get_clocks is wrapped by CONFIG_FSL_CLK and CONFIG_M68K in seperate
piece code. They can be merged into one snippet.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: "angelo@sysam.it" <angelo@sysam.it>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: "Andreas Bießmann" <andreas.devel@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Angelo Dureghello <angelo@sysam.it>
CONFIG_BOOTDELAY is defined in config_distro_defaults.h
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
[trini: Drop omap3_logic.h settings which were a warning and no longer
correct usage].
Signed-off-by: Tom Rini <trini@konsulko.com>
Since busses are sorted in alphabetical order, introducing more
than nine busses led to unexpected behaviour.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
- i2c addresses for the videoboard port expanders were
wrong.
- the fpga reset signal was not initialized.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
The gdsys strider board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 1x 10/100 Mbit/s Ethernet (optional)
- Lattice ECP3 FPGA connected via eLBC
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
[trini: Drop setting CONFIG_SYS_GENERIC_BOARD, this is always true now]
Signed-off-by: Tom Rini <trini@konsulko.com>
DP501 only supports DP 1.1a.
Limit settings for link bandwidth and lane count to
values allowed by DP 1.1a.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
With Club 3D dual link adapter there are AUX-channel timeouts
when EDID is read. Increasing retry interval time to max (400us)
fixes this.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Heiko Schocher <hs@denx.de>
Bus has to be held for repeated start regardless of
read/write access.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
Reinhard Pfau complained that macros in ihs_i2c do not follow best practices.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
Fix below warnings happening for xilinx_zynqmp_ep_defconfig
drivers/net/zynq_gem.c: In function ‘zynq_gem_init’:
drivers/net/zynq_gem.c:330:7: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
((u32)(priv->rxbuffers) +
^
In file included from drivers/net/zynq_gem.c:19:0:
drivers/net/zynq_gem.c:336:10: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
writel((u32)priv->rx_bd, ®s->rxqbase);
^
./arch/arm/include/asm/io.h:146:34: note: in definition of macro ‘writel’
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
^
drivers/net/zynq_gem.c: In function ‘zynq_gem_send’:
drivers/net/zynq_gem.c:399:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
writel((u32)priv->tx_bd, ®s->txqbase);
^
./arch/arm/include/asm/io.h:146:34: note: in definition of macro ‘writel’
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
^
drivers/net/zynq_gem.c:404:22: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
priv->tx_bd->addr = (u32)ptr;
^
drivers/net/zynq_gem.c:409:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
addr = (u32) ptr;
^
drivers/net/zynq_gem.c:414:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
addr = (u32)priv->rxbuffers;
^
drivers/net/zynq_gem.c: In function ‘zynq_gem_recv’:
drivers/net/zynq_gem.c:454:31: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
net_process_received_packet((u8 *)addr, frame_len);
^
drivers/net/zynq_gem.c: In function ‘zynq_gem_initialize’:
drivers/net/zynq_gem.c:533:35: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
priv->rx_bd = (struct emac_bd *)((u32)bd_space + BD_SEPRN_SPACE);
^
drivers/net/zynq_gem.c:533:16: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
priv->rx_bd = (struct emac_bd *)((u32)bd_space + BD_SEPRN_SPACE);
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Fix below compilation warings happening for hikey_defconfig
drivers/usb/eth/smsc95xx.c:698:56: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
debug("** %s(), len %d, buf %#x\n", __func__, length, (int)msg);
^
include/common.h:109:26: note: in definition of macro ‘debug_cond’
printf(pr_fmt(fmt), ##args); \
^
drivers/usb/eth/smsc95xx.c:698:2: note: in expansion of macro ‘debug’
debug("** %s(), len %d, buf %#x\n", __func__, length, (int)msg);
^
drivers/usb/eth/smsc95xx.c:718:2: warning: format ‘%u’ expects argument of
type ‘unsigned int’, but argument 2 has type ‘long unsigned int’ [-Wformat=]
