This commit replaces hard-coded EMIF and PHY DDR3 configurations for
predefined SODIMMs to a calculated configuration. The SODIMM parameters
are read from SODIMM's SPD and used to calculated the configuration.
The current commit supports calculation for DDR3 with 1600MHz and 1333MHz
only.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is based on the davinci da850evm. It can boot from either the
on-board 16MB flash or from a microSD card. It also reads board
information from an I2C EEPROM.
The EV3 itself initally boots from write-protected EEPROM, so no
u-boot SPL is needed.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable support for PMMC the TI power processor on K2G. This processor
manages all power management related activities on the SoC and and
allows the Operating Systems on compute processors such as ARM, DSP to
offload the power logic away into the power processor.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Current AM57xx evm supports both BeagleBoard-X15
(http://beagleboard.org/x15) and AM57xx EVM
(http://www.ti.com/tool/tmdxevm5728).
The AM572x EValuation Module(EVM) provides an affordable platform to
quickly start evaluation of Sitara. ARM Cortex-A15 AM57x Processors
(AM5728, AM5726, AM5718, AM5716) and accelerate development for HMI,
machine vision, networking, medical imaging and many other industrial
applications. This EVM is based on the same BeagleBoard-X15 Chassis
and adds mPCIe, mSATA, LCD, touchscreen, Camera, push button and TI's
wlink8 offering.
Since the EEPROM contents are compatible between the BeagleBoard-X15 and
the AM57xx-evm, we add support for the detection logic to enable
support for various user programmable scripting capability.
NOTE: U-boot configuration is currently a superset of AM57xx evm and
BeagleBoard-X15 and no additional configuration tweaking is needed.
This change also sets up the stage for future support of TI AM57xx EVMs
to the same base bootloader build.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable CONFIG_USB_ETHER_RTL8152 support for Odroid XU4 which
has support for RTL8153-CG gigabit Ethernet adapter,
connected over USB 3.0.
commit 9dc8ba19c5 added support
for Realtek 8152/8153 driver.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Select 8-bit BCH ecc-scheme with s/w based error correction
- OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move to booting a zImage kernel by default to align with the other
i.MX boards.
While at it, adjust the fdt_addr so that we can boot a standard
mainline kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
"fastboot oem format" command reuses "gpt write" command, which in turn
requires correct partitions defined in $partitions variable. This patch
adds such definition of Android partitions for DRA7XX EVM board.
By default $partitions variable contains Linux partition table. In order
to prepare Android environment one can run next commands from U-Boot
shell:
=> env set partitions $partitions_android
=> env save
After those operations one can go to fastboot mode and perform
"fastboot oem format" to create Android partition table.
While at it, enable CONFIG_RANDOM_UUID to spare user from providing
UUIDs for each partition manually.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces some minor cleanups, regarding aspects such as board name, code
and headers organization as well as deprecated and missing config options.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are a number of AMCC platforms which are close to, or with some
toolchains exceeding, the size constraints. Disable CONFIG_SYS_LONGHELP
to get us room to build with again.
Signed-off-by: Tom Rini <trini@konsulko.com>
Of the several boot devices supported, it looks like the eMMC is the
most commonly used. Enable CONFIG_ENV_IS_IN_MMC by default.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Boot ROM expects the boot image (SPL) in the Boot Partition 1.
So, updating images involves the hardware partition switch. It might
be a bit advanced for some users.
To be user-friendly, this commit adds a useful command to update the
images; just put SPL and U-Boot proper into the public directory of
the TFTP server and execute "run emmcupdate" from the command line.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Export device nodes needed for eMMC boot (eMMC node, pinctrl, and
clock) to the SPL DTB. CONFIG_SUPPORT_EMMC_BOOT is also necessary
to use "mmc partconf" command.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable the driver in all UniPhier defconfig files and add some
needed defines to the common files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The patch that enabled eSDHC peripheral clock support had an
obvious error as below. This patch is used to fix it.
+#define define CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK
Fixes: 3285e6cbcc ("powerpc/t2080qds: enable eSDHC peripheral clock support")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This allows all the hush tests implemented in test/py to pass, under qemu
at least.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Scrolling the simple framebuffer is really slow in Raspberry Pi to the
point it delays the boot by a second or two and makes longer output
inconvenient to follow (printenv, md).
