For now the driver does not probe if usbkbd was not present in stdin.
This presents two issues, we can not probe the driver before setting stdin
and we can not use this driver in other manner than stdin console.
This patch fixes this by adding an else statement. It simply probes the
driver without console management in the case "usbkbd" is not in stdin.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
MPS3 board have a ISP1763 usb controller, enable it to be used
for mass storage access for example. Enable the usb command
also and for the FVP support for mass storage enable the mmc
command.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
ISP1760/61/63 are a family of usb controllers, here the main
goal is to support the ISP1763 hcd part found in the MPS3 FPGA
board form Arm. This is based on the kernel driver and ported
to u-boot.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Move urb code from musb only use to a more common scope, so other
drivers in the future can use the handling of urb in usb.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
When usb PHY initialization is done, the PHY need to be reset.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
keystone doesn't have custom gpio.h that's why don't select
GPIO_EXTRA_HEADER which points to it.
Logic in arch/arm/include/asm/gpio.h is very clear
#ifdef CONFIG_GPIO_EXTRA_HEADER
#include <asm/arch/gpio.h>
#endif
#include <asm-generic/gpio.h>
Where it is visible that there is no gpio.h in platform headers:
$ ls arch/arm/mach-keystone/include/mach/
clock_defs.h clock-k2e.h clock-k2hk.h ddr3.h hardware-k2e.h
hardware-k2hk.h i2c_defs.h mon.h mux-k2g.h xhci-keystone.h
clock.h clock-k2g.h clock-k2l.h hardware.h hardware-k2g.h
hardware-k2l.h mmc_host_def.h msmc.h psc_defs.h
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
PA13 and PA14 are used for USB power control and can't be used
to enforce fastboot or stm32prog mode by pressing a button.
Defining CONFIG_FASTBOOT/CONFIG_CMD_STM32PROG without this patch applied
results in fastboot/stm32prog always starting, because PA13/PA14 are always
low during boot. So drop the wrong trigger gpios definitions.
Signed-off-by: Johann Neuhauser <jneuhauser@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Activate the I2C driver in STM32MP13x config.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Activate the RTC driver in STM32MP13x config.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Activate the RNG driver provided by OP-TEE.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
On STM32MP13x STMicroelectronics boards, the UART can reliably go up to
4000000 bauds when connected to the external ST-LINKV3.
This patch adds the support of higher baudrates on STMicroelectronics
STM32MP13x boards with ST-LINKV3.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Activate the led managed in stm32mp1 board for U-Boot indication
in STM32MP13F-DK device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support of STM32MP13x Rev.Y for the Silicon revision REV_ID = 0x1003.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
New IP adds a conditional reset that impact the clock
error management. It is now linked to a new compatible.
Signed-off-by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The stm32mp13 soc differs from the stm32mp15 in terms of
clear register offset for controlling the FMP (Fast Mode Plus).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a "secure" version of STM32 boards based on SCMI when RCC_TZCR.TZEN=1.
Only boards provided by STMicroelectronics are concerned:
-STM32MP157A-DK1
-STM32MP157C-DK2
-STM32MP157C-ED1
-STM32MP157C-EV1
The resources secured by RCC_TZCR.TZEN=1 are managed by OP-TEE
and the associated SCMI services, reset and clock.
These device trees are only supported with stm32mp15_defconfig,
with OP-TEE, SCMI and without SPL support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
With support of SCMI in OP-TEE, the early malloc usage
increase, the associated defined CONFIG_SYS_MALLOC_F_LEN
need to be increased.
For example, for stm32mp15_defconfig and
stm32mp157c-dk2-scmi.dtsi, we have:
Early malloc usage: 14098 / 80000
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support for new compatible st,stm32mp1-rcc-secure used when the
RCC resource is managed by secured world (RCC_TZCR.TZEN=1)
iand when SCMI is used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the uclass ops of_to_plat to parse the device tree properties
to respect the expected sequence by the driver model.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
All the elements of privdata are static and build from device tree,
they are moved in platdata to prepare the support of ops
of_to_plat.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Rename stm32_sdmmc_bind to stm32_sdmmc2_bind as all other functions
in SDMMCv2 driver
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Change-Id: Ic51acdfbbba6e971809c1029dd2227038bfe879d
Add the node for SCMI firmware with the associated reserved memory nodes
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the node for OP-TEE firmware with the associated reserved memory nodes
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Correctly handle STM32MP_BOARD_EXTRA_ENV define in stm32mp15_st_common.h;
the STM32MP_BOARD_EXTRA_ENV is added in CONFIG_EXTRA_ENV_SETTINGS
definition, as it is done "stm32mp15_st_common.h"
Without this patch, the content of STM32MP_BOARD_EXTRA_ENV is not used in
the default environment for STMicroelectronics boards.
