Commit graph

66 commits

Author SHA1 Message Date
Jason Wessel
3d36be0300 Remove all the search paths from the .lds files.
The cross compiler is responsible for providing the correct libraries
and the logic to find the linking libraries.

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
2008-04-17 23:57:32 -07:00
Stefan Roese
e4170e5a50 ppc4xx: Fix comment in 405EX DDR2 init code
Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15 07:22:15 +01:00
Stefan Roese
be88b16998 ppc4xx: Fix remaining CONFIG_COMMANDS in 4xx files
Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-17 07:50:17 +01:00
Stefan Roese
a0dd99d51e ppc4xx: Update Kilauea CPLD configuration with USB PHY reset bit
Now that bit 29 is the USB PHY reset bit, update the Kilauea port
to remove the USB PHY reset after powerup. The CPLD will keep the
USB PHY in reset (active low) until the bit is set to 1 in
board_early_init_f().

Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-14 10:05:05 +01:00
Wolfgang Denk
64134f0112 Fix linker scripts: add NOLOAD atribute to .bss/.sbss sections
With recent toolchain versions, some boards would not build because
or errors like this one (here for ocotea board when building with
ELDK 4.2 beta):
ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab]

For many boards, the .bss section is big enough that it wraps around
at the end of the address space (0xFFFFFFFF), so the problem will not
be visible unless you use a 64 bit tool chain for development. On
some boards however, changes to the code size (due to different
optimizations) we bail out with section overlaps like above.

The fix is to add the NOLOAD attribute to the .bss and .sbss
sections, telling the linker that .bss does not consume any space in
the image.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-12 20:31:39 +01:00
Stefan Roese
8697e6a19b ppc4xx: Bring 4xx fdt support up-to-date
This patch update the 4xx fdt support. It enabled fdt booting
on the AMCC Kilauea and Sequoia for now. More can follow later
quite easily.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-13 14:52:53 +01:00
Stefan Roese
7cfc12a7dc ppc4xx: 405EX: Correctly enable USB pins
This patch selects the USB data pins in the 405EX GPIO and MFC (multi
function control) registers. This is done for the AMCC Kilauea and
Makalu eval boards.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-08 14:47:34 +01:00
Stefan Roese
e15e33433e ppc4xx: Kilauea: Add PCIe reset assertion upon power-up
This manual PCIe reset triggering solves the problem seen with the
Intel EPRO/1000 card, which was not detected (link not established)
upon power-up reset.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-30 07:15:41 +01:00
Stefan Roese
c9672f81f1 ppc4xx: Small AMCC Kilauea cleanup
Remove not needed pci_target_init() function.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-15 14:25:09 +01:00
Stefan Roese
654f38b3a3 ppc4xx: Make output a little shorter on PCIe detection
Now not max 3 lines but 2 lines are printed per PCIe port.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-05 07:43:05 +01:00
Stefan Roese
3d6cb3b24a ppc4xx: Add AMCC Kilauea/Haleakala NAND booting support
This patch adds NAND booting support for the AMCC 405EX(r) eval boards.
Again, only one image supports both targets.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-03 12:08:28 +01:00
Stefan Roese
353f2688b4 ppc4xx: Add initial AMCC Haleakala PPC405EXr eval board support
The Haleakala is nearly identical with the Kilauea eval board. The only
difference is that the 405EXr only supports one EMAC and one PCIe
interface. This patch adds support for the Haleakala board by using
the identical image for Kilauea and Haleakala. The distinction is done
by comparing the PVR.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:51 +01:00
Stefan Roese
770c7af580 ppc4xx: Fix size setup in Kilauea DDR2 init routine
The size was initilized wrong. Instead of 256MB, the DDR2 controller
was setup to 512MB. Now the correct values is used.

This patch also does a little cleanup and adds a comment here.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:50 +01:00
Stefan Roese
d4cb2d1794 ppc4xx: Dynamic configuration of 4xx PCIe mode as root or endpoint mode
This patch adds support for dynamic configuration of PCIe ports for the
AMCC PPC4xx boards equipped with PCIe interfaces. These are the PPC440SPe
boards Yucca & Katmai and the 405EX board Kilauea.

This dynamic configuration is done via the "pcie_mode" environement
variable. This variable can be set to "EP" or "RP" for endpoint or
rootpoint mode. Multiple values can be joined via the ":" delimiter.
Here an example:

pcie_mode=RP:EP:EP

This way, PCIe port 0 will be configured as rootpoint, PCIe port 1 and 2
as endpoint.

Per default Yucca will be configured as:
pcie_mode=RP:EP:EP

Per default Katmai will be configured as:
pcie_mode=RP:RP:REP

Per default Kilauea will be configured as:
pcie_mode=RP:RP

Signed-off-by: Tirumala R Marri <tmarri@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:50 +01:00
Stefan Roese
fd671802b6 ppc4xx: Enable device tree support (fdt) on Kilauea per default
This patch enables the fdt support on the AMCC Kilauea eval board.
Additionally now EBC ranges fdt fixup is included to support NOR
FLASH mapping via the Linux physmap_of driver.

This Kilauea port now support booting arch/ppc and arch/powerpc
Linux kernels. The default environment "net_nfs" is for arch/ppc
and "net_nfs_fdt" is for arch/powerpc. In the long run, arch/ppc
support will be removed.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:50 +01:00
Stefan Roese
566806ca1a ppc4xx: Add initial AMCC Kilauea 405EX support
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:49 +01:00