Commit graph

1150 commits

Author SHA1 Message Date
Siva Durga Prasad Paladugu
a5a387a421 spi: zynq_qspi: Read only one byte at a time from txbuf
Read only one byte at a time from txbuf as txbuf may not be
aligned and accessing more than a byte at a time may cause
alignment issues. This fixes the issue of data abort exception
while writing to flash device.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220131052240.23403-3-ashok.reddy.soma@xilinx.com
2022-02-04 13:20:12 +01:00
Siva Durga Prasad Paladugu
255537b5ad spi: zynq_qspi: Typecast rxbuf properly
This patch typecasts and accesses rx buf properly as
an unaligned rxbuf, typecasting with u16 and accessing
it causes data abort exception and this patch fixes it.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220131052240.23403-2-ashok.reddy.soma@xilinx.com
2022-02-04 13:20:10 +01:00
Daniel Wagenknecht
b106a14e2f sunxi: SPI: fix pinmuxing for Allwinner H6 SoCs
The driver for SPI0 on Allwinner H6 SoCs did not use the correct define
SUN50I_GPC_SPI0 for the pin function, but one for a different Allwinner
SoC series.

Fix the conditionals to use the correct define for H6 SoCs. This matches
the conditional logic in the SPL spi driver.

Tested by probing the spi-flash on a pine64_h64-model-b board with
adapted device-tree (disable mmc2, enable spi0).

Signed-off-by: Daniel Wagenknecht <dwagenk@mailbox.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-01-30 01:03:37 +00:00
Heinrich Schuchardt
185f812c41 doc: replace @return by Return:
Sphinx expects Return: and not @return to indicate a return value.

find . -name '*.c' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;

find . -name '*.h' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
2022-01-19 18:11:34 +01:00
Stefan Mätje
a6e562fe36 Fix wrong QSPI clock calculation for AM4372
On AM4372 the SPI_GCLK input gets its clock from the PRCM module which
divides the PER_CLKOUTM2 frequency (192MHz) by a fixed factor of 4.
See AM437x Reference Manual in section 27 QSPI >> 27.2 Integration.

The QSPI_FCLK therefore needs to take this factor into account and
becomes (192000000 / 4).

Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
2022-01-16 08:31:03 -05:00
Tom Rini
0dadad6d7c - disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
 - add changes to support VIM3/L android boot by using meson64_android.h config
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAmHYV8MACgkQd9zb2sjI
 SdELkA/+LjyjJB1KI6/KLLg43zyFeeZX/SjQd5BUIx6EfaCgyTkuq2lzQnErGmbi
 HoyMoNLpBxLIL27/5TXPzmKYAeOfKPxA/sXTTtx/l7PG8ncSZIoU0+utqjycdUsK
 tSi7EdFzk7/kDDRkqqA7q9nxsPn/7GQNh/ZC9zstMXKaTO/TEb/sZWCMcvQ0MNoB
 ynZKOCg5t60UkIYIRwZwC/OS/ssn86dovv/Aa/8D6qpL2AbS5DoCXHuAr8Dnz7fJ
 q4rV7oLh7a+WHe/qC7R6ylYFIVVqY5JaIgbLDwuvk1z9o7txchMMQnGgllZ35sN9
 LECD2iSDGjhPaHuGCvQwl3TWtIpvtdcP4sQTyJhsXNPxCG6HHvRz7xY4erUohR1I
 LIddwCCHeCrBiaamXNbCzph2+JhfPSQ5ETCL9M6iBMxNUPunlCxjfjDzlT/pg11p
 EO9PIPjRMR9QhxKtd3gZpyAqPuMBEmIwhDtHI6dL3DNOOsF44ObE4swnzS6qXIDn
 jRZzFCC2f/Vyg11YnzFtV3A5eWwJahGDWAGAnnlg6Y8GCLlLmDJitcgA/rWSALko
 T5fC8L8IFUx2RnHczyitJ/wqJl9FqOAnIaoB3Trpwp8gFQ15dQjbvoXldQnAjSS2
 9bns3zOrx79EF4lbHhwNE9UDLm6OjK5vR3h4bGJvyZBmasVsA90=
 =dLEg
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next

- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
2022-01-09 07:56:31 -05:00
Tom Rini
b9c9ce8a40 First set of u-boot-at91 features for the 2022.04 cycle
-----BEGIN PGP SIGNATURE-----
 
 iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmG8PNIcHGV1Z2VuLmhy
 aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyN4NCACbdi5EFjoNkGhCWLIX
 SobXNcBGaL9Zpr5qZq77uFqFeFPeiAClk9X+TcSHhBTSWPugzNCdXEdENEGdiiOR
 Yxe/QvBL7ZsKkhGBw5W8sb81NBPlpnVY7DWufjYvWq7S3C3bIDahQpCeWHKXDO0H
 ZzIX1413kfHRKsAIT+IbufmC1dcWY8SWQEArSkL2KhTQyHnLVGAaholgEGXoKMoC
 0ACXO+uhqaAY0/1eWvvYjcfotlz881ROajSRITh+Gu0UuHyRr2Fvj7jZvF5E4Q4f
 Cu8iciDsimYSDGLZsOJjPIDTfsx9jbA8IcYIAMxOLW8OYbIL6QAUKsJ2LLKao1q5
 SYXP
 =YXsB
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-at91-2022.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next

First set of u-boot-at91 features for the 2022.04 cycle:

This feature set includes : support for the new QSPI hardware on
sama7g5, small fixes on sam9x60 and sama7g5, some additions of commands
and PIO controller on sam9x60/sam9x60ek.
2021-12-17 07:25:34 -05:00
Tudor Ambarus
2fd1b97f33 spi: atmel-quadspi: Add support for SAMA7G5 QSPI
sama7g5 QSPI has:
1/ One Octal Serial Peripheral Interfaces (QSPI0) Supporting Up to
   200 MHz DDR. Octal, TwinQuad, Hyperflash and OctaFlash Protocols Supported
2/ One Quad Serial Peripheral Interfaces (QSPI1) Supporting Up to
   90 MHz DDR/133 MHz SDR

The QSPI controller of SAMA7G5 uses different clock domains, hence extra
synchronization operations must be performed before accessing some
registers. Differentiate between the versions of the IP using has_gclk.
Differentiate between QSPI0 and QSPI1 with has_octal.

Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-12-07 08:55:22 +02:00
Marek Vasut
846d1d9c11 mtd: cqspi: Wait for transfer completion
Wait for the read/write transfer finish bit get actually cleared,
this does not happen immediately on at least SoCFPGA Gen5.

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
2021-12-02 11:10:40 +05:30
Tudor Ambarus
7dc48b41f4 spi: atmel-quadspi: Fix QSPI_RD reg name on verbose debug
It was wrongly set to "MR", fix it.

