This adds a driver for the FAN53555 family of regulators and wraps it
in a PMIC implementation.
While these devices support a 'normal' and 'suspend' mode (controlled
via an external pin) to switch between two programmable voltages, this
incarnation of the driver assumes that the device is always operating
in 'normal' mode.
Only setting/reading the programmed voltage is supported at this time
and the following device functionality remains unsupported:
- switching the selected voltage (via a GPIO)
- disabling the voltage output via software-control
This matches the functionality of the Linux driver.
Tested on a RK3399-Q7 (with 'option 5' devices): setting voltages from
the U-Boot shell and verifying output voltages on the board.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Add u-boot,off-on-delay-us for fixed regulator.
Depends on board design, the gpio regulator sometimes
connects with a big capacitance. When need to off, then
on the regulator, if there is no enough delay,
the voltage does not drop to 0, so introduce this
property to handle such case.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add regulator driver for STM32 voltage reference buffer which can be
used as voltage reference for ADCs, DACs and external components through
dedicated VREF+ pin.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch extends pmic_bind_children prefix matching. In addition to
the node name the property regulator-name is used while trying to match
prefixes. This allows assigning different drivers to regulator nodes
named regulator@1 and regulator@10 for example.
I have discarded the idea of using other properties then regulator-name
as I do not see any benefit in using property compatible or even
regulator-compatible. Of course I am open to change this if there are
good reasons to do so.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Simon Glass <sjg@chromium.org>
The regulator bindings state that regulator prefixes are allowd to be
in upper or lower case. However pmic_bind_children from pmic_uclass uses
strncmp to compare DT node name against prefix. This comparison is case
sensitive hence the regulator driver prefix case matters.
Signed-off-by: Felix Brack <fb@ltec.ch>
Add support to handle enable-active-high DT property. This property is
used to drive the gpio controlling fixed regulator as active high when
claiming gpio line.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
When enabling a fixed regulator, it may take some time to rise to the
correct voltage. If we do not delay here then subsequent operations
will fail.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We do not need that "regulator-name" property must be provided in dts.
If "regulator-name" property is not provided in dts, node name
will chosen for settings '.name' field of uc_pdata.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
This commit adds emulation of sandbox PMIC device, which includes:
- PMIC I2C emulation driver
- PMIC I/O driver (UCLASS_PMIC)
- PMIC regulator driver (UCLASS_REGULATOR)
The sandbox PMIC has 12 significant registers and 4 as padding to 16 bytes,
which allows using 'i2c md' command with the default count (16).
The sandbox PMIC provides regulators:
- 2x BUCK
- 2x LDO
Each, with adjustable output:
- Enable state
- Voltage
- Current limit (LDO1/BUCK1 only)
- Operation mode (different for BUCK and LDO)
Each attribute has it's own register, beside the enable state, which depends
on operation mode.
The header file: sandbox_pmic.h includes PMIC's default register values,
which are set on i2c pmic emul driver's probe() method.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested on sandbox:
Tested-by: Simon Glass <sjg@chromium.org>
This driver implements regulator operations for fixed Voltage/Current
value regulators. beside the standard regulator constraints, which are
put into the uclass platform data, a typical fixed regulator node provides
few additional properties like:
- gpio
- gpio-open-drain
- enable-active-high
- startup-delay-us
The only 'gpio' is used by this driver and is kept in structure of type
'fixed_regulator_platdata', as a device platform data (dev->platdata).
The driver implements:
- get_value
- get_current
- get_enable
- set_enable
The regulator calls and commands can be used for fixed-regulator devices,
and the proper error will be returned for prohibited.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds support to MAX77686 regulator driver,
based on a driver model regulator's API. It implements
almost all regulator operations, beside those for setting
and geting the Current value.
For proper bind and operation it requires the MAX77686 PMIC driver.
New file: drivers/power/regulator/max77686.c
New config: CONFIG_DM_REGULATOR_MAX77686
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit introduces the implementation of dm regulator API.
Device tree support allows for auto binding. And by the basic
uclass operations, it allows to driving the devices in a common
way. For detailed informations, please look into the header file.
Core files:
- drivers/power/regulator-uclass.c - provides regulator common functions api
- include/power/regulator.h - define all structures required by the regulator
Changes:
- new uclass-id: UCLASS_REGULATOR
- new config: CONFIG_DM_REGULATOR
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This adds driver support for the TPS65090 PMU. Support includes
hooking into the pmic infrastructure so that the pmic commands
can be used on the console. The TPS65090 supports the following
functionality:
- fet enable/disable/querying
- getting and setting of charge state
Even though it is connected to the pmic infrastructure it does
not hook into the pmic charging charging infrastructure.
The device tree binding is from Linux, but only a small subset of
functionality is supported.
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Katie Roberts-Hoffman <katierh@chromium.org>
Signed-off-by: Rong Chang <rongchang@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
