Add i.MX6UL dtsi support from Linux.
Here is the last commit:
"ARM: dts: add gpio-ranges property to iMX GPIO controllers"
(sha1: bb728d662bed0fe91b152550e640cb3f6caa972c)
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.
The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Add proper reg values for the two AIPS bus nodes. This avoids this
two warnings:
Node /soc/aips-bus@40000000 has a unit name, but no reg property
Node /soc/aips-bus@40080000 has a unit name, but no reg property
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
The unit-address should be the same as the I2C address of the device.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Unlike Linux kernel, U-Boot depends on "spi-flash" compatible to probe
m25p80 spi-nor devices. Hence, add "spi-flash" compatible string to
m25p80 node. Without this patch, flash device DT data is not parsed and
QSPI operates in unsupported mode leading to data corruption.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add pin control nodes to APN806, CP-master, CP-slave and
Armada-7040 and Armada-8040 boards DTS files
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Align the Armada-8040-db and Armada-7040-db SPI and I2C
DTS settings with latest DB settings:
- 8040-db: disable i2c0 and spi0 on AP (MPPs are reserved for SDIO)
- 8040-db: disable cps_i2c0 on CP1
- 8040-db: enable spi1 on CP1 (the new location of the boot flash)
The spi1 on CP1 is aliased as spi0 since this is the way
the driver enumerates it.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add CycloneV based Terasic DE1-SoC board. The board boots
from SD/MMC. Ethernet and USB host is supported.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Marek Vasut <marex@denx.de>
Add the name for register space and memory space.
<0x1550000 0x10000 > is the QSPI register space.
<0x40000000 0x4000000> is the QSPI memory space.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add I2C and SPI aliases to enable usage in U-Boot. Otherwise U-Boot will
not be able to use the SPI NOR chip for environment storage and use
"i2c dev 0" to select this I2C bus.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This patch adds the COMPHY device tree configuration to the DT file for
the Marvell DB-88F8040 devel board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This patch adds the COMPHY and UTMI device tree nodes to the cp110-slave
dtsi file for the Armada 8K.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Since the cp110 slave also has comphy DT nodes, the names need to be
renamed to avoid a name clash. Lets use the common naming scheme:
"cpm_xxx" for master and "cps_xxx" for slave.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This patch adds the necessary files to support the Marvell Armada 8k
devel board. Most board specfic files are shared with the Armada 7k
boards under the name "armada-8k*". So only minimal changes are
necessary to add this basic board support (except the DT files of
course).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Add the latest version of the DT files from the Linux kernel.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Add DT support for dra71-evm and built it as part of FIT image.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The information currently set via platdata has to be represented in the
device tree now. bcm283x-uboot.dtsi adds the u-boot specific "skip-init"
property to the serial nodes and enables initialization in the pre-reloc phase.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds device trees for the bcm283x platform to be used with
OF_CONTROL. The version 4.8-rc7 of the linux kernel was used as source.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add board support for sun8i_r16 Nintendo NES Classic edition.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
[jagan: Add commit message body]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This adds support for the Asus Chromebook Flip, an RK3288-based clamshell
device which can flip into 'tablet' mode. The device tree file comes from
Linux v4.8. The SDRAM parameters are for 4GB Samsung LPDDR3.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds support for the Asus Chromebit, and RK3288-based device designed
to plug directly into an HDMI monitor. The device tree file comes from
Linux v4.8.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we have a single rk3288-based Chromebook: chromebook_jerry. But
all such Chromebooks can use the same binary with only device-tree
differences. The family name is 'veyron', so rename the files accordingly.
Also update the device-tree filename since this currently differs from
Linux.
Signed-off-by: Simon Glass <sjg@chromium.org>
Check whether a display device is in use before using it. Add a comment as
to why two displays cannot currently be used at the same time.
This allows us to remove the device-tree change that disables vopb on
jerry.
Signed-off-by: Simon Glass <sjg@chromium.org>
The patch adds support for Freescale ls1021a-iot board.