Fixes: 52e2565bfb ("spi: atmel-quadspi: Add verbose debug facilities to monitor register accesses")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
2021-11-23 09:36:29 +02:00
Tom Rini
2ffa0e87df Xilinx changes for v2022.01-rc3
sdhci:
 - Fix emmc mini case with missing firmware interface
 
 zynqmp:
 - Restore JTAG interface if required
 - Allow overriding board name
 - Add support for DLC21
 - Fix one fallthrought statement description
 - Use config macro instead of name duplication
 - Save multiboot to variable
 
 firmware:
 - Handle ipi_req errors better
 - Use local buffer in case user doesn't need it instead of NULL/0 location
 
 spi:
 - gqsi: Fix write issue at low frequencies
 
 net:
 - gem: Disable broadcasts
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYZPDrwAKCRDKSWXLKUoM
 IS9GAJ93T/uprhLcKWMb+284YMb2caWgOACfZ02nTlzvZKNNXVretJgZaHXqj1M=
 =cwTL
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2022.01-rc3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze

Xilinx changes for v2022.01-rc3

sdhci:
- Fix emmc mini case with missing firmware interface

zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable

firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location

spi:
- gqsi: Fix write issue at low frequencies

net:
- gem: Disable broadcasts
2021-11-16 09:51:04 -05:00
Michael Walle
8c58089287 spi: fsl_dspi: rename num-cs to spi-num-chipselects
The official devicetree bindings specifies spi-num-chipselects as the
name. Use it.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-11-09 17:18:23 +05:30
Michael Walle
765afe7fb3 spi: fsl_dspi: add new compatible fsl, ls1021a-v1.0-dspi
The official ls1028a binding of the driver uses the following as
compatibles:
  compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi";

Add the missing compatible to the driver and update the device tree.
We can use the fallback "fsl,ls1021a-v1.0-dspi", because the endianness
is determined by the little-endian property and not by the compatible
string itself. Further, we won't need and specific details on the DMA
configuration (which is different on the LS1021A). If it's ever needed,
we can later add the more specific "fsl,ls1028a-dspi" compatible to the
driver.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-11-09 17:18:23 +05:30
Ashok Reddy Soma
4f9d25537c spi: zynqmp_gqspi: Fix write issue at low frequencies
With current implementation we are seeing write issues at low frequencies
below 15Mhz. Make below changes to fix the issue.

1. Remove dummy genfifo entry in zynqmp_qspi_chipselect() which was
   incorrectly added in the past

2. Enable and poll for TX_FIFO_Empty after Tx data is filled in FIFO in
   zynqmp_qspi_fill_tx_fifo().

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1634652780-21755-1-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-10-25 10:02:25 +02:00
Tom Rini
355d1e24f6 Merge https://source.denx.de/u-boot/custodians/u-boot-spi
- Fix mtd erase with mtdpart (Marek Behún)
- NXP fspi driver fixes (Kuldeep Singh)
2021-10-23 10:49:28 -04:00
Kuldeep Singh
b9cfd8b091 spi: nxp_fspi: Implement errata workaround for LS1028A
Errata ERR050568 description says that "Flash access by FlexSPI AHB
command may not work with platform frequency equal to 300 MHz" on
LS1028A.

By default, smaller length reads(equal to RX FIFO size) are done by IP
bus and larger length reads using AHB bus. For adding errata workaround,
use IP bus to read entire flash contents and disable AHB path when
platform frequency is 300Mhz.

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-10-23 15:56:47 +05:30
Kuldeep Singh
e8751a9387 spi: nxp-fspi: Add support for IP read only
Add support for disabling AHB bus and read entire flash contents via IP
bus only. Please note, this enables IP bus read using a quirk which can
be enabled directly in device-type data or in existence of an errata
where AHB bus may need to be disabled.

Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2021-10-23 15:56:25 +05:30
Jon Lin
24c627b57a spi: rockchip_sfc: Using read_poll
Using read_poll logic.

Tested-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-10-15 20:57:11 +08:00
Jon Lin
51f29239b7 spi: rockchip_sfc: Implement set_speed logic
Set clock related processing into set_speed logic. And Optimize
printing format.

Tested-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-10-15 20:57:11 +08:00
Tom Rini
776bf6a545 - Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
 - Update stm32-usbphyc node management
 - Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
 - Convert some USB config flags to Kconfig for various boards
 - Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
 - Remove specific CONFIG_STV0991 flags
 - Remove unused CONFIG_USER_LOWLEVEL_INIT flag
 - Add ofdata_to_platdata() callback for stm32_spi driver
 - Update for stm32f7_i2c driver
 - Remove gpio_hog_probe_all() from STM32 MP1 board
 - Fix bind command
 -----BEGIN PGP SIGNATURE-----
 
 iQJQBAABCgA6FiEEXyrViUccKBz9c35Jysd4L3sz/6YFAmFlgsIcHHBhdHJpY2Uu
 Y2hvdGFyZEBmb3NzLnN0LmNvbQAKCRDKx3gvezP/plnND/4q9HSlvddybIPjBHlW
 rXz1ISwj8JZPp7R4MJcB4RiHofYZzjTXx3dDYUif6oQMpCDp64KPfcUDW0kaq8U7
 ZFwJvt59boV1XWlonIXMb3gAkY6gFa5PnYAE/YXEqKvPPvUb7FkT7BWxm4LxCGsj
 mEmboR8u87s6e4ZP03HJsSVa5FnNwJUZU8b+58Vxp10YC0PPf7kpmgCucDhrghvY
 TORlk259KUFoZXz4J4My0VzDdxE05gDqq1m6Xw1CzqcUbGysMvjNEHlxGdYbWD/U
 maamP19DUmKUREmpj3kO/JZvacLJlQP/mdGJ0OWKNbIr/3ha4dYagxDoRodEVo0m
 DYaaVPGvG24G78d5meB2q9wT0aGdTyaqm+XRBQMvMN2LlaGmu9duA1t6yBuyMcFk
 BeA7d0eHMo1ezD9FFZMxwIOAWhJlcYQEAMFhUwkR1B322w0NU4nbl9KRCGuGV2Zp
 ZFQV4BoMvb0NwAdo66xwZ+gSq4Wp1y46VM6x2Mw52v2F4p3teeAqR906TdQVYO8+
 hlYChO9+qK4JO7LPX/5wQ4FIzcq1HnTzTpuOSf28hsemiPMu0OkAQv1J7DohNZix
 wELBA+ZIjGXksmDTPjpXg5CSvVALa/l2G816hp7/XTJ1XRBSz/pzjhp5rwm42zmw
 x7EPnwzpAlQCSqTQ0sgO+fgoRA==
 =S4kl
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm

- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-12 12:01:00 -04:00
Samuel Holland
4d9958b642 sunxi: gpio: Remove name_to_gpio macro
This clarifies which callers must be updated to complete the DM_GPIO
conversion.

The only remaining caller of name_to_gpio in generic code is inside the
!DM_GPIO block in cmd/gpio.c. DM_GPIO is always selected on sunxi, so
that code cannot be reached. And after this commit, there are only two
remaining implementations of name_to_gpio.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Patrice Chotard
81b2445af4 spi: stm32: Add ofdata_to_platdata() callback
Parse DT in ofdata_to_platdata() callback instead of probe().

