Commit graph

4849 commits

Author SHA1 Message Date
Haijun.Zhang
d47e3d2707 esdhc: Detecting 8 bit width before mmc initialization
The upper 4 data signals of esdhc are shared with spi flash.
So detect if the upper 4 pins are assigned to esdhc before
enable sdhc 8 bit width.

Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-22 08:56:34 -08:00
Haijun.Zhang
f7e27cc5ee esdhc: Workaround for card can't be detected on T4240QDS
Card detection pin is ineffective on T4240QDS Rev1.0.
There are two cards can be connected to board.
1. eMMC card is built-in board, can not be removed. so
   For eMMC card it is always there.
2. Card detecting pin is functional for SDHC card in Rev2.0.

This workaround force sdhc driver scan and initialize the card
regardless of whether the card is inserted or not in case Rev1.0.

Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-22 08:56:15 -08:00
Shengzhou Liu
4399434fef net/fm: revert commit 732dfe090d
This patch reverts patch 'add ft_fixup_xgec to support 3rd and 4th 10GEC'.
When dual-role MAC acts as 10G,it still uses fsl,fman-port-1g-rx/tx as before.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2014-01-21 14:05:52 -08:00
Po Liu
6609916efb powerpc:mpc85xx: Add ifc nand boot support for TPL/SPL
Using the TPL method for nand boot by sram was already
supported. Here add some code for mpc85xx ifc nand boot.

	- For ifc, elbc, esdhc, espi, all need the SPL without
	section .resetvec.
	- Use a clear function name for nand spl boot.
	- Add CONFIG_SPL_DRIVERS_MISC_SUPPORT to compile the fsl_ifc.c
	in spl/Makefile;

Signed-off-by: Po Liu <Po.Liu@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-21 13:42:01 -08:00
York Sun
76356eb57c powerpc/mpc85xx: Revise workaround for DDR-A003
Existing workaround only handles one RDIMM on reference design. In case
of two RDIMMs being used, the workaround requires two separate writes to
DDR_SDRAM_MD_CNTL register.

This patch also restores two debug registers changed by the workaround.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Ben Collins <ben.c@servergy.com>
CC: James Yang <James.Yang@freescale.com>
2014-01-21 13:40:52 -08:00
Shengzhou Liu
1576b558b9 powerpc/t2080qds: some update for t2080qds
- add more serdes protocols support.
- fix some serdes lanes route.
- fix SGMII doesn't work and incorrect mdio display for XFI when serdes 0x6d.
- correct boot location info for SD/SPI boot.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-01-21 13:37:41 -08:00
Tom Rini
55ca99f894 Merge branch 'master' of git://git.denx.de/u-boot-i2c 2014-01-20 07:51:22 -05:00
Jeroen Hofstee
13fbde6e4f nand, gpmc: fix reading after switching ecc
The omap_gpmc allows switching ecc at runtime. Since
the NAND_SUBPAGE_READ flag is only set, it is kept when
switching to hw ecc, which is not correct. This leads to
calling chip->ecc.read_subpage which is not a valid
pointer. Therefore clear the flag when switching ecc so
reading in hw mode works again.

Cc: Scott Wood <scottwood@freescale.com>
Cc: Pekon Gupta <pekon@ti.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-01-17 08:04:32 -05:00
Tom Rini
4913fc23f0 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-01-16 13:50:16 -05:00
Nobuhiro Iwamatsu
22e75d6d60 spi: sh_qspi: Add header file that defines the address of registers
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-01-16 08:07:20 +09:00
Tom Rini
7810480952 Merge branch 'master' of git://git.denx.de/u-boot-net 2014-01-14 14:39:53 -05:00
Fabio Estevam
f66e3ded61 net: phy: atheros: Fix the masks for AR8031/8035
Use the same masks as used in the kernel:
https://git.kernel.org/cgit/linux/kernel/git/stable/linux-stable.git/tree/drivers/net/phy/at803x.c?id=refs/tags/v3.12.6

With such changes Ethernet is functional on hummingboard solo.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Marek Vasut <marex@denx.de>
Patch: 306640
2014-01-14 14:00:41 -06:00
Minkyu Kang
a4d481ed81 mmc: dwmmc: mode change to 0644
Don't know why but, file permission was changed

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-01-14 09:44:21 -05:00
Przemyslaw Marczak
c9b0fa310c fuelgauge: max17042: fix i2c read issue which causes infinity loop.
Issues:
- reading i2c data by passing u16 pointer causes errors in read data.
- max17042 status register fields have not only Power On Reset meaning
  so using proper mask is required.

