
Tero Kristo
7619badb9c ARM: AM43xx: Add support for RTC only + DDR in self-refresh mode
Kernel stores information to the RTC_SCRATCH0 and RTC_SCRATCH1 registers
for wakeup from RTC-only mode with DDR in self-refresh. Parse these
registers during SPL boot and jump to the kernel resume vector if the
device is waking up from RTC-only modewith DDR in Self-refresh.

The RTC scratch register layout used is:

SCRATCH0 : bits00-31 : kernel resume address
SCRATCH1 : bits00-15 : RTC magic value used to detect valid config
SCRATCH1 : bits16-31 : board type information populated by bootloader

During the normal boot path the SCRATCH1 : bits16-31 are updated with
the eeprom read board type data. In the rtc_only boot path the rtc
scratchpad register is read and the board type is determined and
correspondingly ddr dpll parameters are set. This is done so as to avoid
costly i2c read to eeprom.

RTC-only +DRR in self-refresh mode support is currently only enabled for
am43xx_evm_rtconly_config.
This is not to be used with epos evm builds.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
[j-keerthy@ti.com Rebased to latest u-boot master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-04-06 17:04:33 -04:00
Tom Rini
6f6b7cfa89 Convert all of CONFIG_CONS_INDEX to Kconfig
This converts the following to Kconfig:
   CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them.  They're also sometimes used for things not
directly inside of the serial driver.  First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it.  Next, consolidate all of these into the single entry in
drivers/serial/Kconfig.  Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-16 10:28:52 -04:00
Sam Protsenko
7a390c0e25 omap: Fix AM335x build with enabled fastboot flash
When enabling CONFIG_FASTBOOT_FLASH in am335x_boneblack_defconfig, next
build errors and warnings occur:

    arch/arm/mach-omap2/utils.c: In function ‘omap_set_fastboot_cpu’:
    arch/arm/mach-omap2/utils.c:26:16: warning: implicit declaration of
              function ‘omap_revision’ [-Wimplicit-function-declaration]
              u32 cpu_rev = omap_revision();
                            ^~~~~~~~~~~~~
    arch/arm/mach-omap2/utils.c:29:7: error: ‘DRA762_ES1_0’ undeclared
              (first use in this function)

Include asm/omap_common.h explicitly to avoid those.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-03-13 21:59:29 -04:00
Masahiro Yamada
b08c8c4870 libfdt: move headers to <linux/libfdt.h> and <linux/libfdt_env.h>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.

This commit moves the header code:
  include/libfdt.h         -> include/linux/libfdt.h
  include/libfdt_env.h     -> include/linux/libfdt_env.h

and replaces include directives:
  #include <libfdt.h>      -> #include <linux/libfdt.h>
  #include <libfdt_env.h>  -> #include <linux/libfdt_env.h>

Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-05 10:16:28 -05:00
Faiz Abbas
b432b1ebdf spl: Kconfig: Rename SPL_USBETH_SUPPORT to SPL_USB_ETHER to match with the U-boot CONFIG
Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER.

This enables users to block text using CONFIG_IS_ENABLED() instead
of resorting to #if ladders with SPL and non-SPL cases.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2018-03-05 10:06:05 -05:00
Andrew F. Davis
5fbed8f2c6 ARM: Kconfig: Move TI_SECURE_DEVICE to a common area
TI_SECURE_DEVICE is used by both OMAP2+ and Keystone2 family devices,
and so when ARCH_OMAP2PLUS was used to gate off the OMAP2+ Kconfig
Keystone2 family devices lost this config option.

Move this option out of mach-omap2 Kconfig to a spot accessible by both
families. We picked arch/arm/Kconfig over the TI specific board/ti/
location as this option is not specific to our boards but rather our
architecture.

Plus at some point this option can be changed to just
SECURE_DEVICE, as having secure parts is not exclusive to TI and
so other vendors can interpret this option as needed by their device
configurations.

Fixes: a93fbf4a78 ("ARM: omap2+: rename config to ARCH_OMAP2PLUS and consolidate Kconfig")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-02-23 10:21:41 -05:00
Kishon Vijay Abraham I
2022270c7d ARM: OMAP5: set mmc clock frequency to 192MHz
Now that omap_hsmmc has support for hs200 mode, change the clock
frequency to 192MHz. Also change the REFERENCE CLOCK frequency to
192MHz based on which the internal mmc clock divider is calculated.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19 16:58:55 +09:00
Kishon Vijay Abraham I
6a27333ba3 ARM: OMAP5/DRA7: Enable iodelay recalibration to be done from uboot
Add a new API to perform iodelay recalibration without isolate
io to be used in uboot.

The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met. The MMC driver can use the new API to
set the IO delay values depending on the MMC mode.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19 16:58:55 +09:00
Bin Meng
d679a529a4 arm: omap2: Fix compiler warning
Fix build warning in arch/arm/mach-omap2/emif-common.c and
arch/arm/mach-omap2/omap4/emif.c with gcc 7.3.0:

  warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-02-13 20:34:07 -05:00
Faiz Abbas
b442e16b87 am33xx: board: Call spl_early_init() to support sdram_init()
With driver model enabled in SPL, sdram_init() requires device tree
and malloc to be initialized.
Therefore call spl_early_init() in early_system_init().