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Commit 755324 (configs: Use config_distro_defaults.h in ti_armv7_common.h)
made ti_armv7_common.h include config_distro_defaults.h. This breaks the
bootdelay feature in cm_t43 because now the
- #include ti_armv7_common.h (#define CONFIG_BOOTDELAY 1)
- #undef CONFIG_BOOTDELAY
- #include config_distro_defaults.h (#define CONFIG_BOOTDELAY 2)
dance in cm_t43.h is no longer valid and in fact leads to CONFIG_BOOTDELAY
not being defined.
Adapt the config file to the new inclusion hierarchy.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update U-Boot offset and size for raw mmc boot.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
During boot, U-Boot raises the CPU frequency but the CORE and MPU regulators
are not updated. This is not a problem in cold boot since the default values
that the pmic outputs are correct, but if Linux were to switch the module to a
low power OPP, the new voltage values will be retained after a reboot and the
module will likely hang once U-Boot raises the CPU frequency back up.
Set both CORE and MPU regulators to to 1.1V on boot.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add full support for SPI flash chips to future-proof U-Boot for cm-t43.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move CONFIG_DM_SERIAL to cm_t43_defconfig. This forces us to update the
CONFIG_SYS_NS16550_REG_SIZE value for SPL.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
spl_board_init() is necessary for boot. Remove the #undef that keeps
it out of the boot sequence.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
bur_am335x_common.h today holds all common configuration which is shared
over all B&R boards.
In future we want to bring up boards which are not based on AM335x only
but we still want to have common configuration over all B&R boards
independent from their architecture.
To prepare this we introduce a new file "bur_cfg_common.h", where we
move all common things, which are not architecture specific, from
bur_am335x_common.h.
On B&R am335x boards we include from now:
#include <configs/bur_cfg_common.h>
#include <configs/bur_am335x_common.h>
On other B&R boards, we include only
#include <configs/bur_cfg_common.h>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
We drop everything possible things from board headerfiles and replace
this functionality with responsible settings in Kconfig (_defconfig).
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
During very early prototype-phase we did boot the AM335x boards
initially from CPSW-EMAC.
Now we don't need this feature anymore.
So we drop it to save MLO-space and having therefore a more quickly
boot.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
Logic PD makes four different system on modules. This patch will auto
detect the board type and identify the corresponding device tree image.
V2:
Added 'default:' case to switch statement
Since board_late_init() is defined as int, we now return 0
Signed-off-by: Derald Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Add the missing CONFIG_BUILD_TARGET to get u-boot-with-spl.sfp built
automatically upon running make in the source tree.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Denis Bakhvalov <denis.bakhvalov@nokia.com>
Don't understand how it happened, but this change got applied twice!
Therefore, removing the duplicated items.
Signed-off-by: Steve Rae <srae@broadcom.com>
As tested on the Odroid XU3, large files to be stored on the file system
require considerable time to be physically written to the medium.
The default 300 ms is not enough to store large file (e.g. 26 MiB).
To fix this situation the DFU_MANIFEST_POLL_TIMEOUT has been defined.
It is used to cease the communication with dfu-util and allow the target
board to store the data on file system.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Before Linux boot DPL must be deployed to DPAA2 interface.
So update bootcmd env variable to make sure DPL deployment before
Linux boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Define mcinitcmd env variable to load Management complex during
u-boot boot sequence.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported
in SD boot now. For the customer's demand, QSPI needs to be supported
in SD boot too.
This patch adds QSPI or IFC support in SD boot according to the
corresponding defconfig. For detail, ls1021aqds_sdcard_ifc_defconfig
is used to support IFC in SD boot and ls1021aqds_sdcard_qspi_defconfig
is used to support QSPI in SD boot.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for phy 1-3.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: use setclrbits_le32 instead of read-modify-write]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
SY8106A is a PMIC which is used on the Allwinner
H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is
implemented to set the default V-CPU voltage to 1200 mV.
This driver is required to ensure the SY8106A V-CPU
voltage is set to 1200 mV after a software reset. On cold
boot the default SY8106A output voltage is selected to be
1200 mV by a pair of resistors on the Orange Pi PC and Plus.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Split duart configuration as device tree file. Move /chosen node
out of board commone device tree. Convert ls1021aqds nor and SD
configurations to driver model support (qspi already uses DM).
Enable ns16550 DM serial driver for nor configurations.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
CC: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