Changes:
- read i2c data to type u32 instead of u16 - avoids buffer overflow
- compare FG status register using mask not just one bit value
- add checking return value to functions fg read/write
- add model lock and model check count
- add debug msg

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
2014-01-14 09:01:05 -05:00
Tom Rini
10fcda8e25 Merge branch 'master' of git://git.denx.de/u-boot-spi 2014-01-13 13:45:15 -05:00
Tom Rini
d104a0c6a1 Merge branch 'master' of git://git.denx.de/u-boot-video 2014-01-13 08:41:04 -05:00
Inderpal Singh
7da7651251 usb: exynos5: arndale: Add network support
Arndale board has AX88760, which is USB 2.0 Hub & USB 2.0 Ethernet Combo
controller, connected to HSIC Phy of USB host controller via USB3503 hub.

This patch uses board specific board_usb_init function to perform reset
sequence for USB3503 hub and enables the relevant config options for
network to work.

Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
2014-01-13 12:23:28 +01:00
Inderpal Singh
16f9480dfc usb: ehci: exynos: set/reset hsic phys
The controller has 3 ports. The port0 is for USB 2.0 Phy, port1 and port2
are for HSIC phys. The usb 2.0 phy is already being setup. This patch
sets up the hsic phys.

Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
2014-01-13 12:23:28 +01:00
Kuo-Jung Su
dcad280056 usb: gadget: fotg210: EP0 fifo empty indication is non-reliable
The fifo size of ep0 is 64 bytes, and if the packet size grater than
64 bytes, the driver would have to fill up the fifo multiple times,
and before filling up the fifo, the driver should make sure the fifo
is empty by checking fifo empty indication.

However there is a hardware bug that the fifo empty indication is
somehow a bit earlier than fifo reset. So if I don't add an extra
delay here, the data might be corrupted. (i.e., 1 byte missing)

After a couple of tests, it truns out that 1 usec is good enough.

This workaround should be applied to all hardware revisions.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
2014-01-13 12:15:13 +01:00
Kuo-Jung Su
bd5e301d35 usb: gadget: fotg210: add w1c interrupt status support
Since hardware revision 1.11.0, the following interrupt status
registers are now W1C (i.e., write 1 clear):

1. Interrupt Source Group 0 Register (0x144) (EP0 Abort: BIT5)
2. Interrupt Source Group 2 Register (0x14C) (All bits)

And before revision 1.11.0, these registers are all R/W.
Which means software must write a 0 to clear the status.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
2014-01-13 12:15:12 +01:00
Kuo-Jung Su
dccacbe019 i2c: fti2c010: fix compiler warning on paddr[]
This fixes the following compiler warnings:

fti2c010.c: In function 'fti2c010_read':
fti2c010.c:204:8: warning: 'paddr' may be used uninitialized in this function [-Wuninitialized]
fti2c010.c: In function 'fti2c010_write':
fti2c010.c:266:8: warning: 'paddr' may be used uninitialized in this function [-Wuninitialized]

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Heiko Schocher <hs@denx.de>
2014-01-13 08:18:38 +01:00
Alexey Brodkin
32d041e218 drivers/designware_i2c - add suppor of CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
Since we agreed on legacy implementation of "eeprom_{read|write}"
(http://patchwork.ozlabs.org/patch/295825/) I had to fix/make it work
again DesignWare I2C driver for cases when 1 EEPROM IC fake I2C with
anumber of "built-in" ICs with different chip addresses.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Tom Rini <trini@ti.com>
cc: Armando Visconti <armando.visconti@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Vipin KUMAR <vipin.kumar@st.com>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
2014-01-13 08:18:13 +01:00
Darwin Rambo
7cc1b02f8f i2c: Fix i2c speed command
This corrects i2c core to interpret the value returned by
i2c_set_bus_speed as a success indicator rather than the
actual speed that was set. When i2c_set_bus_speed returns
a failure code, the speed is unknown so the adapter speed
is set to zero.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Steve Rae <srae@broadcom.com>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-01-13 08:17:51 +01:00
Nobuhiro Iwamatsu
da1ed0d20e rcar_i2c: Clear status before start master receive
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-01-13 08:16:48 +01:00
Hisashi Nakamura
ad5e14ecdd rcar_i2c: Fix receiving wait condition
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-01-13 08:16:22 +01:00
Liu Ying
d47c961695 video: ipu reg: Correct reserved array size in struct ipu_idmac
The array reserved as a placeholder in the structure ipu_idmac
should contain 44 32bit unsigned integer entries instead of 45
ones, because the placeholder is located bewteen the register
IDMAC_SC_CORD1 and the register IDMAC_CH_BUSY_1 with the address
offsets of 0x804c and 0x8100 respectively.