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-10-08 08:41:47 +02:00
Tom Rini
50c84208ad Merge branch 'next'
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-04 11:28:16 -04:00
Marek Vasut
c2e0363571 mtd: cqspi: Fix division by zero
Both dummy.nbytes and dummy.buswidth may be zero. By not checking
the later, it is possible to trigger division by zero and a crash.
This does happen with tiny SPI NOR framework in SPL. Fix this by
adding the check and returning zero dummy bytes in such a case.

Fixes: 38b0852b0e ("spi: cadence-qspi: Add support for octal DTR flashes")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
[trini: Drop Pratyush's RB as his requested changes weren't made as
        Marek disagreed]
2021-10-04 08:51:14 -04:00
Tom Rini
8ba59608dc arm: Remove zmx25 board and ARCH_MX25
This board has not been converted to CONFIG_DM by the deadline.
Remove it.  As this is the last ARCH_MX25 platform, remove those
references as well.

Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-01 21:08:18 -04:00
Tom Rini
14b38cb0c2 arm: Remove flea3 board
This board has not been converted to CONFIG_DM by the deadline.
Remove it.  As this is the last mx35 platform, remove that support as
well.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2021-10-01 12:08:19 -04:00
Wolfgang Denk
0cf207ec01 WS cleanup: remove SPACE(s) followed by TAB
Signed-off-by: Wolfgang Denk <wd@denx.de>
2021-09-30 09:08:16 -04:00
Simon Glass
f0ab8f9fbe clk: Rename clk_get_by_driver_info()
This is actually a misnomer now, since the phandle info may contain
a driver_info index or a udevice index. Rename it to use the word
'phandle', which seems more accurate. Add a comment while we are here.

Also add a test for this function.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-09-25 09:46:15 -06:00
Simon Glass
dcfc42b12f treewide: Try to avoid the preprocessor with OF_REAL
Convert some of these occurences to C code, where it is easy to do. This
should help encourage this approach to be used in new code.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-09-25 09:46:15 -06:00
Simon Glass
9539738509 treewide: Use OF_REAL instead of !OF_PLATDATA
Now that we have a 'positive' Kconfig option, use this instead of the
negative one, which is harder to understand.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-09-25 09:46:15 -06:00
Simon Glass
414cc15144 treewide: Simply conditions with the new OF_REAL
Use this new Kconfig to simplify the compilation conditions where
appropriate.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-09-25 09:46:15 -06:00
Tom Rini
6674edaabf Prepare v2021.10-rc4
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAmFBKRgACgkQFHw5/5Y0
 tyw/PwwAtGB3rBeYW4rjWuMC5WP1UDTnvZIAok5ImWumWDahjDm8Yq2VCzAe9adw
 EYBjuNmaNl9aQvGVqlVJeIcLku5MLuLQu2za8vhc1R8X9VTPPY+LLTcdOokOmB8y
 8JiaE7fJsb1bZeV+diF9tss3B0IkUrwSJtW1d+qfdz/4UiRvwK5BhnZgzIobDldO
 g1Ldz/xiR2GOAXlUMwDrNAi6qNvmeAqRsQxySVrjltAV2ST7LJnOiHuWvJX6g6VS
 l796Hleh/kULfEW6n+1ZaTNqvVRcJ8xYSOG8w8y9u6HuPBA3JrYH1p1Eo5n7PPDv
 US71Iy/ncweTyfTMEBThWLqjHOQ05sVkWX/r4fj2iJRli+Og53lE1fVJ4ajIx7vz
 Tc76wI43i0I5lr2yTErjUG6EzDDoueqd+c8BwxihNLUK/+QG31xoCEMfC80C25ro
 QhYVFgiPWN0ySUD5M5tbGXODvfNNIDKXpY5oSOTVtemZtDEMpO2zBM1s/K3RV7Ud
 Je9Pj0Cu
 =Me42
 -----END PGP SIGNATURE-----

Merge tag 'v2021.10-rc4' into next

Prepare v2021.10-rc4

Signed-off-by: Tom Rini <trini@konsulko.com>

# gpg: Signature made Tue 14 Sep 2021 06:58:32 PM EDT
# gpg:                using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C
# gpg: Good signature from "Thomas Rini <trini@konsulko.com>" [ultimate]

# Conflicts:
#	board/Arcturus/ucp1020/spl.c
#	cmd/mvebu/Kconfig
#	common/Kconfig.boot
#	common/image-fit.c
#	configs/UCP1020_defconfig
#	configs/sifive_unmatched_defconfig
#	drivers/pci/Kconfig
#	include/configs/UCP1020.h
#	include/configs/sifive-unmatched.h
#	lib/Makefile
#	scripts/config_whitelist.txt
2021-09-16 10:29:40 -04:00
Simon Glass
3232bdf0b3 pci: Drop DM_PCI
This option has not effect now. Drop it, using PCI instead where needed.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-09-13 18:23:13 -04:00
Ashok Reddy Soma
020b353be9 spi: zynqmp_gqspi: Fix dma alignment issue
DMA is aligned to ARCH_DMA_MINALIGN(64 bytes), but as per spec, alignment
required is 4bytes only. Change DMA alignment from ARCH_DMA_MINALIGN to
GQSPI_DMA_ALIGN. Remove alignment of data length in non-exponential case.

Some minor improvements in the initialization to initialize gen_fifo
threshold and disable qspi controller while setting config register.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-09-03 09:15:01 +02:00
Ashok Reddy Soma
72022a5b2e spi: zynqmp_gqspi: Switch genfifo start to manual mode
Current implementation uses auto mode for starting generic FIFO.
The recommendation from IP designers is to use manual mode, hence
change to manual start mode.

In fill genfifo first write to genfio and then trigger manual start.

Also enable and check for genfifo empty interrupt status in place of
genfifo not full interrupt.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-09-03 09:14:58 +02:00
Tom Rini
b166f0449c spi: altera_spi: Do not abuse CONFIG namespace
The value CONFIG_ALTERA_SPI_IDLE_VAL is never re-defined by a board.
Rename this to ALTERA_SPI_IDLE_VAL.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2021-08-30 14:13:28 -04:00
Michael Walle
364174b2d3 spi: nxp_fspi: Ensure width is respected in spi-mem operations
Import linux commit 007773e16a6f ("spi: nxp-fspi: Ensure width is
respected in spi-mem operations") to fix SPI access on boards which
don't have all SPI I/O lines connected to the flash.

Since commit 71025f013c ("mtd: spi-nor-core: Rework hwcaps selection")
u-boot figures out the capabilities by looking at spi_mem_supports_op().
The FlexSPI driver doesn't take the board layout into account. Fix that.

