Commit graph

132 commits

Author SHA1 Message Date
Maxime Ripard
bf8f4c4400 MAINTAINERS: Update email address for Maxime Ripard
Free Electrons is no more and is now known as Bootlin, change my email
address accordingly.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-02-04 19:21:00 -05:00
Maxime Ripard
3afdfd8ddc sunxi: maintainers: Add myself for the TBS A711
Support for that board got introduced recently without the maintainers
part. Let's fix that.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2018-01-10 11:30:49 +05:30
Chen-Yu Tsai
afe2754412 sunxi: Add support for Libre Computer Board ALL-H3-CC H3 ver.
The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board computer based on the Allwinner H3 SoC.
The board has 1GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes
and connectors are in the exact same position as on the Raspberry Pi B+.

Raspberry Pi B+ like peripherals supported on this board include:

  - Power input through micro-USB connector (without USB OTG)
  - Native 100 Mbps ethernet using the internal PHY, as opposed to
    USB-based on the RPi
  - 4x USB 2.0 host ports, directly connected to the SoC, as opposed to
    being connected through a USB 2.0 hub on the RPi
  - TV and audio output on a 3.5mm TRRS jack
  - HDMI output
  - Micro-SD card slot
  - Standard RPi B+ GPIO header, with the standard peripherals routed to
    the same pins.

    * 5V, 3.3V power, and ground
    * I2C0 on the H3 is routed to I2C1 pins on the RPi header
    * I2C1 on the H3 is routed to I2C0 pins on the RPi header
    * UART1 on the H3 is routed to UART0 pins on the RPi header
    * SPI0 on the H3 is routed to SPI0 pins on the RPi header,
      with GPIO pin PA17 replacing the missing Chip Select 1
    * I2S1 on the H3 is routed to PCM pins on the RPi header

  - Additional peripherals from the H3 are available on different pins.
    These include I2S0, JTAG, PWM1, SPDIF, SPI1, and UART3

In addition, there are a number of new features:

  - Console UART header
  - Consumer IR receiver
  - Camera interface (not compatible with RPi)
  - Onboard microphone
  - eMMC expansion module port
  - Heatsink mounting holes

This patch adds defconfig and dts files for this board. The dts file is
the same as the one submitted for inclusion in Linux, with some minor
revisions to match the dtsi file and old EMAC bindings in U-boot.

Since the OTG controller is wired to a USB host port, and the H3 has
proper USB hosts to handle host mode, the MUSB driver is not enabled.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2018-01-10 11:27:41 +05:30
Antony Antony
6130b1f6bc sun50i: h5: Add NanoPi Neo Plus2 DT initial support
Add initial DT for NanoPi NEO Plus2 by FriendlyARM
- Allwinner quad core H5 Cortex A53 with an ARM Mali-450MP GPU
- 1 GB DDR3 RAM
- 8GB eMMC flash (Samsung KLM8G1WEPD-B031)
- micro SD card slot
- Gigabit Ethernet (external RTL8211E-VB-CG chip)
- 802.11 b/g/n WiFi, Bluetooth 4.0 (Ampak AP6212A module)
- 2x USB 2.0 host ports

Signed-off-by: Antony Antony <antony@phenome.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-11-21 19:11:57 +05:30
Tom Rini
79df00fdb4 MAINTAINERS: Add missing boards and config entries
As part of my usual round of build testing, output about missing
MAINTAINERS information was not logged, and thus often overlooked.
Correct that mistake by ensuring that I log the output of
genboardscfg.py every time.  As part of that, address a number of
missing MAINTAINERS entires.  In the case of a missing file, I have put
the original submitter down.  In the rest of the cases I have added the
config (and sometimes relevant header file) to the existing set of file
globs.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-06 09:58:51 -05:00
Jagan Teki
ea5b1e1efb sun7i: a20: Add Bananapi M1 Plus support
Banana Pi M1 Plus is an open-source single-board computer
that adds more connectivity to the classic board using
Allwinner A20 SOC.

Bananapi M1-Plus features:
- A20 Dual-core 1.0GHz
- 1 GB DDR3 SDRAM
- MicroSD
- 10/100/1000 Ethernet RJ45
- WiFi b/g/n
- 5V DC Micro USB power-supply

For dts file,
Sync with Linux commit f92ca09("Merge branch 'akpm/master'").