Signed-off-by: Feng Li <feng.li_2@nxp.com>
[YS: rewrite commit message, fix whitespace in Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
Adding prefetchable memory space to pcie device tree node.
Shifting configuration space to 64-bit address space.
Removing pcie device tree node from amba as it requires size-cells=<2>
in order to access 64-bit address space.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynqmp DMA driver expects two clocks (main clock and apb clock)
For LPDDMA channels the two clocks are missing in the
Dma node resulting probe failure.
xilinx-zynqmp-dma ffa80000.dma: main clock not found.
xilinx-zynqmp-dma ffa80000.dma: Probing channel failed
xilinx-zynqmp-dma: probe of ffa80000.dma failed with error -2
This patch fixes this issue.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
LPDDMA default allows only secured access.
inorder to enable these dma channels,
one should ensure that it allows non secure access.
This patch updates the same.
Reported-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use 64bit size cell for main amba bus instead of 32bit because PCIe
node requires it Change 64bit sizes also for all others IPs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This reverts commit bd750e7a6c
Implemented the new workaround for auto tuning based on
zynqmp compatible string, so removed the 'broken-tuning'
property.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch changes the compatible string for sdhci node,
adds "xlnx,device_id" and "xlnx,mio_bank" property to sdhci node.
Signed-off-by: Sai Krishna Potthuri <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds edac node for arm cortexa53 to report
errors on L1 and L2 caches.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This reverts commit 786db82bd5.
Since we are using serdes driver , no need of mapping serdes register
space into DP driver.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Tested-by: Hyun Kwon <hyunk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Each plane can be associated with multiple DMA channels. So add
index for each DMA channel.
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Updating required device tree changes as per mainlined driver
from 4.6 kernel.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Previously, it was assumed that there is a 1:1 mapping between
PM ID defined in the platform firmware and a PM domain. However, there
can be a situation where multiple PM IDs belong to a single PM domain
(e.g. PM IDs for GPU and two pixel processors correspond to a single
PM domain).
This patch adds support for assigning more than one PM ID to
a single PM domain.
Updated documentation accordingly.
Assigned pixel processors PM IDs to GPU PM domain.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DDR power states are handled by the PM firmware, so this domain is
redundant. Also, since there is no device using this PM domain,
it will be powered off during boot, which is wrong.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add dcc to dtsi for supporting system without serial port.
DCC is enabled by default on ZynqMP.
Adding dcc to zcu100 and zcu102 which were tested.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynqmp DMA driver expects two clocks (main clock and apb clock)
LPDDMA clock cofiguration is missing for the same in the
zynqmp-clk.dtsi file.
This patch updates for the same.
Reported-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DTC 1.4.2 reports these warnings:
Warning (unit_address_vs_reg): Node /amba_apu has a reg or ranges
property, but no unit name
Warning (unit_address_vs_reg): Node /amba has a reg or ranges property,
but no unit name
Warning (unit_address_vs_reg): Node /amba/usb@fe200000 has a unit name,
but no reg property
Warning (unit_address_vs_reg): Node /amba/usb@fe300000 has a unit name,
but no reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-video0channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-video1channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-video2channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-graphicschannel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-audio0channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-audio1channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node /memory has a reg or ranges
property, but no unit name
This patch is fixing them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DTC 1.4.2 reports these warnings:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges
property, but no unit name
Warning (unit_address_vs_reg): Node /pmu has a reg or ranges property,
but no unit name
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name,
but no reg property
This patch is fixing them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The topic-miami SoMs contain a Zynq xc7z015 or xc7z030 SoC, 1GB DDR3L RAM,
32MB QSPI NOR flash and 256MB NAND flash.
The topic-miamiplus SoMs contain a Zynq xc7z035, xc7z045 or xc7z100 SoC,
2x 1GB DDR3L RAM, 64MB dual-parallel QSPI flash, clock sources
and a fan controller.
