Commit graph

1653 commits

Author SHA1 Message Date
Fabrice Gasnier
7fd9f31c6b usb: dwc2: fix gadget disconnect
This fixes a disconnect issue detected with fastboot command, when using
dwc2 driver.
- On u-boot side:
uboot>$ fastboot 0
- On USB host PC side, few seconds after
PC>$ fastboot reboot # Get stuck, uboot target never reboots

By enabling DEBUG_ISR logs, the bus suspend interrupt is seen before the
PC command has been issued. When the USB bus suspend occurs, there's a HACK
that disables the fastboot (composite driver). Here is the call stack
upon USB bus suspend:
- dwc2_handle_usb_suspend_intr()
  - dev->driver->disconnect()
    - composite_disconnect()
      - reset_config()
        - f->disable()
          - fastboot_disable()
            - usb_ep_disable(f_fb->out_ep);
            - usb_ep_disable(f_fb->in_ep);
            .. other disable calls.

When the resume interrupt happens, everything has been disabled, then
nothing happens. fastboot command gets stuck on HOST side.

Remove original HACK, that disconnects the composite driver upon
USB bus suspend. Implement disconnect detection instead:
- check GINTSTS OTG interrupt
- read GOTGINT register
- check GOTGINT, SesEndDet bit (e.g. session end)
This is inspired by what is implemented currently in Linux dwc2 driver.

Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2019-04-21 10:26:52 +02:00
Patrick Delaunay
6fe7dd3327 stm32mp1: add stusb1600 support for DK1 and DK2 board
The DK1 and DK2 boards use the USB Type-C controller STUSB1600.
This patch updates:
- the device tree to add the I2C node in the DT
- the board stm32mp1 to probe this I2C device and use this controller
  to check cable detection.
- the DWC2 driver to support a new dt property
  "u-boot,force-b-session-valid" which forces B session and
  device mode; it is a workaround because the VBUS sensing and
  ID detection isn't available with stusb1600.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-21 10:26:52 +02:00
Patrick Delaunay
931e9d7aa7 usb: dwc2: add support for STM32MP1
Add compatible "st,stm32mp1-hsotg" and associated driver data to manage
the usb33d-supply and the ST specific register for VBus sensing.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
# Conflicts:
#	drivers/usb/gadget/dwc2_udc_otg.c
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-21 10:26:52 +02:00
Patrice Chotard
763bb106f6 usb: dwc2_udc_otg: Add tx_fifo_sz array support
All TX fifo size can be different, add tx_fifo_sz_array[]
into dwc2_plat_otg_data to be able to set them.

tx_fifo_sz_array[] is 17 Bytes long and can contains max 16
tx fifo size (synopsys IP supports max 16 IN endpoints).
First entry of tx_fifo_sz_array[] is the number of valid
fifo size the array contains.

In case of tx_fifo_sz_array[] doesn't contains the same
number of element than max hardware endpoint, display
a warning message.

Compatibility with board which doesn't use tx_fifo_sz_array[]
(Rockchip rk322x/rk3128/rv1108/rk3288/rk3036) is kept.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-21 10:26:52 +02:00
Patrick Delaunay
5bd97e8073 usb: dwc2_udc_otg: Read MAX_HW_ENDPOINT from HWCFG4 register
Some DWC2 ip variant doesn't use 16 hardware endpoint as hardcoded
in the driver. Bits INEps [29:26] of HWCFG4 register allows to get
this information.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-21 10:26:52 +02:00
Patrick Delaunay
2d76160f04 usb: dwc2: Add function for session B check
Add a new function to check the session B validity, to be use to check
cable connection.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-21 10:26:52 +02:00
Patrick Delaunay
0fdd0bc621 usb: dwc2: Add force-b-session-valid support
Handle "force-b-session-valid" property from DT.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-21 10:26:52 +02:00
Patrick Delaunay
c2c74f97af usb: dwc2: force reset assert before to probe the driver
Reset the hardware to be sure of the device state.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-21 10:26:52 +02:00
Patrick Delaunay
c791c8431c usb: dwc2: convert driver to DM_USB_GADGET
Minimal conversion to driver model by using the uclass
UCLASS_USB_GADGET_GENERIC based on:
- reset uclass
- clock uclass
- generic uclass.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-21 10:26:51 +02:00
Patrick Delaunay
a812d77617 usb: dwc2: remove unused variable regs_otg
Remove the global regs_otg variable.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-21 10:26:51 +02:00
Alex Kiernan
17982a2855 usb: Select USB_MUSB_DSPS with USB_MUSB_TI
USB_MUSB_TI requires USB_MUSB_DSPS, failing at link time if it's not
selected:

  drivers/usb/musb-new/built-in.o: In function `ti_musb_host_ofdata_to_platdata':
  drivers/usb/musb-new/ti-musb.c:193: undefined reference to `musb_dsps_ops'

or if OF_CONTROL is not selected:

  arch/arm/mach-omap2/built-in.o:(.data.usb0+0x24): undefined reference to `musb_dsps_ops'

Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2019-04-19 11:32:01 +02:00
Alex Kiernan
ad991472e7 configs: Migrate USB_MUSB_DISABLE_BULK_COMBINE_SPLIT to Kconfig
Migrate support for disable MUSB bulk split/combine to Kconfig

Green Travis build:

https://travis-ci.org/akiernan/u-boot/builds/519101867

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2019-04-19 11:31:58 +02:00
Marcel Ziswiler
20df4b570d configs: move CONFIG_USB_EHCI_VF to Kconfig
Move CONFIG_USB_EHCI_VF to drivers/usb/host/Kconfig and update the one
and only user thereof being colibri_vf.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13 20:30:09 +02:00
Adam Ford
69535b33bc usb: ehci-mx6: Use common code to extract dr_mode
There exists code in drivers/common/common.c to read the dr_mode
from the device tree.  This patch converts this driver to use that
function to initialize the driver.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-04-09 13:11:45 +02:00
Ismael Luceno Cortes
89aea23abb usb: host: Print device name when scanning
Drop the counter, it has no meaning other than being the order in which
the interface is found; the name assigned to the USB host controller
interface is a better indicator.

Example of the original output:
> USB0:   USB EHCI 1.10
> scanning bus 0 for devices... 2 USB Device(s) found
>        scanning usb for storage devices... 1 Storage Device(s) found

Patched output:
> Bus usb@ee080100: USB EHCI 1.10
> scanning bus usb@ee080100 for devices... 2 USB Device(s) found
>        scanning usb for storage devices... 1 Storage Device(s) found

Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
2019-04-09 13:11:45 +02:00
Jean-Jacques Hiblot
e81d9de531 usb: udc-uclass: Fixed problem when no alias is defined in DT
commit 801f1fa442 "dm: usb: udc: Use SEQ_ALIAS to index the USB gadget
ports" changed the way the udevice if found. It uses the alias to find
a udevice for a given USB port number. In the commit log it was stated
that if no alias is provided, the bind order will be used instead. However
it doesn't work. Fixing this by adding a call to uclass_get_device() if
uclass_get_device_by_seq() fails.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Vignesh R <vigneshr@ti.com>
2019-03-16 13:29:43 +01:00
Peter Robinson
747fed56d3 Kconfig: tegra: Migrate USB_EHCI_TEGRA
Migrate USB_EHCI_TEGRA from headers to Kconfig

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peter.Chubb@data61.csiro.au
Cc: Lucas Stach <dev@lynxeye.de>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Alban Bedel <alban.bedel@avionic-design.de>
Cc: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2019-02-20 09:01:44 -07:00
Abel Vesa
921208ebca usb: ehci-mx6: Make regulator DM_REGULATOR dependent
Do the regulator related work only if the build has the DM_REGULATOR.

Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-02-15 22:01:15 +01:00
Jean-Jacques Hiblot
1c1464c2b1 usb: ether: call _usb_eth_halt() if initialization fails
If the host does not respond in time, the initialization fails. However
the usb ether driver will still be registered. This will make
usb_gadget_probe_driver() fail the next time the initialization is
attempted because it cannot find an available UDC.

Fixing this by calling _usb_eth_halt() when the init fails.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
2019-02-01 09:09:40 -05:00
Andrew F. Davis
6536ca4d66 spl: Kconfig: Drop the _SUPPORT postfix from SPL_DFU
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
2019-01-26 08:13:54 -05:00
Tom Rini
d01806a8fc Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2019-01-24 15:30:48 -05:00
Chris Packham
67bb984249 net: remove CONFIG_MCAST_TFTP
No mainline board enables CONFIG_MCAST_TFTP and there have been
compilation issues with the code for some time. Additionally, it has a
potential buffer underrun issue (reported as a side note in
CVE-2018-18439).

Remove the multicast TFTP code but keep the driver API for the future
addition of IPv6.

Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-01-24 11:35:30 -06:00
Jagan Teki
543049ab59 usb: host: Drop [e-o]hci-sunxi drivers
Now Allwinner platform is all set to use Generic USB
controller drivers, so remove the legacy sunxi drivers.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-01-18 22:19:09 +05:30
Jagan Teki
29d280c88a sunxi: usb: Switch to Generic host controllers
Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.

So switch sunxi USB use EHCI and OHCI Generic controllers.

Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-01-18 22:19:09 +05:30
Jagan Teki
b9aa0a9332 musb-new: sunxi: Use CLK and RESET support
Now clock and reset drivers are available for respective
SoC's so use clk and reset ops on musb driver.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2019-01-18 22:19:09 +05:30
Jean-Jacques Hiblot
b3c518a882 dm: usb: gadget: Fix boot breakage on sunxi platforms
Fixes commit 0131162439 ("dm: usb: create a new UCLASS ID for USB gadget
devices")

The UCLASS_DRIVER for id UCLASS_USB_GADGET_GENERIC needs to be declared
even for platforms that do not enable DM_USB_GADGET. Otherwise the driver
for their usb peripheral controller fails to bind.

Reported-by: Priit Laes <plaes@plaes.org>
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Priit Laes <plaes@plaes.org>
Acked-by: Jagan Teki <jagan@openedev.com>
2019-01-10 18:53:03 +01:00
Jean-Jacques Hiblot
f811e9763f Kconfig: rename CONFIG_SPL_USB_GADGET_SUPPORT as CONFIG_SPL_USB_GADGET
The SPL option for USB gadget should be named after the option for u-boot
(CONFIG_USB_GADGET)

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-01-10 18:52:55 +01:00
Jean-Jacques Hiblot
801f1fa442 dm: usb: udc: Use SEQ_ALIAS to index the USB gadget ports
dfu, fastbot and other usb gadget commands take the USB port index as a
parameter. Currently this index is assigned in the order of the driver
bindings.
Changing this behavior using the SEQ_ALIAS feature. This option assign to
the device a SEQ number based on its alias (if it exists)

To use it we must set the DM_UC_FLAG_SEQ_ALIAS flag and follow the existing
naming convention: use "usb" for the name of the gadget UCLASS_DRIVER
(same as for the UCLASS_USB).

If no alias is provided, then the index falls back to the order in which
the bindings took place.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reported-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Tested-by: Sam Protsenko <semen.protsenko@linaro.org>
2019-01-10 18:52:51 +01:00
Ye Li
8c6cc71b40 usb: xhci-mem: Fix scratchpad array issue
After updating the value of dev_context_ptrs[0], we should flush this
from cache to memory. Otherwise the xhci controller won't use it.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2019-01-09 16:03:56 +01:00
Stefan Mavrodiev
46a3f27654 usb: musb-new: sunxi: Fix null pointer access
When the device is in peripheral mode there is no
struct usb_bus_priv allocated pointer, as the uclass driver
("usb_dev_generic") doesn't call per_device_auto_alloc_size.

This results in writing to the internal SDRAM at
	priv->desc_before_addr = true;

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
2018-12-14 17:59:10 +01:00
Siva Durga Prasad Paladugu
771e76515e usb: composite: Fix max packet size for USB3.0
For USB3.0, the max packetsize for GET_DESCRIPTOR should be
sent as exponent value for 2. This means for 512, max packet
size should be filled with 9(2^9=512). Also, fill the USB
version field with 3.0 if speed is negotiated to Superspeed.
This fixes the issue of DFU gadget download failure with
superspeed. Without this patch, the max packet size is
overflowed to zero as the bMaxPacketsize is of u8 and hence
host is not able to detect this device.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-12-14 17:59:10 +01:00
Jean-Jacques Hiblot
7d98dbcc3d usb: musb-new: Add support for DM_USB
Enable DM for USB peripheral in the musb-new driver.
Also make sure that the driver can be used in the SPL.
This implies that:
* the driver must work with and without the OF_CONTROL option. That
in turn, implies that the platform data can be passed in a struct
ti_musb_platdata or be read from the dtb
* usb.o is linked in the SPL if host support is enabled

Another change is that the driver does not fail to bind (and stop the boot
process) if one of the child driver does not bind. Reporting the error is
enough. This kind of error would appear if the port is configured in the
DTS but the driver is not activated in the config.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-12-14 17:59:10 +01:00
Jean-Jacques Hiblot
1594c75b3e usb: musb-new: Allow the diver not to use the set_phy_power() callback
The set_phy_power() callback is part of struct omap_musb_board_data. This
structure is part of the platform data passed to the musb-new driver. This
does not really fit with the Driver Model, so allow not to use struct
omap_musb_board_data to turn the phy on or off.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-12-14 17:59:10 +01:00
Jean-Jacques Hiblot
1ce5f1f933 dwc3-generic: Add support for the am437x
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-12-14 17:59:09 +01:00
Jean-Jacques Hiblot
4dd76d0f96 usb: host: replace xhci-keystone driver by the generic dwc3 driver
The keystone platforms can use the generic DC3 driver. Removing the
keystone-spcecific xchi driver and add the configuration options to enable
the generic DWC3 driver on all K2 platforms.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-12-14 17:59:09 +01:00
Jean-Jacques Hiblot
1c03ade328 usb: dwc3-generic: make it compatible with "ti, keystone-dwc3"
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-12-14 17:59:09 +01:00
Adam Ford
f187ace80e usb: musb: Remove legacy CONFIG_USB_DA8XX
There don't appear to be any boards enabling CONFIG_USB_DA8XX,
and there is a newer version of the MUSB driver, so let's remove
the legacy version of it.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-12-14 17:59:09 +01:00
Adam Ford
66c65f0a91 usb: musb: Remove Legacy CONFIG_USB_DAVINCI
This patch removes CONFIG_USB_DAVINCI.  It's a legacy option
that isn't defined anywhere, and there is a newer MUSB driver.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-12-14 17:59:09 +01:00
Martyn Welch
16ecb295b3 usb: Don't enable CONFIG_SPL_DM_USB for non-DM SPL
When CONFIG_SPL_DM_USB was added, it was added defaulted on without
protection to ensure it didn't get set for non-DM SPL builds.