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-10-03 19:12:06 +02:00
Jagan Teki
585bf8ae6f sun50i: a64: Add A64-OLinuXino initial support
OLimex A64-OLinuXino is an open-source hardware board
using the Allwinner A64 SOC.

OLimex A64-OLinuXino has
- A64 Quad-core Cortex-A53 64bit
- 1GB or 2GB RAM DDR3L @ 672Mhz
- microSD slot and 4/8/16GB eMMC
- Debug TTL UART
- HDMI
- LCD
- IR receiver
- 5V DC power supply

Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-08-15 11:30:59 +05:30
Jagan Teki
f322657204 sun50i: a64: Add initial NanoPi A64 support
NanoPi A64 is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner A64 SOC.

Nanopi A64 features
- Allwinner A64, 64-bit Quad-core Cortex-A53@648MHz to 1.152GHz, DVFS
- 1GB DDR3 RAM
- MicroSD
- Gigabit Ethernet (RTL8211E)
- Wi-Fi 802.11b/g/n
- IR receiver
- Audio In/Out
- Video In/Out
- Serial Debug Port
- microUSB 5V 2A DC power-supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2017-08-15 11:30:19 +05:30
Olliver Schinagl
335d30050b sun7i: Add support for Olimex A20-OLinuXino-LIME2-eMMC
This patch adds support for the Olimex OLinuXino Lime2 with eMMC flash
storage.
https://www.olimex.com/Products/OLinuXino/A20/A20-OLinuXino-LIME2-eMMC/

It is a assembly variant of the regular Lime2 but featuring eMMC for
storage.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-08-11 15:16:39 +05:30
Jagan Teki
2b1a33213e sun50i: h5: Add initial NanoPi NEO2 support
NanoPi NEO2 is designed and developed by FriendlyElec
using the Allwinner 64-bit H5 SOC.

NanoPi Neo2 key features
- Allwinner H5, Quad-core 64-bit Cortex-A53
- 512MB DDR3 RAM
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC MicroUSB power-supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-14 20:25:56 +05:30
Jagan Teki
bdf9577355 sun50i: a64: Add initial Orangepi Win/WinPlus support
Orangepi Win/WinPlus is an open-source single-board computer
using the Allwinner A64 SOC.

A64 Orangepi Win/WinPlus has
- A64 Quad-core Cortex-A53 64bit
- 1GB(Win)/2GB(Win Plus) DDR3 SDRAM
- Debug TTL UART
- Four USB 2.0
- HDMI
- LCD
- Audio and MIC
- Wifi + BT
- IR receiver
- 5V DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-14 15:58:39 +05:30
Jagan Teki
d6b1d7d81b sun50i: h5: Add initial Orangepi Zero Plus 2 support
Orangepi Zero Plus 2 is an open-source single-board computer
using the Allwinner h5 SOC.

H5 Orangepi Zero Plus 2 has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG+power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-14 15:52:19 +05:30
Icenowy Zheng
84580628b8 sunxi: add a defconfig for SoPine w/ official baseboard
The SoPine is a SoM by Pine64, with an Allwinner A64 SoC, a LPDDR3 DRAM
chip, an AXP803 PMIC, a SPI NOR Flash and a MicroSD slot. The card
detect pin of the MicroSD slot is broken, however, it doesn't matter as
the design of SoPine didn't allow hot-swapping the MicroSD card (The
MicroSD slot is at the back of the SoM, and when the SoM is installed on
the baseboard, it's nearly impossible to remove the MicroSD).

The official baseboard of it is a board with nearly the same connectors
with the original Pine64+, with the MicroUSB power jack replaced, and
at the position of MicroSD slot a eMMC module slot is added.

Add support for SoPine with the official baseboard by adding its
defconfig file. It still uses the device tree of Pine64, however, it
will change after a proper device tree of SoPine with baseboard is
accepted by Linux mainline.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Update board/sunxi/MAINTAINERS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-08 22:37:55 +05:30
Jagan Teki
b0174c39b3 sun8i: h3: Add initial NanoPi M1 Plus support
NanoPi M1 Plus is designed and developed by FriendlyElec
for professionals, enterprise users, makers and hobbyists
using the Allwinner H3 SOC.

NanoPi M1 Plus key features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 1GB DDR3 RAM
- 8GB eMMC
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC power-supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-08 21:48:23 +05:30
Jagan Teki
868e37159e sun50i: h5: Add initial Orangepi Prime support
Orangepi Prime is an open-source single-board computer
using the Allwinner h5 SOC.

