* Add imx7d support for iomux controller
* imx7d has two iomux controllers iomuxc (0x3033000) and iomuxc-lpsr
(0x302C0000) each conroller provides control and mux mode pad
registers but shares iomuxc input select register with iomuxc-lpsr
IOMUX_CONFIG_LPSR flag is used to properly set daisy chain settings
for iomuxc-lpsr pads.
* Since mx7d introduces LPSR IOMUX pins, add new base to IOMUX v3
driver for these LPSR pins.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
On mx6 sabreauto board, there are two USB ports:
0: OTG
1: HOST
The EHCI driver is enabled for this board, but the IOMUX and VBUS power
control is not implemented, which cause both USB port failed to work.
This patch fix the problem by adding the board support codes.
Since the power control uses the GPIO pin from port expander MAX7310,
the PCA953X driver is enabled for accessing the MAX7310.
The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting
its daisy chain. Add a new function "imx_iomux_set_gpr_register" to
handle GPR register setting.
Signed-off-by: Ye.Li <B37916@freescale.com>
THe mx25 arch does not have a sys_proto.h file.
Instead of creating a dummy file, the file
is not included for this SOC.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Allow imx_iomux_v3_setup_multiple_pads to take a multi-cpu pad_list
and add macros for declaring the pad_list that take into account the
SoC types supported using CONFIG_MX6QDL (supports both the MX6Q and MX6DL
iomux).
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
On mx6sl there is a LVE (Low Voltage Enable) bit in the IOMUXC_SW_PAD_CTL
register that can enable or disable low voltage on the pad.
LVE is bit 22 of IOMUXC_SW_PAD_CTL register, but in order to make the
calculation easier we can define it as a flag in bit 1, since this bit is unused.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
This patch adds the IOMUX support for Vybrid VF610 platform.
There is a little difference for IOMUXC module between VF610 and i.MX
platform, the muxmode and pad configuration share one 32bit register on
VF610, but they are two independent registers on I.MX platform. A
CONFIG_IOMUX_SHARE_CONFIG_REG was introduced to fit this difference.
Signed-off-by: Alison Wang <b18965@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
They never return anything also than 0, so lets change the function
to void instead.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Up now only MX5 and MX6 can share code, because they have
a common source directory in cpu/armv7. Other not armv7
i.MX can profit of the same shared code. Move these files
into a directory accessible for all, similar to plat-mxc
in linux.
Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-09-10 14:24:29 +02:00
Renamed from arch/arm/cpu/armv7/imx-common/iomux-v3.c (Browse further)