debug("Tx: len = %u, actual = %u, err = %d\n",
^
drivers/usb/eth/smsc95xx.c: In function ‘smsc95xx_recv’:
drivers/usb/eth/smsc95xx.c:802:19: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
cur_buf_align = (int)buf_ptr - (int)recv_buf;
^
drivers/usb/eth/smsc95xx.c:802:34: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
cur_buf_align = (int)buf_ptr - (int)recv_buf;
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Fix below compilation warings happening for hikey_defconfig
drivers/mmc/dw_mmc.c: In function ‘dwmci_set_idma_desc’:
drivers/mmc/dw_mmc.c:43:20: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
desc->next_addr = (unsigned int)desc + sizeof(struct dwmci_idmac);
^
drivers/mmc/dw_mmc.c: In function ‘dwmci_prepare_data’:
drivers/mmc/dw_mmc.c:61:35: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
dwmci_writel(host, DWMCI_DBADDR, (unsigned int)cur_idmac);
^
drivers/mmc/dw_mmc.c:73:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
(u32)bounce_buffer + (i * PAGE_SIZE));
^
CC drivers/mmc/hi6220_dw_mmc.o
drivers/mmc/hi6220_dw_mmc.c: In function ‘hi6220_dwmci_add_port’:
drivers/mmc/hi6220_dw_mmc.c:51:17: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
host->ioaddr = (void *)regbase;
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Fix below compilation warnings-
drivers/gpio/hi6220_gpio.c: In function ‘hi6220_gpio_probe’:
drivers/gpio/hi6220_gpio.c:82:15: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
bank->base = (u8 *)plat->base;
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
short strings can be used in type parameter of gpt command
to replace the guid string for the types known by u-boot
partitions = name=boot,size=0x6bc00,type=data; \
name=root,size=0x7538ba00,type=linux;
gpt write mmc 0 $partitions
and they are also used to display the type of partition
in "part list" command
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x0000037f "boot"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
type: data
guid: d117f98e-6f2c-d04b-a5b2-331a19f91cb2
2 0x00000380 0x003a9fdc "root"
attrs: 0x0000000000000000
type: 0fc63daf-8483-4772-8e79-3d69d8477de4
type: linux
guid: 25718777-d0ad-7443-9e60-02cb591c9737
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
code under flag CONFIG_PARTITION_TYPE_GUID
add parameter "type" to select partition type guid
example of use with gpt command :
partitions = uuid_disk=${uuid_gpt_disk}; \
name=boot,size=0x6bc00,uuid=${uuid_gpt_boot}; \
name=root,size=0x7538ba00,uuid=${uuid_gpt_root}, \
type=0fc63daf-8483-4772-8e79-3d69d8477de4;
gpt write mmc 0 $partitions
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Previously, Linux used the same GUID for the data partitions as Windows
(Basic data partition: EBD0A0A2-B9E5-4433-87C0-68B6B72699C7).
This created problems when dual-booting Linux and Windows in UEFI-GPT
Setup, so a new GUID (Linux filesystem data:
0FC63DAF-8483-4772-8E79-3D69D8477DE4) was defined jointly by GPT fdisk
and GNU Parted developers.
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
When converting between PCI bus and phys addresses, a two pass search
was introduced with preference to non-PCI_REGION_SYS_MEMORY regions.
See commit 2d43e873a2.
However, since PCI_REGION_MEM is defined as 0, the if statement was
always asserted true: ((flags & PCI_REGION_MEM) == PCI_REGION_MEM)
This patch uses PCI_REGION_TYPE bit to check if the region is
PCI_REGION_MEM: ((flags & PCI_REGION_TYPE) == PCI_REGION_MEM)
Signed-off-by: Cheng Gu <chenggu@marvell.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Condense these updates down to SPDX tags too while doing this. This is
a port of a1452a3771c4eb85bd779790b040efdc36f4274e from the Linux
Kernel.
Signed-off-by: Tom Rini <trini@konsulko.com>
On the BeagleBone these i2c1 pins are routed to the expanasion header, where
they can be defined as either pr1_usart0_Xxd/pwm0/spi0/i2c1, dont assume i2c1
Fixes: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/313894/1387696
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reported-by: Matthijs van Duin <matthijsvanduin@gmail.com>
CC: Tom Rini <trini@konsulko.com>
The Cubietruck has a mini-USB connector that can be used to power up the
board and as an OTG connector.
