add support to read mac address for AM18x EVM manufactured from
Spectrum digital which have mac address stored in I2C EEPROM manufactured
by WINBOND. This patch reads mac address from I2C EEPROM and sets the
environment variable if not set, If mac address is already present in
environment compare it with the mac address in EEPROM and warn on
mismatch.Introduced a config option CONFIG_MAC_ADDR_IN_EEPROM to where
to look for the mac address.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Wolfgang Denk <wd@denx.de>
add support to read mac address for da850/L138 evm manufactured by
Logic PD which store mac address in SPI flash manufactured by ST
Microelectronics. This patch adds support to read mac address from
SPI flash and set the mac address if it hasn't been set in environment,
If it has been set in the environment it compares the value one with
SPI flash and warns on mismatch. Introduced a config option
CONFIG_MAC_ADDR_IN_SPIFLASH indicating where to look mac address for.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Wolfgang Denk <wd@denx.de>
This patch moves hawkboard to the new spl infrastructure from the
older nand_spl one.
Removed the hawkboard_nand_config build option -- The spl code now
gets compiled with hawkboard_config, after building the main u-boot
image, using the CONFIG_SPL_TEXT_BASE. Modified the README.hawkboard
to reflect the same.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
there are two boards based on da850 SOC - OMAP-L138 and AM18x.
In order to differentiate between these two boards, revision id
is passed to kernel via second byte of ATAG_REVISION.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
The boards in board/davinci/da8xxevm/ define pinmux_config[] vectors
that contain pinmux configurations for emac, uarts, memory controllers...
In an earlier patch such pinmux configurations were added to the arch
tree. This patch makes the hawkboard use these definitions instead of
defining its own.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Syed Mohammed Khasim <sm.khasim@gmail.com>
Cc: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Heiko Schocher <hs@denx.de>
The boards in board/davinci/da8xxevm/ define pinmux_config[] vectors
that contain pinmux configurations for emac, uarts, memory controllers...
In an earlier patch such pinmux configurations were added to the arch
tree. This patch makes the da850evm use these definitions instead of
defining its own.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Heiko Schocher <hs@denx.de>
Pinmux configuration for the EMAC was done in a separate call
of davinci_configure_pin_mux(). This patch moves all the pinmux
configuration that is done for this board to a common place.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
The configuration in struct pinmux_config i2c_pins does not configure
the pins for i2c but for uart. Since this function is already
configured by struct pinmux_config uart2_pins the i2c_pins struct
is obsolete.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Heiko Schocher <hs@denx.de>
Cc: Syed Mohammed Khasim <sm.khasim@gmail.com>
Cc: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
This patch replaces the HAWKBOARD_KICK{0,1}_UNLOCK defines by
DV_SYSCFG_KICK{0,1}_UNLOCK.
The kick register values are not hawkboard specific but may be used
for all davinci boards. In commit f3c149d6c6
new defines for these values wer introduced.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Syed Mohammed Khasim <sm.khasim@gmail.com>
Cc: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Since commit f1d2b313c9 the serial
port of the da850evm is accessed before the UART2 peripheral of
the SoC is powered on in the function board_init() in
board/davinci/da8xxevm/da850evm.c.
When u-boot is used in conjunction with the UBL (user boot loader, see
doc/README.davinci) on this board, the UART2 peripheral is already
turned on by UBL at the time u-boot is started. Hence, the wrong
initialization sequence is not noticed by most users. However, if UBL is not
used, u-boot must power on the peripheral before using it.
This patch adds a board_early_init_f() function for the LPSC
configuration to the da850evm board configuration.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add support for enabling NAND boot mode in configuration file and
add correspanding pinmux support, nand initialize function in board file.
The size required for environment variables not more than 10KB
the CONFIG_ENV_SIZE is set to 10KB from (512 << 10).
Acked-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Fix build problem:
nand_spl/board/davinci/da8xxevm/hawkboard_nand_spl.c: In function 'board_init_f':
nand_spl/board/davinci/da8xxevm/hawkboard_nand_spl.c:132: warning: implicit declaration of function 'nand_boot'
nand_spl/board/davinci/da8xxevm/hawkboard_nand_spl.c:133: warning: 'noreturn' function does return
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Syed Mohammed Khasim <sm.khasim@gmail.com>
Cc: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
AHCLKR/UART1_RTS/GP0[11] pin needs to be configured for
NOR to work on Rev.3 EVM. When GP0[11] is low,
the SD0 interface will not work, but NOR flash will.
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
add support for DSP wake-up by default on DA850/OMAP-L138
during board initialization. Enable hwconfig environment and added
extra env setting through CONFIG_EXTRA_ENV_SETTINGS.
To prevent DSP from being woken up,set the environment variable as,
set hwconfig "dsp:wake=no"
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add pin-mux support for NOR in board file and correspanding
macros to use NOR boot mode in configuration file.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The current NAND timings, introduced in commit
a3f88293dd da850evm: setup the NAND flash
timings , incorrectly set WSTROBE and TA to 0. A more recent inspection of the
values set by the Linux kernel indicates that these should be set to 1.
Set the WSTROBE and TA field of the EMIFA cycle-count timings configuration to
1 to match the values set by linux.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Stefano Babic <sbabic@denx.de>
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
As more Davinci 8xx board can be added, move common code
to be shared between boards.
