Detect the board revision early during boot, and print the decoded
model name.
Eventually, this information can be used for tasks such as:
- Allowing/preventing USB device mode; some models have a USB device on-
board so only host mode makes sense. Others connect the SoC directly
to the USB connector, so device-mode might make sense.
- The on-board USB hub/Ethernet requires different GPIOs to enable it,
although luckily the default appears to be fine so far.
- The compute module contains an on-board eMMC device, so we could store
the environment there. Other models use an SD card and so don't support
saving the environment (unless we store it in a file on the FAT boot
partition...)
Set $fdtfile based on this information. At present, the mainline Linux
kernel doesn't contain a separate DTB for most models, but I hope that
will change soon.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Some configurations have been moved to Kconfig and the difference
among the config headers of UniPhier SoC variants is getting smaller
and smaller. Now is a good time to merge them into a single file.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
There are two kinds of expansion boards which are often used for
the UniPhier platform and they are only exclusively selectable.
It can be better described by the "choice" menu of Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Remove the now unnecessary clocking info from the SoCFPGA
config header. As this info in now used directly in the SPI driver
itself.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Enable support for the DW master SPI controller in the config header
for the SoCFPGA. This controller can only be enabled, if DT support
is enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
With this driver enabled for SoCFPGA, access to SPI NOR flash is
supported.
The configuration (page size, timing info) will be taken from the
DT. See socrates as an example.
This QSPI supports depends on DT. So QSPI is only enabled if
CONFIG_OF_CONTROL is defined (see socfpga_socrates_defconfig).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
The SD supply Voltage was 3.3V on T4240RDB, so enabled 3.3V support for eSDHC.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Wujie Qiu <B49553@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
fm_standard_init() initializes each 10G port by FM_TGEC_INFO_INITIALIZER.
but it needs different implementation of FM_TGEC_INFO_INITIALIZER on different SoCs.
on SoCs earlier(e.g. T4240, T2080), the notation between 10GEC and MAC as below:
10GEC1->MAC9, 10GEC2->MAC10, 10GEC3->MAC1, 10GEC4->MAC2
on SoCs later(e.g. T1024, etc), the notation between 10GEC and MAC as below:
10GEC1->MAC1, 10GEC2->MAC2
so we introduce CONFIG_FSL_FM_10GEC_REGULAR_NOTATION to fit the new SoCs on
which 10GEC enumeration is consistent with MAC enumeration.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.
T1024RDB board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- one 10Gbps XFI interface
- PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors.
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD
- eSPI: 64MB N25Q512 SPI flash.
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- USB: Two Type-A USB2.0 ports with internal PHY
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC
- I2C: Four I2C controllers
- UART: Two UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
T1024QDS is a high-performance computing evaluation, development and
test platform for T1024 QorIQ Power Architecture processor.
T1024QDS board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- Three 1G/2.5Gbps SGMII ports
- Four 1Gbps QSGMII ports
- one 10Gbps XFI or 10Base-KR interface
- SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora
- PCIe: Three PCI Express controllers with five PCIe slots.
- IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- Video: DIU supports video up to 1280x1024x32 bpp.
- Chrontel CH7201 for HDMI connection.
- TI DS90C387R for direct LCD connection.
- Raw (not encoded) video connector for testing or other encoders.
- QUICC Engine block
- 32-bit RISC controller for flexible support of the communications peripherals
- Serial DMA channel for receive and transmit on all serial channels
- Two universal communication controllers, supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- eSPI: Three SPI flash devices.
- SATA: one SATA 2.O.
- USB: Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC.
- I2C: Four I2C controllers.
- UART: Two UART on board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
XFI does not work stable on current board, it's due to heat sink issue,
to make it work stable the board needs additional heat sink, enable two
XFI lanes only. Right now we do not have such an erratum for the issue,
so use a define CONFIG_SYS_FSL_B4860QDS_XFI_ERR to identify it.
The workaround will only be used in XFI protocols and only if the
hwconfig indicates that XFI is prefered.
A new VSC3308 config function is used instead of re-use the original
function, to avoid making the function complex and ugly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Convert T1040QDS and T1040RDB to use generic board code.
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for Cortina CS4315/CS4340 10G PHY.
- This driver loads CS43xx firmware from NOR/NAND/SPI/SD device
to initialize Cortina PHY.
- Cortina PHY has non-standard offset of PHY ID registers, thus
we define own get_phy_id() to override default get_phy_id().
- To define macro CONFIG_PHY_CORTINA will enable this driver.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add configs:
o CONFIG_SYS_GENERIC_BOARD
o CONFIG_DISPLAY_BOARDINFO
in C29XPCIE config header file to use U-boot generic
board code.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add configs:
o CONFIG_SYS_GENERIC_BOARD
o CONFIG_DISPLAY_BOARDINFO
in P1023RDB config header file to use U-boot generic
board code.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
cppcheck reports:
[board/muas3001/muas3001.c:270]: (error) Uninitialized variable: psize
remove the CONFIG_SYS_RAMBOOT define to prevent this error report.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reported-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: York Sun <yorksun@freescale.com>
This define is never set in our setup, so we can remove it safely. The
former code causes cppcheck to complain about:
[board/keymile/km82xx/km82xx.c:311]: (error) Uninitialized variable:
psize
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
Reviewed-by: York Sun <yorksun@freescale.com>
Use generic board architecture for p1010rdb, tested with NOR
boot on p1010rdb-pb.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The define CONFIG_FSL_SATA_V2 is missing, so SATA is not available
in U-boot.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Use generic board architecture for p1025-twr, tested with NOR
boot and NAND boot on p1025-twr.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When device is configured to load RCW from NAND flash IFC_A[16:31] are driven
low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using
IFC_A[16:31] lines are not accessible.
Workaround is already in-place.
Put the errata number to adhere errata handling framework.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable interactive debugging by default. Remove DDR controller interleaving
because this SoC only has one controller. Use auto chip-select interleaving
to detect number of ranks.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Adjust timing for dual-rank UDIMM, verified on M3CQ-8GHS3C0E for speed of
1066, 1333, 1600, 1866MT/s. The 1866 timing is copied to 2133 timing in
case such DIMM comes available.
Also update single-rank 1866 timing. Enable interactive debugging as well.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Shengzhou Liu <Shengzhou.Liu@freescale.com>
add FIT support and set "boardid" from factoryset records
"DEV/id" and "COMP/ver". "boardid" is used for selecting
which fit configuration gets booted on the board.
Signed-off-by: Heiko Schocher <hs@denx.de>
CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION ought to be called
CONFIG_SYS_MMCSD_FS_BOOT_PARTITION to keep it consistent with other config
options such as: CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR.
In addition, it is not related to raw mode booting but to fs mode instead.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
Not every device has multiple MMC slots available, so it makes sense to enable
only the required LDOs for the available slots. Generic code in omap_hsmmc will
enable both VMMC1 and VMMC2, in doubt.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
Some devices may use non-standard combinations of regulators to power MMC:
this allows these devices to provide a board-specific MMC power init function
to set everything up in their own way.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
BeagleBoard-X15 is the next generation Open Source
Hardware BeagleBoard based on TI's AM5728 SoC
featuring dual core 1.5GHZ A15 processor. The
platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x108@60),
separate LCD port, video In port, 4GB eMMC, uSD,
Analog audio in/out, dual 1G Ethernet.
For more information, refer to:
http://www.elinux.org/Beagleboard:BeagleBoard-X15
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
just add a few ifdefs around because this
device is very similar to dra7xxx.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
* Since the emmc isn't always programed trying to load the fs from the
emmc causes boot failures/kernel panic.
* The current bootcmd is set to:
bootcmd=run findfdt; run mmcboot;setenv mmcdev 1; setenv bootpart 1:2; \
setenv mmcroot /dev/mmcblk0p2 rw; run mmcboot;
My guess is the env variables should be set so that sd card boot
(dt,kernel,fs) is the default and then fallback to emmc if it fails (no
sd card detected)
The current bootcmd attempts to set mmcroot to the sd card rootfs but
that code doesn't run due to mmcboot being ran early on.
Signed-off-by: Franklin Cooper Jr. <fcooper@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Out of all OMAP5-like boards, only one of them
needs CONFIG_MISC_INIT_R, so it's best to enable
that for that particular board only, instead of
enabling for all boards unconditionally.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the characters of the error message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the characters of the error message:
"Unknown command '' - try 'help'".
Provide a default size for CONFIG_SYS_PBSIZE so that it can store the error
message and allows the error message to be printed correctly with no hang.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
With enabled console_mux for serial input and usb keyboard sometimes
characters get lost when typing too fast at the serial input (pasting
strings in serial console window). Fix this by using INT_QUEUE for
polling the usb keyboard.
Signed-off-by: Soeren Moch <smoch@web.de>
Add thermal support so that the temperature of the chip can be displayed on
boot:
U-Boot 2015.01-rc1-18268-g1366c05-dirty (Nov 25 2014 - 13:02:42)
CPU: Freescale i.MX6SX rev1.0 at 792 MHz
CPU: Temperature 50 C
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
The fdt_path_offset() checks an alias too.
fdtdec_get_alias_node(blob, "foo") is equivalent to
fdt_path_offset(blob, "foo").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
As well as locating the ROM on the PCI bus, allow the ROM to be supplied to
the emulator. Split the init up a little so that callers can supply their
own interrupt routines. Also allow a vesa mode to be provided, to be
selected once the BIOS run is complete.
Signed-off-by: Simon Glass <sjg@chromium.org>
Intel's Graphics Media Accelerator (GMA) is a generic name for a wide range
of video devices. Add code to set up the hardware on ivybridge. Part of the
init happens in native code, part of it happens in a 16-bit option ROM for
those nostalgic for the 1970s.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some platforms don't have native code for dealing with their video
hardware. In some cases they use a binary blob to set it up and perform
required actions like setting the video mode. This approach is a hangover
from the old PC days where a ROM was provided and executed during startup.
Even now, these ROMs are supplied as a way to set up video. It avoids the
code for every video chip needing to be provided in the boot loader. But
it makes the video much less flexible - e.g. it is not possible to do
anything else while the video init is happening (including waiting hundreds
of milliseconds for display panels to start up).
In any case, to deal with this sad state of affairs, provide an API for
execution of x86 video ROMs, either natively or through emulation.
Signed-off-by: Simon Glass <sjg@chromium.org>
For option ROMs we can use these extensions to request a particular video
mode. Add a header file which defines the binary interface.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some PCI functions cannot be auto-configured. Add a function to set up a
fixed BAR which can be used in these situations. Also add a function to read
the current address of a BAR.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable this option so that we can configure the available PCI devices. Also
make sure that PCI is available early after relocation as we use it for
several other subsystems.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is not needed. Remove it to improve the generic init sequence
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This new symbol may be defined by the compiler. If it is, avoid a compiler
warning when USE_STDINT is defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add simplefb support, note this depends on the kernel having support for
the clocks property which has recently been added to the simplefb devicetree
binding.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Use pre-populated simplefb node under /chosen as
disussed on the devicetree list]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>.
Add a generic helper to fill and enable simplefb nodes.
The first user of this will be the sunxi display code.
lcd_dt_simplefb_configure_node is also a good candidate to be converted
to use this, but that requires someone to run some tests first, as
lcd_dt_simplefb_configure_node does not honor #address-cells and #size-cells,
but simply assumes 1 and 1 for both.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Simon Glass <sjg@chromium.org>
This adds a fixed mode hdmi driver for the sunxi platform. The fixed
mode is a relatively safe 1024x768, more complete EDID handling is
currently not provided. Only HDMI is supported today.
This code is enabled when HPD detects an attached monitor.
Current config is such that 8MB is shaved off at the top of the RAM.
This avoids several memory handling issues, most significant is the fact
that on linux on ARM you are not allowed to remap known RAM as IO. A
clued in display driver will be able to recycle this reserved RAM in
future though.
cfbconsole was chosen as it provides the most important functionality: a
working u-boot console, allowing for the debugging of certain issues
without the need for a UART.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Major cleanups and some small bugfixes]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch enhances the boot of origen board by adding support to ext2, bootz, initrd, bootenv loading and boot script.
It still keeps the previous mmc load command if boot script fails.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
SystemID information could be read through I2C1 from EEPROM
on LS1021ATWR board.
As LS1 is a little-endian processor, getting the version ID by
be32_to_cpu() is wrong. Fix it by using e.version directly.
This change will be compatible for both ARM and PowerPC.
