This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the ftgmac100 driver to support NC-SI instead of an mdio phy
where available. This is a common setup for Aspeed AST2x00 platforms.
NC-SI mode is determined from the device-tree if either phy-mode sets it
or the use-ncsi property exists. If set then normal mdio setup is
skipped in favour of the NC-SI phy.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Previously we'd been using a device name retrieved via
ftgmac100_data->phydev, but the mdio read/write functions may be
called before that member is initialized in ftgmac100_phy_init(),
leading to a NULL pointer dereference while printing the error message
issued if the mdio access fails. We can instead use bus->name, which
is already available at that point.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 538e75d3fc ("net: ftgmac100: add MDIO bus and phylib support")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Rename constant PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA to make
it compatible with Linux' naming.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Add helpers ofnode_read_phy_mode() and dev_read_phy_mode() to parse the
"phy-mode" / "phy-connection-type" property. Add corresponding UT test.
Use them treewide.
This allows us to inline the phy_get_interface_by_name() into
ofnode_read_phy_mode(), since the former is not used anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support of the MAC controller of Aspeed AST2600 SOC. The MAC
controller is the same with AST2500, except it has stand-alone MDIO
hardware block.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add support for DM_MDIO to connect to PHY. For the systems that have a
stand-alone MDIO hardware block, enable CONFIG_DM_MDIO to use driver
model for MDIO devices.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
ftgmac100 driver is using hard-coded PHY interface address of zero.
Each board can have different PHY interface address (phy_addr).
This commit modifies the driver to make use of board specific address
by leveraging CONFIG_PHY_ADDR.
Signed-off-by: Thirupathaiah Annapureddy <thiruan@linux.microsoft.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: e766849713 ("net: ftgmac100: convert the RX/TX descriptor arrays")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Faraday ftgmac100 MAC controllers as found on the Aspeed SoCs have
some slight differences in the HW interface (End-Of-Rx/Tx-Ring bits).
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use simple arrays under the device priv structure to hold the RX and
TX descriptors and handle memory coherency by invalidating or flushing
the d-cache when required.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Implement the MDIO bus read/write functions using the readl_poll_timeout()
routine, initialize the bus and scan for the PHY. RGMII and RMII mode
are supported.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The driver is based on the previous one and the code is only adapted
to fit the driver model. The support for the Faraday ftgmac100
controller is the same with MAC and MDIO bus support for RGMII/RMII
modes.
Configuration is updated to enable compile again. At this stage, the
driver compiles but is not yet functional.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.
Simple uses of sprintf are also converted to use strcpy.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the naming convention used in the network stack functions and
variables that Ethernet drivers use to interact with it.
This cleans up the temporary hacks that were added to this interface
along with the DM support.
This patch has a few remaining checkpatch.pl failures that would be out
of the scope of this patch to fix (drivers that are in gross violation
of checkpatch.pl).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
These are all the files which use the API incorrectly but did not get
built using MAKEALL -a powerpc|arm. I have no compiler for them, but
the remaining issues should be far less than without this patch.
Any outstanding issues are left to the maintainers of boards that use
these drivers.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
There are several mdelay() definitions in the driver and
board code. Remove them all and provide a common mdelay()
in lib/time.c.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This patch move the reset function from initialization to
driver register procedure.
Some embedded system supports wake on lan nowadays. On this kind of system,
the ftgmac100 will be still supplied power after the system has been
shut-down by Linux. Hence the register used by linux won't be clear
when the system has been powered-off.
The origin ftgmac100 driver in u-boot will only register
driver and functions to network stack and won't reset the ftgmac100
hardware if the network won't be used during boot-up.
This will lead ftgmac100 continue receiving packets and then might corrupt
linux kernel when booting up.
So we reorder the hardware reset function earlier to force the hardware
to be reset whether it will be used or not.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