Since we have already some USB host-only ports right beside this one,
enable it in gadget mode
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A13-Olinuxino has a mini-USB connector that can be used to power up
the board and as an OTG connector.
Since we have already some USB host-only ports right beside this one,
enable it in gadget mode
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Android sparse image format is currently supported through a file
called aboot, which isn't really such a great name, since the sparse image
format is only used for transferring data with fastboot.
Rename the file and header to a file called "sparse", which also makes it
consistent with the header defining the image structures.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some devices might need to do some per-partition initialization
(ECC/Randomizer settings change for example) before actually accessing it.
Add some hooks before the write and erase operations to let the boards
define what they need to do if needed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
So far the fastboot code was only supporting MMC-backed devices for its
flashing operations (flash and erase).
Add a storage backend for NAND-backed devices.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The fastboot client will split the sparse images into several chunks if the
image that it tries to flash is bigger than what the device can handle.
In such a case, the bootloader is supposed to retain the last offset to
which it wrote to, so that it can resume the writes at the right offset
when flashing the next chunk.
Retain the last offset we used, and use the session ID to know if we need
it or not.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The fastboot flash command that writes an image to a partition works in
several steps:
1 - Retrieve the maximum size the device can download through the
"max-download-size" variable
2 - Retrieve the partition type through the "partition-type:%s" variable,
that indicates whether or not the partition needs to be erased (even
though the fastboot client has minimal support for that)
3a - If the image is smaller than what the device can handle, send the image
and flash it.
3b - If the image is larger than what the device can handle, create a
sparse image, and split it in several chunks that would fit. Send the
chunk, flash it, repeat until we have no more data to send.
However, in the 3b case, the subsequent transfers have no particular
identifiers, the protocol just assumes that you would resume the writes
where you left it.
While doing so works well, it also means that flashing two subsequent
images on the same partition (for example because the user made a mistake)
would not work withouth flashing another partition or rebooting the board,
which is not really intuitive.
Since we have always the same pattern, we can however maintain a counter
that will be reset every time the client will retrieve max-download-size,
and incremented after each buffer will be flashed, that will allow us to
tell whether we should simply resume the flashing where we were, or start
back at the beginning of the partition.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The current sparse image parser relies heavily on the MMC layer, and
doesn't allow any other kind of storage medium to be used.
Rework the parser to support any kind of storage medium, as long as there
is an implementation for it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The functions and a few define to generate a fastboot message to be sent
back to the host were so far duplicated among the users.
Move them all to a common place.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
To check the alignment of the image blocks to the storage blocks, the
current code uses a convoluted syntax, while a simple mod also does the
work.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The chunk parsing code was duplicating a lot of code among the various
chunk types, while all of them could be covered by generic and simple
functions.
Refactor the current code to reuse as much code as possible and hopefully
make the chunk parsing loop more readable and concise.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The current sparse image format parser is quite tangled, with a lot of
code duplication.
Start refactoring it by moving the header parsing function to a function
of its own.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The current error message in get_part if CONFIG_MTDPARTS is disabled is
"offset is not a number" which is confusing and doesn't help at all.
Change that for something that might give a hint on what's going on.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since we don't have for sure a valid IP-setup during
board_late_init(...) because it maybe allready stored in environment or
not, we cannot form a proper vxWorks bootline at this place.
So we move to the way, forming the bootline just before
executing/launching vxWorks. To do this we use the bootvx command
instead go.
We only have to form the "othbootargs" environment variable, the rest is
done pretty good by the "bootvx" commannd.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Support LCDIF for mx7dsabresd board:
1. Add pinmux settings
2. Add VIDEO related macro definition and videomode env settings.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Compile misc.c for mx7, since we need related function for
lcdif and nand.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Need to call lcdif_power_down to make lcdif in initial state
before kernel boot. Similar issue for uboot reset with lcdif
enabled, system will hang after serveral times resetting. Need
to let lcdif initial state to make all go well.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
We need to power down lcdif before uboot reset to make reset can pass
stress test.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
