Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Supported boot device types in iMX8MN: MMC, DHCP.
Add DISTRO_DEFAULTS config option and include the distro boot command
header file to enable full support of distro boot on i.MX8M Nano EVK (both
DDR and LPDDR derivatives).
Drop previous environment, which was targeting customized boot commands and
boot order.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently it is not possible to boot Linux from the SD card
by default.
Make the necessary adjustments to allow it.
Reported-by: Peter Bergin <peter@berginkonsult.se>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrey Zhizhikin <andrey.z@gmail.com> # imx8mn_ddr4_evk
Reviewed-by: Peng Fan <peng.fan@nxp.com>
use CONFIG_TARGET_IMX8MN_DDR4_EVK for DDR4 EVK board, we will use
CONFIG_TARGET_IMX8MN_EVK for LPDDR4 EVK board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8M series includes support for high speed modes in uSDHC controllers.
Turn on corresponding configuration options for EVK boards, which would
enable high speed modes to be included in U-Boot.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently watchdog driver is not selected, which causes system to reboot
after staying 60s in the U-Boot prompt.
Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
It is safe to run SPL with caches enabled on i.MX8, so
remove such restriction.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Oliver Graute <oliver.graute@kococonnector.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
enable CONFIG_CMD_ERASEENV to make it easy to erase env.
Use savedefconfig to generate new defconfig.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
