Commit graph

148 commits

Author SHA1 Message Date
Albert ARIBAUD
79f3877794 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'
This required manual merging drivers/mtd/nand/Makefile
and adding am335x_evm support for CONFIG_SPL_NAND_DRIVERS
2013-01-08 13:15:45 +01:00
Yegor Yefremov
cfd4ff6f0f am335x: disable internal delay for RGMII mode
According to errata the AM335x device does not support internal delay
mode, so RGMII1_IDMODE and RGMII2_IDMODE must be set to 1.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2012-12-10 08:56:38 -07:00
Peter Barada
8c4445d266 Pass sdrc timing values through board_sdrc_timings structure
Instead of passing individual registers by value to board_get_mem_timings,
pass a board_mem_timings structure pointer for the board files to fill in.
Pass same structure pointer to write_sdrc_timings.  This saves about
90 bytes of space in SPL.

Signed-off-by: Peter Barada <peter.barada@logicpd.com>
2012-12-10 08:54:02 -07:00
Ilya Yanok
98b5c26943 am335x_evm: enable NAND support
Enable NAND support for AM335X boards.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10 08:54:02 -07:00
Ilya Yanok
70fb65b093 am335x_evm: add nand pinmux definition
Add NAND pins mux settings for AM335X devices. Enable NAND pins
for AM335X EVM board.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10 08:54:01 -07:00
Ilya Yanok
c642b151f3 omap3_beagle: add musb-new init
Add initialization for new MUSB framework.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-20 00:16:08 +01:00
Ilya Yanok
d2aa1154b9 am335x_evm: enable both musb gadget and host
Enable musb gadget in Ethernet mode on port 0 and
musb host on port1.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-20 00:16:07 +01:00
Tom Rini
6acc7c3cbc Merge branch 'master' of git://git.denx.de/u-boot-arm 2012-11-05 07:42:00 -07:00
Albert ARIBAUD
a42c87f9d8 Merge remote-tracking branch 'u-boot-ti/master' 2012-11-03 10:05:22 +01:00
Tom Rini
044fc14bcb am335x_evm: Add CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG support
We add CONFIG_ENV_VARS_UBOOT_CONFIG,
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and CONFIG_BOARD_LATE_INIT to set
the variables and then fdtfile and findfdt to make us of this.  It is
now possible to do 'run findfdt' to have fdtfile be set to the value of
the dtb file to load for the board we are running on.

Signed-off-by: Tom Rini <trini@ti.com>
2012-11-02 15:14:28 -07:00
Matthias Fuchs
a956bdcb3f am335x: add initial AM335x IDK board support
This patch extends the am335x_evm board for the AM335x IDK.

The IDK board uses MII for the ethernet phy (same as
Beaglebone board) and MMC0 for storage (but without
card detect line).

The IDK uses UART3 for console. So u-boot must be build
with CONFIG_SERIAL4 and CONFIG_CONS_INDEX=4 or for
the am335x_evm_uart3 board configuration as introduced
by Andrew Bradfords recent patch series "am33xx: Enable
UART {1,2,3,4,5}...". When using the IDK with console on UART0,
those patches are not required. In this case the board
slightly needs to be modified.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2012-11-02 10:04:04 -07:00
Koen Kooi
9cd7b4cdca am335x: add mux config for DDR3 version of beaglebone
This fixes the following boothang in SPL:

	Unknown board, cannot configure pinmux.### ERROR ### Please RESET the board ###

Future commits will add pinmuxes for more on-board peripherals.

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
2012-10-30 15:28:44 -07:00
Albert ARIBAUD
c68436fa42 Merge remote-tracking branch 'u-boot-ti/master' 2012-10-26 07:00:28 +02:00
Andrew Bradford
6422b70bd5 am33xx: Enable UART{1,2,3,4,5} pin-mux
If configured to use UART{1,2,3,4,5} such as on the Beaglebone RS232
cape or on the am335x_evm daughterboard, enable the proper pin-muxing.

Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
2012-10-25 14:54:50 -07:00
Peter Korsgaard
c7d35bef25 am33xx/ddr_defs.h: rename DDR2/DDR3 defines to their actual part numbers
So other parts can be added.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25 11:31:38 -07:00
Peter Korsgaard
c00f69dbcd am33xx: support board specific ddr settings
Move the hardcoded ddr2/ddr3 settings for the ti boards to board code,
so other boards can use different types/timings.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make apply with rtc32k_enable() in the file]
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25 11:31:38 -07:00
Peter Korsgaard
7f26a5a26f am33xx: move generic parts of pinmux handling out from board/ti/am335x
So they are available for other boards.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25 11:31:37 -07:00
Peter Korsgaard
e363426e99 am33xx: move ti i2c baseboard header handling to board/ti/am335x/
The i2c header is specific to ti(-derived) boards, and not generic for all
am335x boards.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make re-apply with rtc32k_enable() applied]
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25 11:31:36 -07:00
Ashok
860bde3fee omap2424:Rename CONFIG_DRIVER_LAN91C96 to CONFIG_LAN91C96 as CONFIG_DRIVER_LAN91C96 is obsolete.
Rename CONFIG_DRIVER_LAN91C96 to CONFIG_LAN91C9 as
CONFIG_DRIVER_LAN91C96 is obsolete.

Signed-off-by: Ashok Kumar Reddy <ashokkourla2000@gmail.com>
2012-10-22 08:31:57 -07:00
Lucas Stach
676ae068d9 usb: ehci: rework to take advantage of new lowlevel interface
Kill off ehci-core.h
It was used to specify some static controller data. To support more than
one controller being active at any time we have to carry the controller
data ourselfes. Change the ehci interface accordingly.

NOTE: OMAP implemented the ehci stuff a bit backwards and should be fixed
to do the same thing as other platforms. But the change for now is at least
compile clean.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
2012-10-15 11:54:00 -07:00
Albert ARIBAUD
b823fd9ba5 ARM: prevent misaligned array inits
Under option -munaligned-access, gcc can perform local char
or 16-bit array initializations using misaligned native
accesses which will throw a data abort exception. Fix files
where these array initializations were unneeded, and for
files known to contain such initializations, enforce gcc
option -mno-unaligned-access.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Switch to usign call cc-option for -mno-unaligned-access as
Albert had done previously as that's really correct]
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-15 11:53:07 -07:00
Ilya Yanok
7ac2fe2da2 OMAP: networking support for SPL
This patch adds support for networking in SPL. Some devices are
capable of loading SPL via network so it makes sense to load the
main U-Boot binary via network too. This patch tries to use
existing network code as much as possible. Unfortunately, it depends
on environment which in turn depends on other code so SPL size
is increased significantly. No effort was done to decouple network
code and environment so far.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-01 10:02:14 -07:00
Tom Rini
a4a99fffd8 am335x evm: Enable support for spi0
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:19 +02:00
Tom Rini
6bfca5031b am335x evm: Enable MMC1 pinmux
MMC1 is available in profile 2 on the GP EVM and is exposed on the
expansion header on beaglebone.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:18 +02:00
Tom Rini
036fd65a8c am335x evm: Initial support for AM335x GP EVM Profiles
The AM335x GP EVM can have one of 8 different profiles selected.  Each
profile has a different set of peripherals and requires different pinmux
configurations that conflict with other profiles.  i2c1 is an example of
a conflicted mux currently.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:18 +02:00
Tom Rini
db7dd8109c am33xx: Rework pinmux functions
- Move definition of the EEPROM contents to <asm/arch/sys_proto.h>
  - Make some defines a little less generic now.
- Pinmux must be done by done by SPL now.
- Create 3 pinmux functions, uart0, i2c0 and board.
- Add pinmux specific to Starter Kit EVM for MMC now.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
65d750be59 am33xx: Add support for TI AM335x StarterKit EVM
- Board requires gpio0 #7 to be set to power DDR3.
- Board uses DDR3, add a way to determine which DDR type to call
  config_ddr with.
- Both of the above require filling in the header structure early, move
  it into the data section.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini
973b663820 am33xx: Remove board/ti/am335x/evm.c
The intention has always been (and boards are to support) an i2c EEPROM
that will identify what hardware they are, allowing a single binary to
support multiple boards.  As such, remove the 'evm.c' file as there is
nothing EVM centric in it currently, only SoC peripheral configuration.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Chandan Nath
9304296044 am335x_evm: CPSW support
This patch adds board-specific initialization for CPSW on
TI AM335X based boards. Tested on BeagleBone.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split board-specific part into separate patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01 14:58:11 +02:00
Ilya Yanok
c59a6a0dac am335x_evm: read the on-board EEPROM
Read the on-board EEPROM during startup to detect the version
of the board we are running on (as for now only BeagleBone vs
EVM detection is supported).