H5 Orangepi Prime has
- Quad-core Cortex-A53
- 2GB DDR3
- Debug TTL UART
- 1000M/100M Ethernet RJ45
- Three USB 2.0
- HDMI
- Audio and MIC
- Wifi + BT
- IR receiver
- HDMI
- Wifi + BT

Boot from MMC:
-------------
U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE:  BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
NOTICE:  Configuring SPC Controller
NOTICE:  BL3-1: v1.0(debug):aa75c8d
NOTICE:  BL3-1: Built : 18:28:27, May 24 2017
INFO:    BL3-1: Initializing runtime services
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9

U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000) Allwinner Technology

CPU:   Allwinner H5 (SUN50I)
Model: OrangePi Prime
DRAM:  2 GiB
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   phy interface7
eth0: ethernet@1c30000
starting USB...
USB0:   USB EHCI 1.00
USB1:   USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot:  0

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-06-02 13:28:07 +00:00
Jagan Teki
2dbe9c1362 sun50i: a64: Add initial Banana Pi M64 support
BPI-M64 is a 64-bit quad-core mini single board computer
using the Allwinner A64 SOC.

BPI-M64 features
- 1.2 Ghz Quad-Core ARM Cortex A53
- 2GB DDR3 SDRAM with 733MHz
- MicroSD/eMMC(8GB)
- 10/100/1000Mbps ethernet (Realtek RTL8211E/D)
- Wifi + BT
- IR receiver
- Audio In/Out
- Video In/Out
- 5V 2A DC power-supply

For dts file,
Sync with Linux commit 4879b7ae("Merge tag 'dmaengine-4.12-rc1'").

Boot from MMC:
-------------
U-Boot SPL 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE:  BL3-1: Running on A64/H64 (1689) in SRAM A2 (@0x44000)
NOTICE:  Configuring SPC Controller
NOTICE:  BL3-1: v1.0(debug):aa75c8d
NOTICE:  BL3-1: Built : 18:28:27, May 24 2017
NOTICE:  Configuring AXP PMIC
NOTICE:  PMIC: setup successful
INFO:    BL3-1: Initializing runtime services
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9

U-Boot 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31 +0000) Allwinner Technology

CPU:   Allwinner A64 (SUN50I)
Model: BananaPi-M64
DRAM:  2 GiB
MMC:   SUNXI SD/MMC: 0, SUNXI SD/MMC: 1
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot:  0

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-06-01 09:26:05 +00:00
Mylene JOSSERAND
a647ea172a sunxi: Add support for NanoPi M1
NanoPi M1 is a board based on Allwinner H3 CPU.

This commit adds the support for this platform with:
   - an include device tree which enables UART, LEDs, GPIO key switch,
   1 USB host ports and the SD-card as a dtsi file.
   - a device tree specific to this board that enables the
   2 additional USB ports
   - a defconfig file for minimal support
   - a section in MAINTAINERS (add myself)

Synchronized with the kernel device tree, from commits:
sun8i-nanopi.dtsi: 85d2913614d9ab899d23b7ab7d22d23cf45bd1de
sun8i-h3-nanopi-m1.dts: 10efbf5f16336b7540ad6a16aa1cb0b26bab033b

Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-30 11:05:09 +05:30
Andre Przywara
80b51b5aa9 sunxi: Move maintainership for Pine64
After speaking to Hans at FOSDEM, he is fine with transferring the
maintainership of the Pine64 boards over to me.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-05-17 23:24:49 +05:30
Icenowy Zheng
5a49b2929c sunxi: add support for Banana Pi M2 Plus board
Banana Pi M2 Plus is an Allwinner H3-based SBC by Sinovoip, which has
already mainline device tree file that have landed into U-Boot source
tree.

Add a defconfig file for it and add the MAINTAINERS items.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-05-04 19:46:23 +05:30
Icenowy Zheng
f02abb0608 sunxi: add support for Lichee Pi Zero
Lichee Pi Zero is a development board with a V3s SoC, which features
64MiB DRAM co-packaged within the SoC, a TF slot, a SPI NOR slot (not
soldered in production batch), a 40-pin RGB LCD connector and some extra
pins available as 2.54mm pins or stamp holes.