As there is an errata that I2C1 could not work in SD boot,
reading EEPROM through I2C1 is disabled too in SD boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add define CONFIG_SYS_WRITE_SWAPPED_DATA.
For LS1021AQDS and LS1021QTWR nor flash write should swap the
bytes when handle unaligned tail bytes.
Because of the ending, if the date bus width is 16-bits and the
number of bytes is odd, we should swap the byte when write the
last one.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Define USB configs for LS1021XA such as CONFIG_SYS_FSL_USB1_ADDR,
CONFIG_USB_MAX_CONTROLLER_COUNT
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Set TXFIFOTHRESH to adjust ddr pipeline delay for successful large
usb writes
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Implement sata stop command.
This introduces the __sata_stop() weak function, which mirrors
the weak __sata_initialize() function, giving users the option of
undoing the custom steps performed in overrides of sata_initialize().
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Add reset_sata() to the sata driver interface and implement it
for dwc_ahsata. This function cleans up after sata_init(), and
therefore accepts a device number like sata_init() does.
A dummy implementation is provided for the rest of the drivers.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Add arch/arm/cpu/armv7/Kconfig with non-secure and virt options, this is a
preparation patch for adding an env variable to choose between secure /
non-secure boot on non-secure boot capable systems, specifically this
prepares for adding CONFIG_ARMV7_BOOT_SEC_DEFAULT as a proper Kconfig option.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The sandbox/ext4/fat/generic fs commands do not gracefully deal with files
greater than 2GB. Negative values are returned in such cases.
To handle this, the fs functions have been modified to take an additional
parameter of type "* loff_t" which is then populated. The return value
of the fs functions are used only for error conditions.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Update board/gdsys/p1022/controlcenterd-id.c,
drivers/fpga/zynqpl.c for changes]
Signed-off-by: Tom Rini <trini@ti.com>
Change the internal sandbox functions to use loff_t for file offsets.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Change the internal EXT4 functions to use loff_t for offsets.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Update common/spl/spl_ext.c]
Signed-off-by: Tom Rini <trini@ti.com>
Change the internal FAT functions to use loff_t for offsets.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Fix fs/fat/fat.c for min3 updates]
Signed-off-by: Tom Rini <trini@ti.com>
Enable md5sum to obtain the MD5 of the read and written files to check
their contents for validity.
Use map_sysmem() to map buffer in a sandbox environment.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since commit 0defddc851 (config: Add a default CONFIG_SYS_PROMPT),
each board header does not need to define CONFIG_SYS_PROMPT
as long as it uses the default prompt "=> ".
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This macro can be overridden in source files (before including common.h)
and can be used to specify a prefix for debug and error messages. An
example of how to use this is shown below:
#define pr_fmt(fmt) "foo: " fmt
#include <common.h>
...
debug("bar");
The resulting message will read:
foo: bar
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
When enumerating devices, honour the pci_skip_dev() function. This can
be used by PCI controller drivers to restrict which devices will be
probed.
This is required by the NVIDIA Tegra PCIe controller driver, which will
fail with a data abort exception if an access is attempted to a device
number larger than 0 outside of bus 0. pci_skip_dev() is therefore
implemented to prevent any such accesses.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Some filesystems have a UUID stored in its superblock. To
allow using root=UUID=... for the kernel command line we
need a way to read-out the filesystem UUID.
changes rfc -> v1:
- make the environment variable an option parameter. If not
given, the UUID is printed out. If given, it is stored in the env
variable.
- corrected typos
- return error codes
changes v1 -> v2:
- fix return code of do_fs_uuid(..)
- document do_fs_uuid(..)
- implement fs_uuid_unsuported(..) be more consistent with the
way other optional functionality works
changes v2 -> v3:
- change ext4fs_uuid(..) to make use of #if .. #else .. #endif
construct to get rid of unreachable code
Hit any key to stop autoboot: 0
=> fsuuid
fsuuid - Look up a filesystem UUID
Usage:
fsuuid <interface> <dev>:<part>
- print filesystem UUID
fsuuid <interface> <dev>:<part> <varname>
- set environment variable to filesystem UUID
=> fsuuid mmc 0:1
d9f9fc05-45ae-4a36-a616-fccce0e4f887
=> fsuuid mmc 0:2
eb3db83c-7b28-499f-95ce-9e0bb21cda81
=> fsuuid mmc 0:1 uuid1
=> fsuuid mmc 0:2 uuid2
=> printenv uuid1
uuid1=d9f9fc05-45ae-4a36-a616-fccce0e4f887
=> printenv uuid2
uuid2=eb3db83c-7b28-499f-95ce-9e0bb21cda81
=>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
The SPI function does the same thing, so we may as well just use the new
generic function. The 'cs' parameter was not actually used, so can be
dropped.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
This code was not updated when the chip select handling was adjusted. Fix
it to call the correct function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
In some cases we need to manually bind a device to a particular driver.
Add a function to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Add dev_get_parent() as a convenience to obtain the parent of a device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
When the device is created from a device tree node, it matches a compatible
string. Allow access to that string and the associated data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
Move USB Errata checking code from "arch/powerpc" to architecture independent
file "fsl_usb.h" so that errata(s) become independent of the architecture.
For each erratum checking function for PPC arch, define a nop function for
non PPC arch for successful compilation in either case
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable i.MX thermal DM driver to mx6sabre_common.h file. Since the
thermal is used in init_sequence_f, so define the CONFIG_SYS_MALLOC_F_LEN
to support DM driver using in pre relocation phase.
Additional, thermal driver depends on ocotp, make sure to enable
CONFIG_MXC_OCOTP when CONFIG_IMX6_THERMAL is selected.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Add a new thermal uclass for thermal sensor and implement the imx
thermal driver basing on this uclass.
Signed-off-by: Ye.Li <B37916@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Since this function can use up quite a bit of space for its strings, disable
it by default in SPL. Use CONFIG_DM_WARN to re-enable it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Provide a CONFIG_DM_STDIO option to enable registering a serial device
with the stdio library. This is seldom useful in SPL, so disable it by
default when building for SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
For SPL we don't expect to need to remove a device. Save some code space
by dropping this feature. The board config can define
CONFIG_DM_DEVICE_REMOVE if this is in fact needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
The simple malloc() implementation is used when memory is tight. It provides
a simple buffer with an incrementing pointer.
At present the implementation is inside dlmalloc. Move it into its own file
so that it is easier to find.
Rather than using relocation as a signal that the full malloc() is
available, add a special GD_FLG_FULL_MALLOC_INIT flag. This signals that the
simple malloc() should no longer be used.
In some cases, such as SPL, even the code space used by the full malloc() is
wasteful. Add a CONFIG_SYS_MALLOC_SIMPLE option to provide only the simple
malloc. In this case the full malloc is not available at all. It saves about
1KB of code space and about 0.5KB of data on Thumb 2.
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
The faster functions are not actually available in SPL and the code size
likely isn't worth it. Use the normal memcpy() in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert this at91sam9260-based board to use driver model. This should serve
as an example for other similar boards. Serial and GPIO are supported so
far.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Implement SDRAM init using the Memory Reference Code (mrc.bin) provided in
the board directory and the SDRAM SPD information in the device tree. This
also needs the Intel Management Engine (me.bin) to work. Binary blobs
everywhere: so far we have MRC, ME and microcode.
SDRAM init works by setting up various parameters and calling the MRC. This
in turn does some sort of magic to work out how much memory there is and
the timing parameters to use. It also sets up the DRAM controllers. When
the MRC returns, we use the information it provides to map out the
available memory in U-Boot.
U-Boot normally moves itself to the top of RAM. On x86 the RAM is not
generally contiguous, and anyway some RAM may be above 4GB which doesn't
work in 32-bit mode. So we relocate to the top of the largest block of
RAM we can find below 4GB. Memory above 4GB is accessible with special
functions (see physmem).
It would be possible to build U-Boot in 64-bit mode but this wouldn't
necessarily provide any more memory, since the largest block is often below
4GB. Anyway U-Boot doesn't need huge amounts of memory - even a very large
ramdisk seldom exceeds 100-200MB. U-Boot has support for booting 64-bit
kernels directly so this does not pose a limitation in that area. Also there
are probably parts of U-Boot that will not work correctly in 64-bit mode.
The MRC is one.
There is some work remaining in this area. Since memory init is very slow
(over 500ms) it is possible to save the parameters in SPI flash to speed it
up next time. Suspend/resume support is not fully implemented, or at least
it is not efficient.
With this patch, link boots to a prompt.
Signed-off-by: Simon Glass <sjg@chromium.org>
On x86 machines U-Boot needs to be added to a large ROM image which is
then flashed onto the target board. The ROM has a particular format so it
makes sense for U-Boot to build this image automatically. Unfortunately
it relies on binary blobs so we cannot require this for the default
build as yet.
Create a u-boot.rom output file for this purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
This board is a 'bare' version of the existing 'link 'board. It does not
require coreboot to run, but is intended to start directly from the reset
vector.
This initial commit has place holders for a wide range of features. These
will be added in follow-on patches and series. So far it cannot be booted
as there is no ROM image produced, but it does build without errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Many of the x86 CONFIG options will be common across different boards. Move
them to a common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For board IDs a common approach is to set aside several GPIOs for use in
determining the board ID. This can provide information about board features
and the revision.
Add a function that turns a list of GPIOs into an integer by assigning
each GPIO to a single bit.
Signed-off-by: Simon Glass <sjg@chromium.org>
In general we can't store things in the data section until we have inited
SDRAM. Some platforms allow this (e.g. those with SPL) but some don't. Move
the pointer to global_data so that it will work on all platforms.
Without this fix the serial port will not work prior to relocation with
driver model on some platforms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Permit decoding of a named memory region from the device tree. This allows
easy run-time configuration of the address of on-chip SRAM, SDRAM, etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Add an additional function for adding information to the device tree before
booting. This permits additions which are not board-specific.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
The message about needing to reset should be printed no matter what error
is printed. Also, an error should always be printed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
Flash regions can optionally be compressed or hashed. Add the ability to
read this information from the flashmap.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
Use the correct FDT data types for this function. Also add more debugging.
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
This function is useful for ensuring that a node exists. Export it so it
can be used more widely.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
This function can fail if the device tree runs out of space. Rather than
silently booting with an incomplete device tree, allow the failure to be
detected.
Unfortunately this involves changing a lot of places in the code. I have
not changed behvaiour to return an error where one is not currently
returned, to avoid unexpected breakage.
Eventually it would be nice to allow boards to register functions to be
called to update the device tree. This would avoid all the many functions
to do this. However it's not clear yet if this should be done using driver
model or with a linker list. This work is left for later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
This commit replaces roundup macro with the one from Linux Kernel.
DEFINE_ALIGN_BUFFER must be fixed because typechecking can not
be used in this context.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
These macros seem to be useful for U-Boot too (or at least
harmless). Imported from Linux 3.18-rc2.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
U-Boot has imported various utility macros from Linux
scattering them to various places without consistency.
In include/common.h are min, max, min3, max3, ARRAY_SIZE, ALIGN,
container_of, DIV_ROUND_UP, etc.
In include/linux/compat.h are min_t, max_t, round_up, round_down,
etc.
We also have duplicated defines of min_t in some *.c files.
Moreover, we are suffering from too cluttered include/common.h.
This commit moves various macros that originate in
include/linux/kernel.h of Linux to their original position.
Note:
This commit simply moves the macros; the macros roundup,
min, max, min2, max3, ARRAY_SIZE are different
from those of Linux at this point.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
All the references of DIV_ROUND have been replaced with
DIV_ROUND_CLOSEST. Remove DIV_ROUND.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
CONFIG_CPU_ARM1136 was introduced into Kconfig by commit 2e07c249a6
(kconfig: arm: introduce symbol for ARM CPUs).
This commit removes all the defines of CONFIG_ARM1136 and replaces
the only reference in arch/arm/lib/cache.c with CONFIG_CPU_ARM1136.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
CONFIG_CPU_ARM926EJS was introduced into Kconfig by commit 2e07c249a6
(kconfig: arm: introduce symbol for ARM CPUs).
This commit removes all the defines of CONFIG_ARM926EJS and replaces
the only reference in arch/arm/lib/cache.c with CONFIG_CPU_ARM926EJS.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
CONFIG_CPU_ARM920T was introduced into Kconfig by commit 2e07c249a6
(kconfig: arm: introduce symbol for ARM CPUs).
