Commit graph

10 commits

Author SHA1 Message Date
pekon gupta
e53ad4b445 board/ti/am43xx: add support for parallel NAND
This patch adds support for NAND device connected to GPMC chip-select on
following AM43xx EVM boards.

am437x-gp-evm: On this board, NAND Flash signals are muxed with eMMC, thus at a
  time either eMMC or NAND can be enabled. Selection between eMMC and NAND is
  controlled by:
  (a) Statically using Jumper on connecter (J89) present on board.
  (a) If Jumper on J89 is NOT used, then selection can be dynamically controlled
      by driving SPI2_CS0[MUX_MODE=GPIO] pin via software:
      SPI2_CS0 == 0: NAND (default)
      SPI2_CS0 == 1: eMMC

am43x-epos-evm: On this board, NAND Flash control lines are muxed with QSPI,
  Thus only one of the two can be used at a time. Selection is controlled by:
  (a) Dynamically driving following GPIO pin from software
      GPMC_A0(GPIO) == 0 NAND is selected (default)

NAND device (MT29F4G08AB) on these boards has:
 - data-width=8bits
 - blocksize=256KB
 - pagesize=4KB
 - oobsize=224 bytes
For above NAND device, ROM code expects the boot-loader to be flashed in BCH16
ECC scheme for NAND boot, So by default BCH16 ECC is enabled for AM43xx EVMs.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-08-25 10:48:12 -04:00
Felipe Balbi
403edbb94f board: ti: am43xx: enable QSPI and Gbit Ethernet on AM437x SK
AM437x Starter Kit has a qspi flash and gbit ethernet
support. By muxing those signals, we can use those
interfaces from u-boot.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-06-19 17:53:58 -04:00
Mugunthan V N
4cdd7fda91 ARM: AM43xx: Add CPSW support to AM43xx EPOS and GP EVM
Adding support for CPSW to AM43xx EPOS nad GP EVM which is connected
to RMII and RGMII phy respectively and enable cpsw in config.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-03-04 09:42:06 -05:00
Tom Rini
eeb72e6761 Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	arch/arm/cpu/armv7/config.mk
	board/ti/am43xx/mux.c
	include/configs/am43xx_evm.h

Signed-off-by: Tom Rini <trini@ti.com>
2014-02-26 16:49:58 -05:00
Dave Gerlach
cd8341b7eb ARM: AM43xx: GP-EVM: Correct GPIO used for VTT regulator control
Schematic indicates GPIO5_7 is to be used for VTT regulator control
rather than GPIO0_21 so modify enable_vtt_regulator to reflect this.
Without this some boards will experience DDR3 corruption and fail to
boot.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[trini: Rework patch against mainline]
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21 13:55:40 -05:00
Sourav Poddar
ea4c7a8321 am437x_epos_evm: add SPL API, QSPI, and serial flash support
Enables support for SPI SPL, QSPI and Spansion serial flash device
on the EVM. Configures pin muxes for QSPI mode.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-02-18 22:41:09 +05:30
Lokesh Vutla
b5e01eecc8 ARM: AM43xx: GP_EVM: Add support for DDR3
GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH).
Adding details for the same.
Below is the brief description of DDR3 init sequence(SW leveling):
-> Enable VTT regulator
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program leveling registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:45 -05:00
Lokesh Vutla
cf04d0326b ARM: AM43xx: clocks: Update DPLL details
Updating the Multiplier and Dividers value for all DPLLs.
Safest OPP is read from DEV ATTRIBUTE register. Accoring to the value
returned the MPU DPLL is locked.
At different OPPs follwoing are the MPU locked frequencies.
OPP50	300MHz
OPP100	600MHz
OPP120	720MHz
OPPTB	800MHz
OPPNT	1000MHz
According to the latest DM following is the OPP table dependencies:
	VDD_CORE 	VDD_MPU
	OPP50		OPP50
	OPP50 		OPP100
	OPP100		OPP50
	OPP100		OPP100
	OPP100		OPP120
So at different OPPs of MPU it is safest to lock CORE at OPP_NOM.
Following are the DPLL locking frequencies at OPP NOM:
Core locks at 1000MHz
Per locks at 960MHz
LPDDR2 locks at 266MHz
DDR3 locks at 400MHz

Touching AM33xx files also to get DPLL values specific to board but no
functionality difference.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:01 -05:00
Lokesh Vutla
4892495e36 ARM: AM43xx: mux: Update mux data
Updating the mux data for UART, adding data for i2c0 and mmc.
And also updating pad_signals structure.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:01 -05:00
Lokesh Vutla
fbf2728da3 ARM: AM43xx: Add Board files
Add board specific information for AM43xx.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15 08:51:10 -04:00