Fixes: 383fded70c ("spi: nxp_fspi: new driver for the FlexSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-08-18 15:55:15 +05:30
Chris Morgan
3fb08a2138 spi: rockchip_sfc: add support for Rockchip SFC
This patch adds support for the Rockchip serial flash controller
found on the PX30 SoC. It should work for versions 3-5 of the SFC
IP, however I am only able to test it on v3.

This is adapted from the WIP SPI-MEM driver for the SFC on mainline
Linux. Note that the main difference between this and earlier versions
of the driver is that this one does not support DMA. In testing
the performance difference (performing a dual mode read on a 128Mb
chip) is negligible. DMA, if used, must also be disabled in SPL
mode when using A-TF anyway.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-12 09:34:11 +08:00
Tom Rini
a0953b34d9 Merge https://source.denx.de/u-boot/custodians/u-boot-spi
- SPI-NOR fix (Big Meng)
- XMC XM25QH64C flash (Reto Schneider)
2021-08-03 14:06:41 -04:00
Bin Meng
cb42425aa1 spi: spi-mem-nodm: Fix read data size issue
When slave drivers don't set the max_read_size, the spi-mem should
directly use data.nbytes and not limit to any size. But current
logic will limit to the max_write_size.

This commit mirrors the same changes in the dm version done in
commit 535b1fdb8e ("spi: spi-mem: Fix read data size issue").

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-08-03 11:50:37 +05:30
Bin Meng
4dc8279758 spi: ich: Limit slave->max_read_size
Since commit 43c145b8b3 ("spi: ich: Correct max-size bug in ich_spi_adjust_size()")
(in v2020.04-rc1), SPI flash read no longer works with ICH SPI controller
in software sequencer mode.

ICH controller can only transfer a small number of bytes at once.
Before commit 43c145b8b3, the logic happens to make sure data.nbytes
is limited to slave->max_write_size but after commit 43c145b8b3
data.nbytes is no longer limited because slave->max_read_size is not
initialized with a valid number.

Fixes: 43c145b8b3 ("spi: ich: Correct max-size bug in ich_spi_adjust_size()")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-08-02 15:11:40 +08:00
Tom Rini
d5dbc661c3 i.MX
----
 
 - mx7ulp : fix  WDOG
 - imx8 : Phytec
 - USB3 support for i.MX8
 
 CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/8277
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCYPLjyA8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76aBtgCfUI2SbFwh7oydllrwb0lEvWegfNcAn1JpR3Zn
 H41xrXQqCBedYKxvuUUL
 =5wvR
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20210717' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

i.MX
----

- mx7ulp : fix  WDOG
- imx8 : Phytec
- USB3 support for i.MX8

CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/8277
2021-07-17 10:52:21 -04:00
Simon Glass
f784361b2a spi: ich: Don't require the PCH
When booting from coreboot we may not have a PCH driver available. The
SPI driver can operate without the PCH but currently complains in this
case. Update it to continue to work normally. The only missing feature
is memory-mapping of SPI-flash contents, which is not essential.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-07-15 19:49:52 +08:00
Stefano Babic
375d7e9298 spi: mxc_spi: fix warnings if CLK_ENABLED not set
Following warnings (unused variables) are raised:

drivers/spi/mxc_spi.c: In function 'mxc_spi_probe':
drivers/spi/mxc_spi.c:595:14: error: unused variable 'blob' [-Werror=unused-variable]
595 |  const void *blob = gd->fdt_blob;
    |              ^~~~
drivers/spi/mxc_spi.c:594:6: error: unused variable 'node' [-Werror=unused-variable]
594 |  int node = dev_of_offset(bus);

Move the variable declaration inside the code where they are used.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2021-07-10 18:14:54 +02:00
Frieder Schrempf
6b86554865 spi: fsl_qspi: Build driver only if DM_SPI is available
The driver depends on DM_SPI and if it's not available (e. g. in SPL),
then we should not try to build it as this will fail.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
2021-07-10 16:53:34 +02:00
Tom Rini
7e58a3a148 various minor sandbox improvements
-----BEGIN PGP SIGNATURE-----
 
 iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmDkhxURHHNqZ0BjaHJv
 bWl1bS5vcmcACgkQfxc6PpAIreYqMAf+MBQMxpB5+W1k7mkoDKnbuh2oquEKwRkM
 pE8O/Svk6FJDdi3wYS2bMasxa9V2QgTDmih3wVnWBTY6bIJiH130dyWhhS3HuUdY
 E1P0OZIdcGGz+yR5RPCRn+zk+ULLlpgQymVYN/ltj+yQsXekNDwnIu70Gm0odQ9Z
 fjBytQLEU9lzBvQMA4rjBx2V6hVhedEosaoUcf/O9VLNg36p+okv709y6keLi6g8
 oBYe939Iq/K5elPc6WpKeTU/CiOWUg+0nNuimvWKe0laVkbMjRycxL/vMNutaY9S
 PAwtwJTsHxqz6FmLHSQTUM3n2gY14sfHR2eBkKJWIGUw57/tpZ1CnQ==
 =pXw2
 -----END PGP SIGNATURE-----

Merge tag 'dm-pull-6jul21' of https://source.denx.de/u-boot/custodians/u-boot-dm

various minor sandbox improvements
2021-07-07 13:34:42 -04:00
Jassi Brar
971a344285 spi: synquacer: Add HSSPI SPI controller driver for SynQuacer
This is a driver for the HSSPI SPI controller on SynQuacer SoC.
The HSSPI has command sequence mode (memory mapped) and
direct mode (FIFO access). The driver will operate it under
the direct mode. And before booting OS, it switch back to the
command sequence mode since that is compatible with default
EDK2 behavior.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
2021-07-06 14:07:36 -04:00
Patrick Delaunay
b953ec2bca dm: define LOG_CATEGORY for all uclass
Define LOG_CATEGORY for all uclass to allow filtering with
log command.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-07-06 10:38:03 -06:00
Tom Rini
6194b45a83 Merge branch 'next' 2021-07-05 11:20:30 -04:00
Marek Vasut
e2e95e5e25 spi: Update speed/mode on change
The spi_get_bus_and_cs() may be called on the same bus and chipselect
with different frequency or mode. This is valid usecase, but the code
fails to notify the controller of such a configuration change. Call
spi_set_speed_mode() in case bus frequency or bus mode changed to let
the controller update the configuration.

