At present U-Boot always builds dtc if CONFIG_OF_CONTROL is defined, even
when DTC is provided. The built dtc is not actually used, so this is a
waste of time.
Update the Makefile logic to build dtc only if one is not provided to the
build with the DTC variable. Add documentation to explain this.
This saves about 3.5 seconds of elapsed time on a clean build of
sandbox_spl for me.
Signed-off-by: Simon Glass <sjg@chromium.org>
Brand names are supposed to be written with a capital,
so change them all.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the list of mainline U-boot supported Rockchip boards
rk3188 is placed below under the name rv3188. Give back it's
original name and sort the list in alphabetical order.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When a test hands on a real board there is no way on the console to obtain
any information about why it hung.
With sandbox we can actually find out that it died and get a signal or
exit code. Add this to make it easier to figure out what happened.
So instead of:
test/py/u_boot_spawn.py:171: in expect
c = os.read(self.fd, 1024).decode(errors='replace')
E OSError: [Errno 5] Input/output error
We get:
test/py/u_boot_spawn.py:171: in expect
c = os.read(self.fd, 1024).decode(errors='replace')
E ValueError: U-Boot exited with signal 11 (Signals.SIGSEGV)
Signed-off-by: Simon Glass <sjg@chromium.org>
This produces a lot of code output which is not very helpful and is quite
annoying to wade through. Use the short format by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Kontron SoM-Line i.MX8MM (N801x) by Kontron Electronics GmbH is a SoM
module with an i.MX8M-Mini SoC, 1/2/4 GB LPDDR4 RAM, SPI NOR, eMMC and PMIC.
The matching evaluation boards (Board-Line) have 2 Ethernets, USB 2.0, HDMI/LVDS,
SD card, CAN, RS485 and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by
Kontron Electronics GmbH.
Currently there are the following SoM flavors (SoM-Line):
* N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
* N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND
* N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND
And the according evaluation boards (Board-Line):
* N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ...
* N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ...
* N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ...
Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config
options at compile-time. Though the differences are so minor, that for
the scope of these SoMs we just use a single defconfig that is compatible
with both SoCs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
binman conversion made flashing flash.bin
and u-boot.itb necessary. Update binman config
to create a single flash.bin image again.
This updates imx8mp_evk and phyCORE-i.MX8MP as they share the
same binman config.
Updated also imx8mp_evk documentation.
Tested on phyCORE-i.MX8MP.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add documentation bits for the Radxa Zero
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: updated u200 MAINTAINERS]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Beelink GS-King X is a variant of the GS King boards but with an internal
USB to SATA bridge and advanced audio features.
[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.
Signed-off-by: Tom Rini <trini@konsulko.com>
OEM_REVISION is 32-bit unsigned number. It should be increased only when
changing software version. Therefore it should not depend on build time.
Change calculation to use U-Boot version numbers and set this revision
to date number.
Prior this change OEM_REVISION was calculated from build date and stored in
the same format.
After this change macro U_BOOT_BUILD_DATE is not used in other files so
remove it from global autogenerated files and also from Makefile.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support for the IOT2050 Basic and Advanced devices. The Basic
used the dual-core AM6528 GP processor, the Advanced one the AM6548 HS
quad-core version.
Both variants are booted via a Siemens-provided FSBL that runs on the R5
cores. Consequently, U-Boot support is targeting the A53 cores. U-Boot
SPL, ATF and TEE have to reside in SPI flash.
Full integration into a bootable image can be found on
https://github.com/siemens/meta-iot2050
Based on original board support by Le Jin, Gao Nian and Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
The devicetree binding files are in their own directory and use a simple
text format. Add a link for the binding for the /config node, since it
is otherwise hard to find.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- At this point there are a large number of Beaglebone boards, refer to
them as a family rather than a growing list.
- Reword customization as we're largely Kconfig-oriented now.
- Remove the NOR section as the relevant defconfigs have long been
removed and the general support was not updated.