This commit removes all the defines of CONFIG_ARM920T and replaces the
only reference in drivers/usb/host/ohci-hcd.c with CONFIG_CPU_ARM920T.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Some (not all) of ARMv7 boards define CONFIG_ARMV7, which is useless.
Besides, it is never referenced.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add full support for USDHC2, USDHC3, USDHC4 on mx6sx sabresd board.
The default boot socket is USDHC4, so the MMC environment device and
mmcdev variable are set to this device.
Signed-off-by: Ye.Li <B37916@freescale.com>
This is nowhere documented and only used
by two other boards. Replace it with
TQMA6_SPI_FLASH_SECTOR_SIZE.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
mx6sabreauto boards come with 32 MiB of parallel NOR flash.
Add support for it:
U-Boot 2015.01-rc1-18107-g1543636-dirty (Nov 14 2014 - 11:11:04)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: MX6Q-Sabreauto revA
I2C: ready
DRAM: 2 GiB
Flash: 32 MiB
NAND: 0 MiB
Due to pin conflict with I2C3, only define configure I2C3 IOMUX when flash is
not used.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Since USDHC1 and USDHC3 added, the dev index for USDHC2 changed to
1. So modify the default mmcdev in environment variables to dev 1.
Signed-off-by: Ye.Li <B37916@freescale.com>
As auto-negotiation is not supported for 2.5G SGMII, we need
to add a new type PHY_INTERFACE_MODE_SGMII_2500 to differentiate
SGMII-1G and SGMII-2.5G with different setting for auto-negotiation.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add complete USB EHCI support for MPC837XEMDS and MPC837XERDB
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This fixes CPLD timing from previous commit
ab06b236f7.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: This is the difference between v2 and v1 patch]
Reviewed-by: York Sun <yorksun@freescale.com>
a3m071 and a4m2k share one config header. So adding the generic board defines
in this one file is enough to convert both boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
The gdsys hrcon board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 1x GbE (optional)
- Lattice ECP3 FPGA connected via eLBC and PCIe
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
The device id makes u-boot think that this chip needs
cfi_reverse_geometry(), which is not the case.
Add it to jedec_flash, so it is handled properly.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Tune dlvision configuration similar to other gdsys boards to reduce memory
footprint.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
The UBI layer will disable much of its error reporting when it is
compiled into the linux kernel to avoid stopping boot. We want this
error reporting in U-Boot since we don't initialize the UBI layer until
it is used and want the error reporting.
We force this by telling the UBI layer we are building as a module.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
The code for this board supports following features:
- Boot media support: NAND flash/SD card/SPI flash
- Support LCD display (optional, disabled by default)
- Support ethernet
- Support USB mass storage
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The code for this board supports following features:
- Boot media support: NAND flash/SD card/SPI flash
- Support LCD display
- Support ethernet
- Support USB mass storage
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
replaces the at91bootstrap code with SPL code.
make the spl image with:
./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin
this writes the length of the spl image into the 6th
execption vector. This is needed from the ROM bootloader.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
replaces the at91bootstrap code with SPL code.
make the spl image with:
./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin
this writes the length of the spl image into the 6th
execption vector. This is needed from the ROM bootloader.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
erase one nand block in spl code. keep it simple, as size matters
This is used on the upcoming taurus spl support.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
enable to boot only a raw u-boot.bin image from nand with the
CONFIG_SPL_NAND_RAW_ONLY define. This option saves space on
boards where spl space is low.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
move CONFIG_SYS_SPI_WRITE_TOUT into drivers/spi/atmel_spi.h
and define a default value. Delete this define in the board
config files, where it is possible (all boards use currently
the same value).
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This change adds support for enabling the USB host features of the board.
This includes the USB3503A hub and the SMC LAN9730 ethernet controller
as well.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Allow to set the buck voltage for the max77686.
This will be used to reset the SMC LAN9730 ethernet on the odroids.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Compile-time tested only, as I currently don't have access to
the eval board.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
I was running into this limit with a not overly long PXE append line.
Since the PXE code wants to print the resulting command line increase
CONFIG_SYS_PBSIZE too.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This replaces the existing CONFIG_BOOTCOMMAND for exynos5250 and 5420.
exynos4 platforms seem to have existing complex extra env configuration for
booting and so are excluded here. Hence the bootcmd.h is added to
exynos5-common.h.
I have build tested on all exynos platforms (MAKEALL -s exynos), but only boot
tested on arndale.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Guillaume GARDET <guillaume.gardet@free.fr>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
...and remove explicit setting of things which this implies. This is done for
all exynos platforms (4 & 5) so it is added to exynos-common.h
I'm mainly interested in CONFIG_CMD_BOOTZ and CONFIG_SUPPORT_RAW_INITRD
I have build tested on all exynos platforms (MAKEALL -s exynos), but only boot
tested on arndale.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Guillaume GARDET <guillaume.gardet@free.fr>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since, not every board may have all memory channels configured
and all available banks of DMC used, we wish to refactor configs
for Memory Bank size and numbers as per board memory config.
For Example, Peach-Pit has 2GB memory and will be using only 4 banks
but Peach-Pi has 3.5GB memory and will be using all 7 available
SDRAM banks.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This adds following things :
- New config and defconfig for Peach-Pi board.
- Alterations in Kconfig and MAINTAINERS.
- Addition of CONFIG_EXYNOS5800.
- ADdition of exynos5800-peach-pi in dts list.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Common part of config for lager, koelsch, alt and gose board will be able to
replace rcar-gen2-common.h.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The lager, koelsch, alt, gose board supported in rmobile is
distinguished as the R-Car Gen2 series and has much common setting.
This collect up the common part of config as rcar-gen2-common.h.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add pinmux settings, implement board_ehci_hcd_init, board_usb_phy_mode
There are two usb port on mx6sxsabresd board:
1. otg port
2. host port
The following are the connection between usb controller and board usb
interface, host port has not ID pin set:
otg1 core <---> board otg port
otg2 core <---> board host port
In order to make host port work, board_usb_phy_mode return USB_INIT_HOST
to make host port work in HOST mode.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye Li <B37916@freescale.com>
Add pinmux settings, implement board_ehci_hcd_init, board_usb_phy_mode
There are two usb port on mx6slevk board:
1. otg port
2. host port
The following are the connection between usb controller and board usb
interface, host port has not ID pin set:
otg1 core <---> board otg port
otg2 core <---> board host port
In order to make host port work, board_usb_phy_mode return USB_INIT_HOST
to let host port work in host mode.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye Li <B37916@freescale.com>
usb_phy_enable should return status bit, but not phy mode bit, thus
add a new function usb_phy_mode to query the PHY for it's mode and
make usb_phy_enable just return 0 but not 'phy_ctrl & USBPHY_CTRL_OTG_ID'.
Include a new board weak function board_usb_phy_mode. If board code
does not reimplement this function, it just call usb_phy_mode and return
usb_phy_mode's return value. The reason to include such a weak function
is: " SOC OTG core <--connect--> board HOST port, but no pin id for
the board host port, so board can not use usb_phy_mode to return the
phy mode, but define it's own rule."
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye Li <B37916@freescale.com>
Enable these boards mtdparts for nor flash:
p1020rdb-pd, p1021rdb-pc, p1022ds, p1025twr, and p2020rdb-pc.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
This converts all the Keymile powerpc boards to the generic board
initialization.
This includes the 3 Keymile powerpc subsystems: km82xx, km83xx,
and kmp204x.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
* fdt_fixup_mtdparts is called from ft_board_setup
* Run "mtdparts default" to create NAND partition on uboot
* Use mtdparts to create partitions dynamically rather
than using static partitions in device tree
Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
* fdt_fixup_mtdparts is called from ft_board_setup
* run "mtdparts default" to create NAND, NOR partition on uboot
* Use mtdparts to create partitions dynamically rather
than using static partitions in device tree
Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This support of CPLD includes
- Files and register definitions
- Command to switch alternate bank
- Command to switch default bank
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Until now this defined to be 512KB and the total binary size actually
was on the edge of this limit. Most of the powerpc boards have thus
moved to 768KB.
Since on the current kmp204x boards there is 1MB reserved for u-boot on
the SPI boot flash, there is no problem to set the limit to 768KB as
well to be on line with the other powerpc boards and to eventually
configure in some additional features (and binary size) to u-boot.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add initial support for TBS2910 Matrix ARM miniPC.
Support includes MMC, Ethernet, UARTs, HDMI, USB, SATA, PCI, I2C, RTC.
Signed-off-by: Soeren Moch <smoch@web.de>
add the spl info in the header file.
Also, added a macro statement in m6sabre_common.h to avoid compiler
warning.
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
The i.MX6Q/DL sabreauto board has one NAND socket, set the
CONFIG_NAND_MXS and relevant NAND configurations to enable the
MXS NAND flash driver.
Add board level codes to set IOMUX and clock for GPMI-NAND and
BCH module.
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Set the CONFIG_ENV_OFFSET from 384KB to 512KB offset, so we will have larger space
for u-boot image.
When enabling NAND flash support feature, the u-boot image size has exceeded the
384KB, which causes overlay to the environment variables storage.
Signed-off-by: Ye.Li <B37916@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Since kernel 3.15 there are two dtb's for the imx53-qsb board:
imx53-qsb.dtb - For the boards with DA9053 PMIC
imx53-qsrb.dtb - For the boards with MC34708 PMIC
Change the 'fdt_file' dynamically, so that the correct dtb can be used depending
on the board variant.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
U-Boot 2014.10-17457-g0b23780-dirty (Nov 10 2014 - 11:41:04)
CPU: Freescale i.MX6D rev1.2 at 792 MHz
Reset cause: WDOG
Board: ot1200
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected M25P16 with page size 256 Bytes, erase size 64 KiB, total 2 MiB
In: serial
Out: serial
Err: serial
Net: using phy at 0
FEC [PRIME]
Hit any key to stop autoboot: 0
=> usb start
(Re)start USB...
USB0: Port not available.
USB1: USB EHCI 1.00
scanning bus 1 for devices... 4 USB Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 2mA)
|
+-3 Mass Storage (480 Mb/s, 80mA)
| USBest Technology USB Mass Storage Device 0000000000028B
|
+-4 Vendor specific (480 Mb/s, 2mA)
=>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Add support for the 2 ehci controllers found on the sun6i (A31) soc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Marek Vasut <marex@denx.de>
Add proper Kconfig options to select the usb Vbus gpio-s, besides moving to
Kconfig being the right thing to do, an added advantage of this is that it
allows for boards without Vbus gpio-s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add clock_init_safe and clockset_pll5 functions, as these are needed for
SPL support resp. DRAM init (which is needed for SPL too).
Also add some extra clock register constant defines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The A31 uses the AXP221 pmic for various voltages.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
--
Changes in v2:
-Rebase
Changes in v3:
-Add support for all dldo and aldo-s
-Add Kconfig option to select building AXP221 and to select voltage of
dldo and aldo-s
Changes in v4:
-Add axp221_setbits helper function
-Use symbolic names for enabled bits in CTRL1 - CTRL3 registers
This is a MIME GnuPG-signed message. If you see this text, it means that
your E-mail or Usenet software does not support MIME signed messages.
The Internet standard for MIME PGP messages, RFC 2015, was published in 1996.
To open this message correctly you will need to install E-mail or Usenet
software that supports modern Internet standards.
Move CONFIG_DEFAULT_DEVICE_TREE from board config
directly to defconfig.
This patch removes compilation warning:
include/configs/zynq_zybo.h:24:0: warning: "CONFIG_DEFAULT_DEVICE_TREE"
redefined [enabled by default]
#define CONFIG_DEFAULT_DEVICE_TREE zynq-zybo
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
mcc200 and prs200 are old and have no maintainer. Remove the boards.
This also removes the mcc200 specific 1bpp BMP support from
common/lcd.c
Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
This implies that all the km_kirkwood boards and their variants now are
using the generic board init sequence.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
CONFIG_UNIPHIER_SERIAL has been moved to Kconfig and
it is defined in ./.config but not in spl/.config,
so pin_init() should be called from the normal image
so that UART works correctly.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
In the current implementation of the boot sequence of UniPhier
platform, 32KB temporary RAM is available before relocation.
The malloc area and the stack shares the 32KB area.
With CONFIG_SYS_MALLOC_F_LEN set to 0x7000 (28KB), only 0x1000 (4KB)
is left for the stack. In some use cases, the system hangs up
with stack over-flow.