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01 14:58:11 +02:00
Chandan Nath
89017e150e am33xx: pin mux defintions for CPSW switch
This patch adds pin mux settings for CPSW switch found on
TI AM335X based boards (MII and RGMII modes).

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split pinmux into separate patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01 14:58:11 +02:00
Peter Meerwald
2c30c18487 beagle: only call DSS code when #defined CONFIG_VIDEO_OMAP3
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-09-01 14:58:10 +02:00
Steve Sakoman
d3decdebde omap: am335x_evm: enable i2c1 channel
This patch sets up pinmux, enables fclk, and
defines CONFIG_I2C_MULTI_BUS

Signed-off-by: Steve Sakoman <steve@sakoman.com>
2012-09-01 14:58:10 +02:00
Peter Meerwald
71a271c654 beagle: removed unused pr_debug #define
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
2012-09-01 14:58:10 +02:00
Peter Meerwald
fff1a57208 beagle: make get_expansion_id(), get_board_revision(), beagle_display_init() static
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-09-01 14:58:10 +02:00
Steve Sakoman
28adc91a28 omap: am335x_evm: remove unused definitions
UART_RESET, UART_CLK_RUNNING_MASK, and UART_SMART_IDLE_EN
are defined inn evm.c but not used. Also removes unnecessary
include of serial.h

PHYS_DRAM_1_SIZE is defined in am335x_evm.h but never used.

Signed-off-by: Steve Sakoman <steve@sakoman.com>
2012-09-01 14:58:09 +02:00
Wolfgang Denk
b98b611502 Merge branch 'next' of git://git.denx.de/u-boot
* 'next' of git://git.denx.de/u-boot:
  MPC8xx: Fixup warning in arch/powerpc/cpu/mpc8xx/cpu.c
  doc: cleanup - move board READMEs into respective board directories
  net: sh_eth: add support for SH7757's GETHER
  net: sh_eth: modify the definitions of regsiter
  net: sh_eth: add SH_ETH_TYPE_ condition
  net: sh_eth: clean up for the SH7757's code
  net: fec_mxc: Fix MDC for xMII
  net: fec_mxc: Fix setting of RCR for xMII
  net: nfs: make NFS_TIMEOUT configurable
  net: Inline the new eth_setenv_enetaddr_by_index function
  net: allow setting env enetaddr from net device setting
  net/designware: Consecutive writes to the same register to be avoided
  CACHE: net: asix: Fix asix driver to work with data cache on
  net: phy: micrel: make ksz9021 phy accessible
  net: abort network initialization if the PHY driver fails
  phylib: phy_startup() should return an error code on failure
  net: tftp: fix type of block arg to store_block

Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-07-30 20:39:52 +02:00
Wolfgang Denk
702e6014f1 doc: cleanup - move board READMEs into respective board directories
Also drop a few files referring to no longer / not yet supported
boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2012-07-29 15:42:02 +02:00
SRICHARAN R
d2ebaa41ed ARM: OMAP4: PANDA: Add rest of the USB module pads to essentials
In commit 1a89a217f5 we moved most of the
required pads and mux data for USB to the essential list so that later
on we could NOT enable anything that wasn't essential unless otherwise
configured.  This was however missing a few pandaboard-specific parts
which left for example USB ethernet non-functional.