Add support for it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-21 09:29:35 +02:00
Chen-Yu Tsai
10d8bc5a59 sunxi: Add support for Bananapi M2 Ultra
The Bananapi M2 Ultra is the first publicly available development board
featuring the R40 SoC.

This patch add barebone dtsi/dts files for the R40 and Bananapi M2 Ultra,
as well as a defconfig for it.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:30:01 +02:00
Jelle van der Waa
27f31aac15 sunxi: Add maintainer of the NanoPi NEO Air
Add myself as maintainer of the NanoPi NEO Air board.

Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-18 10:50:13 +05:30
Rask Ingemann Lambertsen
58c4020cf0 arm: sunxi: Add Sunchip CX-A99 initial support
The Sunchip CX-A99 is a board used in some media players. It features:

An Allwinner A80 ARM SoC (4 * Cortex-A7 + 4 * Cortex-A15 cores)
2 GiB or 4 GiB DDR3 DRAM
AXP808 PMIC
16 GB or 32 GB eMMC
SDIO Wifi/Bluetooth/FM module
SD card slot
1 USB 3.0 connector
2 USB 2.0 connectors
SATA connector
UART connector (internally) for serial console
Ethernet connector (10/100/1000 Mbit/s)
HDMI connector
Composite video and analog audio connector
S/PDIF connector
IR remote control receiver

This patch adds a defconfig for the board. The DRAM settings are as found
in the vendor sys_config.fex file.

It has a preliminary device tree for use until a device tree is accepted
upstream, after which it can be replaced by the upstream version.

Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
[squash commits, and edited new meanful commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-07 11:23:46 +05:30
Andre Przywara
e7bd15ea15 sunxi: Add OrangePi PC 2 initial support
The OrangePi PC 2 is a typical SBC with the 64-bit Allwinner H5 SoC.
Add a (64-bit only) defconfig defining the required options to build
the U-Boot proper.

Create a new .dts file for it by including the (32-bit) H3 SoC .dtsi
and changing the differing components accordingly.
This is a preliminary device tree mostly for U-Boot's own sake, it
is expected to be updated once the official DT gets accepted upstream.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[squash the commits, update the commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-05 15:03:17 +05:30
Icenowy Zheng
485329a578 sunxi: add orangepi zero defconfig
Orange Pi Zero is a board designed by Xunlong. It has an Allwinner H2+
SoC (similar to H3, which shares the same SoC ID), 256MB/512MB RAM,
Allwinner XR819 SDIO Wi-Fi, a MicroUSB port which is used to power the
board (also capable of OTG), a USB Type-A socket and a MicroSD slot.

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-01-15 18:16:12 +01:00
FUKAUMI Naoki
5782954c2b sunxi: add support for Nintendo NES Classic Edition
Add board support for sun8i_r16 Nintendo NES Classic edition.

Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
[jagan: Add commit message body]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-11-28 15:10:30 -05:00
Chen-Yu Tsai
fda9d5d327 sunxi: Add support for Cubieboard4
The Cubieboard4 is an A80 SoC based development board from Cubietech.

This board has a UART port, 4 USB host ports, a USB 3.0 OTG connector,
HDMI and VGA outputs, a micro SD slot, 8G eMMC flash, 2G DRAM, a WiFi/BT
combo chip, headphone and microphone jacks, IR receiver, and GPIO headers.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-10-30 11:38:05 +01:00
Chen-Yu Tsai
3e057e48b5 sunxi: Enable SPL support for A80 Optimus board
The A80 Optimus Board was launched with the Allwinner A80 SoC.
It was jointly developed by Allwinner and Merrii.

This board has a UART port, a JTAG connector, 2 USB host ports, a USB
3.0 OTG connector, an HDMI output, a micro SD slot, 16G eMMC flash,
2G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone
jack, IR receiver, and additional GPIO headers.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[hdegoede@redhat.com: update existing Merrii_A80_Optimus_defconfig
 instead of adding a new defconfig]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-10-30 11:38:04 +01:00
Jelle van der Waa
348df5b92c sunxi: Add defconfig and dts for the NanoPi NEO
The NanoPi NEO is a simple h3 board with 512MB RAM, ethernet, one usb
and one usb OTG connector.

Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-09-18 14:39:16 +02:00
Hans de Goede
de300ea5db sunxi: Add defconfig and dts file for the Orange Pi Plus2E SBC
The Orange Pi Plus2E is an extended version of the Orange Pi Pc Plus,
with 2G RAM and an external gbit ethernet phy.

