After the conversion to DM_PMIC the following output is seen:
PMIC: PMIC: PFUZE100 ID=0x10
Remove the unnecessary PMIC string from the board file to
avoid the repetead string.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Commit ec837c82d7 ("imx6: wandboard: convert to DM_PMIC")
caused the following pmic_get() error:
CPU: Freescale i.MX6QP rev1.0 at 792 MHz
Reset cause: POR
DRAM: 2 GiB
PMIC: pmic_get() ret -19
...
and since the PMIC presence is used to determine the board D1 revision,
the following error is seen when booting a board rev D1:
WARNING: Could not determine dtb to use
and the kernel does not boot at all.
Fix the regression by passing "pfuze100@8" as the correct parameter
to the pmic_get() function in the DM case.
Fixes: ec837c82d7 ("imx6: wandboard: convert to DM_PMIC")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
After the transition to DM, only the mx6dl/solo wandboard
is supported.
Add FIT image support so that all the wandboard variants
can be supported, like it was prior to the DM conversion.
Successfully booted Linux on mx6q/solo/qp wandboards.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
When using DM_I2C the speed value supplied to setup_i2c() is not used,
so this code required CONFIG_SYS_MXC_I2C[12]_SPEED to be defined to
compile, but did not actually use them.
Change this so we no longer need to define an unused macro to compile in
DM_I2C mode. Also make it more clear that they do not control the bus
speed. Otherwise it is quite easy to mistakenly believe they are used
to set the bus speed.
Cc: Heiko Schocher <hs@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
No definition provided by input.h is used in the board file.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Inside setup_sata() there is a cpu type check, so there is no need to
do this check in the board file.
This also brings the benefit to allowing setup_sata() to be called for the
mx6qp wandboard variant.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add support for the latest MX6QP wandboard variant.
Based on Richard Hu's work from Technexion's U-Boot tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Latest wandboard hardware revision is revd1, which brings the following
new features:
- PFUZE100 PMIC
- AR8035 Ethernet PHY
- Upgrade Wifi/BT chip to BCM4339/BCM43430.
The detection mechanism is to probe the PMIC and when it is
found, then the revision of the board is revd1.
As the detection is done via PMIC, we need to print the board version
at a later stage via CONFIG_DISPLAY_BOARDINFO_LATE and also need
to disable CONFIG_DISPLAY_BOARDINFO, which is done much earlier.
Make the necessary adjustments for the AR8035 PHY to work on revd1.
Based on Richard Hu's work from Technexion's U-Boot tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
There is no need call setup_display() from SPL code, so move it to
board_init(), which executes only in U-Boot proper.
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
At present CONFIG_CMD_SATA enables the 'sata' command which also brings
in SATA support. Some boards may wish to enable SATA without the command.
Add a separate CONFIG to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When I tried to deactivate VIDEO support for the Wandboard, it still
tried to initialize the Framebuffer and so on. That is the reason for
the added ifdefs. CONFIG_VIDEO is enabled in the configuration as default
and therefore nothing changes for the default user.
The structs mx6dl_i2c2_pad_info and mx6q_i2c2_pad_info are only available
when CONFIG_IPUV3 are set and should not be tried to access, when that
define is not defined.
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Since commit ce412b79e7 ("drivers: net: phy: atheros: add separate
config for AR8031") ethernet does not work on mx6sabresd.
This commit correctly assigns ar8031_config() as the configuration
function for AR8031 in the same way as done in the Linux kernel.
However, on wandboard design we need some additional configuration,
such as enabling the 125 MHz AR8031 output that needs to be done
in the board file.
This also aligns with the same method that the kernel performs
the AR8031 fixup in arch/arm/mach-imx/mach-imx6q.c.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
It's not necessary to use the is_cpu_type function, there is a macro in
sys_proto.h already implemented.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
As per the AR8031 datasheet:
"For a reliable power on reset, suggest to keep asserting the reset
low long enough (10ms) to ensure the clock is stable and clock-to-reset
1ms requirement is satisfied."
So do as suggested and also add a 100us delay after deasserting the
reset line to guarantee that the PHY ID can be read correctly and the
Atheros 8031 PHY driver can be loaded automatically.
This results in a simpler code.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There are two revisions of wandboard: version B1 and C1.
Add the revision detection support, so that the correct dtb file can
be automatically loaded.
Based on the patch from Richard Hu <hakahu@gmail.com>.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-By: Vagrant Cascadian <vagrant@aikidev.net>
Currently we need to build one U-boot image for each of the wandboard
variants: quad, dual-lite and solo.
By switching to SPL we can support all these variants with a single binary,
which is very convenient.
Based on the work from Richard Hu.
Tested kernel booting on the three boards.
Signed-off-by: Richard Hu <hakahu@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Vagrant Cascadian <vagrant@aikidev.net>
Reviewed-by: Stefano Babic <sbabic@denx.de>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This adds support for the 7" WVGA produced by Future Eletronics and
make it dynamically detect if it is connected or not based on the
touchscreen controller.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
Include <input.h> in order to fix the following sparse warning:
wandboard.c:278:5: warning: symbol 'overwrite_console' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add a prototype for board_phy_config() to fix the following sparse warning:
wandboard.c:200:5: warning: symbol 'board_phy_config' was not declared. Should it be static?
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fix the following sparse warning:
wandboard.c:58:22: warning: symbol 'usdhc1_pads' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.
In order to simplify the code, just return the value from cpu_eth_init(bis)
directly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Instead of duplicating HDMI setup code for every mx6 board, factor out the common code
Signed-off-by: Pardeep Kumar Singla <b45784@freescale.com>
Acked-By: Eric Nelson <eric.nelson@boundarydevices.com>
Add support for the Quad version of Wandboard; fix compile warning resulting
from having 2G of memory.
Signed-off-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
PUE requires PKE to mean something, as do pull values with PUE, so do not
compell users to explicitly use PKE and PUE everywhere. This is also what is
done on Linux and what has already been done for i.MX51.
By the way, remove some unused pad control definitions.
There is no change of behavior.
Note that SPI_PAD_CTRL was defined by several boards with a pull value, but
without PKE or PUE, which means that no pull was actually enabled in the pad.
This might be a bug in those boards, but this patch does not change the
behavior, so it just removes the meaningless pull value from those definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Adds support for 'bmode' command which let user to choose where to
boot from; this allows U-Boot to load system from another storage
without messing with jumpers.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Allow use of the carrier board MicroSD card available in the
Wandboard; this allow for loading alternative system from the other
card for testing or upgrade proposes.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This add support to identify if the card is connected or not; so it
does not try to communicate with the controller if no card is
available.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
When booting a Freescale kernel 3.0.35 on a Wandboard solo, the get_board_rev()
returns 0x62xxx, which is not a value understood by the VPU
(Video Processing Unit) library in the kernel and causes the video playback to
fail.
The expected values for get_board_rev are:
0x63xxx: For mx6quad/dual
0x61xxx: For mx6dual-lite/solo
So adjust get_board_rev() accordingly and make it as weak function, so that we
do not need to define it in every mx6 board file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