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-28 12:27:33 -05:00
Felix Brack
85ab0452fe arm: add support for PDU001
This patch adds support for the PDU001 board.

Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-28 12:27:32 -05:00
Andrew F. Davis
60013a2cf6 arm: mach-omap2: Pass args to secure ROM in SRAM in SPL
When in early SPL we make some secure ROM calls that can effect
DRAM, due to this it is more stable to store the args for these
calls in SRAM, but uninitialized and zero'd globals are placed
in BSS, located in DRAM. Force our args into the data section
which is in SRAM during SPL.

Signed-off-by: Andrew F. Davis <afd@ti.com>
2018-01-28 09:39:05 -05:00
Andrew F. Davis
6b3d4f3def arm: mach-omap2: Remove secure certificate name printing
The signing certificate name is always 15 chars long, but need not be
null terminated. One solution is then to use printf precision modifiers
to only print this many chars ("%.15s"), but tiny printf does not support
this, so lets just drop printing the cert name for now.

Signed-off-by: Andrew F. Davis <afd@ti.com>
2018-01-19 15:49:30 -05:00
Madan Srinivas
fbd23b9b94 arm: am33xx: security: Fix size calculation on header
Fix the size calculation in the verify boot. The header size
should be subtracted from the image size, not be assigned to
the image size.

Fixes: 0830d72bb9 ("arm: am33xx: security: adds auth support for encrypted images")
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19 15:49:30 -05:00
Lokesh Vutla
1f126897d8 board: ti: am57xx: Enable CMD_DDR3
Enable CMD_DDR3 on all am57xx based platforms.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19 15:49:27 -05:00
Lokesh Vutla
941f2fcc5b arm: dra762: Add support for device package identification
DRA762 comes in two packages:
- ABZ: Pin compatible package with DRA742 with DDR@1333MHz
- ACD: High performance(OPP_PLUS) package with new IPs

Both the above packages uses the same IDCODE hence needs to
differentiate using package information in DIE_ID_2.
Add support for the same. Also update clock, ddr, emif information.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19 15:49:26 -05:00
Lokesh Vutla
650fda93c8 arm: emif-common: Add suppport for enabling ECC
For data integrity, the EMIF1 supports ECC on the data
written or read from the SDRAM. Add support for enabling
ECC support in EMIF1.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
2018-01-19 15:49:25 -05:00
Lokesh Vutla
e18cd3d796 arm: emif-common: Add ecc specific emif registers
This is a slight difference in emif_ddr_phy_status register offsets for
DRA7xx EMIF and older versions. And ecc registers are available only
in DRA7xx EMIC. Add support for this difference and ecc registers.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19 15:49:25 -05:00
Lokesh Vutla
9b88a4bda2 arm: am33xx: Avoid writing into reserved DPLL divider
DPLL DRR doesn't have an M4 divider. But the clock driver is trying
to configure M4 divider as 4(writing into a reserved register).
Fixing it by making M4 divider as -1.

Reported-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-01-19 15:49:24 -05:00
Hannes Schmelzer
3215192922 mach-omap2: add AM335x Display PLL register definition
Adds the register definition of the Display DPLL

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
2018-01-11 15:16:34 +01:00
Derald D. Woods
c2900f595e ARM: dts: omap3-evm: Enable DM and devicetree for TMDSEVM{3530, 3730}
This commit updates the configuration files needed to support OF_CONTROL
on the OMAP3 EVM baseboard.

Additionally:
- CONFIG_SYS_THUMB_BUILD is enabled
- CONFIG_SPL_ENV_SUPPORT is enabled

Tested using GCC 7.2.0 [--with-float=hard --with-mode=thumb].

Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2018-01-01 09:04:19 -05:00
Tom Rini
0c4d24823e Merge git://git.denx.de/u-boot-uniphier 2017-12-04 10:24:35 -05:00
Masahiro Yamada
6ae3900a86 mtd: nand: Rename nand.h into rawnand.h
This header was renamed to rawnand.h in Linux.

The following is the corresponding commit in Linux.

  commit d4092d76a4a4e57b65910899948a83cc8646c5a5
  Author: Boris Brezillon <boris.brezillon@free-electrons.com>
  Date:   Fri Aug 4 17:29:10 2017 +0200

