Define enum PMUX_FUNC_DEFAULT, which indicates that a table entry passed
to pinmux_config_pingrp()/pinmux_config_pingrp_table() shouldn't change
the mux option in HW.
For pins that will be used as GPIOs, the mux option is irrelevant, so we
simply don't want to define any mux option in the pinmux initialization
table.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The register writes performed by arch/arm/cpu/arm720t/tegra30/cpu.c
enable_cpu_power_rail() set the voltage to 1.0V not 1.4V as the comment
implies. Fix the comment.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
If CONFIG_API is ever to be enabled on Tegra, this define must be set,
since api/api_storage.c uses it.
A couple of annoyting things about CONFIG_SYS_MMC_MAX_DEVICE
1) It isn't documented in README. The same is true for a lot of similar
defines used by api_storage.c.
2) It doesn't represent MAX_DEVICE but rather NUM_DEVICES, since the
valid values are 0..n-1 not 0..n.
However, I this patch does not address those shortcomings.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
"make ep8248_config" fails with an error like this:
$ make ep8248_config
make: *** [ep8248_config] Error 1
Its cause is that there are two entries for "ep8248".
The first is around line 652 of boards.cfg. (as Active)
The second appears around line 1230. (as Orphan)
This bug was accidentally introduced by commit e7e90901.
But it is not the author's fault. He just intended to change
IDS8247 board.
The commiter added ep8248 entry by mistake when he resolved a conflict.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Kim Phillips <kim.phillips@linaro.org>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
This patch converts the following boards to use generic board: MPC8536DS,
MPC8572DS, MPC8641HPCN, p1_p2_rdb_pc, corenet_ds, t4qds, B4860QDS. It has
been tested on NOR boot on MPC8536DS, MPC8572DS, P1021RDB, P4080DS,
P5020DS, P5040DS, P3041DS, T4240QDS, B4860QDS.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Ying Zhang <b40530@freescale.com>
CC: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Haijun.Zhang <Haijun.Zhang@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Shaohui Xie <Shaohui.Xie@freescale.com>
The argument boot_flag of board_inti_f() hasn't been used for powerpc until
recent changing to use generic board. Set it to 0 as a proper value.
Signed-off-by: York Sun <yorksun@freescale.com>
baord_init_f takes one argument, boot_flag. It has not been used for
powerpc, until recently changing to use generic board architecture.
The boot flag is added as a return value from cpu_init_f().
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alexander Graf <agraf@suse.de>
The return value has not been checked by its caller, until recent change
of using generic board architecture. The error of this function is not
critical enough to hang the system. Printing the warning message is enough
to catch user's attention. U-boot should continue to boot to give user
a chance to fix the EEPROM. Chaning the return value to 0 to avoid hanging
in the board_init_r().
Signed-off-by: York Sun <yorksun@freescale.com>
The pointer of device tree comes from r3 for QEMU. This is not the case
for normal SoCs out of reset. Having gd->fdt_blob as 0 is important for
other functions to detect the non-existence of device tree.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alexander Graf <agraf@suse.de>
U-boot image has grown and exceeded the predefined 512KB. Increasing to
768KB to align with other powerpc boards. Tested on MPC8572DS for 32-
and 36-bit targets with NOR flash boot. NAND boot is not covered by
this patch.
Also update board maintainer for these boards.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
when qe-ucode fails to be uploaded, "deep sleep" will hang.
if there is no qe-ucode, disable qe module for platforms
which support "deep sleep"
Signed-off-by: Zhao Qiang <B45475@freescale.com>
We want to use the TLB mapping helpers in relocated mode as well. These helpers
need to have awareness of already occupied TLB entries. We already had them in
sync in non-relocated mode, but need to resync them when we move into relocated.
Signed-off-by: Alexander Graf <agraf@suse.de>
For the QEMU machine type, we can plug in either e500v2, e500mc, e5500
or e6500 style cores into the system. U-boot has to work with all of them.
So avoid using HID1 which is not available on e500mc systems to make sure
we don't trap on it.
Signed-off-by: Alexander Graf <agraf@suse.de>
We only need u-boot to bother about a single core in the QEMU machine.
Everything that would require additional knowledge of more cores gets
handled by QEMU and passed straight into the payload we execute.
Because of this setup, it would be counterproductive to enable SMP support
in u-boot. We would have to rip CPUs out of already existing spin tables
and respin them from u-boot. It would be a pretty big mess.
So only assume we have a single core. This fixes errors about CONFIG_MP
being disabled.
Signed-off-by: Alexander Graf <agraf@suse.de>
This should prevent the problems that the CCF can deadlock with certain
traffic patterns.
This also fixes the workaround for A-006559 that was not correctly
implemented before.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Fix the IRQ/GPIO settings: all the muxed GPIO/external IRQs that are
used as internal interrupts are defined as GPIOs to avoid confusion
between the internal/external interrupts.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This adds the reset support for the following devices that was until
then not implemented:
- BFTIC4
- QSFPs
This also fixes the configuration of the prst behaviour for the other
resets: Only the u-boot and kernel relevant subsystems are taken out of
reset (pcie, ZL30158, and front eth phy).
Most of the prst config move to misc_init_f(), except for the PCIe
related ones that are in pci_init_board and the bftic and ZL30158 ones
that should be done as soon as possible.
Only the behavior of the Hooper reset is changed according to the
documentation as the application is not able to not configure the switch
when it is not reset.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This prevents u-boot from accessing into the reserved memory areas that
we have for /var and the logbooks.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch defines the post_hotkeys_pressed() function that is used for:
- triggering POST memory regions test
- starting the test application through the checktestboot command in
a script by setting the active bank to testbank
The post_hotkeys_pressed return the state of the SELFTEST pin.