Even with driver-model UART enabled, the malloc area of 0x2000 (8KB)
should be enough.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This patch adds config support needed for ZYBO target and has
been tested on Rev. B ZYBO hardware.
Signed-off-by: Tinghui Wang <steven.wang@digilentinc.com>
[PC changes:
* Dropped boards.cfg change (rebase conflict)
* Dropped custom u-boot env
* Added DTS
* Misc forward-porting changes
]
Signed-off-by: Peter Crosthwiate <crosthwaite.peter@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change clock of SCIF for Alt board is used to external clock.
This changes to using external clock.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
R-Car SoCs of rmobile have same IP of rcar-i2c, and have same address.
This moves rcar-i2c of the address defined to rcar-base.h as common header of
R-Car SoCs.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
R-Car SoCs of rmobile have same IP of sh-i2c, and have same address.
This moves sh-i2c of the address defined to rcar-base.h as common header of
R-Car SoCs, and headers of each SoCs.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Alt board does not use board_late_init function.
This removes this function and define of BOARD_LATE_INIT from config.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Lager board does not use board_late_init function.
This removes this function and define of BOARD_LATE_INIT from config.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Koelsch board does not use board_late_init function.
This removes this function and define of BOARD_LATE_INIT from config.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Gose board has two USB ports, and can use USB EHCI HCD driver of rmobile.
This adds driver settings in order to use this driver.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Gose board has one ether port, this works using sh-ether driver.
This adds GPIO settings and driver settings in order to use the sh-ether.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The header file include/usb.h references ARCH_DMA_MINALIGH and
block_dev_desc_t, thus it must include <asm/cache.h> and <part.h>.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Add example of an USB UDC configuration with DFU and UMS.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Split the Samsung specific PHY control into a separate file
and compile this into the S3C OTG driver only if used on a
Samsung system.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
This patch includes the latest DT sources for socfpga from the current
Linux kernel. And enables CONFIG_OF_CONTROL for the new build target
"socfpga_socrates" (the EBV SoCrates board) to make use of this new DT
support.
Until this patch, the only SoCFPGA U-Boot target in mainline is
"socfpga_cyclone5". This build target is not (yet) changed to support
DT. So nothing changes for this target. Even though the long-term
goal should be to move all SoCFPGA targets over to DT.
One of the reasons to enable DT support in SoCFPGA is, that I need to
support multiple different SPI controllers for this platform. This is
the QSPI Cadence controller and the Designware SPI master controller.
Both are implemented in the SoCFPGA. And enabling both controllers is
only possible by using the new driver model (DM). The DM SPI code
only supports DT based probing. So it was easier to move SoCFPGA to
DT than to add the (deprecated) platform-data based probing to the
DM SPI suport.
Note that the image with the dtb embedded is u-boot-dtb.img. This needs
to be used now for those DT enabled boards instead of u-boot.img.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Add both host and mUSB support.
Currently, the selection between host USB and mUSB is done through the
config file.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
CompuLab cm-t3517 is Computer on Module (CoM) based on AM3517 SoC.
Features: up to 256MB DDR2, up to 512MB NAND, USB hub, mUSB, WiFi, BT,
Analog audio codec, touch screen controller, LED.
Add basic support including:
LED, Serial console, NAND, MMC, GPIO, I2C, 256MB DRAM.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
The keystone2 evm can boot from USB partition with FAT32 FS, so
enable generic load command and fatload command usage.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
The Multicore Software Development Kit (MCSDK) provides foundational
software for TI KeyStone II device platforms. It's supposed to be used
with uboot, and it's convenient to have the same names for images, so
correct environment image names according to the last MCSDK3.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Currently to customize env for various ks2 boards, individual
variables such as NAME_FS etc are defined and included in the
common config.h to define CONFIG_EXTRA_ENV_SETTINGS. This
doesn't scale well if a variable is not applicable on a
specific board. Using this scheme, we have to define variables
with empty value and it's ugly. Instead, to allow board specific
customization of default env variable, define a common
CONFIG_EXTRA_ENV_KS2_SETTINGS for all common variables and define
board specific variables in individual board specific config.h
using CONFIG_EXTRA_ENV_KS2_BOARD_SETTINGS. Use the common and board
specific variables to define CONFIG_EXTRA_ENV_SETTINGS. This way
more variables can be added in future for individual boards
without affecting the other config.h files.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
To allow out of box demo, change default boot mode to ubi
boot now that NAND is functional in latest EVMs.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Keystone2 Lamar SoC uses the same keystone SerDes driver.
All Keystone2 EVM boards currently use SerDes driver, so move
CONFIG_TI_KEYSTONE_SERDES to common configuration file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Add a driver for the designware serial UART used on sunxi. This just
redirects to the normal ns16550 driver.
Add a stdout-path to the device tree so that the correct UART is chosen.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This adds driver model support to the sunxi GPIO driver, using the device
tree to trigger binding of the driver. The driver will still operate
without driver model too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
For now we won't want to mess with the existing configurations. Create a
new one which will enable device tree and driver model. Note that this
brings the device tree binary into u-boot-sunxi-with-spl.bin.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
These are from Linux 3.17-rc7 (commit fe82dcec). U-Boot only uses a small
portion of these, but we may as well have something to look forward to.
The total compiled size is about 25KB.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Mostly automatic with:
sed -i -e 's/CONFIG_\(SUN[45678]I\)/CONFIG_MACH_\1/g' $(git grep -l CONFIG_SUN[45678]I)
followed by removing the relevant #defines from include/configs/sun?i.h by
hand.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This adds support for USB commands and USB storage device.
Signed-off-by: Yoshiyuki Ito <yoshiyuki.ito.ub@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
If CONFIG_RMOBILE_EXTRAM_BOOT is enabled, U-Boot is booted from External RAM.
The default boot address is 0x70000000.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
If CONFIG_RMOBILE_EXTRAM_BOOT is enabled, U-Boot is booted from External RAM.
The default boot address is 0x70000000.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
If CONFIG_RMOBILE_EXTRAM_BOOT is enabled, U-Boot is booted from External RAM.
The default boot address is 0xB0000000.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
155fa9af95 "spi: mxc: fix sf probe when using mxc_spi" break
spi flash detection on the aristainetos board. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
On mx6 sabreauto board, there are two USB ports:
0: OTG
1: HOST
The EHCI driver is enabled for this board, but the IOMUX and VBUS power
control is not implemented, which cause both USB port failed to work.
This patch fix the problem by adding the board support codes.
Since the power control uses the GPIO pin from port expander MAX7310,
the PCA953X driver is enabled for accessing the MAX7310.
The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting
its daisy chain. Add a new function "imx_iomux_set_gpr_register" to
handle GPR register setting.
Signed-off-by: Ye.Li <B37916@freescale.com>
There are three SD/MMC sockets on mx6slevk boards. Implements the
full support for them.
The default boot socket is USDHC2, so the MMC environment is set
to that device.
Signed-off-by: Ye.Li <B37916@freescale.com>
Set the CONFIG_MXC_GPT_HCLK configuration in mx6_common.h, so that
24Mhz OSC clock source will be selected for GPT on all MX6 platforms.
Signed-off-by: Ye.Li <B37916@freescale.com>
Add new Kconfig option to let the user select the targets
endianess. Each target have to select SUPPORTS_BIG_ENDIAN
and/or SUPPORTS_LITTLE_ENDIAN to indicate which endianess
is supported.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add example config file entry for the Altera SPI controller. This SPI
controller can also, under special conditions, be used to operate the
EPCS/EPCQ SPI NOR.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
[1] arch/arm/include/asm/arch-at91/at91_shdwn.h
The top9000 was the last board to use this header file.
It was removed by commit d58a9451e7 (ppc/arm: zap EMK boards).
[2] board/matrix_vision/common/*
Some Matrix Vision boards were dropped by commit e7a565638a
(powerpc: mpc83xx: remove board support for MERGERBOX and MVBLM7)
and commit af55e35d33
(powerpc: mpc5xxx: remove board support for MVBC_P and MVSMR).
Since then these files have been unused.
[3] include/usb/omap1510_udc.h
The omap5912osk was the last board to use this header file.
It was removed by commit 62d636aa2a
(omap: remove omap5912osk board support).
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-By: Wolfgang Denk <wd@denx.de>
This enables the VMMC2 LDO, which powers the MMC2 device.
When the device starts from MMC2, this has already been enabled by the BootROM,
but when starting from peripheral boot (USB, UART), it is not the case.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The patch below failed to define the variable, so define it
to make it consistent with M53EVK.
commit a428ac914b
Author: Lothar Rubusch <lothar@denx.de>
Date: Thu Jun 26 11:01:29 2014 +0200
ARM: m28evk: Update default environment
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Commit 155fa9af95 changed the way
to define a GPIO line, which can be used to force CS high
across multiple transactions. In order to fix sf detection
change board code to make use of board_spi_cs_gpio(..).
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
This patch adds I2C support for the SoCFPGA. Using the designware I2C
controller driver. It supports all 4 I2C busses on the SoCFPGA.
The designware I2C driver has now been converted to the
CONFIG_SYS_I2C framework. So lets enable it on SoCFPGA.
Tested on SoCrates.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Add support for the Kosagi Novena board. Currently supported are:
- I2C busses
- FEC Ethernet
- MMC0, MMC1, Booting from MMC
- SATA
- USB ports
- USB Ethernet
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Nikolay Dimitrov <picmaster@mail.bg>
Reviewed-by: Nikolay Dimitrov <picmaster@mail.bg>
The code density of x86_64 is not wonderful. Increase the maximum boot
size and adjust the load address to cope.
Signed-off-by: Simon Glass <sjg@chromium.org>
In preparation for the SoCFPGA support of the designware I2C driver,
convert this driver to the common CONFIG_SYS_I2C framework.
This patch converts all users of this driver, this is:
- ST spearxxx boards
- AXS101 (ARC700 platform)
I couldn't test this patch on those boards. Only compile tested for all
spear boards. And tested on SoCFPGA.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
This patch just converts the function prototypes used throughout
this driver to match those of the i2c framework. There is so far
no functional change. This patch does not do the deeper integration
of the framework bits.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This is a bit odd in that we are permitted to boot images for either, even
though they are separate architectures.
Signed-off-by: Simon Glass <sjg@chromium.org>
The following bard configurations have been without active maintenance
for a long time, and the board maintainer agrees to have them removed:
MPC5200: TOP5200, MINI5200, EVAL5200
MPC860: TOP860
at91sam9xeXXX: top9000eval_xe, top9000su_xe
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
[trini: Add missing Kconfig removals]
Signed-off-by: Tom Rini <trini@ti.com>
This config is required by Odroid, and could be also useful for the other
boards.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some boards still use xstr(). Replace remaining occurrences
of xstr() by commonly used __stringify().
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Enable EXT support in SPL for OMAP4 boards.
Build tested for duovero, omap4_sdp4430 and omap4_panda.
Run time tested on omap4_panda.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@ti.com>
Add EXT filesystem support to SPL.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
[trini: Fix a warning and checkpatch problems]
Signed-off-by: Tom Rini <trini@ti.com>
Rename some defines containing FAT in their name to be filesystem generic:
MMCSD_MODE_FAT => MMCSD_MODE_FS
CONFIG_SPL_FAT_LOAD_ARGS_NAME => CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME => CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION => CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@ti.com>
Use inttypes.h and uint64_t to correct the code so that it will not issue
warnings on 64-bit machines where 'uint64_t' is 'unsigned long'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Unfortunately 'unsigned long long' and 'uint64_t' are not necessarily
compatible on 64-bit machines. Use the correct typedef instead of
writing the supposed type out in full.
Signed-off-by: Simon Glass <sjg@chromium.org>
inttypes.h defines format specifiers for printf which work with data types of
particular sizes. stdlib.h is currently just a passthrough to malloc.h which
has declarations of the various *alloc functions.
Add the required #define to common.h so that these printf format specifiers
will be made available.
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
(Replaced with a GPL version from glibc)
There's a definition in stdint.h (provided by gcc) which will be more correct
if available.
Define CONFIG_USE_STDINT to use this feature, or USE_STDINT=1 on the 'make'
commmand.
This adjusts the settings for x86 and sandbox, with both have 64-bit options.
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@google.com>
Rewritten to be an option, since stdint.h is often available only in glibc.
Changed to preserve a clear boundary between stdint and non-stdint
Signed-off-by: Simon Glass <sjg@chromium.org>
The run command treats each argument an an environment variable. It gets the
value of each variable and executes it as a command. If an environment
variable contains a newline and the hush cli is used, it is supposed to
execute each line one after the other.