      mtd: nand: Rename nand.h into rawnand.h

      We are planning to share more code between different NAND based
      devices (SPI NAND, OneNAND and raw NANDs), but before doing that
      we need to move the existing include/linux/mtd/nand.h file into
      include/linux/mtd/rawnand.h so we can later create a nand.h header
      containing all common structure and function prototypes.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-12-04 22:00:00 +09:00
Peter Robinson
b59670f2bd omap2: set the ethaddr as well as the usbethaddr env var to ensure static MAC
The kernel gets the ethernet MAC from the ethaddr variable, the omap boards for
devices with USB based eth adapters just set the usbethaddr which doesn't appear
to get passed to the kernel. The same Raspberry Pi code sets both ethaddr and
usbethaddr so lets do that so linux (tested 4.13 and 4.14) get a static rather
than a random MAC address, while not regressing users of usbethaddr.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
2017-12-02 18:32:58 -05:00
Faiz Abbas
16fa2eb951 ARM: dra7: Kconfig: Add thermal configs for dra7xx and am57xx
Configure thermal configs to remain set by default for dra7xx and am57xx
devices.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-21 08:03:39 -05:00
Felix Brack
c07bf9bea7 am33xx: Add a function to query MPU voltage in uV
For the DM TPS65910 driver I'm working on, querying the MPU voltage
should return a value in uV. This value can then be used by the
regulator's standard function set_value to set the MPU voltage.

Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-11-17 07:43:32 -05:00
Adam Ford
0a9ef45158 Convert CONFIG_NAND_OMAP_GPMC et al and CONFIG_NAND_MXC to Kconfig
This converts the following to Kconfig:
   CONFIG_NAND_MXC
   CONFIG_NAND_OMAP_GPMC
   CONFIG_NAND_OMAP_GPMC_PREFETCH
   CONFIG_NAND_OMAP_ELM
   CONFIG_SPL_NAND_AM33XX_BCH
   CONFIG_SPL_NAND_SIMPLE
   CONFIG_SYS_NAND_BUSWIDTH_16BIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues,
        add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-20 16:44:07 -04:00
Praneeth Bajjuri
9b46ce8cfc arm: dra76: fastboot: extend cpu type for getvar command
'commit fa24eca1f2 ("omap: Add routine for setting fastboot variables")'
adds initial support and usage of "fastboot getvar" command
for DRA75x and DRA72x devices.

and
'commit 0f9e6aee9d ("arm: dra76: Add support for ES1.0 detection")'
adds initial dra76 device definition

This patch is to extend usage of "fastboot getvar" for DRA76 device.

Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-10-16 09:43:34 -04:00
Vishal Mahaveer
b6df93598c omap-common: fastboot: extend cpu type for DRA71x rev 2.1
DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Extend support for this
revision in "getvar cpu" command.

Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
[praneeth@ti.com: rebase to u-boot master]
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-10-16 09:43:34 -04:00
Sam Protsenko
268577669a omap: Fix warning when looking for userdata part
When eMMC was formattaed for Linux partition table, "userdata" partition
is missing. In this case, part_get_info_by_name() iterates over all
registered drivers (which are PART_TYPE_EFI, PART_TYPE_DOS and
PART_TYPE_ISO). And when it comes to PART_TYPE_ISO (which has empty
partition table), we can see next warning in U-Boot output:

    ** First descriptor is NOT a primary desc on 1:1 **

This patch switches to part_get_info_by_name_type() API in order to
check only EFI partitions for "userdata" partitions. This eliminates
mentioned warning.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-06 11:28:17 -04:00
Sam Protsenko
19d141a0f9 omap: Omit fastboot.userdata_size related errors
When using regular $partitions variable (for Linux boot), we can see
some unwanted messages:

> ERROR: cannot find partition: 'userdata'

> at arch/arm/mach-omap2/utils.c:96/omap_mmc_get_part_size()
> Warning: fastboot.userdata_size: unable to calc

Let's remove those, as missing 'userdata' partition is correct behavior
for Linux partition, and we don't want to see some Android-related
messages in this case.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
2017-10-06 11:28:16 -04:00
Jean-Jacques Hiblot
a4d72869f8 omap: detect board before spl_early_init()
In order to be able to select the right DTB, we need to have identified the
board before spl_early_init() is called.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-06 11:27:40 -04:00
Masahiro Yamada
9b643e312d treewide: replace with error() with pr_err()
U-Boot widely uses error() as a bit noisier variant of printf().

This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:

  # define __compiletime_error(message) __attribute__((error(message)))

This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux.  (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)

Let's convert error() into now treewide-available pr_err().

Done with the help of Coccinelle, excluing tools/ directory.

The semantic patch I used is as follows:

// <smpl>
@@@@
-error
+pr_err
 (...)
// </smpl>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-04 11:59:44 -04:00
Madan Srinivas
0830d72bb9 arm: am33xx: security: adds auth support for encrypted images
This patch adds support for authentication of both plain
text and encrypted binaries. A new SECDEV package is needed
to enable encryption of binaries by default for AM3x.

The ROM authentication API detects encrypted images at
runtime and automatically decrypts the image if the
signature verification passes.

Addition of encryption on AM3x results in a change in the
image format. On AM4x, AM5x and, on AM3x devices signing
clear test images, the signature is appended to the end of the
binary.

On AM3x, when the SECDEV package is used to create signed
and encrypted images, the signature is added as a header
to the start of the binary. So the binary size calculation
has been updated to reflect this change.

The signing tools and encrypted image format for AM3x
cannot be changed to behave like AM4x and AM5x to
maintain backward compatibility with older Sitara
M-Shield releases.

Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
2017-09-29 14:07:55 -04:00