Reported-by: Robin Gong <b38343@freescale.com>
Acked-by: Robin Gong <b38343@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
2014-01-12 23:00:06 +01:00
Liu Ying
f794b532eb video: ipu reg: Correct reserved1 array size in struct ipu_cm
The array reserved1 as a placeholder in the structure ipu_cm
should contain 4 32bit unsigned integer entries instead of 16
ones, because the placeholder is located bewteen the register
IPU_CH_DB_MODE_SEL_1 and the register IPU_ALT_CH_DB_MODE_SEL_0
with the address offsets of 0x154 and 0x168 respectively.

Reported-by: Robin Gong <b38343@freescale.com>
Acked-by: Robin Gong <b38343@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
2014-01-12 22:59:21 +01:00
Siva Durga Prasad Paladugu
35a55fb57f sf: params: Removed flag SECT_4K for Micron N25Q128
Remove the flag SECT_4K for device N25Q128 as the 4K-byte
sub sector erase granularity is available only for top/bottom
8 sectors in some of the N25Q128 chips.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-12 21:40:23 +05:30
Jagannadha Sutradharudu Teki
b902e07cea sf: Add CONFIG_SF_DUAL_FLASH
This config will use for defining greater than single flash support.
currently - DUAL_STACKED and DUAL_PARALLEL.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-12 21:40:22 +05:30
Jagannadha Sutradharudu Teki
056fbc73d5 sf: Add dual memories support - DUAL_PARALLEL
This patch added support for accessing dual memories in
parallel connection with single chipselect line from controller.

For more info - see doc/SPI/README.dual-flash

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-12 21:40:22 +05:30
Jagannadha Sutradharudu Teki
f77f469117 sf: Add dual memories support - DUAL_STACKED
This patch added support for accessing dual memories in
stacked connection with single chipselect line from controller.

For more info - see doc/SPI/README.dual-flash

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-12 21:40:11 +05:30
Jagannadha Sutradharudu Teki
ab92224f45 sf: ops: Unify read_ops bank configuration
Unified the bar code from read_ops into a spi_flash_bar()

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-12 21:38:33 +05:30
Jagannadha Sutradharudu Teki
2ba863fae6 sf: Code cleanups
- comment typo's
- func args have a proper names

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-12 21:38:21 +05:30
Jagannadha Sutradharudu Teki
9f4322fd22 sf: Divide flash register ops from QEB code
QEB code comprises of couple of flash register read/write operations,
this patch moved flash register operations on to sf_op

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-11 16:51:41 +05:30
Jagannadha Sutradharudu Teki
5bb30f1a40 sf: probe: Enable macronix quad read/write cmds support
Added macronix flash quad read/write commands support and
it's up to the respective controller driver usecase to
configure the respective commands by defining SPI RX/TX
operation modes from include/spi.h on the driver.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-11 16:51:39 +05:30
Jagannadha Sutradharudu Teki
067951223e sf: Add macronix set QEB support
This patch adds set QEB support for macronix flash devices
which are trying to program/read quad operations.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-11 16:51:37 +05:30
Jagannadha Sutradharudu Teki
ff063ed480 sf: Discover read dummy_byte
Discovered the read dummy_byte based on the
configured read command.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-11 16:50:45 +05:30
Jagannadha Sutradharudu Teki
c4ba0d82d3 sf: Add QUAD_IO_FAST read support
This patch adds support QUAD_IO_FAST read command.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-11 15:13:27 +05:30
Jagannadha Sutradharudu Teki
33adfb5f9b sf: Separate the flash params table
Moved the flash params table from sf_probe.c and
placed on to sf_params.c, hence flash params file will
alter based on new addons.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-11 15:13:27 +05:30
Jagannadha Sutradharudu Teki
35ba667df4 sf: probe: Enable RD_FULL and WR_QPP
This patch enabled RD_FULL and WR_QPP for supported flashes
in micron, winbond and spansion.