The problem can easily be triggered using the sspi command:
=> sspi 0:0@1000
=> sspi 0:0@2000
Without this patch, both transfers happen at 1000 Hz. With this patch,
the later transfer happens correctly at 2000 Hz.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-06-30 08:06:30 -04:00
Tom Rini
296d5cffdd Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-spi into next
- xSPI Octal DTR support (Pratyush Yadav)
- MXIC SPI driver (Zhengxun)
2021-06-28 18:31:53 -04:00
Tom Rini
6d0453d889 Prepare v2021.07-rc5
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAmDaJXgACgkQFHw5/5Y0
 tyySmwwAkW7GVAv+bXSd+8u1IsScl0QrSCoBdfHpdMcAME3gZmXqxClxskfbYJR/
 3IByQFlsn7j8HruR/49+etk0i0Pc4HNfynTLuAy+77/lh+h3Pnru/VPBhQqR7KW0
 NN5STn91QWLl74vRmx5wmEfSMhg7LTE1US8Rh6UXAd2dAiPd+hUawIR9D0Pq5Gzm
 nn7HvamDYspFUgSYYl8h1RtRQ9VqAFpnnPphpLkvX6323uCQwccXu5pnj1fLfGfj
 iO2Q+bDcwpEdUosox/LM1BdMoaSA+opOjk/e72y9V84+Jk6D+Jn5zQEpF5TJnTyI
 Yi2+NuJWS5xFWk1dnJrbGt0HpWM2oO12dZZ7eYy/FdsPJiWAS0ppRuxHVb868vjD
 ulca7acFPUjGyo3vBw1S0iVmPCBFGHBoyg3QLrUHYbpISeBeoa2w2cDxQl90ahw/
 TgRx+yutKfwkBPfILwDylNOgCGRwvLfroRyMEMiQ3gTSOCBmBX/yMv1k8tb9ZvPZ
 /WVsK6dw
 =F7x1
 -----END PGP SIGNATURE-----

Merge tag 'v2021.07-rc5' into next

Prepare v2021.07-rc5

# gpg: Signature made Mon 28 Jun 2021 03:39:36 PM EDT
# gpg:                using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C
# gpg: Good signature from "Thomas Rini <trini@konsulko.com>" [ultimate]

# Conflicts:
#	configs/am64x_evm_r5_defconfig
2021-06-28 16:22:13 -04:00
Pratyush Yadav
71025f013c mtd: spi-nor-core: Rework hwcaps selection
The spi-mem layer provides a spi_mem_supports_op() function to check
whether a specific operation is supported by the controller or not.
This is much more accurate than the hwcaps selection logic based on
SPI_{RX,TX}_ flags.

Rework the hwcaps selection logic to use spi_mem_supports_op().

To make sure the build doesn't break for boards not using CONFIG_DM_SPI,
add a simple SPI_{RX,TX}_ based hwcaps selection logic in spi-mem-nodm
similar to spi_mem_default_supports_op(). This change is only
compile-tested.

To avoid SPL size problems on the x530 board, the old hwcaps selection
is still kept around. Leaving the code in-place was getting difficult to
read and understand, so the code is restructured to have it all in one
isolated function. As a result of this, the parameter hwcaps to
spi_nor_setup() is no longer needed. Remove it.

Based on the Linux commit c76f5089796a (mtd: spi-nor: Rework hwcaps
selection for the spi-mem case, 2019-08-06)

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 11:59:35 +05:30
Pratyush Yadav
38b0852b0e spi: cadence-qspi: Add support for octal DTR flashes
Set up opcode extension and enable/disable DTR mode based on whether the
command is DTR or not.

xSPI flashes can have a 4-byte dummy address associated with some
commands like the Read Status Register command in octal DTR mode. Since
the flash does not support sending the dummy address, we can not use
automatic write completion polling in DTR mode. Further, no write
completion polling makes it impossible to use DAC mode for DTR writes.
In that mode, the controller does not know beforehand how long a write
will be and so it can de-assert Chip Select (CS#) at any time. Once CS#
is de-assert, the flash will go into burning phase. But since the
controller does not do write completion polling, it does not know when
the flash is busy and might send in writes while the flash is not ready.

So, disable write completion polling and make writes go through indirect
mode for DTR writes and let spi-mem take care of polling the SR.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 11:57:23 +05:30
Pratyush Yadav
a6903aa7ea spi: cadence-qspi: Add a small delay before indirect writes
Once the start bit is toggled it takes a small amount of time before it
is internally synchronized. This means we can't start writing during
that part. So add a small delay to allow the bit to be synchronized.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 11:57:10 +05:30
Pratyush Yadav
bd8c8dcd4d spi: cadence-qspi: Do not calibrate when device tree sets read delay
If the device tree provides a read delay value, use that directly and do
not perform the calibration procedure.

This allows the device tree to over-ride the read delay value in cases
where the read delay value obtained via calibration is incorrect. One
such example is the Cypress Semper flash. It needs a read delay of 4 in
octal DTR mode. But since the calibration procedure is run before the
flash is switched in octal DTR mode, it yields a read delay of 2. A
value of 4 works for both octal DTR and legacy modes.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 11:56:53 +05:30
Pratyush Yadav
5752d6ae8d spi: spi-mem: add spi_mem_dtr_supports_op()
spi_mem_default_supports_op() rejects DTR ops by default to ensure that
the controller drivers that haven't been updated with DTR support
continue to reject them. It also makes sure that controllers that don't
support DTR mode at all (which is most of them at the moment) also
reject them.

This means that controller drivers that want to support DTR mode can't
use spi_mem_default_supports_op(). Driver authors have to roll their own
supports_op() function and mimic the buswidth checks. Or even worse,
driver authors might skip it completely or get it wrong.

Add spi_mem_dtr_supports_op(). It provides a basic sanity check for DTR
ops and performs the buswidth requirement check. Move the logic for
checking buswidth in spi_mem_default_supports_op() to a separate
function so the logic is not repeated twice.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 11:56:06 +05:30
Pratyush Yadav
d15de62301 spi: spi-mem: allow specifying a command's extension
In xSPI mode, flashes expect 2-byte opcodes. The second byte is called
the "command extension". There can be 3 types of extensions in xSPI:
repeat, invert, and hex. When the extension type is "repeat", the same
opcode is sent twice. When it is "invert", the second byte is the
inverse of the opcode. When it is "hex" an additional opcode byte based
is sent with the command whose value can be anything.

So, make opcode a 16-bit value and add a 'nbytes', similar to how
multiple address widths are handled.

All usages of sizeof(op->cmd.opcode) also need to be changed to be
op->cmd.nbytes because that is the actual indicator of opcode size.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 11:55:11 +05:30
Pratyush Yadav
a1eb40b70b spi: spi-mem: allow specifying whether an op is DTR or not
Each phase is given a separate 'dtr' field so mixed protocols like
4S-4D-4D can be supported.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-28 11:53:48 +05:30
Zhengxun
0d7066bce2 spi: Add MXIC controller driver
Add a driver for Macronix SPI controller IP.

This patch referred from linux spi-mxic.c. The difference from the
linux version is described here.

1. To adapt uboot spi framework, modify some functions naming.

2. Remove the incompatible functions of Uboot.

3. Add dummy byte recalculattion function to support dummy buswidth
   not align data buswidth operation.(ex: 1-1-4, 1-1-8)

4. Add Octal mode support.

Signed-off-by: Zhengxun <zhengxunli.mxic@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: fixed file permission, comment line, kconfig]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2021-06-25 20:59:45 +05:30
Daniil Stas
88f7ca03b4 spi: stm32_qspi: Fix short data write operation
TCF flag only means that all data was sent to FIFO. To check if the
data was sent out of FIFO we should also wait for the BUSY flag to be
cleared. Otherwise there is a race condition which can lead to
inability to write short (one byte long) data.