This leads to unexpected and confusing failures when building a DM based
U-Boot but with a non-DM SPL, as the defconfig is unlikely to have
CONFIG_SPL_DM_USB actively disabled.

Tweak the Kconfig to not enable this setting unless CONFIG_SPL_DM is set.

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
2018-12-14 17:59:08 +01:00
Lukasz Majewski
916fa09799 usb: composite: Move bitmap related operations to ./include/linux/bitmap.h
The BITMAP related operations can now be moved to ./include/linux/bitmap.h
file to mimic the Linux kernel directory tree.

This change also allows to remove the lin_gadget_compat.h header file
(which is a legacy code only for composite U-boot layer).
It was also possible to remove #includes from several USB gadget drivers.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
2018-12-14 17:59:08 +01:00
Petr Štetiar
bb00a015d6 usb: gadget: f_sdp: Provide filesize env variable for downloaded images
Currently it's not possible to get filesize of downloaded images and
it's impossible to automate some tasks in scripts. So this patch adds
`filesize` environment variable with size (as hex number in bytes) of
the last successfully downloaded file via `sdp` command.

Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
2018-12-14 17:59:08 +01:00
Jean-Jacques Hiblot
d66e54ac80 dwc3-generic: Add support for the TI DWC3 glue
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-12-07 16:31:46 +01:00
Jean-Jacques Hiblot
4d3825c191 usb: dwc3: Fix a compilation error with the edison defconfig
The error is:
In file included from include/part.h:10:0,
                 from include/usb.h:18,
                 from include/linux/usb/gadget.h:22,
                 from drivers/usb/dwc3/ep0.c:20:
include/ide.h:62:14: error: unknown type name ‘uchar’
 void ide_led(uchar led, uchar status);

Fixing it by including common.h that defines the uchar type.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-12-07 16:31:45 +01:00
Jean-Jacques Hiblot
93991cf196 dwc3-generic: Add select_dr_mode operation
The select_dr_mode operation is executed when the glue driver is probed.
The role of this optional function is to configure the operating mode
of the controller at the glue level.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-12-07 16:31:45 +01:00
Jean-Jacques Hiblot
446e3a205b dwc3-generic: Handle the PHYs, the clocks and the reset lines
This make the driver more generic. At this point this driver can replace
the dwc3-of-simple implementation.
Make the description in the Kconfig more generic too.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-12-07 16:31:45 +01:00
Jean-Jacques Hiblot
0131162439 dm: usb: create a new UCLASS ID for USB gadget devices
UCLASS_USB_DEV_GENERIC was meant for USB devices connected to host
controllers, not gadget devices.
Adding a new UCLASS for gadget devices alone.

Also move the generic DM code for USB gadgets in a separate file for
clarity.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-12-07 16:31:45 +01:00
Jean-Jacques Hiblot
d648a50c0a dwc3: move phy operation to core.c
Those operations can be used for peripheral operation as well as host
operation.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>

# Conflicts:
#	drivers/usb/dwc3/core.c
#	drivers/usb/host/xhci-dwc3.c
2018-12-07 16:31:45 +01:00
Jean-Jacques Hiblot
20bebd8666 dwc3_generic: do not probe the USB device driver when it's bound
The driver will be probed when usb_gadget_initialize() is called.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-12-07 16:31:45 +01:00
Jean-Jacques Hiblot
ff8d755834 usb: udc: implement DM versions of usb_gadget_initialize()/_release()/_handle_interrupt()
When DM_USB_GADGET the platform code for the USB device must be replaced by
calls to a USB device driver.

usb_gadget_initialize() probes the USB device driver.
usb_gadget_release() removes the USB device driver.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2018-12-07 16:31:45 +01:00
Jean-Jacques Hiblot
687ab54560 usb: introduce a separate config option for DM USB device
Using CONFIG_DM_USB for this purpose prevents using DM_USB for host and not
for device.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2018-12-07 16:31:45 +01:00