This chip provides an eDP to LVDS bridge which is useful for SoCs that don't
support LVDS displays (or it would waste scarce pins). The setup is included
in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
While I2C supports multi-master buses this is difficult to get right.
The implementation on the master side in software is quite complex.
Clock-stretching and the arbitrary time that an I2C transaction can take
make it difficult to share the bus fairly in the face of high traffic.
When one or more masters can be reset independently part-way through a
transaction it is hard to know the state of the bus.
This driver provides a scheme based on two 'claim' GPIOs, one driven by the
AP (Application Processor, meaning the main CPU) and one driven by the EC
(Embedded Controller, a small CPU aimed at handling system tasks). With
these they can communicate and reliably share the bus. This scheme has
minimal overhead and involves very little code. It is used on snow to
permit the EC and the AP to share access to the main system PMIC and
battery. The scheme can survive reboots by either side without difficulty.
This scheme has been tested in the field with millions of devices.
Since U-Boot runs on the AP, the terminology used is 'our' claim GPIO,
meaning the AP's, and 'their' claim GPIO, meaning the EC's. This terminology
is used by the device tree bindings in Linux also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new I2C_MUX uclass. Devices in this class can multiplex between
several I2C buses, selecting them one at a time for use by the system.
The multiplexing mechanism is left to the driver to decide - it may be
controlled by GPIOs, for example.
The uclass supports only two methods: select() and deselect().
The current mux state is expected to be stored in the mux itself since
it is the only thing that knows how to make things work. The mux can
record the current state and then avoid switching unless it is necessary.
So select() can be skipped if the mux is already in the correct state.
Also deselect() can be made a nop if required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Document the development flow on figuring out PIRQ information
during the U-Boot porting.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add some documentation on the EFI implementation in U-Boot.
Signed-off-by: Ben Stoltz <stoltz@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The steps required to boot a Linux distribution from U-Boot on x86 are not
very complicated, but it is a good idea to have these written down in an
accessible place.
Document how to examine the boot media from U-Boot, how to load a kernel,
load a ramdisk, set the kernel boot arguments and start the kernel. With
these instructions Ubuntu boots mostly normally on Minnowmax.
Note that the TSC timer does not operate correctly and gives warnings in
the boot log. I expect that ACPI support will solve this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a cpu1 node to the device tree and enable the MP initialization
on QEMU targets (i440fx and q35).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The board manual desribes ON as boolean 1 and OFF as boolean 0.
Updating README with correct boolean values.
Signed-off-by: Raghav Dogra <raghav@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Zynq is using Cadence IP where binding is documented in the Linux kernel
and there is no reason to use different binding.
Synchronize it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The init code for UMC (Unified Memory Controller) and PLL has not
been mainlined yet, but U-boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
FASTBOOT is defined both by CONFIG_USB_FUNCTION_FASTBOOT AND CONFIG_CMD_FASTBOOT, so it doesn't
make much sense to have a CONFIG_USB_FASTBOOT prefix for fastboot-specific options, especially
given that other config options for fastboot use the CONFIG_FASTBOOT prefix.
This replaces the CONFIG_USB_FASTBOOT prefix with CONFIG_FASTBOOT, for consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
USB download gadget functions such as thor and dfu have a separate config option
for the USB gadget part of the code, independent from the command part.
This switches the fastboot USB gadget to the same scheme, for better
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
This introduces a coherent scheme for naming USB download gadget and functions
config options. The download USB gadget config option is moved to
CONFIG_USB_GADGET_DOWNLOAD for better consistency with other gadgets and each
function's config option is moved to a CONFIG_USB_FUNCTION_ prefix.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
We should guide people more strongly towards device tree to avoid the
proliferation of platform data structures. Add documentation to the driver
model README, and also the platform data header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple uclass for LEDs, so that these can be controlled by the device
tree and activated when needed. LEDs are referred to by their label.
This implementation requires a driver for each type of LED (e.g GPIO, I2C).