Signed-off-by: Daniil Stas <daniil.stas@posteo.net>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-06-18 08:39:45 +02:00
Ashok Reddy Soma
2ffa653798 spi: zynqmp_gqspi: Fix write issue
Enable manual start in zynqmp_qspi_fill_gen_fifo().
Also enable GQSPI_IXR_GFNFULL_MASK and check for it instead of
GQSPI_IXR_GFEMTY_MASK.

Add dummy write to genfifo register in chipselect.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
2021-06-11 09:24:58 +02:00
Grzegorz Jaszczyk
9c84159ce1 spi: kirkwood: prevent limiting speed to 0
After commit 1fe929ed497bcc8975be8d37383ebafd22b99dd2
("spi: kirkwood: prevent configuring speed exceeding max controller freq")
the spi frequency could be set to 0 on platform where spi-max-frequency
is not defined (e.g. on armada-388-gp). Prevent limiting speed in
mentioned cases.

Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Tested-by: Kostya Porotchkin <kostap@marvell.com>
Reviewed-by: Marcin Wojtas <marcin@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2021-05-16 06:48:45 +02:00
Marcin Wojtas
562f8d5b36 spi: kirkwood: prevent configuring speed exceeding max controller freq
This patch adds a limitation in the kirkwood_spi driver
set_speed hook, which prevents setting too high transfer
speed.

Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Tested-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2021-05-16 06:48:45 +02:00
Ken Ma
037818c544 spi: kirkwood: support extended baud rates
The Armada SoC family implementation of this SPI hardware module has
extended the configuration register to allow for a wider range of SPI
clock rates. Specifically the Serial Baud Rate Pre-selection bits in the
SPI Interface Configuration Register now also use bits 6 and 7 as well.

Modify the baud rate calculation to handle these differences for the
Armada case. Potentially a baud rate can be setup using a number of
different pre-scalar and scalar combinations. This code tries all
possible pre-scalar divisors (8 in total) to try and find the most
accurate set.

Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2021-05-16 06:48:45 +02:00
Dylan Jhong
1412b8d48a atcspi200: Add timeout mechanism in spi_xfer()
Adding timeout mechanism to avoid spi driver from stucking
in the while loop in __atcspi200_spi_xfer().

Signed-off-by: Dylan Jhong <dylan@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
2021-05-05 16:12:14 +08:00
Michal Simek
b00bad9dc8 spi: zynqmp: Remove gd reference
gd is not used in this file that's why doesn't make sense to declare it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-04-29 14:48:31 +02:00
Tom Rini
db8b46120a Xilinx changes for v2021.07
net:
 - Fix gem PCS support
 
 spi:
 - Small trivial fixes
 
 zynq:
 - Enable time/timer commands
 - Update bitmain platform
 - Several DT changes
 
 zynqmp:
 - Update clock driver
 - mini config alignments
 - Add/update psu_init for zcu208/zcu216/zc1275
 - Several DT changes
 - Enable efi debug command (also for Versal)
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYGRy+AAKCRDKSWXLKUoM
 IUN9AKCQHHdbKIciyhucUj5ThwT3CDaUswCeLQkRB1SrM6E8k6KkErWEA+xOxsU=
 =fIEs
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2021.07' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next

Xilinx changes for v2021.07

net:
- Fix gem PCS support

spi:
- Small trivial fixes

zynq:
- Enable time/timer commands
- Update bitmain platform
- Several DT changes

zynqmp:
- Update clock driver
- mini config alignments
- Add/update psu_init for zcu208/zcu216/zc1275
- Several DT changes
- Enable efi debug command (also for Versal)
2021-03-31 09:47:30 -04:00
T Karthik Reddy
d999a7b7b6 spi: xilinx_spi: Trivial fixes in axi qspi driver
Use __func__ instead for function name in debug.
Use Linux style u32 instead of uint32_t.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
T Karthik Reddy
346df7d4fa spi: spi-uclass: Add support to manually relocate spi memory ops
Add spi memory operations to relocate manually when
CONFIG_NEEDS_MANUAL_RELOC is enabled.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
2021-03-27 16:26:48 +13:00
Patrice Chotard
e48ec51b43 spi: stm32_qspi: Add WATCHDOG_RESET in _stm32_qspi_read_fifo()
In case of reading large area and memory-map mode is misconfigured
(memory-map size declared lower than the real size of the memory chip)
watchdog can be triggered.

Add WATCHDOG_RESET() in _stm32_qspi_read_fifo to fix it.

Issue reproduced with stm32mp157c-ev1 board and memory map size set to
1, with following command:
sf read 0xC0000000 0 0x4000000

Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-03-11 16:59:16 +01:00
Adam Ford
90d76f812b spi: nxp_fspi: Fix error reporting
On the i.MX8M Mini, ret = clk_set_rate() sets ret to the value of the
rate the clock was able to set.  When checking for errors, it only
checks that it is not NULL.  Since positive numbers are not errors,
only check for negative numbers when handling errors.

Fixes: 383fded70c ("spi: nxp_fspi: new driver for the FlexSPI controller")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2021-02-26 15:09:38 +05:30
Marek Vasut
c1d264e84e spi: imx: Implement set_speed
The set_speed() callback should configure the bus speed, make it so.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2021-02-26 13:25:21 +05:30
Tom Rini
cbe607b920 Xilinx changes for v2021.04-rc3
qspi:
 - Support for dual/quad mode
 - Fix speed handling
 
 clk:
 - Add clock enable function for zynq/zynqmp/versal
 
 gem:
 - Enable clock for Versal
 - Fix error path
 - Fix mdio deregistration path
 
 fpga:
 - Fix buffer alignment for ZynqMP
 
 xilinx:
 - Fix reset reason clearing in ZynqMP
 - Show silicon version in SPL for Zynq/ZynqMP
 - Fix DTB selection for ZynqMP
 - Rename zc1275 to zcu1275 to match DT name
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYDUezQAKCRDKSWXLKUoM
 IbtgAJ9jZ+BOtwFaHR19TENC2DsHTINnnwCfSDn3fU0OFJRI0HD7pRxXr4xrb3M=
 =Kr8x
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2021.04-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze

Xilinx changes for v2021.04-rc3

qspi:
- Support for dual/quad mode
- Fix speed handling

clk:
- Add clock enable function for zynq/zynqmp/versal

gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path

fpga:
- Fix buffer alignment for ZynqMP

xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
2021-02-23 10:45:55 -05:00
Brandon Maier
d9aa19efa8 spi: zynqmp_gqspi: fix set_speed bug on multiple runs
If zynqmp_qspi_set_speed() is called multiple times with the same speed,
then on the second call it will skip recalculating the baud_rate_val as
it assumes the speed is already configured correctly. But it will still
write the baud_rate_val to the configuration register and call
zynqmp_gqspi_set_tapdelay(). Because it skipped recalculating the
baud_rate_val, it will use the initial value of 0 . This causes the
driver to run at maximum speed which for many spi flashes is too fast and
causes data corruption.

