Commit graph

16 commits

Author SHA1 Message Date
Masahiro Yamada
c21f58548c ARM: uniphier: deassert RST_n of eMMC device for LD11/LD20
For LD11 and LD20 SoCs, the RST_n pin is asserted by default.  If
the EXT_CSD[162], bit[1:0] (RST_n_ENABLE) is fused, the eMMC device
would stay in the reset state until its RST_n pin is deasserted by
software.

Currently, this is cared by an ad-hoc way because the eMMC hardware
reset provider is not supported in U-Boot for now.  This code should
be re-written once the "mmc-pwrseq-emmc" binding is supported.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-23 08:37:56 +09:00
Masahiro Yamada
2c2ab3d495 ARM: uniphier: add PXs3 SoC support
Initial support for PXs3 SoC.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-22 16:49:34 +09:00
Masahiro Yamada
ee8ef5afa8 ARM: uniphier: add macro to generate SoC data look-up function
There are similar functions that look up SoC data by the SoC ID.
The new macro UNIPHIER_DEFINE_SOCDATA_FUNC will be helpful to
avoid the code duplication.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-22 16:49:33 +09:00
Masahiro Yamada
e27d6c7d32 ARM: uniphier: simplify SoC ID get function
Currently, uniphier_get_soc_type() converts the SoC ID (this is
read from the revision register) to an enum symbol to use it for SoC
identification.  Come to think of it, there is no need for the
conversion in the first place.  Using the SoC ID from the register
as-is a straightforward way.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-22 16:49:27 +09:00
Masahiro Yamada
561ca649a8 ARM: uniphier: make SPL optional for ARVv8 SoCs
We may want to run different firmware before running U-Boot.  For
example, ARM Trusted Firmware runs before U-Boot, making U-Boot
a non-secure world boot loader.  In this case, the SoC might be
initialized there, which enables us to skip SPL entirely.

This commit removes "select SPL" to make it configurable.  This
also enables the Multi SoC support for the UniPhier ARMv8 SoCs.
(CONFIG_ARCH_UNIPHIER_V8_MULTI)  Thanks to the driver model and
Device Tree, the U-Boot proper part is now written in a generic way.
The board/SoC parameters reside in DT.  The Multi SoC support
increases the memory footprint a bit, but the U-Boot proper does
not have strict memory constraint.  This will mitigate the per-SoC
(sometimes per-board) defconfig burden.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-22 15:11:12 +09:00
Masahiro Yamada
7a37bd64c5 ARM: uniphier: add missing static and const qualifier
These are file-internal and constant.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-22 15:01:27 +09:00
Masahiro Yamada
26b09c022a ARM: uniphier: move SBC and Support Card init code to U-Boot proper
Initialize SBC and Support Card in U-Boot proper instead of SPL.

We may run different firmware (ex. ARM Trusted Firmware) before
U-Boot, and basic SoC initialization may be done there.  In that
case, SPL may not be used.

The motivation for preparing SBC and Support Card in SPL was to use
LED for early debugging, but this is not mandatory to boot SoCs.
With this commit, LED will be unavailable in SPL, but we can use a
debug serial instead.  So, this change will not be a big deal.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-18 01:22:30 +09:00
Masahiro Yamada
b61664e230 ARM: uniphier: refactor board_init()
The code here is cluttered due to the switch statement.  Introduce a
table of callbacks to clean up the initialization code across SoCs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-18 01:22:30 +09:00
Masahiro Yamada
a314a245d1 ARM: uniphier: remove unneeded argument of uniphier_ld20_pll_init()
At first, we thought the LD20 PLL setting would be board dependent,
but this argument turned out unneeded after all.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-17 09:00:40 +09:00
Masahiro Yamada
baaafaaad3 ARM: uniphier: add work-around for VBO noise problem
Raise the VDD09 voltage line to 1.0V to suppress VBO noise.
This errata work-around code is needed only for ES1.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-10-10 10:03:23 +09:00
Masahiro Yamada
c72f4d4c2e ARM: uniphier: add PLL init code for LD11 SoC
- Initialize PLLs (SPL initializes only DPLL to save the precious
   SPL memory footprint)
 - Adjust CPLL/MPLL to the final tape-out frequency
 - Set the Cortex-A53 clock to the maximum frequency since it is
   running at 500MHz (SPLL/4) on startup

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-23 01:00:23 +09:00
Masahiro Yamada
682e09ff9f ARM: uniphier: add PLL init code for LD20 SoC
Initialize the DPLL (PLL for DRAM) in SPL, and others in U-Boot
proper.  Split the common code into pll-base-ld20.c for easier
re-use.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-19 00:12:26 +09:00
Masahiro Yamada
6a3e4274e4 ARM: uniphier: move PLL init code to U-Boot proper where possible
The PLL for the DRAM interface must be initialized in SPL, but the
others can be delayed until U-Boot proper.  Move them from SPL to
U-Boot proper to save the precious SPL memory footprint.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-19 00:06:44 +09:00
Masahiro Yamada
b78ffc53c5 ARM: uniphier: move XIRQ pin-mux settings of LD11/LD20
This is the last code in the mach-uniphier/pinctrl/ directory.
Push the remaining code out to delete the directory entirely.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18 23:47:27 +09:00
Masahiro Yamada
5ac9dfbe9d ARM: uniphier: consolidate NAND pin-mux settings
The NAND subsystem has not supported the Driver Model yet, but the
NAND pin-mux data are already in the pinctrl drivers.  Use them by
calling pinctrl_generic_set_state() directly.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18 23:10:44 +09:00
Masahiro Yamada
b291671232 ARM: uniphier: merge board init functions into board_init()
Currently, the UniPhier platform calls several init functions in the
following order:

  [1] spl_board_init()
  [2] board_early_init_f()
  [3] board_init()
  [4] board_early_init_r()
  [5] board_late_init()

The serial console is not ready at the point of [2], so we want to
avoid using [2] from the view point of debuggability.  Fortunately,
all of the initialization in [2] can be delayed until [3].  I see no
good reason to split into [3] and [4].  So, merge [2] through [4].

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-14 22:54:20 +09:00
Renamed from arch/arm/mach-uniphier/board_early_init_f.c (Browse further)