This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
The CONFIG_PHY_MARVELL has already been migrated to Kconfig (some boards
already had it in their Kconfig), but had not been moved for older
boards.
Move it to the defconfigs for all boards.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This converts the following to Kconfig:
CONFIG_SPI
This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver. For now, just update
the CONFIG tests. This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
A number of platforms include config_distro_defaults.h but do not enable
CONFIG_DISTRO_DEFAULTS. As they plainly intended to, set that flag and
re-sync config files.
Signed-off-by: Tom Rini <trini@konsulko.com>
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <trini@konsulko.com>
We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.
Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic
Signed-off-by: Tom Rini <trini@konsulko.com>
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:
../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {
Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
CONFIG_FIT_EMBED might be confused with CONFIG_OF_EMBED, rename it
MULTI_DTB_FIT as it is able to get a DTB from a FIT image containing
multiple DTBs. Also move the option to the Kconfig dedicated to the DTS
options and create a README for this feature.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE
In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.
In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.
There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with
./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC
And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable various config options to allow U-boot at runtime to select the
proper dtb to use from the list of dtb's within the FIT image.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Standardise U-Boot prompt on all keystone2 platforms
instead of platform specific prompt.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch makes SYS_TEXT_BASE a config option for Keystone2
so that it can be used to load u-boot at different addresses
on secure and non-secure Keystone2 devices.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
As reported in [1], rename the k2* dts files to keystone-* files
this will force consistency throughout.
Script for the same (and hand modified for Makefile and config
files):
for i in arch/arm/dts/k2*
do
b=`basename $i`;
git mv $i arch/arm/dts/keystone-$b;
sed -i -e "s/$b/keystone-$b/g" arch/arm/dts/*[si]
done
This is similar to linux kernel commit 5edafc29829bc ("ARM: dts: k2*: Rename
the k2* files to keystone-k2* files")
[1] http://marc.info/?l=linux-arm-kernel&m=145637407804754&w=2
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly
update all of the config files we must also update CMD_PART and CMD_GPT to also
be in Kconfig in order to avoid complex logic elsewhere to update all of the
config files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit 7a777f6d6f ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c798799f ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.
We generally do not like such partial moves. This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.
I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.
This commit was created as follows:
[1] Edit Kconfig (remove the "depends on", add the "default",
copy the prompt and help message from Linux)
[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_INFO_QUIET
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default n, re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
move the UBI config options into Kconfig.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Reviewed by: Evgeni Dobrev <evgeni at studio-punkt.com>
In some cases we were missing CONFIG_USB=y so enable that when needed.
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
There is only one ethernet mac address in e-fuse, but there are
multiple slaves in keystone net, so enable random mac address
support.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable SPI and SPI Flash driver model as K2HK SPI controller driver
supports driver model.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Create an entry for "config USB_XHCI_DWC3" in Kconfig and
switch over to it for all boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move CONFIG_USB_XHCI to defconfig files for all boards, renaming it
into CONFIG_USB_XHCI_HCD.
As commented in the help of "config USB_XHCI" entry, this has been
a TODO for a long time; now CONFIG_USB_XHCI_HCD and CONFIG_USB_XHCI
have been unified in favor of the former.
Note:
Some boards define CONFIG_USB_XHCI in their headers without
CONFIG_USB, which does not meet the "depends on" in Kconfig.
I added CONFIG_USB=y for those boards when converting.
Otherwise, they would fail to build.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