Instead only write out a new baud_rate_val if we have calculated the
correct baud_rate_val.

This opens up another issue with the "if (speed == 0)", we don't save
off the new plat->speed_hz value when setting the baud rate on the
speed=0 path. Instead mimic what the Linux zynqmp gqspi driver does, and
have speed==0 just use the same calculation as a normal speed. That will
cause the baud_rate_val to use the slowest speed possible, which is the
safest option.

Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
CC: jagan@amarulasolutions.com
CC: michal.simek@xilinx.com
CC: Ashok Reddy Soma <ashokred@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-02-23 14:56:59 +01:00
Michal Simek
9b7aac7536 clk: zynq: Add dummy clock enable function
A lot of Xilinx drivers are checking -ENOSYS which means that clock driver
doesn't have enable function. Remove this checking from drivers and create
dummy enable function as was done for clk_fixed_rate driver by
commit 6bf6d81c11 ("clk: fixed_rate: add dummy enable() function").

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-02-23 14:56:59 +01:00
Tom Rini
2ae80437fb Merge branch '2021-02-02-drop-asm_global_data-when-unused'
- Merge the patch to take <asm/global_data.h> out of <common.h>
2021-02-15 10:16:45 -05:00
Mathew McBride
fd20097336 spi: fsl_qspi: apply the same settings for LS1088 as LS208x
The LS1088 requires the same QUADSPI_QURIK_BASE_INTERNAL
workaround as the LS208x and also has a 64 byte TX buffer.

With the previous settings SPI-NAND reads over AHB were
corrupted.

Fixes: 91afd36f38 ("spi: Transform the FSL QuadSPI driver to use the SPI MEM API")
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:18 +05:30
Mathew McBride
6b4eb604ea spi: fsl_qspi: Ensure width is respected in spi-mem operations
Adapted from kernel commit b0177aca7aea
From: Michael Walle <michael@walle.cc>

Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.

Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.

Fixes: 91afd36f38 ("spi: Add a driver for the Freescale/NXP QuadSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200114154613.8195-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mathew McBride <matt@traverse.com.au> [adapt for U-Boot]
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:18 +05:30
Brandon Maier
f1fd79afad spi: zynqmp_gqspi: support dual and quad mode
The dm_spi_ops.xfer() API does not support dual and quad SPI modes. It
also doesn't allow the zynqmp_gqspi driver to calculate the correct
number of dummy cycles for some NOR ops (as doing so also requires the
buswidth).

Port the zynqmp_gqspi driver to spi_controller_mem_ops, which gives us
the buswidth values to correctly support all SNOR_PROTO_X_X_X commands
and to properly calculate dummy cycles.

Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
CC: jagan@amarulasolutions.com
CC: michal.simek@xilinx.com
CC: Ashok Reddy Soma <ashokred@xilinx.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-02-03 13:36:44 +01:00
Simon Glass
401d1c4f5d common: Drop asm/global_data.h from common header
Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-02 15:33:42 -05:00
SkyLake.Huang
7a49d61742 spi: mtk_snor: add support for MTK SPI NOR controller
This patch adds support for MTK SPI NOR controller, which you
can see on mt7622 & mt7629.

1. This controller is designed only for SPI NOR. We can't adjust
its bus clock dynamically. Set clock in dts instead.
2. This controller only supports 1-1-1 write mode.
3. Remove mtk_snor_match_read() since upper SPI-MEM layer already
handles command.
4. sf read/write/update commands are tested with this driver.

Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
2021-01-29 10:35:14 -05:00
Tom Rini
c99be953e7 - MIPS: add support for Mediatek MT7620 SoCs
-----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEiQkHUH+J02LLC9InKPlOlyTyXBgFAmAN21EACgkQKPlOlyTy
 XBgzBw/+LUzGufIop4CimnEhqrfKRuoSKinRWhx8Lo4PyjF5SAwLgIyCWY95PoQf
 eDka+Ufyj1TbvqbPR+bhJbdL7wFrku3iKE7b0Ni8AamkmsyybxAVeyByen0Q1mSF
 q4KoPhKJmpdZOfrUVrXZBBwG7/T1WTHMrCc2ZSacR0G/IeimgLplT4sRk/uG1eFo
 uiKYf0/AjD28WNvlE9Dq0EZQA+KsTe/q7GQ79nOTuxYTOjbPA59WXTOtZMo1cPgc
 GhT1EJr4N7OcGvxgkiZ8Gs4mYMbFFVvMAUNW1Bsx4v1aYJyfgP0ua58gTnWSMn69
 OJNdxTs+JYBSIZd0B8gNf0P1ZQgrGACA1Vq4O3xJUImtkzp0tMID97ZwvAdhJQbo
 MhNrWcIxijrzWDHEGhnyZ0wyqWmSwznsrvIlS9hMuIxxmnYKveTwfkCeVcvkwvn7
 Nc1Pls1Lt2ViP8/Nygc+fAMg30vtp+NvSrbA53foka62sJMqmWAjPEprPPlJV0Z2
 qGJWCxIJ/1YAUjkNrEnSo/2A3SSAM8wA1ku6aT/Ju7NZCx/3m7sYXE+wQuxYlU2I
 zxQDO+2H0v0nlVVWebQZGZx8sn6Z4O+aGCLAkpJ9tqrViJYhy0Ti2QZi0Udcl1Ny
 lADQXQM2iPoQ2zJlO4AmzXCZ7DLrKVeS3hFFiVxRWK16apckz+o=
 =fKDK
 -----END PGP SIGNATURE-----

Merge tag 'mips-pull-2021-01-24' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips

- MIPS: add support for Mediatek MT7620 SoCs
2021-01-25 14:38:40 -05:00
Weijie Gao
2db6fba051 spi: add spi controller support for MediaTek MT7620 SoC
This patch adds spi controller support for MediaTek MT7620 SoC.

The SPI controller supports two chip selects. These two chip selects are
implemented as two separate register groups, but they share the same bus
(DI/DO/CLK), only CS pins are dedicated for each register group.
Appearently these two register groups cannot operates simulataneously so
they are implemented as one controller.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2021-01-24 21:39:26 +01:00
Marek Vasut
38b92ca196 spi: imx: Use clock framework if enabled
In case the clock framework is enabled, enable the SPI controller clock
and obtain max frequency from the clock framework.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
2021-01-23 13:40:29 +01:00
Marek Vasut
6cd4f48b64 spi: imx: Define register bits in the driver
The CSPI/ECSPI register bits do not differ between newer SoCs, instead
of having multiple copies of the same thing for each iMX SoC, define
the bits in the driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
2021-01-23 13:40:29 +01:00
Adam Ford
5fb6b82471 spi: nxp_fspi: Enable support for nxp,imx8mm-fspi
The i.MX8M Mini can use the FlexSPI driver.  Add support
for it to the driver.