Normally a newline signals to hush to exit - this is used in normal command
line entry - after a command is entered we want to return to allow the user
to enter the next one. But environment variables obviously need to execute
to completion.
Add a special case for the execution of environment variables which
continues when a newline is seen, and add a few tests to check this
behaviour.
Note: it's not impossible that this may cause regressions in other areas.
I can't think of a case but with any change of behaviour with limited test
coverage there is always a risk. From what I can tell this behaviour has
been around since at least U-Boot 2011.03, although this pre-dates sandbox
and I have not tested it on real hardware.
Reported-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
This board is old and is using CONFIG_I2C_X, which is wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board is old and is using CONFIG_I2C_X, which is wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board is old and is using CONFIG_I2C_X, which is wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This is the only used of CONFIG_SPI_X macro, just zap this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Remove this board as this is the only one last user of eeprom_probe(),
which is pretty non-standard stuff.
This patch also removes all the PHP, SQL and CSS stuff from U-Boot,
which probably makes U-Boot a bit less IoT ;-)
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board uses eeprom accessors in an incorrect way. The board
is old and unsupported, just zap it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board is the only user of CONFIG_SYS_EEPROM_X40430 , remove
it so the EEPROM command code can be cleansed of the related code
as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
The file board/Marvell/include/mv_gen_reg.h is incompatible with
the GPL (see for example the "MARVELL RESERVES THE RIGHT AT ITS SOLE
DISCRETION TO REQUEST THAT THIS CODE BE IMMEDIATELY RETURNED TO
MARVELL" clause). As this cannot be fixed, we remove the file and all
code that depends on it. Fortunately this only affects some very old
boards that have long reached EOL:
CPCI750
DB64360
DB64460
p3m750
p3m7448
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Add example configuration stub for the DWC2 USB controller.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Pavel Machek <pavel@denx.de>
This is not used anywhere, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Switch to the common spl.h file and zap the arch/spl.h . Since the arch/spl.h
contained various ad-hoc symbols, zap those symbols as well and rework the
board configuration a little so it doesn't depend on them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Pavel Machek <pavel@denx.de>
Move this initialization code to proper place. The misc_init_r()
function is called way too late and the platform initialization
code should be executed much earlier.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Pavel Machek <pavel@denx.de>
U-Boot does not have arch/arm/kernel, include/uapi directories,
This commit copies files as follows:
Location in Linux -> Location in U-Boot
arch/arm/kernel/debug.S -> arch/arm/lib/debug.S
arch/arm/include/debug/8250.S -> arch/arm/include/debug/8250.S
include/uapi/linux/serial_reg.h -> include/linux/serial_reg.h
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
I was running into this limit with a not overly long PXE append line.
Since the PXE code wants to print the resulting command line increase
CONFIG_SYS_PBSIZE too.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The A23 only has UART0 muxed with MMC0. Some of the boards we
encountered expose R_UART as a set of pads.
Add support for R_UART so we can have a console while using mmc.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The basic blocks of the A23 are similar to the A31 (sun6i). Re-use
sun6i code for initial clock, gpio, and uart setup.
There is no SPL support for A23, as we do not have any documentation
or sample code for DRAM initialization.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Allwinner SoCs provide uart0 muxed with mmc0, which can then be used
with a micro SD breakout board. On the A23, this is the only way to
use uart0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
BOOT_TARGET_DEVICES includes MMC unconditionally. This breaks when
CONFIG_CMD_MMC is not defined. Use a secondary macro to conditionally
include it when CONFIG_MMC is enabled, as we do for CONFIG_AHCI.
This is used when we want to use uart0 from port F, which conflicts
with mmc0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Many people are still using old linux-sunxi-3.4 kernels on sunxi devices,
adding the proper MACH_TYPE defines for this allows people to switch to
upstream u-boot, so that we can stop maintaining the linux-sunxi u-boot fork.
These machine-ids are all properly registered at:
http://www.arm.linux.org.uk/developer/machines/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a new sun6i machine that supports UART and MMC.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: use SPDX labels, adapt to Kconfig system, drop ifdef
around mmc and smp code, drop MACH_TYPE]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
BOOT_TARGET_DEVICES includes USB unconditionally. This breaks when
CONFIG_CMD_USB is not defined. Use a secondary macro to conditionally
include it when CONFIG_EHCI is enabled, as we do for CONFIG_AHCI.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This commit converts UniPhier on-chip serial driver to driver model.
Since UniPhier SoCs do not have Device Tree support, some board files
should be added under arch/arm/cpu/armv7/uniphier/ph1-*/ directories.
(Device Tree support for UniPhier platform is still under way.)
Now the base address and master clock frequency are passed from
platform data, so CONFIG_SYS_UNIPHIER_SERIAL_BASE* and
CONFIG_SYS_UNIPHIER_UART_CLK should be removed.
Tested on UniPhier PH1-LD4 ref board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
The functions _serial_putc, _serial_putc_raw, _serial_puts,
_serial_getc, _serial_tstc, _serial_setbrg are defined and used
locally in each of serial_ns16550.c and serial_s3c24x0.c.
Add static directive to them and remove declarations from
include/common.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
The platform_data definitions are generally referenced from both
drivers and board files. That is why header files defining
platform_data sturectures are placed in "include" directory,
but our top level "include" directory is already too cluttered.
Let's collect platform_data definitions under the directory
"include/dm/platform_data" like Linux gathers ones around under
"include/linux/platform_data".
This commit moves two header files:
include/serial_mxc.h -> include/dm/platform_data/serial_mxc.h
include/serial_pl01x.h -> include/dm/platform_data/serial_pl01x.h
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Convert over this driver, using device tree to pass in the required
information. The peripheral is still probed, just the number of GPIO banks
and their offsets is in the device tree (previously this was a table in
the driver).
Signed-off-by: Simon Glass <sjg@chromium.org>
These ended up in arch/arm/dts/dt-bindings temporarily, but in fact the
correct place is now include/dt-bindings. Move them to be consistent.
Signed-off-by: Simon Glass <sjg@chromium.org>
Check the state of the malloc() heap before each test is run, so that tests
can verify that all is well at the end. Provide helper functions to mark
the heap and to check that it returns to its initial state.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have several GPIO drivers now and all are doing similar things to record
which GPIOs are reserved.
Move this logic into the uclass to make the drivers similar.
We retain the request()/free() methods since currently one driver does use
these for setting up the pin.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust the configuration for the am33xx boards, including beagleboard,
to use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
Adjust the configuration for the am33xx boards, including beaglebone black
to use driver model.
This can be extended to other OMAP boards once platform data is provided
for them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
It is inconvenient to have to use casts when specifying platform data. Also
it is not strictly correct, since we should use map_sysmem() to convert an
address to a pointer.
Adjust the platform data to use an address.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Fix the following build warning by including linux/compat.h:
include/linux/usb/musb.h:110: warning: 'struct device' declared inside
parameter list
include/linux/usb/musb.h:110: warning: its scope is only this definition
or declaration, which is probably not what you want
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
The private libgcc is supported only on ARM, MIPS, PowerPC, SH, x86.
Those architectures should "select" HAVE_PRIVATE_LIBGCC and
CONFIG_USE_PRIVATE_LIBGCC should depend on it.
Currently, this option is enabled on Tegra boards and x86 architecture.
Move the definition from header files to Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
CONFIG_SYS_HZ is always defined as 1000 in config_fallbacks.h
(but some boards still have redundant definitions).
This commit moves the definition and the document in README to
Kconfig. Since lib/Kconfig can assure that CONFIG_SYS_HZ is 1000,
the sanity check in lib/time.c should be removed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Marek Vasut <marex@denx.de>
By using CONFIG_ENV_IS_IN_FAT it's far easier
to have a private, minimal environment for e.g.
booting off of network or mounting rootfs on NFS
without having to modify the configuration header.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add ddr3 commands:
test <start_addr in hex> <end_addr in hex> - test DDR from start\n
address to end address\n
ddr compare <start_addr in hex> <end_addr in hex> <size in hex> -\n
compare DDR data of (size) bytes from start address to end
address\n
ddr ecc_err <addr in hex> <bit_err in hex> - generate bit errors\n
in DDR data at <addr>, the command will read a 32-bit data\n
from <addr>, and write (data ^ bit_err) back to <addr>\n
Delete CONFIG_MAX_UBOOT_MEM_SIZE, as it was supposed to be used
for ddr3 commands and for now it's not needed any more.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Keystone2 Edison SoC uses the same keystone SerDes driver.
This patch adds support for K2E SoCs.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The phy framework has function to get link, so use it
instead of own implementation.
There is no reason to check SGMII link while sending each
packet, phy link is enough. Check SGMII link only while
ethernet open.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
As MDIO bus has been added we can register PHYs with it.
After registration, the PHY driver will be probed according to the
hardware on board.
Startup PHY at the ethernet open.
Use phy_startup() instead of keystone_get_link_status() when eth open,
as it verifies PHY link inside and SGMII link is checked before.
For K2HK evm PHY configuration at init was absent, so don't enable
phy config at init for k2hk evm.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
SerDes driver is used by other sub systems like PCI, sRIO etc.
So modify it to be more general. The SerDes driver provides common
API's that can also be extended for other peripherals SerDes
configurations.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Enhance the driver to use cmu/comlane/lane specific configurations
instead of 1 big array of configuration.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch split the Keystone II SGMII SerDes related code from
Ethernet driver and create a separate SGMII SerDes driver.
The SerDes driver can be used by others keystone subsystems
like PCI, sRIO, so move it to driver/soc/keystone directory.
Add soc specific drivers directory like in the Linux kernel.
It is going to be used by keysotone soc specific drivers.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The header file for the driver should be in correct place.
So move it to "arch/arm/include/asm/ti-common/keystone_net.h"
and correct driver's external dependencies. At the same time
align and correct some definitions.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Currently the network driver is used only by k2hk evm board.
The k2hk SoC contains NETCP v1.0, but Keystone2 SoCs, like k2e
contain NETCP v1.5. So driver should be able to work with such kind
of NETCP. This commit adds this opportunity. The main difference in
masks and some registers, the logic is the same, so only definitions
should be changed. To differentiate between versions add KS2_NETCP_V1_0
and KS2_NETCP_V1_5. Also remove unused and no more needed defines.
The port number is specific for each board so move this parameter to
configuration.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Currently keystone has misc_init_r where all DSPS are turned off
by default. So enable this function.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Add support of usb xhci. xHCI controls all USB speeds of the Host
mode, that is, the SS through the SS PHY, as well as the HS, FS, and
LS through the USB2 PHY. xHCI replaces and supersedes all previous
host HCIs (HS-only EHCI, FS/LS OHCI and UHCI), and is therefore not
backwards compatible with any of them. The USB3SS’s USB Controller is
fully compliant with xHC.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The keystone_nav driver is general driver intended to be used for
working with queue manager and pktdma for different IPs like NETCP,
AIF, FFTC, etc. So the it's API shouldn't be named like it works only
with one of them, it should be general names. The names with prefix
like netcp_* rather do for drivers/net/keystone_net.c driver. So it's
good to generalize this driver to be used for different IP's and
delete confusion with real NETCP driver.
The current netcp_* functions of keystone navigator can be used for
other settings of pktdma, not only for NETCP. The API of this driver
is used by the keystone_net driver to work with NETCP, so net driver
also should be corrected. For convenience collect pkdma
configurations in drivers/dma/keystone_nav_cfg.c.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The keystone_nav is used by drivers/net/keystone_net.c driver to
send and receive packets, but currently it's placed at keystone
arch sources. So it should be in the drivers directory also.
It's separate driver that can be used for sending and receiving
pktdma packets by others drivers also.
This patch just move this driver to appropriate directory and
doesn't add any functional changes.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The maxBCM board is equipped with the Marvell Armada-XP MV78460 SoC. It
integrates an SPI NOR flash and an Marvell 88E6185 switch.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds basic support for the Marvell DB-MV784MP-GP evaulation
board. This is the first board that uses the recently created
Armada XP 78460 SoC support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
The Marvell MV78460 eval board DB-78460-BP seems to need a longer
PHY autonegotiation timeout than the "standard" 4 seconds. So lets
make this timeout configurable. If not defined in the board config
header the original 4000ms is used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
This patch adds support for the NETA ethernet controller which is integrated
in the Marvell Armada XP SoC's. This port is based on the Linux driver which
has been stripped of the in U-Boot unused portions.