Tested this on OMAP4430 ES2.2, OMAP4460 ES1.1 PANDA boards.

(Reworded by Tom Rini to be more precise about what the problem was)

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Tested-by: Tom Rini <trini@ti.com>
2012-07-20 14:24:08 +02:00
Peter Meerwald
ef88e60902 beagle: add eeprom expansion board info for bct brettl4
this is for a prototyping board

vendor/product ids have been added to
http://elinux.org/BeagleBoardPinMux#List_of_Vendor_and_Device_IDs

Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-07-09 22:44:32 +02:00
SRICHARAN R
1a89a217f5 ARM: OMAP4/5: Move USB pads to essential list.
USB module pads are getting enabled under non-essential
group. These will be required for fastboot, tftp support.
So move this to essential list to have them working when
non-essential pads are no more muxed.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-07-07 14:07:36 +02:00
Tom Rini
2ab2810375 am33xx: Do not call init_timer twice
We do not need to call init_timer both in SPL and U-Boot itself, just
SPL needs to initialize the timer.

Signed-off-by: Tom Rini <trini@ti.com>
2012-07-07 14:07:21 +02:00
Tero Kristo
954211cb8c omap4: panda: disable uart2 pads during boot
If uart2 is enabled during boot, spurious wifi chip transmission will
hang the module and it is impossible to recover from this situation
without hard reset. This will prevent any l4_per domain idle
transitions.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
2012-05-15 08:31:40 +02:00
Tom Rini
60bd10df8a omap730p2: Remove empty misc_init_r
We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R

Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15 08:31:27 +02:00
Tom Rini
b8f4a728e6 omap5912osk: Remove empty misc_init_r
We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R

Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15 08:31:27 +02:00
SRICHARAN R
2114429896 power: twl6035: add palmas PMIC support
palmas/TWL6035 is power IC for omap5 evm boards

Signed-off-by: Balaji T K <balajitk@ti.com>
2012-05-15 08:31:25 +02:00
SRICHARAN R
84b16af29f OMAP5: board: Add pinmux data for omap5_evm board.
Adding the full pinmux data for OMAP5430 sevm board.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15 08:31:23 +02:00
Nishanth Menon
3acb553439 OMAP4460: TPS Ensure SET1 is selected after voltage configuration
TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms.
Currently we control this pin with a mux configuration as part of
boot sequence.
Current configuration results in the following voltage waveform:
                           |---------------| (SET1 default 1.4V)
                           |               --------(programmed voltage)
                           | <- (This switch happens on mux7,pullup)
vdd_mpu(TPS)         -----/ (OPP boot voltage)
                                             --------- (programmed voltage)
vdd_core(TWL6030)    -----------------------/ (OPP boot voltage)
Problem 1)                |<----- Tx ------>|
   timing violation for a duration Tx close to few milliseconds.
Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP.

By using GPIO as recommended as standard procedure by TI, the sequence
changes to:
                                  -------- (programmed voltage)
vdd_mpu(TPS)         ------------/ (Opp boot voltage)
                                   --------- (programmed voltage)
vdd_core(TWL6030)    -------------/ (OPP boot voltage)

NOTE: This does not attempt to address OMAP5 - Aneesh please confirm

Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2012-05-15 08:31:22 +02:00
Jonathan Solnit
bbbc1ae921 ARM:OMAP+:MMC: Add parameters to MMC init
Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency.  While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board.  The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.

Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
2012-05-15 08:31:22 +02:00
Joel Fernandes
aae58b954b BeagleBoard: Remove userbutton command and use gpio command instead
Remove userbutton command and do the detection in board config file using the gpio command

Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2012-04-16 14:47:58 +02:00