Signed-off-by: Adam Ford <aford173@gmail.com>
2021-01-23 13:40:29 +01:00
Dario Binacchi
b0db69b4e1 dm: fix build errors generated by last merges
Something was wrong in the merge process into the mainline.
Some added patches access driver structure fields and functions that
have been modified by previous patches.
The patch renames:
 - dev_get_platdata to dev_get_plat
 - dev_get_uclass_platdata to dev_get_uclass_plat
 - ofdata_to_platdata to of_to_plat
 - plat_data_alloc_size to plat_auto
 - priv_auto_alloc_size to priv_auto
 - video_uc_platdata to video_uc_plat

Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-01-15 13:12:38 -05:00
Patrick Delaunay
162f5888e7 spi: stm32_qspi: migrate trace to dev and log macro
Change debug/pr_* to log_* or dev_* macro and define LOG_CATEGORY.

Remove the "%s:" __func__  header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13 09:52:58 +01:00
Patrick Delaunay
7a41cb50ce spi: stm32_spi: migrate trace to dev and log macro
Change debug/pr_debug to log_debug or dev_dbg macro and
define LOG_CATEGORY.

Remove the "%s:" __func__  header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13 09:52:58 +01:00
Vignesh Raghavendra
f3f83ad4ca spi: omap3_spi: Fix speed and mode selection
McSPI IP provides per CS specific speed and mode selection. Therefore it
is possible to apply these settings only after CS is known. But
set_speed and set_mode can be called without bus being claimed, this
would lead driver to set up wrong CS (or previously used CS).

Fix this by apply set_speed and set_mode only if bus is already claimed.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
2021-01-12 10:21:41 +05:30
Ovidiu Panait
705082d4b1 spi: ti_qspi: Fix "spi-max-frequency" error path in ti_qspi_ofdata_to_platdata
struct ti_qspi_priv->max_hz is declared as unsigned int, so the following
error path check will always be false, even when "spi-max-frequency"
property is invalid/missing:
  priv->max_hz = fdtdec_get_int(blob, node, "spi-max-frequency", -1);
  if (priv->max_hz < 0) {
    ...
  }

Replace the fdtdec call with dev_read_u32_default() and use 0 as the
default value. Error out if max_hz is zero.

Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
2021-01-12 10:21:41 +05:30
Tom Rini
bc0b99bd8b Xilinx changes for v2021.04
arm64:
 - DT updates
 
 microblaze:
 - Add support for NOR device support
 
 spi:
 - Fix unaligned data write issue
 
 nand:
 - Minor code change
 
 xilinx:
 - Fru fix in limit calculation
 - Fill git repo link for all Xilinx boards
 
 video:
 - Add support for seps525 spi display
 
 tools:
 - Minor Vitis file support
 
 cmd/common
 - Minor code indentation fixes
 
 serial:
 - Uartlite debug uart initialization fix
 -----BEGIN PGP SIGNATURE-----
 
 iFsEABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX/ROlgAKCRDKSWXLKUoM
 IRC5AIkBzg4Sz8fQgdCiOK89k7tdFKMAnA9SYhgm4TSCzffZCJwnm78QoGAC
 =4FnY
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2021.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next

Xilinx changes for v2021.04

arm64:
- DT updates

microblaze:
- Add support for NOR device support

spi:
- Fix unaligned data write issue

nand:
- Minor code change

xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards

video:
- Add support for seps525 spi display

tools:
- Minor Vitis file support

cmd/common
- Minor code indentation fixes

serial:
- Uartlite debug uart initialization fix
2021-01-06 07:57:33 -05:00
Tom Rini
b11f634b1c Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
 dtoc: Tidy up and add more tests
 ns16550 code clean-up
 x86 and sandbox minor fixes for of-platdata
 dtoc prepration for adding build-time instantiation
 -----BEGIN PGP SIGNATURE-----
 
 iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
 bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
 KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
 HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
 59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
 2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
 LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
 =9kN3
 -----END PGP SIGNATURE-----

Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next

Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
2021-01-05 22:34:43 -05:00
Tom Rini
720620e691 Prepare v2021.01-rc5
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAl/0YVIACgkQFHw5/5Y0
 tywtEwv/cJWlKgcSnYjuJrxwuJdauUTfXdbUgtCxOtBw/BP4dsKkbGTJPw5q5M+4
 LJJSKyksmJVTX26h1dpkzQjOpWtTDnWqm5CTIxD52oQD7pxK+zCQ9T6S+QbQD0Se
 ogHmZluzFoluxbNgo8tiO52xvMhDO3TVAzxsNDdGfkd5/tAXOHClPc34RmAkdRHU
 VsR89AKdT2q543fiUfrRZYDzdctaNWhRGXMDcJ4+QU/8hQhrpcr8EtHbF+3mWX4K
 pA01pDz150Rn4UI6S2xKEWrjSTHe55fxVj/Qj0rq9z2E/+NqGXemf5s13AR0G/z3
 PqHdVLHzDe64pbOvmyU1pVQ0aMb8vMJUnqx68SQZY3On2c+MjRWQ+7aVVaKOcPGp
 uatk6QMrggHp3Li+3yZrLBE0qPr/sNMVb7mUesdZb6lFd2VIs8siwhfeGXMS+nDI
 xePzsR43Fnn5Q5KIqqvcWUb+TTTqUDUff0wyAU8NBgCaIBIZK8h2ppS1jjnbms0I
 mr8Er2vb
 =Dfum
 -----END PGP SIGNATURE-----

Merge tag 'v2021.01-rc5' into next

Prepare v2021.01-rc5

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-01-05 16:20:26 -05:00
Simon Glass
bdf8fd76c0 dm: Rename U_BOOT_DRIVER_ALIAS to DM_DRIVER_ALIAS
We use the U_BOOT_ prefix (i.e. U_BOOT_DRIVER) to declare a driver but
in every other case we just use DM_. Update the alias macros to use the
DM_ prefix.

We could perhaps rename U_BOOT_DRIVER() to DM_DRIVER(), but this macro
is widely used and there is at least some benefit to indicating it us a
U-Boot driver, particularly for code ported from Linux. So for now, let's
keep that name.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05 12:26:35 -07:00
Simon Glass
f10643cf8a dm: core: Access device ofnode through functions
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05 12:24:41 -07:00
Simon Glass
7d14ee443c dm: core: Use dev_has_ofnode() instead of dev_of_valid()
We have two functions which do the same thing. Standardise on
dev_has_ofnode() since there is no such thing as an 'invalid' ofnode in
normal operation: it is either null or missing.

Also move the functions into one place.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2021-01-05 12:24:41 -07:00
Simon Glass
a53f6fad7e x86: spl: Move priv/plat structs to headers
With the new of-platdata, these need to be available to dt_platdata.c
so must be in header files. Move them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05 12:24:41 -07:00
Simon Glass
0fd3d91152 dm: Use access methods for dev/uclass private data
Most drivers use these access methods but a few do not. Update them.

In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
2021-01-05 12:24:40 -07:00