Tested on the Marvell MV78460 eval board db-78460-bp.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Tested-by: Luka Perkov <luka@openwrt.org>
These mbus functions are ported from Barebox. The Barebox version is
ported from Linux. These functions will be first used by the upcoming
Armada XP support. Later other Marvell SoC's will be adopted to use
these functions as well (Kirkwood, Orion).
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Commit 155fa9af95 changed the way
to define a GPIO line, which can be used to force CS high
across multiple transactions. In order to fix sf detection
change board code to make use of board_spi_cs_gpio(..).
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Enable FIT support and the bootelf command. Also change the default load
address to somewhere other than the normal load address of the kernel,
to allow for decompression without overwriting the original file.
Signed-off-by: Simon Glass <sjg@chromium.org>
To get a display in U-Boot on link you must either build a coreboot that
always sets it up, or use Esc-Refresh-Power to reset the machine.
When we do have a display, it is nice to display the model at the top, so
enable this option.
Signed-off-by: Simon Glass <sjg@chromium.org>
We may as well use hush. The auto-complete option was incorrect so this was
not enabled. Also expand the command line size a little and go back to the
default prompt since "boot>" doesn't seem any more useful.
Signed-off-by: Simon Glass <sjg@chromium.org>
The fdt_for_each_subnode() iterator macro provided by this patch can be
used to iterate over a device tree node's subnodes. At each iteration a
loop variable will be set to the next subnode.
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The fdtdec_pci_get_bdf() function returns the bus, device, function
triplet of a PCI device by parsing the "reg" property according to the
PCI device tree binding.
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the fdt_get_resource() and fdt_get_named_resource() functions which
can be used to parse resources (memory regions) from an FDT. A helper to
compute the size of a region is also provided.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Given a device tree node, a property name and an index, the new function
fdt_get_string_index() will return in an output argument a pointer to
the index'th string in the property's value.
The fdt_get_string() is a shortcut for the above with the index being 0.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Given a device tree node and a property name, the new fdt_find_string()
function will look up a given string in the string list contained in the
property's value and return its index.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Given a device tree node and a property name, the fdt_count_strings()
function counts the number of strings found in the property value.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
USB support must be enabled before config_distro_bootcmd.h is included
for bootcmd to include USB-related functionality.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The built-in SMSC 95xx chip doesn't know its own MAC address. Instead,
we must query it from the VC firmware; it's probably encoded in fuses
on the BCM2835.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Enable DWC2 USB, storage and ethernet support. Tested on RPi B+.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
This is the USB host controller used on the Altera SoCFPGA and Raspbery Pi.
This code has three checkpatch warnings, but to make sure it stays at least
readable and clear, these are not fixed. These bugs are in the USB request
handling combinatorial logic, so any abstracting of those is out of question.
Tested on DENX MCV (Altera SoCFPGA 5CSFXC6C6U23C8N) and RPi B+ (BCM2835).
Signed-off-by: Oleksandr Tymoshenko <gonzo@bluezbox.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Vince Bridgers <vbridger@altera.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Adjust the driver so that leaf functions take a pointer to the serial port
register base. Put all the global configuration in the init function, and
use the same settings from then on.
This makes it much easier to move to driver model without duplicating the
code, since with driver model we use platform data rather than global
settings.
The driver is compiled with either the CONFIG_PL010_SERIAL or
CONFIG_PL011_SERIAL option and this determines the uart type. With driver
model this needs to come in from platform data, so create a new
CONFIG_PL01X_SERIAL config which brings in the driver, and adjust the
driver to support both peripheral variants.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Convert the BCM2835 GPIO driver to use driver model, and switch over
Raspberry Pi to use this, since it is the only board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Now that serial and GPIO are available for iMX.6, move cm_fx6 over as an
example.
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Add driver model support with this driver. Boards which use this driver
should define platform data in their board files.
Signed-off-by: Simon Glass <sjg@chromium.org>
The U_BOOT_DEVICE macro allows the declaration of a single U-Boot device.
Add an equivalent macro to declare an array of devices, for convenience.
Signed-off-by: Simon Glass <sjg@chromium.org>
The existing ll_entry_declare() permits a single element of the list to
be added to a linker list. Sometimes we want to add several objects at
once. To avoid lots of messy declarations, add a macro to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust this driver to use driver model and move smdk5420 boards over to
use it.
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust the sandbox cros_ec emulation driver to work with driver model, and
switch over to driver model for sandbox cros_ec.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add support for driver model if enabled. This involves minimal changes
to the code, mostly just plumbing around the edges.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This converts the Tegra SPI drivers to use driver model. This is tested
on:
- Tegra20 - trimslice
- Tegra30 - beaver
- Tegra124 - dalmore
(not tested on Tegra124)
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Use driver model for exynos5 board SPI flash.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Convert sandbox's spi flash emulation driver to use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add a driver model uclass for SPI flash which supports the common
operations (read, write, erase). Since we must keep support for the
non-dm interface, some modification of the spi_flash header is required.
CONFIG_DM_SPI_FLASH is used to enable driver model for SPI flash.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Since spi_flash.h is supposed to be the public API for SPI flash, move
private things to sf_internal.h. Also tidy up a few comment nits.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Adjust this board to use the driver model soft_spi implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Move the exynos SPI driver over to driver model. This removes quite a bit
of boilerplate from the driver, although it adds some for driver model.
A few device tree additions are needed to make the SPI flash available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This feature provides for init of a single SPI port for the soft SPI
feature. It is not really compatible with driver model since it assumes a
single SPI port. Also, inserting SPI init into the driver by means of
a #define is not very nice.
This feature is not used by any active boards, so let's remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Adjust the sandbox SPI driver to support driver model and move sandbox over
to driver model for SPI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
U-Boot includes a SPI emulation driver already but it is not explicit, and
is hidden in the SPI flash code.
Conceptually with sandbox's SPI implementation we have a layer which
creates SPI bus transitions and a layer which interprets them, currently
only for SPI flash. The latter is actually an emulation, and it should be
possible to add more than one emulation - not just SPI flash.
Add a SPI emulation uclass so that other emulations can be plugged in to
support different types of emulated devices on difference buses/chip
selects.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add a uclass which provides access to SPI buses and includes operations
required by SPI.
For a time driver model will need to co-exist with the legacy SPI interface
so some parts of the header file are changed depending on which is in use.
The exports are adjusted also since some functions are not available with
driver model.
Boards must define CONFIG_DM_SPI to use driver model for SPI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
(Discussed some follow-up comments which will address in future add-ons)
The sequence number is unique within the uclass, so state this clearly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Buses sometimes want to pass data to their children when they are probed.
For example, a SPI bus may want to tell the slave device about the chip
select it is connected to.
Add a new function to permit the parent data to be supplied to the child.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Buses need to iterate through their children in some situations. Add a few
functions to make this easy.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Convert the exynos GPIO driver to driver model. This implements the generic
GPIO interface but not the extra Exynos-specific functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
The generic board deadline is approaching, and we need this feature to
enable driver model. Enable CONFIG_SYS_GENERIC_BOARD for s5p_goni.
Signed-off-by: Simon Glass <sjg@chromium.org>
The generic board deadline is approaching, and we need this feature to
enable driver model. Enable CONFIG_SYS_GENERIC_BOARD for smdkc100.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add proper initialization of GPIO pins used by software i2c.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
The driver model supports two ways for passing device parameters;
Device Tree and platform_data (board file).
Each driver should generally support both of them because some
popular IPs are used on various platforms.
Assume the following scenario:
- The driver Foo is used on SoC Bar and SoC Baz
- The SoC Bar uses Device Tree control (CONFIG_OF_CONTROL=y)
- The SoC Baz does not support Device Tree; uses a board file
In this situation, the device driver Foo should work with/without
the device tree control. The driver should have .of_match and
.ofdata_to_platdata members for SoC Bar, while they are meaningless
for SoC Baz; therefore those device-tree control code should go
inside #ifdef CONFIG_OF_CONTROL.
The driver code will be like this:
#ifdef CONFIG_OF_CONTROL
static const struct udevice_id foo_of_match = {
{ .compatible = "foo_driver" },
{},
}
static int foo_ofdata_to_platdata(struct udevice *dev)
{
...
}
#endif
U_BOOT_DRIVER(foo_driver) = {
...
.of_match = of_match_ptr(foo_of_match),
.ofdata_to_platdata = of_match_ptr(foo_ofdata_to_platdata),
...
}
This idea has been borrowed from Linux.
(In Linux, this macro is defined in include/linux/of.h)
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
The header files include/dm/platdata.h and include/dm/uclass.h
use ll_entry_declare(); therefore they depend on
include/linker_lists.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
The header file include/linker_lists.h uses __aligned();
therefore it depends on include/linux/compiler.h
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
The struct udevice stands for a device, not a driver.
The driver_info.name is a driver's name, which is referenced
to bind devices.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Update Apalis T30 as per the following commits
c369139234
tegra: dts: Add serial port details
461be2f96e
kconfig: remove redundant "string" type in arch and board Kconfigs
f1ef2b6233
kconfig: move CONFIG_DEFAULT_DEVICE_TREE to kconfig
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Clean-up a spurious new line which got introduced resp. left behind by
commit
f1ef2b6233
kconfig: move CONFIG_DEFAULT_DEVICE_TREE to kconfig
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Wondering what exactly that one should bring (;-p). Looks like a remnant of the last commit
783e6a72b8
kconfig: move CONFIG_OF_* to Kconfig
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use architecture specific memcpy to speed up things.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds board support for the Toradex Apalis T30 a computer on
module which can be used on different carrier boards.
For the sake of ease of use we do not distinguish between different
carrier boards for now as the base module features are deemed
sufficient enough for regular booting.
The following functionality is working so far:
- eMMC boot and environment storage
- Gigabit Ethernet (once Thierry's PCIe as well as my E1000 resp. i210
fixes hit mainline)
- MMC/SD cards (both 8-bit as well as 4-bit slot)
- USB client/host (dual role port as client e.g. for DFU/UMS, other two
ports as host)
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a new setup@ section to the FIT which can be used to provide a setup
binary for booting Linux on x86. This makes it possible to boot x86 from
a FIT.
Signed-off-by: Simon Glass <sjg@chromium.org>
HDMI config options can be placed into the common mx6sabre_common.h file to
avoid duplication.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enable blob commands for platforms having SEC 4.0 or greater
for secure boot scenarios
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's SEC block has built-in Blob Protocol which provides
a method for protecting user-defined data across system power
cycles. SEC block protects data in a data structure called a Blob,
which provides both confidentiality and integrity protection.
Encapsulating data as a blob
Each time that the Blob Protocol is used to protect data, a
different randomly generated key is used to encrypt the data.
This random key is itself encrypted using a key which is derived
from SoC's non volatile secret key and a 16 bit Key identifier.
The resulting encrypted key along with encrypted data is called a blob.
The non volatile secure key is available for use only during secure boot.
During decapsulation, the reverse process is performed to get back
the original data.
Commands added
--------------
blob enc - encapsulating data as a cryptgraphic blob
blob dec - decapsulating cryptgraphic blob to get the data
Commands Syntax
---------------
blob enc src dst len km
Encapsulate and create blob of data $len bytes long
at address $src and store the result at address $dst.
$km is the 16 byte key modifier is also required for
generation/use as key for cryptographic operation. Key
modifier should be 16 byte long.
blob dec src dst len km
Decapsulate the blob of data at address $src and
store result of $len byte at addr $dst.
$km is the 16 byte key modifier is also required for
generation/use as key for cryptographic operation. Key
modifier should be 16 byte long.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Hardware accelerated support for SHA-1 and SHA-256 has been added.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable CAAM in platforms supporting the hardware block.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SHA-256 and SHA-1 accelerated using SEC hardware in Freescale SoC's
The driver for SEC (CAAM) IP is based on linux drivers/crypto/caam.
The platforms needto add the MACRO CONFIG_FSL_CAAM inorder to
enable initialization of this hardware IP.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SEC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of SEC IP.
So update acessor functions with common SEC acessor functions to take care
both type of endianness.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale SEC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the CCSR defintion of
SEC to common include
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
U-boot binary size has been increased from 512KB to 768KB.
So update CONFIG_RESET_VECTOR_ADDRESS to reflect the same for
P1010 SPI Flash Secure boot target.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
[York Sun: Modified subject to P1010RDB]
Reviewed-by: York Sun <yorksun@freescale.com>
Add a block to avoid a build error with the variable declaration.
