Update the naming convention used in the network stack functions and
variables that Ethernet drivers use to interact with it.
This cleans up the temporary hacks that were added to this interface
along with the DM support.
This patch has a few remaining checkpatch.pl failures that would be out
of the scope of this patch to fix (drivers that are in gross violation
of checkpatch.pl).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This value is not used by the network stack and is available in the
global data, so stop passing it around. For the one legacy function
that still expects it (init op on old Ethernet drivers) pass in the
global pointer version directly to avoid changing that interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(Trival fix to remove an unneeded variable declaration in 4xx_enet.c)
The SPDX License List version 1.19 now contains an official entry for
the IBM-pibs license. However, instead of our suggestion "ibm-pibs",
the SPDX License List uses "IBM-pibs", with the following rationale:
"The reason being that all other SPDX License List short identifiers
tend towards using capital letters unless spelling a word. I'd prefer
to be consistent to this end".
Change the license IDs to use the official name.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This commit adapts the files that were derived from PIBS (PowerPC
Initialization and Boot Software) codeto using SPDX License
Identifiers.
So far, SPDX has not assigned an official License ID for the PIBS
license yet, so this should be considered preliminary.
Note that the following files contained incorrect license information:
arch/powerpc/cpu/ppc4xx/4xx_uart.c
arch/powerpc/cpu/ppc4xx/start.S
arch/powerpc/include/asm/ppc440.h
These files included, in addition to the GPL-2.0 / ibm-pibs dual
license as inherited from PIBS, a GPL-2.0+ license header which was
obviously incorrect. This has been removed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Conflicts:
Licenses/README
Acked-by: Stefan Roese <sr@denx.de>
Fix:
4xx_enet.c: In function 'ppc_4xx_eth_initialize':
4xx_enet.c:2029: warning: assignment from incompatible pointer type
Tested on sequoia board.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Anatolij Gustschin <agust@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix:
4xx_enet.c: In function 'ppc_4xx_eth_init':
4xx_enet.c:875:6: warning: variable 'ethgroup' set but not used [-Wunused-but-set-variable]
I used "__maybe_unused" here intentionally, since all other
alternatives to fix this compilation warning would result in more
ifdef's.
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
4xx_enet.c: In function 'enet_rcv':
4xx_enet.c:1772:21: warning: variable 'ef_ptr' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
4xx_enet.c: In function 'ppc_4xx_eth_init':
4xx_enet.c:1352: warning: format '%08x' expects type 'unsigned int', but
argument 2 has type 'volatile struct mal_desc_t *'
4xx_enet.c:1352: warning: format '%08x' expects type 'unsigned int', but
argument 3 has type 'volatile struct mal_desc_t *'
4xx_enet.c:1365: warning: format '%08lx' expects type 'long unsigned int', but
argument 3 has type 'unsigned int'
4xx_enet.c:1376: warning: format '%08lx' expects type 'long unsigned int', but
argument 3 has type 'unsigned int'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
This is long over due. All but two net drivers have been converted, but
those have now been dropped.
The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined. So here we scrub the
core code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Recieve/Receive
recieve/receive
Interupt/Interrupt
interupt/interrupt
Addres/Address
addres/address
Signed-off-by: Mike Williams <mike@mikebwilliams.com>
Only install der 4xx-EMAC interrupt handlers *after* the core
network driver is registered.
This problem was noticed on the APM Taishan 440GX board, where
the board hung upon bootup after displaying "Net:".
Signed-off-by: Stefan Roese <sr@denx.de>
The include/miiphy.h header duplicates a lot of things from linux/mii.h.
So punt all the things that overlap to keep the API simple and to make
merging between U-Boot and Linux simpler.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch starts a bit PPC4xx header cleanup. First patch mostly
touches PPC440 files. A later patch will touch the PPC405 files as well.
This cleanup is done by creating header files for all SoC versions and
moving the SoC specific defines into these special headers. This way the
common header ppc405.h and ppc440.h can be cleaned up finally.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves some ppc4xx related headers from the common include
directory (include/) to the powerpc specific one
(arch/powerpc/include/asm/). This way to common include directory is not
so cluttered with files.