The "Florida" carrier boards add SD, USB, ethernet and other interfaces.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Update the spi-max-frequency property of m25p80 flash slave to match
that of TI QSPI controller node, so that QSPI operations happen at
maximum supported frequency of 76.8MHz.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Enable the Ethernet device in DT, provide board-specific configuration,
and enable the driver in Kconfig.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tegra186 includes a Synopsys DWC EQoS (Ethernet) device. Add this to the
Tegra186 SoC DT so that boards can make use of it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since we implement the dram capacity auto detect, we don't
need to set the channel number and sdram-channel in dts.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Mostly by adding MACH_SUN50I to some existing #ifdefs enable support
for the the HCI0 USB host controller on the A64.
Fix up some minor 64-bit hiccups on the way.
Add the bare minimum DT bits to the A64 .dtsi and enable the controllers
and the PHY on the Pine64.
This is limited to the first USB controller at the moment, which is
connected to the lower USB socket on the Pine64 board.
[Andre: remove unneeded defines, enable OHCI, add commit message]
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The sun8i-emac driver works fine with the A64 Ethernet IP, but we are
missing an alias entry to trigger the driver instantiation by U-Boot.
Add the line to point U-Boot to the Ethernet DT node.
This enables TFTP boot on the Pine64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fix the warning from dtc like,
---8<----
Warning (unit_address_vs_reg): Node /ahb/apb/pmc@f0014000/periph64ck/sdmmc0_hclk has a reg or ranges property, but no unit name
--->8----
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
i.CoreM6 Quad/Dual modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU NXP i.MX6 DQ, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add imx6q pinctrl defines support from Linux.
Here is the last commit:
"ARM: dts: imx: pinfunc: add MX6QDL_PAD_GPIO_6__ENET_IRQ"
(sha1: d8c765e0d1ddbd5032c2491c82cc9660c2f0e7f2)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add i.MX6Q dtsi support from Linux.
Here is the last commit:
"ARM: dts: add gpio-ranges property to iMX GPIO controllers"
(sha1: bb728d662bed0fe91b152550e640cb3f6caa972c)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
i.CoreM6 DualLite/Solo modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU NXP i.MX6 DL, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add imx6dl pinctrl defines support from Linux.
Here is the last commit:
"ARM: dts: imx: pinfunc: add MX6QDL_PAD_GPIO_6__ENET_IRQ"
(sha1: d8c765e0d1ddbd5032c2491c82cc9660c2f0e7f2)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add i.MX6DQL dtsi support from Linux.
Here is the last commit:
"ARM: dts: imx6qdl: Fix SPDIF regression"
(sha1: f065e9e4addd75c21bb976bb2558648bf4f61de6)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add i.MX6DL dtsi support from Linux.
Here is the last commit:
"ARM: dts: add gpio-ranges property to iMX GPIO controllers"
(sha1: bb728d662bed0fe91b152550e640cb3f6caa972c)
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Without this patch the following error will be shown:
Colibri T20 # usb start
starting USB...
No controllers found
This patch fixes USB operation and also the controller order as the
CI UDC driver may only be instantiated on the first aka OTG port.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Without this patch the following error will be shown:
stdio_add_devices: Video device failed (ret=-22)
As commit ec5507707a (video: tegra: Move
to using simple-panel and pwm-backlight) states the Colibri T20 needs
updating too which this patch finally attempts doing.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add DTS support for dra72 evm Rev C which has the following
changes
* Two ethernet ports now instead of the single one in rev B.
* DP83867 ethernet phy instead of DP838865.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add the USB node for LS2080a in dts.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
[York Sun: replace ls2080 with ls2080a in commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Add device tree node for Ricoh RN5T567. Currently we do not need
the individual DC/DC converters or LDO's (and they are also not
yet supported by the driver).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Add base device for NXP i.MX 7Solo/7Dual. The two SoC are very
similar and hence can share the same device tree for boot loaders
purpose.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add pinctrl defines for NXP i.MX 7Solo/7Dual SoC. The pinctrl format
is compatible to the Linux kernel, hence this file is a simple copy
from the Linux kernel (commit 97f5c1817b7e).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