Enable the option on sandbox to prevent an error being introduced in
future.
Signed-off-by: Simon Glass <sjg@chromium.org>
The SoCDK uses EMAC1, not EMAC0. This patch fixes the issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Commit 832472 "tools: socfpga: Add socfpga preloader signing
to mkimage" added tools/socfpga.c which relies on htole32,
le32toh and friends. While compiler.h includes these protypes
for linux from endian.h, it doesn't do so for FreeBSD. Hence
include <sys/endian.h> for FreeBSD.
Cc: Marek Vasut <marex@denx.de>
CC: Tom Rini <trini@ti.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
remove the seldomly used EXT2 support because the U-Boot binary will
not fit into the 512KiB flash otherwise.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
fix broken SPI access by adding/activating BOARD_EARLY_INIT_F
functionality and calling spi_init_f() from there.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
A number of network related files were imported from the LiMon
project; these contain a somewhat unclear license statement:
Copyright 1994 - 2000 Neil Russell.
(See License)
I analyzed the source code of LiMon v1.4.2 which was used for this
import. It does not contain any "License" file, but the top level
directory contains a file "COPYING", which turns out to be GPL v2
of June 1991. So it is legitimate to conclude that the LiMon derived
files are also to be released under GPLv2. Mark them as such.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This board has been orphaned for more than 6 months.
It is the last board defining CONFIG_APM821XX.
The code inside #ifdef CONFIG_APM821XX should be removed too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
On OMAP platforms, SATA controller provides the SCSI subsystem
so implement scsi_init().
Get rid of the unnecessary sata_init() call from dra7xx-evm
and omap5-uevm board files.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Commit 12cc543767 'omap3: overo: Select
fdtfile for expansion board' wrongly missed the operator in the fdtfile
test. Update the test to only overwrite an empty fdtfile environment
variable.
Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
SCIF of koelsch use external clock mode.
This enables external clock mode on koelsch board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
SCIF of lager use external clock mode.
This enables external clock mode on lager board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The clock of SCIF (serial port) of lager is supplied from External
Clock. And value of clock is 14.7456MHz.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Enable this feature to support driver model before relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Change this board to add a device tree.
This also adds a pinmux header file although it is not used as yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Most of the smdkv310 features are common with other exynos4 boards. To
permit easier addition of driver model support, use the common file and
add a device tree file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Most of the arndale features are common with other exynos5250 boards. To
permit easier addition of driver model support, use the common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
These boards do not in fact have a Chrome OS EC, nor a TPS565090 PMIC, so
move the settings into a separate common file to be used by those that need
it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
A few things are common but are not in the common file. Fix this and
rename the file to fit with the other exynos*-common files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since exynos4 and exyno5 share many settings, we should move these into
a common file to avoid duplication.
In effect the changes are that all exynos boards now have EXT4 and FAT
write support. This affects exynos5250 and exynos5420 which previously
did not. This also disables the ext2 commands which are equivalent to
ext4 anyway.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We want exynos5250-dt.h to be a board which can support any exynos5250
device. This matches the naming used by Linux. As a first step, rename
the existing -dt files to -common to make it clear they are common files,
and not specific boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
With the driver model conversion we are going to be using driver model for
SPI and not for I2C. This works OK so long as a board doesn't need both
dm and non-dm versions of the cros_ec driver. Since pit uses SPI and snow
uses I2C we need to split the configs so that only one driver is compiled
for each platform.
We can fix this later when driver model supports I2C.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Exynos 5250 boards (snow, spring) use the I2C driver but Exynos 5420 boards
cannot due to a hardware design decision. Select the correct driver to use
in each case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Things run faster when the data cache is enabled, so turn it on along with
the 'dcache' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Support reading/writing ext4 partitions.
Signed-off-by: Kevin Mihelich <kevin@archlinuxarm.org>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Enable 'fastboot' command.
This is currently enabled but not yet functional. Including it in the
configuration will ease further testing and development as discussed
on the mailing list.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Some users (QNX and Windows CE users in particular) have asked
to disable the Penguin shown on the display at boot time.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Increase the maximum number of arguments allowed by the Hush parser.
This prevents errors when users or scripts aren't quoting parameters
when setting the "bootargs" variable et al.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Enable the "i2c edid" command to query data from an attached
HDMI monitor.
Usage is typically this:
U-Boot > i2c dev 1
U-Boot > i2c edid 0x50
...
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
If no boot script was found, expose internal storage over the
USB mass storage gadget to allow easy programming.
This is especially useful when SD cards are inaccessible or when
loading SATA drives.
More details are available in this blog post:
http://boundarydevices.com/u-boot-usb-mass-storage-gadget/
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Remove the individual attempts to load using ext2 and fat, replace with the
generic load command supporting available filesystem types.
Signed-off-by: Kevin Mihelich <kevin@archlinuxarm.org>
This patch enables boot to USB storage devices by expanding on the list
of boot devices.
Because the USB startup currently takes a long time, it places USB at
the end of the list of supported devices.
You can over-ride the boot order using the bootdevs environment variable.
For instance, this will make USB the first (highest priority) device:
U-Boot > setenv bootdevs usb mmc sata
U-Boot > saveenv
Signed-off-by: Diego Rondini <diego.rondini@kynetics.it>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Add support for the USB mass storage to enable access to on-board
storage (especially eMMC and SATA).
Details at:
http://boundarydevices.com/u-boot-usb-mass-storage-gadget/
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Enable and use the CONFIG_CMD_FS_GENERIC to avoid hard-coding the
filesystem type into the environment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Split the SoCFPGA configuration into SoC-specific part which is
common for all boards (socfpga_cyclone5_common.h) and a board
specific part. There is currently only one board, which is the
generic SoCFPGA board (socfpga_cyclone5.h), but there are more
to come.
This is necessary due to various features of the boards, which
unfortunatelly cannot be autodetected.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Reorganize and cleanup the configuration file for SoCFPGA. There
is no functional change after this cleanup. This was necessary,
since the file was a wild mess and it was impossible to make sense
of it's content, let alone change something without breaking some
other thing. This patch puts the contents on par with regular U-Boot
standards.
Also remove unused preprocessor symbols CONFIG_SINGLE_BOOTOADER
and CONFIG_USE_IRQ, which is undefined by default. Finally, do
logical reordering of the defines in the file so it's much more
readable. The reordering was also necessary for the splitting
as the initial one was messy.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Enable the SDMMC boot as default boot for SOCFPGA U-Boot dev kit.
Enable the bootz command as zImage is used instead uImage.
Signed-off-by: Chin Liang See <clsee@altera.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Enable the DesignWare MMC controller driver support
for SOCFPGA Cyclone5 dev kit
Signed-off-by: Chin Liang See <clsee@altera.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Enable the PL310 L2 cache controller support for the SoCFPGA.
With the cache related issues resolved, this is safe to be done.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
The code is now fixed to the point where we can safely enable
the L1 data cache. Enable the D-Cache and set it as write-alloc.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
The Cortex-A9 has 32-byte long L1 cachelines. Define this value.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Add code necessary to program the FPGA part of SoCFPGA from U-Boot
with an RBF blob. This patch also integrates the code into the
FPGA driver framework in U-Boot so it can be used via the 'fpga'
command.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
V2: Move the not-CPU specific stuff into drivers/fpga/ and base
this on the cleaned up altera FPGA support.
The timer reload value is a property of the timer hardware and there
is no reason for this to be configurable. Place this into the timer
driver just like on the other hardware.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Add the entire bulk of code to read out clock configuration from the SoCFPGA
CPU registers. This is important for MMC, QSPI and UART drivers as otherwise
they cannot determine the frequency of their upstream clock.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
V2: Fixed the L4 MP clock divider and synced the clock code with latest
rocketboards codebase (thanks Dinh for pointing this out)
Like many platforms, the Altera socfpga platform requires that the
preloader be "signed" in a certain way or the built-in boot ROM will
not boot the code.
This change automatically creates an appropriately signed preloader
from an SPL image.
The signed image includes a CRC which must, of course, be generated
with a CRC generator that the SoCFPGA boot ROM agrees with otherwise
the boot ROM will reject the image.
Unfortunately the CRC used in this boot ROM is not the same as the
Adler CRC in lib/crc32.c. Indeed the Adler code is not technically a
CRC but is more correctly described as a checksum.
Thus, the appropriate CRC generator is added to lib/ as crc32_alt.c.
Signed-off-by: Charles Manning <cdhmanning@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
V2: - Zap unused constant
- Explicitly print an error message in case of error
- Rework the hdr_checksum() function to take the *header directly
instead of a plan buffer pointer
Remove this symbol from configs, since it's unused.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Chin Liang See <clsee@altera.com>
The DMA descriptors used by the DW MMC block must be aligned to cacheline
size, otherwise we are unable to properly flush/inval cache over them and
we get data corruption.
The reason I chose this approach of expanding the structure is because
the driver allocates the descriptors in bulk. This approach does waste
space by inserting slop inbetween the descriptors, but it makes access
to the descriptors easy as the compiler does know the real size of the
structure. It also makes cache operations easy, since the size of the
structure is cache aligned and the structure start address is as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Pavel Machek <pavel@denx.de>
Get rid of the line-over-80 problems and zap the typedef that
went alongside those enums.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
This patch adds support for the OT1200 series of devices.
Following components are used in u-boot:
+ ethernet
+ i2c
+ emmc
+ gpio
For more details see README.
Changes v1 > v2
- make use of enable_cspi_clock(..)
- fix usage of OUTPUT_40OHM define
- added README
Changes v2 > v3
- improve spelling in README
- added own copy of mx6q_4x_mt41j128.cfg
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
PERST_GPIO and POWER_GPIO are currently swapped.
Fix the GPIO assignments as per the board schematics.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Besides converting the LS-XHL and LS-CHLv2 to generic board, fix a typo
which accidentally reverted the bootsource to 'hdd' although the default
bootsource should be 'legacy'.
Cc: Tom Rini <trini@ti.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Siemens boards are now using DFU in fullspeed only. For
this CONFIG_USB_GADGET_DUALSPEED is undefined.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Liu Bin <b-liu@ti.com>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Use the new force parameter to make the stdio_deregister succeed, replacing
stdin with a nulldev, and assume that the usb keyboard will come back after
the reset.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
In some cases we really want to move forward with a deregister, add a force
parameter to allow this, and replace the dev with a nulldev in this case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch add MTDIDS and MTDPARTS defaults settings to sheevaplug
Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Changes in v1:
- add MTDIDS and MTDPARTS default to sheevaplug
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
This patch move the environment offset in sheevaplug.
The size of the u-boot binary is become too big.
Fix saving environments was result of corrupting the u-boot.
Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Changes in v2:
- patch description
Changes in v1:
- fix sheevaplug environment offset
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Update the ddr scripts for LPDDR2 and add two build configs for LPDDR2
arm2 board. Since the LPDDR2 arm2 board has different DDR size, use
CONFIG_DDR_MB in defconfig to replace the PHYS_SDRAM_SIZE.
Signed-off-by: Ye.Li <B37916@freescale.com>
This patch adds the i.MX6DL arm2 board support. The i.MX6DL ARM2
shared the same board with i.MX6Q ARM2 board since the i.MX6DL is
pin-pin compatible with i.MX6Q.
The patch also support the DDR 32-BIT mode option. Please define
CONFIG_DDR_32BIT in the board configure file to enable DDR 32-BIT
mode.But due to the board design, it's 64bit DDR buswidth physically,
so, if you CONFIG_DDR_32BIT, the DDR memory size will be half of it.
Signed-off-by: Ye.Li <B37916@freescale.com>
Enable the CONFIG_CMD_FS_GENERIC on m53evk to avoid per-fs specific commands
and tweak the environment to cater for this new option.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Enable the CONFIG_CMD_FS_GENERIC on m28evk to avoid per-fs specific commands
and tweak the environment to cater for this new option.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Make sure the boot.scr exists on the card before loading it
from the card to avoid annoying message on the console.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Make sure the boot.scr exists on the card before loading it
from the card to avoid annoying message on the console.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
1. Set the image load partition to the first FAT partition.
2. Set the kernel rootfs partition to the second partition.
Signed-off-by: Ye.Li <B37916@freescale.com>
To support loading FDT file for kernel, add the fdt address,
file and loading script to arm2 board default environment.