Signed-off-by: Stefan Roese <sr@denx.de>
The driver name does not need to be writable, so constify it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
By defining CONFIG_M88E1111_DISABLE_FIBER boards can configure the
M88E1111 PYH to disable fiber. This is needed for an upcoming PPC460GT
based board, which has fiber/copper auto-selection enabled by default.
This doesn't seem to work. So we disable fiber in the PHY register.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Modify all existing *.c files to use the new register names
as seen in the AMCC manuals.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
On 405EZ the RX-/TX-interrupts are coalesced into one IRQ bit in the
UIC. We need to acknowledge the RX-/TX-interrupts in the
SDR0_ICINTSTAT reg as well.
This problem was introduced with commit
d1631fe1 [ppc4xx: Consolidate PPC4xx UIC defines]
Signed-off-by: James Clough <james@rtetc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch cleans up multiple issues of the 4xx register (mostly
DCR, SDR, CPR, etc) definitions:
- Change lower case defines to upper case (plb4_acr -> PLB4_ACR)
- Change the defines to better match the names from the
user's manuals (e.g. cprpllc -> CPR0_PLLC)
- Removal of some unused defines
Please test this patch intensive on your PPC4xx platform. Even though
I tried not to break anything and tested successfully on multiple
4xx AMCC platforms, testing on custom platforms is recommended.
Signed-off-by: Stefan Roese <sr@denx.de>
It was brought to our attention that U-Boot contains code derived from the
IBM OpenBIOS source code originally provided with some of the older PowerPC
4xx development boards. As a result, the original license of this code has
been carried in the various files for a number of years in the U-Boot project.
IBM is dual-licensing the IBM code contributions already present in U-Boot
under either the terms of the GNU General Public License version 2, or the
original code license already present.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch fixes a compilation warning for some Ethernet PHY-less
PPC4xx platforms (440SPE based ones) and a potential compilation
error for 440SP platforms (use of undefined 'ethgroup' variable).
In the original code and in case of 440SPE platforms, 'ethgroup'
is initialized to -1 and never modified. Later in the function,
within an #ifdef statement, an 'if statement' executes code only
if 'ethgroup' is set to 4, therefore it is harmless to avoid
executing the 'if statement' by removing the CONFIG_440SPE from
the affected #ifdefs. In case of 440SP platforms with on-board
Ethernet PHY, 'ethgroup' is undefined but used (there are not such
platforms in the repository yet). All other architectures are not
affected by this change.
Signed-off-by: Alessio Centazzo acpatin@yahoo.com
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch fixes MDIO clock setup in case when OPB frequency is 100MHz.
Current code assumes that the value of sysinfo.freqOPB is 100000000
when OPB frequency is 100MHz. In reality it is 100000001. As a result
MDIO clock is set to incorrect value, larger than 2.5MHz, thus violating
the standard. This in not a problem on boards equipped with Marvell PHYs
(e.g. Canyonlands), since those PHYs support MDIO clocks up to 8.3MHz,
but can be a problem for other PHYs (e.g. Realtek ones).
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
The drivers that get converted here:
3c589
4xx_enet
dc2114x
dm9000x
enc28j60
fsl_mcdmafec
ks8695eth
mcffec
rtl8019
rtl8169
s3c4510b_eth
xilinx_emac
xilinx_emaclite
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Rolf Offermanns <rof@sysgo.de>
CC: Stefan Roese <sr@denx.de>
CC: Sascha Hauer <saschahauer@web.de>
CC: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
CC: Greg Ungerer <greg.ungerer@opengear.com>
CC: Xue Ligong <lgxue@hotmail.com>
CC: Masami Komiya <mkomiya@sonare.it>
CC: Curt Brune <curt@cucy.com>
CC: Michal SIMEK <monstr@monstr.eu>
Also changed path in all linker scripts that reference this driver
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