The patch moves from the complete POST-memory test that is too long in
its SLOW version for our production HW test procedure to the much shorter
POST-memory-regions test.
Finally, the unused #defines for the not so relevant mtest command are
removed.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Add readout of dip-switch to revert to factory settings.
If one or more dip-switch are set, launch bank 0 that contains the
bootloader to do the required action.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
The unit LEDs are managed by the QRIO CPLD. This patch adds support for
accessing these LEDs in the QRIO.
The LEDs then are set to a correct boot state:
- UNIT-LED is red
- BOOT-LED is on.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
The T4080 SoC is a low-power version of the T4160.
T4080 combines 4 dual-threaded Power Architecture e6500
cores with single cluster and two memory complexes.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Current driver uses a Maximum value for MDIO_HOLD when doing 10G MDIO
access, this is due to an errata A-006260 on T4 rev1.0 which is fixed
on rev2.0, so remove the maximum value to use the default value for rev2.0.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Secure Boot Target is added for T2080RDB
Changes:
For Secure boot, CPC is configured as SRAM and used as house
keeping area which needs to be disabled.
So CONFIG_SYS_CPC_REINIT_F is defined for CONFIG_T2080RDB.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
T1040RDB.h file is removed and a unified file T104xRDB.h is created.
Hence macro CONFIG_T1040 is renamed to CONFIG_T104x.
Signed-off-by: Gaurav Kumar Rana <gaurav.rana@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
T4240RDB board Specification
----------------------------
Memory subsystem:
6GB DDR3
128MB NOR flash
2GB NAND flash
Ethernet:
Eight 1G SGMII ports
Four 10Gbps SFP+ ports
PCIe:
Two PCIe slots
USB:
Two USB2.0 Type A ports
SDHC:
One SD-card port
SATA:
One SATA port
UART:
Dual RJ45 ports
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
B4860QDS has a PowerOne ZM7300 programmable digital Power
Manager which is programmed as per the value read from
the fuses.
Reference for this code is taken from t4qds VID implementation.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Adds Support for PowerOne ZM7300 voltage regulator.
This device is available on some Freescale Boards like B4860QDS
and has to be programmed to adjust the voltage on the board.
The device is accessible via I2C interface.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Use helper function zynq_validate_bitstream so that the
code can be reused easily for different cases of dma transfer.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use zynq_dma_xfer_init, zynq_align_dma_buffer,
zynq_dma_transfer helper function performing dma
transfers so that the code can be reused easily for
different cases of dma transfer.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Warnings:
drivers/fpga/zynqpl.c:150:32: warning: Using plain integer as NULL pointer
drivers/fpga/zynqpl.c:152:16: warning: Using plain integer as NULL pointer
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Connect FPGA version with appropriate operations
to remove huge switch-cases for every FPGA family.
Tested on Zynq. Spartan2/Spartan3/Virtex2 just compile test.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enabling configs for GPIO CMD, EXYNOS4 family and replacing
exynos_gpio_get with new linear GPIO pin number required
because of the new function asking only 2 arguments (pin
and value) instead of 3 (bank, pin and value).
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch includes following changes :
* Adds gpio pin numbering support for EXYNOS SOCs.
To have consistent 0..n-1 GPIO numbering the banks are divided
into different parts where ever they have holes in them.
* Rename GPIO definitions from GPIO_... to S5P_GPIO_...
These changes were done to enable cmd_gpio for EXYNOS and
cmd_gpio has GPIO_INPUT same as s5p_gpio driver and hence
getting a error during compilation.
* Adds support for name to gpio conversion in s5p_gpio to enable
gpio command EXYNOS SoCs. Function has been added to asm/gpio.h
to decode the input gpio name to gpio number.
Example: SMDK5420 # gpio set gpa00
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Because I'm leaving Samsung Electronics, I won't have access to their
developer hardware anymore. Przemyslaw Marczak will take over my
responsibilities.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adding two configs:
* CONFIG_FIT - Enable FIT image support.
* CONFIG_FIT_BEST_MATCH - Enable fetching correct DTB from
FIT image by comparing compatibles.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This sets up the linkage from the phydev back to the ethernet device. This
symptom of not doing this which I noticed was:
<NULL> Waiting for PHY auto negotiation to complete....
rather than:
dwmac.1c50000 Waiting for PHY auto negotiation to complete....
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Run "tools/reformat.py -i -d '-' -s 8 <boards.cfg >boards0.cfg && mv boards0
in order to keep the entries sorted.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When write a file into FAT file system, it will search a match file in
root dir. So the find_directory_entry() will get the first cluster of
root dir content and search the directory item one by one. If the file
is not found, we will call get_fatent_value() to get next cluster of root
dir via lookup the FAT table and continue the search.
The issue is in FAT16/12 system, we cannot get root dir's next clust
from FAT table. The FAT table only be use to find the clust of data
aera in FAT16/12.
In FAT16/12 if the clust is in root dir, the clust number is a negative
number or 0, 1. Since root dir is located in front of the data area.
Data area start clust #2. So the root dir clust number should < 2.
This patch will check above situation before call get_fatenv_value().
If curclust is < 2, include minus number, we just increase one on the
curclust since root dir is in continous cluster.
The patch also add a sanity check for entry in get_fatenv_value().
Signed-off-by: Josh Wu <josh.wu@atmel.com>