Signed-off-by: Ye.Li <B37916@freescale.com>
Some of the #defines in spi.h are not bracketed. To avoid future mistakes
add brackets. Also add an explanatory comment for SPI_CONN_DUAL_...
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Sandbox may as well support everything. This increases the amount of code
that is built/tested by sandbox, and also provides access to all the
supported SPI flash devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
LS1021AQDS has a variant with DDR4 slot. This patch adds a new defconfig
for this variant to enable DDR4 support. RAW timing parameters are not
added for DDR4. The board timing parameters are only tuned for single-
rank 1600 and 1800MT/s with Micron DIMM 9ASF51272AZ-2G1A1 due to DIMM
availability.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
Spin table is at the very beginning of boot code. Each core has an individual
release address within the spin table, the ft_cpu_setup fn updates the
"cpu-release-addr" property of each cpu node with the corresponding release
address.
Also fix CPU_RELEASE_ADDR to point to secondary_boot_func.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
of_bus_default_count_cells can be used to get the #address-cells
and #size-cells defined by the current node's parent node. This
is required when using of_read_number to read from FDT nodes that
can be 32 or 64 bytes depending on values defined by the parent.
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
This is being done so that it can be used outside 'fdt_support.c'. Making
life more convenient when reading device node properties that can be 32
or 64 bits long.
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
The driver was written using old DDR3 spec which only covers low speeds.
The value would be suboptimal for higher speeds. Fix both timing according
to latest DDR3 spec, remove tCKE as an config option.
Signed-off-by: York Sun <yorksun@freescale.com>
DP-DDR is used for DPAA, separated from main memory pool for general
use. It has 32-bit bus width and use a standard DDR4 DIMM (64-bit).
Signed-off-by: York Sun <yorksun@freescale.com>
U-boot has been initializing DDR for the main memory. The presumption
is the memory stays as a big continuous block, either linear or
interleaved. This change is to support putting some DDR controllers
to separated space without counting into main memory. The standalone
memory controller could use different number of DIMM slots.
Signed-off-by: York Sun <yorksun@freescale.com>
Add support of NOR and NAND flash for simulator target.
Here
IFC - CS0: NOR flash
IFC - CS1: NAND flash
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This option specifies the default Device Tree used for the run-time
configuration of U-Boot.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Michal Simek <michal.simek@xilinx.com>
This commit moves:
CONFIG_OF_CONTROL
CONFIG_OF_SEPARATE
CONFIG_OF_EMBED
CONFIG_OF_HOSTFILE
Because these options are currently not supported for SPL,
the "Device Tree Control" menu does not appear in the SPL
configuration.
Note:
zynq-common.h should be adjusted so as not to change the
default value of CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
The libc headers on FreeBSD and likely related projects as well contain an
header file, cdefs.h which provides similiar functionality as linux/compiler.h.
It provides compiler independent defines like __weak __packed, to allow
compiling with multiple compilers which might have a different syntax for such
extension.
Since that header file is included in multiple standard headers, like stddef.h
and stdarg.h, multiple definitions of those defines will be present if both are
included. When compiling u-boot the compiler will warn about it hundreds of
times since e.g. common.h will include both files indirectly.
commit 7ea50d5284 "compiler_gcc: do not redefine
__gnu_attributes" prevented such redefinitions, but this was undone by commit
fb8ffd7cfc "compiler*.h: sync
include/linux/compiler*.h with Linux 3.16".
Add the checks back where necessary to prevent such warnings.
As the original patch this checkpatch warning is ignored:
"WARNING: Adding new packed members is to be done with care"
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Since clang has a different definition for uninitialized_var
it will complain that it is redefined in include/compiler.h.
Since these are already defined in linux/compiler.h just remove
this instance.
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
The section name and the C variable name seem to be opposite.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Now config_cmd_defaults.h is empty so it can be deleted safely.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since CONFIG_CMD_IMPORTENV is defined in config_cmd_defaults.h,
it should be enabled for all the boards except bf506f-ezkit
that undefs it explicitely.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Since CONFIG_CMD_GO is defined in config_cmd_defaults.h
(and no board undefs it its own header), it can be moved to
Kconfig with the default value "y".
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Since CONFIG_CMD_EXPORTENV is defined in config_cmd_defaults.h,
it should be enabled for all the boards except bf506f-ezkit
that undefs it explicitely.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Since CONFIG_CMD_CRC32 is defined in config_cmd_defaults.h,
it is enabled for all the boards except the ones undefining it
explicitly:
kwb
tseries_mmc
tseries_nand
tseries_spi
vct_platinum_onenand_small
vct_platinum_small
vct_platinumavc_onenand_small
vct_platinumavc_small
vct_premium_onenand_small
vct_premium_small
The default value of this config option should be "y" and
"# CONFIG_CMD_CRC32 is not set" should be added for those exceptions.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
CONFIG_CMD_BOOTM is defined in config_cmd_defaults.h
which is forcebly included from each board.
So, the default value of "config CMD_BOOTM" should be "y".
For some boards undefining it (bf506f-ezkit, controlcenterd_TRAILBLA,
controlcenterd_TRAILBLAZER_DEVELOP, controlcenterd_TRAILBLAZER),
"# CONFIG_CMD_BOOTM is not set" should be added to their defconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
If this option is enabled, the objects under lib/ directory
are compiled with speed optimization, not size optimization.
(Currently, only used by some Blackfin boards.)
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Scsi disks need to be probed before we try to access them, otherwise all
accesses fail with: ** Bad device size - scsi 0 **.
Reported-by: Karsten Merker <merker@debian.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Karsten Merker <merker@debian.org>
One of the I2C EEPROM is used to store/save and edit mac
addresses of ports.
this patch add required CONFIG to support the same
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
CPC1 is not being enabled by default as powerpc is supposed to
use only CPC2. Though by editing hwconfig en_cpc option,
CPC1 can also be enabled.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1042RDB is a Freescale reference board that hosts the T1042 SoC
(and variants). The board is similar to T1040RDB, T1042 is a reduced
personality of T1040 SoC without Integrated 8-port Gigabit(L2 Switch).
T1042RDB is configured with serdes protocol 0x86 which can support
following interfaces
- 2 RGMII's on DTSEC4, DTSEC5
- 1 SGMII on DTSEC3
DTSEC1, DTSEC2 are not connected on board.
This Patch
- add T1042RDB support
- updates README file for T1042RDB details and update commands for switching
to alternate banks from vBank0 to vBank4 and vice versa
This patch also does minor clean ups for fdt defines for T1042RDB and
T1042RDB_PI board
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds support of rcw for T1042RDB, it makes following changes :
- Adds t1042_rcw.cfg file for serdes protocol 0x86 for T1042RDB
- Renames t1042_pi_rcw.cfg file from t1042_rcw.cfg and also updates
comments for valid serdes protocol which is 0x06
- Also updates CONFIG_SYS_FSL_PBL_RCW for T1042RDB
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable the Extend address to support SPI flash more than 16MB.
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Currently, CONFIG_SPL_SPI_* #defines are used for controlling SPI boot in
SPL. These #defines do not allow the user to select SPI mode for the SPI flash
(there's no CONFIG_SPL_SPI_MODE, so the SPI mode is hardcoded in
spi_spl_load.c), and duplicate information already provided by
CONFIG_SF_DEFAULT_* #defines.
Kill CONFIG_SPL_SPI_*, and use CONFIG_SF_DEFAULT_* instead.
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Hannes Petermaier <hannes.petermaier@br-automation.com>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
MXC SPI driver has a feature whereas a GPIO line can be used to force CS high
across multiple transactions. This is set up by embedding the GPIO information
in the CS value:
cs = (cs | gpio << 8)
This merge of cs and gpio data into one value breaks the sf probe command:
if the use of gpio is required, invoking "sf probe <cs>" will not work, because
the CS argument doesn't have the GPIO information in it. Instead, the user must
use "sf probe <cs | gpio << 8>". For example, if bank 2 gpio 30 is used to force
cs high on cs 0, bus 0, then instead of typing "sf probe 0" the user now must
type "sf probe 15872".
This is inconsistent with the description of the sf probe command, and forces
the user to be aware of implementaiton details.
Fix this by introducing a new board function: board_spi_cs_gpio(), which will
accept a naked CS value, and provide the driver with the relevant GPIO, if one
is necessary.
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Eric Benard <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Let's enable CONFIG_SYS_GENERIC_BOARD in order to get rid of warnings related
to generic board support is not in place.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Sabrelite board has two solts: 0 is SD3 (bottom) slot and 1 is uSD4 (top) slot.
This patch makes use of both slots instead of only one.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
Let's enable CONFIG_SYS_GENERIC_BOARD in order to get rid of warnings related
to generic board not being supported.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We should not hardcode CONFIG_NETMASK in the config file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
This patch uses generic 'load' command instead of 'fatload' for 'loadbootscript' and 'loadbootenv' as already done for 'loadimage' and 'loaduimage' for OMAP4 boards.
This allows to use EXT partition instead of FAT, while keeping FAT compatibility.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@ti.com>
Copy them from Linux v3.16 tag.
My main motivation of this commit is to add compiler-clang.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
U-Boot has imported various source files from other projects,
mostly Linux.
Something like
#ifdef __UBOOT__
[ modification for U-Boot ]
#else
[ original code ]
#endif
is an often used strategy for clarification of adjusted parts,
that is, easier re-sync in future.
Instead of defining __UBOOT__ in each source file,
passing it from the top Makefile would be easier.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Define CONFIG_SYS_FSL_ESDHC_ADDR using USDHC4_BASE_ADDR.
USDHC3 and USDHC4 are both initialized in board_mmc_init. There is
no restriction on USDHC3 addr or USDHC4 addr should be assigned to
CONFIG_SYS_FSL_ESDHC_ADDR. So, just choose USDHC4_BASE_ADDR to avoid
errors when fsl_esdhc_mmc_init is invoked.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Define CONFIG_SYS_FSL_ESDHC_ADDR using USDHC4_BASE_ADDR which is used
in board_mmc_init.
If board_mmc_init failed, cpu_mmc_init->fsl_esdhc_mmc_init will use
CONFIG_SYS_FSL_ESDHC_ADDR to initialize sdhc. So set this macro to
correct value.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
This adds NAND support for the Vybrid tower system (TWR-VF65GS10)
provided by the vf610_nfc driver. Full 16-Bit bus width is
supported. Also an aditional config vf610twr_nand is introduced
which gets the environment from NAND. However, booting U-Boot from
NAND is not yet possible due to missing boot configuration block
(BCB).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Use driver model for serial ports.
Since Tegra now uses driver model for serial, adjust the definition of
V_NS16550_CLK so that it is clear that this is only used for SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some Tegra device tree files do not include information about the serial
ports. Add this and also add information about the input clock speed.
The console alias needs to be set up to indicate which port is used for
the console.
Also add a binding file since this is missing.
Series-changes; 5
- Add full serial port nodes from Linux tree (commit fc9d4dbe)
- Use /chosen/stdout-path instead of /aliases/console to specify the console
Signed-off-by: Simon Glass <sjg@chromium.org>
Add driver model support so that ns16550 can support operation both with
and without driver model.
The driver needs a clock frequency so cannot stand alone unfortunately. The
clock frequency must be provided by a separate driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust the sandbox serial driver to use the new driver model uclass. The
driver works much as before, but within the new framework.
Signed-off-by: Simon Glass <sjg@chromium.org>
Serial devices support simple byte input/output and a few operations to find
out whether data is available. Add a basic uclass for serial devices to be
used by drivers that are converted to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Within /chosen we may have a node which points to another node, similar
to how /aliases works. Add a helper function to do this lookup.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is an implementation of GPIOs for Tegra that uses driver model. It has
been tested on trimslice and also using the new iotrace feature.
The implementation uses a top-level GPIO device (which has no actual GPIOS).
Under this all the banks are created as separate GPIO devices.
The GPIOs are named as per the Tegra datasheet/header files: A0..A7, B0..B7,
..., Z0..Z7, AA0..AA7, etc.
Since driver model is not yet available before relocation, or in SPL, a
special function is provided for seaboard's SPL code.
Signed-off-by: Simon Glass <sjg@chromium.org>
For some boards board_init() will change GPIOs, so we need to have driver
model available before then. Adjust the board init to arrange this, but
enable it for driver model only, just to be safe.
This does create additional #ifdef logic, but it is safer than trying to
make a pervasive change which may cause some boards to break.
Signed-off-by: Simon Glass <sjg@chromium.org>