The dts file is identical to the one submitted to the upstream kernel,
except that it has the pending patch to enable the ethernet controller
squashed in, as u-boot already has sun8i-emac support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-09-03 13:05:43 +02:00
Stefan Mavrodiev
ca5c37026b sunxi: Add support for A33-OLinuXino board
A33-OLinuXino is A33 development board designed by Olimex LTD.

It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.

It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.

The dts files are identical to the ones submitted to the upstream kernel.

Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-09-03 10:33:44 +02:00
Icenowy Zheng
6d973ad9d2 sunxi: Add iNet D978 rev2 defconfig
The iNet D978 rev2 is a tablet board designed by iNet, which is intended to
use on 10" tablets with a appearance like Apple iPad. It has A33 SoC, 1GB
RAM, 8GB/16GB NAND, SDIO Wi-Fi, a MicroUSB port and a MicroSD slot.

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-09-03 10:04:15 +02:00
Hans de Goede
8d463c5a32 sun5i: Add defconfig and dts file for the Empire Electronix M712 tablet
Add a defconfig and dts file for the Empire Electronix M712 tablet, this
is a 7" A13 tablet, with micro-usb (otg), headphone and micro-sd slots on
the outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV
wifi chip and a DMART06 (1238a4) accelerometer.

The dts file is identical to the one submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-08-26 16:58:36 +02:00
Hans de Goede
a1243f7851 sun6i: Add defconfig and dts file for tablets using the inet-q972 PCB
Add a defconfig and dts file for tablets using the generic inet-q972 PCB.

Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host,
micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot,
(mini) power-barrel and an usb wifi module.

This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet.

The dts files are identical to the ones submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-08-26 16:58:36 +02:00
Hans de Goede
2a5adc5b3c sunxi: Add defconfig and dts file for the Orange Pi PC Plus SBC
There is a new Orange Pi PC *Plus* version available now,
this is an extended version of the regular Orange Pi PC
with sdio wifi and an eMMC.

The upstream kernel devs have decided that they want a separate
dts for the PC Plus rather then sharing a single dts between the
regular PC and the PC Plus. So add a new orangepi_pc_plus_defconfig
to match.

The added dts file matches the one submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-26 21:56:02 +02:00
Hans de Goede
66ab528673 sunxi: Add defconfig and dts file for the Orange Pi Lite SBC
The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.

The dts file is identical to the one submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-07-15 15:54:56 +02:00
Quentin Schulz
d2a6af0528 sunxi: Add defconfig and DTS file for Allwinner R16 EVB (Parrot)
The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.

The DTS file is identical to the one submitted to the upstream kernel.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-02 13:53:15 +02:00
Hans de Goede
3551b24f53 sunxi: Add defconfig and dts file for inet86dz board
The inet86dz board is a board used in 7" tablets from various oems.

These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.

The dts file this commit adds is identical to the one submitted to
the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-06-20 22:43:59 +02:00
Hans de Goede
cd38e3d1b4 sunxi: Add defconfig and dts file for Polaroid MID2407PXE03 tablet
The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.

The dts file is identical to the one submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-06-20 22:43:59 +02:00
Hans de Goede
ec770dba89 sunxi: Add defconfig and dts file for Orange Pi One SBC
The Orange Pi One SBC, is a stripped down version of the popular
Orange Pi PC. The one is a H3 based SBC, with 512M of RAM,
micro-sd slot, 1 host usb, 1 otg usb, hdmi and 100Mbit ethernet.

The dts is identical to the dts submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-04-12 08:58:03 +02:00
Siarhei Siamashka
7adbd1165c sunxi: Add Pine64+ support
The Pine64+ is a system based on the Allwinner A64 SoC. It is capable of
running AArch64 code and thus is the first of its kind for the sunxi target.

This patch adds a defconfig and device tree chunks for it.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: Change patch description]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01 09:52:28 +02:00
Hans de Goede
72cd013293 sunxi: Add defconfig and dts for Orange Pi 2 SBC
The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot,
4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI,
a TRRS headphone jack for stereo out and composite out, a microphone,
an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header
and a 40-pin GPIO header.