Fixes: 806c4dd315 ("configs: stm32mp1: set the console variable for extlinux.conf")
Reported-by: Gatien CHEVALLIER <gatien.chevallier@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
On p1_p2_rdb_pc platforms, we set ddr_data_init to the "poison" value of
0xdeadbeef rather than a real calculated / derived value. Do this
directly and comment rather than via CONFIG.
Signed-off-by: Tom Rini <trini@konsulko.com>
Perform a basic migration of the calls in setup_serial_number() to DM so
that we can switch to using DM_I2C on this platform.
Cc: David Lechner <david@lechnology.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: David Lechner <david@lechnology.com>
We have a single platform that is both in the OMAP3 family of parts, but
has an EMIF4 memory controller. Currently we hard-code the size of
chip select 0. Make this more clear by putting the value in the
function rather than a CONFIG option.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, the imx8mq_phanbell board fails to boot.
Remove the custom CONFIG_SYS_MALLOC_F_LEN setting in favor of the
generic one done via the main Kconfig.
Since commit b598957206 ("Kconfig: Fix SYS_MALLOC_F_LEN for i.MX8MQ")
the default SYS_MALLOC_F_LEN value for i.MX8MQ is 0x2000.
With such default value, the board boots again.
Signed-off-by: Fabio Estevam <festevam@denx.de>
In case the MALLOC_F_ADDR is set to non-zero value, the early malloc area is
not going to be placed just below stack top, but elsewhere. Do not reserve
MALLOC_F bytes in this case, as that wastes stack space and may even cause
insufficient stack space in SPL.
This functionality is particularly useful on i.MX8M, where the insufficient
stack space can be triggered.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Tom Rini <trini@konsulko.com>
Correct spelling and copy/paste errors in comments.
Fixes 1c4db59d9b ("regmap: Add support for regmap fields")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit d293759d55 ("serial: ns16550: Add support for
SPL_DEBUG_UART_BASE") fixed support for setting correct early debug UART
base address in SPL.
But after this commit, output from Marvell A385 BootROM is truncated or
lost and not fully present on serial console.
Debugging this issue showed that BootROM just put bytes into UART HW output
buffer and does not wait until UART HW transmit all characters. U-Boot
ns16550 early debug is initialized very early and during its initialization
is resetting UART HW and flushing remaining transmit buffer (which still
contains BootROM output).
Fix this issue by waiting in init function prior resetting UART HW until
TxEmpty bit in UART Line Status Register is set. TxEmpty is set when all
remaining bytes from HW buffer are transmitted.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Add comment, move ';' to new line per checkpatch.pl]
Signed-off-by: Tom Rini <trini@konsulko.com>
The top level DT node of pwm-leds is not a LED itself, bind NOP uclass
driver to it, and bind different LED uclass driver to its subnodes which
represent the actual LEDs. This change removes the top-level node from
the 'led list' command output and is based on the commit 0107469780
("led: gpio: Use NOP uclass driver for top-level node").
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
With the current code if the board has an ONFI compliant NAND without
support to the get and set features, U-boot returns an ENOTSUP error when
trying to tune the timings which prevents the probe of the device.
Indeed onfi_set_features() return ENOTSUP error if set/get features is not
supported. In the case of timings we should not return ENOTSUP because we
can use the default timings. The NAND is already capable of listening at
its highest supported rate, so we assume in this case that it is fine to
skip the operation.
Fix it by adding an intermediate nand_onfi_set_timings() function which
does not error out if set/get feature is not supported.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
A new DT binding for describing environment data block has been added in
Linux's commit 5db1c2dbc04c ("dt-bindings: nvmem: add U-Boot environment
variables binding"). Once we get a proper Linux NVMEM driver it'll be
possible to use Linux's binary interface for user-space as documented
in the:
https://www.kernel.org/doc/html/latest/driver-api/nvmem.html
This commits makes fw_env fallback to looking for a compatible NVMEM
device in case config file isn't present. In a long term this may make
config files redundant and avoid code (info) duplication.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
If CONFIG_CC_OPTIMIZE_FOR_DEBUG=y, the host tools should be built with
debug symbols and with reduced optimization.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
sandbox_defconfig builds the DA7219 driver. It should be possible to
build the sandbox without ACPI support.
ACPI support in the DA7219 driver is only needed when creating an ACPI
table. Fix building with ACPIGEN=n.
Fixes: 0324b7123e ("sound: Add an ACPI driver for Dialog Semicondutor da7219")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
sandbox_defconfig builds the max98357a driver. It should be possible to
build the sandbox without ACPI support.
ACPI support in the max98357a driver is only needed when creating an ACPI
table. Fix building with ACPIGEN=n.
Fixes: 54bcca2973 ("sound: Add an ACPI driver for Maxim MAX98357ac")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