Remaining parts will be add in future patches.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-11 15:13:26 +05:30
Jagannadha Sutradharudu Teki
d08a1baf61 sf: Set quad enable bit support
This patch provides support to set the quad enable bit on flash.

quad enable bit needs to set before performing any quad IO
operations on respective SPI flashes.

Currently added set  quad enable bit for winbond and spansion flash
devices. stmicro flash doesn't require to set as qeb is volatile.
remaining flash devices support will add in future patches.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-11 15:13:26 +05:30
Jagannadha Sutradharudu Teki
6cba6fdf96 sf: ops: Add configuration register writing support
This patch provides support to program a flash config register.

Configuration register contains the control bits used to configure
the different configurations and security features of a device.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-11 15:13:25 +05:30
Jagannadha Sutradharudu Teki
3163aaa63f sf: Add quad read/write commands support
This patch add quad commands support like
- QUAD_PAGE_PROGRAM => for write program
- QUAD_OUTPUT_FAST ->> for read program

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-11 15:13:11 +05:30
Jagannadha Sutradharudu Teki
4e09cc1e2c sf: Add extended read commands support
Current sf uses FAST_READ command, this patch adds support to
use the different/extended read command.

This implementation will determine the fastest command by taking
the supported commands from the flash and the controller, controller
is always been a priority.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-11 15:10:28 +05:30
Axel Lin
12f00caf61 spi: sh_spi: Use sh_spi_clear_bit() instead of open-coded
We have a sh_spi_clear_bit() function, there's no reason not to use it.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-01-11 12:21:31 +05:30
Kuo-Jung Su
66cb9eb1d6 spi: Add Faraday SPI controller support
The Faraday FTSSP010 is a multi-function controller
which supports I2S/SPI/SSP/AC97/SPDIF. However This
patch implements only the SPI mode.

NOTE:
The DMA and CS/Clock control logic has been altered
since hardware revision 1.19.0. So this patch
would first detects the revision id of the underlying
chip, and then switch to the corresponding software
control routines.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
CC: Tom Rini <trini@ti.com>
2014-01-11 12:21:30 +05:30
Tom Rini
7f673c99c2 Merge branch 'master' of git://git.denx.de/u-boot-arm
Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.

Conflicts:
	include/configs/exynos5250-dt.h

Signed-off-by: Tom Rini <trini@ti.com>
2014-01-10 10:56:00 -05:00
Tom Rini
8401bfa91e Merge branch 'master' of git://git.denx.de/u-boot-mmc 2014-01-09 11:05:32 -05:00
Chin Liang See
c5c1af2176 socfpga/dwmmc: Adding DesignWare MMC driver support for SOCFPGA
To add the DesignWare MMC driver support for Altera SOCFPGA. It
required information such as clocks and bus width from platform
specific files (SOCFPGA handoff files)

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-01-09 11:53:55 +02:00
Markus Niebel
ab71188ce8 mmc: add setdsr support
The eMMC and the SD-Card specifications describe the optional SET_DSR command.
During measurements at our lab we found that some cards implementing this feature
having really strong driver strengts per default. This can lead to voltage peaks
above the specification of the host on signal edges for data sent from a card to
the host.

Since availability of a given card type may be shorter than the time a certain
hardware will be produced it is useful to have support for this command (Alternative
would be changing termination resistors and adapting the driver strength of the
host to the used card.)

Following proposal for an implementation:

- new field that reflects CSD field DSR_IMP in struct mmc
- new field for design specific DSR value in struct mmc
- board code can set DSR value in mmc struct just after registering an controller
- mmc_startup sends the the stored DSR value before selecting a card, if DSR_IMP is set

Additionally the mmc command is extended to make is possible to play around with different
DSR values.

The concept was tested on a i.MX53 based platform using a Micron eMMC card where the default
DSR is 0x0400 (12mA) but in our design 0x0100 (0x0100) were enough. To use this feature for
instance on a mx53loco one have to add a call to mmc_set_dsr() in board_mmc_init() after
calling fsl_esdhc_initialize() for the eMMC.

Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-01-09 11:47:51 +02:00