The added dts file is identical to the one submitted to the upstream
kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00
Hans de Goede
d1b7407c2f sunxi: Add defconfig and dts for Dserve DSRV9703C tablet
The Dserve DSRV9703C is a 9.7" A10 tablet with a 1024x768 ips LCD,
1G RAM, 4GB flash, a Focaltech FT5406EE8 touchscreen and rtl8188ctv wifi.

The dts file is identical to the one submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-23 22:04:13 +01:00
Peter Korsgaard
e133c5c350 sunxi: Add defconfig for yones toptech bs1078-v2 tablet
The yones toptech bs1078-v2 is a 10.1" tablet without any clear markings on
the outside, but 'YONESTOPTECH-BS1078' written on the PCB silkscreen.

It features a 16:9 1024:600 LCD, A31s SoC, 1GB RAM, 8G NAND, silead gsl3675
touchscreen and a RTL8723AS wifi chip:

https://linux-sunxi.org/Yones_Toptech_BS1078_V2

Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-23 22:04:13 +01:00
Chen-Yu Tsai
b953a6184e sunxi: Add defconfig for Sinlinx SinA31s
The Sinlinx A31s SDK is a A31s based module/baseboard development kit.

The core module has the SoC, PMIC, DRAM, eMMC and supporting components.
There are also pads for UART0, JTAG and I2S.

The baseboard has 100 Mbps Ethernet, 5x USB 2.0 host ports via a USB 2.0
hub chip, MMC, HDMI, SPDIF, CIR, audio jacks, 2 tablet-like volume
buttons, RS232 style UART and USB OTG (though VBUS is not connected).
Various headers are available for other addon modules, such as SDIO
WiFi, LCD display, camera sensor, UARTs, I2C, SPI and GPIOs.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-23 22:04:13 +01:00
Stefan Roese
2772f6d55c sunxi: Add defconfig for icnova-a20-swac
The ICnova-A20-SWAC is a baseboard, equipped with the ICnova-A20 SoM from
In-Circuit:

http://wiki.in-circuit.de/index.php5?title=ICnova_A20_SODIMM
http://linux-sunxi.org/In-Circuit_ICnova_A20

This patch adds support for this board, including ethernet, LCD and USB
support.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-23 22:04:13 +01:00
Marcus Cooper
c7c1b4ea89 sun7i: Add defconfig for the Itead Ibox
Add defconfig for the multi board device based on the
Allwinner A20 SoC. It contains the A20 Itead Core module and a
base board for the external interfaces.

The core module comes with 4GB NAND and 1GB DDR RAM.

The base board to which the core board is connected provides
3 USB 2.0 Host ports, 1 USB 2.0 OTG, 1 uSD slot, 10/100 Ethernet
port, HDMI, IR receiver,  SPDIF and a 32-pin GPIO header. This
header expands the features of core board by exposing the VGA pins,
audio In/Out pins, SATA, SPI, I2C, UARTS, USB-OTG and power..

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-23 22:04:13 +01:00
Chen-Yu Tsai
a9be871c1b sunxi: Add defconfig for Cubietruck Plus
Cubietruck Plus is a A83T/H8 based development board. The board has
standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host
via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet,
WiFi, headphone out / mic in, and various GPIO headers.

The board also has an EEPROM on i2c0 which holds the MAC address.

DLDO3 and DLDO4 provide power to the EMAC pins and PHY. Pin PA20
is connected to the reset control of the PHY. EMAC is not actually
supported yet.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-23 22:04:13 +01:00
Hans de Goede
6b3e71a38b sunxi: Add defconfig and dts for the Polaroid MID2809PXE4 tablet
The Polaroid MID2809PXE4 is a 9" tablet which is clearly marked
Polaroid MID2809PXE4 on the back. It features a 9" 16:9 800x480 LCD,
A23 Soc, 1GB RAM, 8GB NAND, gsl3670 touchscreen and esp8089 wifi.

The dts file is identical to the one submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00
Hans de Goede
c7e2ec4279 sunxi: Add defconfig and dts for Difrence DIT4350 tablet
The Difrnce dit4350 tablet is a tiny tablet with a 4.3" 16:9 480x272 LCD,
A13 SoC, 512M RAM, 4G NAND, solomon systech ssd2532qn6 touchscreen at
i2c1 address 0x48, Memsic MXC622X accelerometer at i2c1 address 0x15 and
rtl8188etv wifi.

The dts file is identical to the one submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00