When MACB_ZYNQ is enabled there is compilation warnings
drivers/net/macb.c: In function ‘_macb_init’:
drivers/net/macb.h:675:33: error: ‘MACB_DMACFG’ undeclared (first use in this function);
did you mean ‘MACB_MCF’?
writel((value), (port)->regs + MACB_##reg)
^~~~~
It has been caused by changing macros name by commit below.
Fixes: 6c636514d4 ("net: macb: sync header definitions as taken from Linux")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The implementation of dma_map_single() and dma_unmap_single() is
exactly the same for all the architectures that support them.
Factor them out to <linux/dma-mapping.h>, and make all drivers to
include <linux/dma-mapping.h> instead of <asm/dma-mapping.h>.
If we need to differentiate them for some architectures, we can
move the generic definitions to <asm-generic/dma-mapping.h>.
Add some comments to the helpers. The concept is quite similar to
the DMA-API of Linux kernel. Drivers are agnostic about what is
going on behind the scene. Just call dma_map_single() before the
DMA, and dma_unmap_single() after it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now that arch specific dma mapping APIs take care of cache
flush/invalidate, drop local cache flush operation.
While at that fix dma_unmap_single() call to match new prototype
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This allows passing arbitrary addresses through macb_miiphy_read and
macb_miiphy_write, therefore enabling the mii command to access
all mdio bus devices instead of only the defined phy.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To support accessing arbitrary addresses the mii/mdio bus it is
necessary that the macb_mdio_read and macb_mdio_write functions
do not implicitly use the address of the connected phy.
The function signature is extended according to the Linux kernel
equivalent.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With commit c6d07bf440 ("net/macb: increase RX buffer size for GEM")
ethernet support does not work any more with d-cache enabled on the
AT91SAM. The reason is, that MACB_RX_BUFFER_SIZE was changed from 4096
to 128 but this change was not refected in the rx_buffer flush and
invalidate functions, as these also use this macro.
This patch now fixes this by calculating the rx buffer size correctly
again in those functions. With this change, ethernet works again
reliably on my AT91SAM board.
Signed-off-by: Stefan Roese <sr@denx.de>
Fixes: c6d07bf440 ("net/macb: increase RX buffer size for GEM")
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Anup Patel <anup.patel@wdc.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This reverts commit 1b0c9914cc.
Commit 1b0c9914cc ("net: macb: Fixed reading MII_LPA register")
causes 100Mbps does not work any more with SiFive FU540 GEM on the
HiFive Unleashed board. Revert it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Instead of depending on CONFIG_SYS_LITTLE_ENDIAN, we check at runtime
whether underlying system is little-endian or big-endian. This way
we are not dependent on any U-Boot specific OR compiler specific macro
to check system endianness.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The SiFive MACB ethernet has a custom TX_CLK_SEL register to select
different TX clock for 1000mbps vs 10/100mbps.
This patch adds SiFive MACB compatible string and extends the MACB
ethernet driver to change TX clock using TX_CLK_SEL register for
SiFive MACB.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Macb Ethernet controller requires a RX buffer of 128 bytes. It is
highly sub-optimal for Gigabit-capable GEM that is able to use
a bigger DMA buffer. Change this constant and associated macros
with data stored in the private structure.
RX DMA buffer size has to be multiple of 64 bytes as indicated in
DMA Configuration Register specification.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
DMA configuration was heavily dependent on the HW
defaults, add function to properly set the required
fields, including the new dma_burst_length.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
GEM support higher DMA burst writes/reads than the default (4).
add configuration structure with dma burst length so it could be
applied later to DMA configuration.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds support for the sgmii phy interface,
available only to DM users, dictated by current driver
design.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
macb.h provides macros for reading/setting bitfields,
in macb registers and descriptors. use that instead
of redefining them in the source file.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
add support for clock rates higher than 2.4Mhz
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Few registers and bits were added by Cadence and
they were not updated in the headers.
Take the latest definitions as defined in Linux
header (5.1) that also includes some comments
about existing registers.
One register was improperly named (UR), fix that.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Macb can be used with Xilinx PCS/PMA PHY in fpga which is a 1000-baseX
phy(lpa 0x41e0). This patch adds checks for LPA_1000XFULL and
LPA_1000XHALF bits.
Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If macb is gem and is gigabit capable, lpa value is not read from
the right register(MII_LPA) and is read from MII_STAT1000. This patch
fixes reading of the lpa value.
Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
At present the link speed change callback is a nop. According to
macb device tree bindings, an optional "tx_clk" is used to clock
the ethernet controller's TX_CLK under different link speed.
In 10/100 MII mode, transmit logic must be clocked from a free
running clock generated by the external PHY. In gigabit GMII mode,
the controller, not the external PHY, must generate the 125 MHz
transmit clock towards the PHY.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This updates DM version macb_linkspd_cb() signature for future
expansion, eg: adding an implementation for link speed changes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
I've noticed that the first ethernet packet after PHY link establishment
is not tranferred correctly most of the time on my AT91SAM9G25 board.
Here I usually see a timeout of a few seconds, which is quite
annoying.
Adding a small delay (10ms in this case) after the link establishment
helps to solve this problem. With this patch applied, this timeout
on the first packet is not seen any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix MID bit field check to correctly identify all GEM hardwares.
The check is updated as per macb driver in Linux location:
<linux_sources>/drivers/net/ethernet/cadence/macb_main.c:259
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Don't fail in macb_enable_clk() if clk_enable() returns
-ENOSYS because we get -ENOSYS for fixed-rate clocks.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
In
if (a > =0) {...}
else (a < 0) {...}
the second logical constraint is superfluous.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Although Xilinx Zynq SoC was using MACB similar hardware. However,
U-boot MACB driver was not supporting Xilinx Zynq SoC. This patch is
to add support for the Xilinx Zynq SoC to the existing MACB network
driver.
This patch is to add Zynq GEM DMA Config, provide callback
function for different linkspeed for case of using Xilinx Zynq
Programmable Logic as GMII to RGMII converter.
This patch convert the return value to use error codes.
Signed-off-by: Wilson Lee <wilson.lee@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
Cc: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Always search the PHY to determine the macb->phy_addr before using
the PHY to fix "No PHY present" error.
Fix the wrong test of the GMAC's phy interface mode, it should be
PHY_INTERFACE_MODE_RGMII.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
To avoid the failure of mdio_register(), add the remove callback
to unregister the mii_dev when removing the ethernet device.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fixed up unused variable warning, e.g. for gurnard:
Signed-off-by: Simon Glass <sjg@chromium.org>
For the boards such as smartweb on which the clock driver isn't
supported, the ethernet fail to be found when booting up with
the below log.
---8<---
Net: No ethernet found.
--->8---
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove the redundant #ifdef CONFIG_DM_ETH/#endif.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Due to introducing the at91 clock driver, add the clock support.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
when using tftp on the smartweb board, it prints a lot of
CACHE: Misaligned operation at range [23b2e000, 23b2e100]
warnings ... fixed them.
Signed-off-by: Heiko Schocher <hs@denx.de>
Now, include/linux/errno.h is a wrapper of <asm-generic/errno.h>.
Replace all include directives for <asm-generic/errno.h> with
<linux/errno.h>.
<asm-generic/...> is supposed to be included from <asm/...> when
arch-headers fall back into generic implementation. Generally, they
should not be directly included from .c files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add drivers/usb/host/xhci-rockchip.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Run scripts/coccinelle/net/mdio_register.cocci on the U-Boot code base.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use the right phy_connect() prototype for CONFIGF_DM_ETH.
Support to get the phy interface from dt and set GMAC_UR.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add driver-model support to this driver. The old code remains for now so
that we can convert boards one at a time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
The end address of the cache flush must be cache-line-aligned since
otherwise (at least on ARM926-EJS) the request is ignored. When the cache
is enabled this means that packets are not sent.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Adjust this driver to avoid using struct netdev in functions that driver
model will call. Also refactor the receive function to be compatible with
driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
During the initialization of PHY the gigabit bit capable is set if the
controller is a GEM. However, for sama5d2 and sama5d4, the GEM is
configured to support only 10/100.
Improperly setting the GBE capability leads to an unresponsive MAC
controller. This patch fixes this behavior allowing using the gmac with
these SoCs.
Suggested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
[fixed minor checkpatch warning]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