* rebased ontop of Sugosh's patches
* moving the HAWKBOARD_KICK{0,1}_UNLOCK defines to
arch/arm/include/asm/arch-davinci/davinci_misc.h from to
arch/arm/include/asm/arch-davinci/da8xx_common.h
* don't define dram functions in PRELOADER
* move sync_env_enetaddr into existing EMAC ifdef
* use misc.c in hawkboard nand_spl
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch is a port of the work by Sudhakar Rajeshekhara in commit
ab3effbcad8851cc65dc5241a01c064d2030a3b2 of
git://arago-project.org/git/people/sandeep/u-boot-davinci.git.
The da850 UI board has on it an RMII PHY which can be used if the MDC line
to the MII PHY on the baseboard is disabled and the RMII PHY is enabled by
configuring the values of some GPIO pins on the IO expander of the UI board.
This patch implements disabling that line via GPIO2[6], configuring the UI
board's IO expander and setting only the pinmux settings that are needed for
RMII operation.
Tested on da850evm by adding a define for CONFIG_DRIVER_TI_EMAC_USE_RMII.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The patch adds basic board support for TI's OMAP-L138 based
Hawkboard. This board is pretty similar to the da850 EVM. Support for
nand and network access is added in this version.
The following bootup procedure is used.
At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand
controllers and copies the second stage bootloader(nand_spl) to
RAM. The secondary bootloader then copies u-boot from a predefined
location in the nand flash to the RAM, and passes control to the
u-boot image.
Three config options are supported
* hawkboard_config - Used to create the u-boot.bin. Tftp the
u-boot.bin image to the RAM from u-boot, and flash to the nand flash
at address 0xe0000.
* hawkboard_nand_config - Used to generate the secondary
bootloader(nand_spl) image. This creates an elf file u-boot-spl
under nand_spl/. Create an AIS signed image using this file, and
flash it to the nand flash at address 0x20000. The ais file should
fit in one block.
* hawkboard_uart_config - This is same as the first image, but with
the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
board/davinci.
Move the davinci common headers to the architecture specific
include file path.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The TI DA850/OMAP-L138/AM18x EVM can be populated with devices
having different maximum allowed CPU clock rating.
The maximum clock the chip can support can only be determined from
the label on the package (not software readable).
Introduce a method to pass the maximum allowed clock rate information
to kernel using ATAG_REVISION. The kernel uses this information to
determine the maximum cpu clock rate reachable using cpufreq.
Note that U-Boot itself does not set the CPU clock rate. The CPU
clock is setup by a primary bootloader ("UBL"). The rate setup by
UBL could be different from the maximum clock rate supported by the
device.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
now unnecessary config.mk file.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.
Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The current da850evm support in u-boot/master omits any use of
the davinci EMAC. This patch adds basic support for the EMAC using
the MII PHY found on the baseboard of the EVM. The MAC address is
read from the environment variable 'ethadd'. Note that this is
different from the da850evm support in the u-boot omapl1 tree
where the MAC address is read from SPI flash.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The default NAND flash timings are very conservative. This patch assigns the
timings reccomended in the recent linux kernel patch [1] from Sekhar Nori. The
speedup, as reported in that patch, is 5.3x for reads.
[1] http://www.spinics.net/lists/arm-kernel/msg100278.html
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
There is currently no NAND pinmux enabled by the da850evm board setup code.
This is fine when booting from NAND since the early boot code (UBL) will setup
the pinmux; however, when the boot mode is any other setting NAND is unusable
when enabled in the config.
This patch adds a pinmux list for NAND and enables it when NAND is enabled in
the config. Tested by booting from SPI on the da850evm and verifying NAND
was usable.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch proposes to migrate the davinci_emac driver to using the
eth_device->write_hwaddr function pointer as suggested by Ben Warren.
All the davinci boards had the behaviour, prior to this patch, of
sync'ing the environment variable enetaddr with the MAC address read
from non-volatile storage on boot -- when the two locations disagreed,
the environment variable value took precendence. This patch keeps the
same behaviour but lets eth_initialize take care of it.
This patch refactors davinci_emac setup in the boards so that the MAC
address is read from non-volatile storage into the environment variable
and then the environment variable value is use in eth_intialize. The
only exception is the direct call to davinci_eth_set_mac_addr made by
the da830evm board init which was changed into an assignment of the
enetaddr field.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Tested-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Usage of parenthesis in pinmux macro definition changes the
definition of the macro and raises the precedence of '&'
operator inadvertently over '[]'.
Signed-off-by: Prakash PM <prakash.pm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Existing code returns checkpatch error on pinmux macro definition for
not enclosing the definition in parenthesis. The error can be observed in
the patch generated from commit id bdc9c6c7f7.
So macro implementation is modified to fix the error.
Signed-off-by: Prakash PM <prakash.pm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Provides initial support for TI OMAP-L138/DA850 SoC devices on
a Logic PD EVM board.
Provides:
Initial boot and configuration.
Support for i2c.
UART support (console).
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
DA850/OMAP-L138 is a new SoC from Texas Instruments
(http://focus.ti.com/docs/prod/folders/print/omap-l138.html).
This SoC is similar to DA830/OMAP-L137 in many aspects. Hence
rename the da830 specific files and folders to da8xx to
accommodate DA850/OMAP-L138.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