Signed-off-by: Simon Glass <sjg@chromium.org>
To try to reduce the pain of confusion of binary blobs, add MD5 checksums
for the current versions. This may worsen the situation as new versions
appear, but it should still be possible to obtain these versions, and thus
get a working setup.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The layout of the ROM is a bit hard to discover by reading the code. Add
a table to make it easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable graphics support on Intel Crown Bay board With the help of
vgabios for Intel TunnelCreek IGD. Tested with an external LVDS
panel connected to X4 connector and SDVO adapter connected to X9
connector on the board.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move X86_OPTION_ROM_FILE & X86_OPTION_ROM_ADDR to arch/x86/Kconfig
and rename them to VGA_BIOS_FILE & VGA_BIOS_ADDR which depend on
HAVE_VGA_BIOS. The new names are consistent with other x86 binary
blob options like HAVE_FSP/FSP_FILE/FSP_ADDR.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Document U-Boot multi-processor support as well as configuration
tables like SFI and MP tables for SMP OS kernel.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The word "partition" is doubled. Keep decent forms for the
following lines.
Also, fix some other typos while we are here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
This patch adds the device tree binding doc for the cadence qspi controller &
also removes the not needed properties from the stv0991 device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Now zynq spi driver platform data is controlled by devicetree,
enable the status by saying "okay" on respective board dts to use
the devicetree generated platdata.
Ex:
&spi1 {
status = "okay";
};
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Some AVR32 boards were dropped by the following commits:
9eb45aabe0 (avr32: delete non generic board favr-32-ezkit)
e369307644 (avr32: delete non generic board hammerhead)
c62d2f8fc5 (avr32: delete non generic board mimc200)
e5354b8a9e (avr32: delete non generic board's atstk100{3, 4, 6})
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These defines for a 2nd autoboot stop and delay string are nearly unused. Only
sc3 defines CONFIG_AUTOBOOT_DELAY_STR2. And a patch to remove this most likely
unmaintained board is also posted to the list.
By removing these defines the code will become cleaner and moving the remaining
compile options to Kconfig will get easier.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Before device-tree, the device serial number used to be passed to the kernel
using ATAGs (on ARM). This is now deprecated and all the handover to the kernel
should now be done using device-tree. Thus, this passes the serial-number
property to the kernel using the serial-number property of the root node, as
expected by the kernel.
The serial number is a string that somewhat represents the device's serial
number. It might come from some form of storage (e.g. an eeprom) and be
programmed at factory-time by the manufacturer or come from identification
bits available in e.g. the SoC.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Simon Glass <sgj@chromium.org>
Every pin can be configured now from the device tree. A dt-bindings
has been added to describe the different property available.
Change-Id: I1668886062655f83700d0e7bbbe3ad09b19ee975
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Simon Glass <sjg@chromium.org>
Although the two qemu-x86 targets (i440fx and q35) share a lot in
common, they still have something that cannot easily handled in one
single device tree). Split to create two dedicated device tree files
and make the i440fx be the default build target.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Describe all required properties needed by the irq router device tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
It turns out that QEMU x86 emulated graphic card has a built-in
option ROM which can be run perfectly with native mode by U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Added FIT_LOADABLE_PROP, so the user can identify an optional entry
named "loadables" in their .its configuration. "loadables" is a comma
separated list in the .its
Documentation can be found in doc/uImage.FIT/source_file_format.txt and
doc/uImage.Fit/multi-with-loadables.its
Signed-off-by: Karl Apsite <Karl.Apsite@dornerworks.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Prior to this commit, ZC702 and ZC706 shared the same configuration
and were built as follows:
ZC702: make zynq_zc70x_defconfig && make
ZC706: make zynq_zc70x_defconfig && make DEVICE_TREE=zynq-zc706
This commit introduces separate configuration for them, which makes
the next commit much easier.
Going forward, the recommended build commands are:
ZC702: make zynq_zc702_defconfig && make
ZC706: make zynq_zc706_defconfig && make
Although the old work flow is still supported, CONFIG_TARGET_ZC70X
has been marked as deprecated. If used, the warning message is
shown to prompt users to switch to the new scheme.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit allows users to enable/disable the Freescale NFC
controller found in systems like Vybrid (VF610), MPC5125, MCF54418
or Kinetis K70 via Kconfig with more detailed help docs.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefano Babic <sbabic@denx.de>
[scottwood: updated vf610twr_nand_defconfig]
Signed-off-by: Scott Wood <scottwood@freescale.com>
We really don't want boards defining fixed MAC addresses in their config
so we just remove the option to set it in a fixed way. If you must have
a MAC address that was not provisioned, then use the random MAC address
functionality.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