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmFR2fMRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaAnAf/ZKPy3CRphbgAmbLhNQhQGpLosLcFp343
cv53gfsv1DakLRrhqMSnOQSVoTg9P22uHbooDDR9WHfZyEL6tvGZ+dgN2/wlDhDj
wbvvsM7FB+uvLVfMF3MURQBvy4dPO+FyCm/uHmry2V2uqWPw4ss+aVhxeQ5s4/oI
LpS6yaiM8UAj2GTUZSqJ1+/W7YG9N6tL73n0PDyCvSrdCkyPWqpww1rtST88SfFI
bBEWc6ksna/29haOwHQ2xopEbVxtHv2byULfqUtnsbtE4Ozw8o0fx66tdwPHTQlM
7eSuRiEbqjlJuUZFIbMat7nb7inZkaWupZ/Sr1HUUiDdKMygrRsQhg==
=x8Uf
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-next-27sep21' of https://source.denx.de/u-boot/custodians/u-boot-dm into next
Various of-platdata improvements, including CONFIG_OF_REAL
Convert some of these occurences to C code, where it is easy to do. This
should help encourage this approach to be used in new code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that we have a 'positive' Kconfig option, use this instead of the
negative one, which is harder to understand.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current API is outdated as it requires a devicetree pointer.
Move these functions to use the ofnode API and update this globally. Add
some tests while we are here.
Correct the call in exynos_dsim_config_parse_dt() which is obviously
wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
The devicetree binding files are in their own directory and use a simple
text format. Add a link for the binding for the /config node, since it
is otherwise hard to find.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Use the more generic reset-gpios property name.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Version string is available in global variable char version_string[].
Macro U_BOOT_VERSION_STRING is not used by any other file, so remove it
completely from version.h. Other files were already converted to use
variable version_string[].
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Support using mmc command for enumerating mmc card in a given mode
Fix device_remove in mmc
Fix switch issue with send_status disabled
Drop 1ms delay in fsl_esdhc command sending
Revert "mmc: sdhci: set to INT_DATA_END when there are data"
The current list is missing a few items. Add them.
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Sort these and add a type so it is clear how to set the value. Add a note
about usage to the top. Correct the 'no-keyboard' binding which is missing
a prefix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Move this documentation to the new format.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add documentation on the usage of "mmc dev" and "mmc rescan" commands to
set user defined speed modes.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Move TI maintainership to Tom.
Updated with the following commands:
find ./ -name MAINTAINERS | xargs sed -i s/"Lokesh Vutla <lokeshvutla@ti.com>"/"Tom Rini <trini@konsulko.com>"/g
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Acked-by: Tom Rini <trini@konsulko.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
Per a request from Andre Przywara and agreed with by Peter Hoyes, the
vexpress aemv8r support wasn't quite ready to be merged, but the
discussion had moved off list. We should keep the first patch in the
series for now, but revert the rest. This reverts the following
commits:
e0bd6f31ce doc: Add documentation for the Arm vexpress board configs
30e5a449e8 arm: Use armv8_switch_to_el1 env to switch to EL1
b53bbca63b vexpress64: Add BASER_FVP vexpress board variant
2f5b7b7490 armv8: Add ARMv8 MPU configuration logic
37a757e227 armv8: Ensure EL1&0 VMSA is enabled
Signed-off-by: Tom Rini <trini@konsulko.com>
This Kconfig symbol was never added to U-Boot but it was mentioned in the
origin commit c35df7c9e4 ("qemu: arm64: Add documentation for capsule
update"). That's why remove it from documentation to be accurate.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Create a new documentation section for Arm Ltd boards with a sub-page
for the vexpress board (FVP-A, FVP-R and Juno).
Document how the armv8_switch_to_el1 environment variable can be used
to switch between booting from S-EL2/S-EL1 at runtime on the BASER_FVP.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
The BASER_FVP board variant is implemented on top of the BASE_FVP board
config (which, in turn, is based on the Juno Versatile Express board
config). They all share a similar memory map - for BASER_FVP the map is
inverted from the BASE_FVP
(https://developer.arm.com/documentation/100964/1114/Base-Platform/Base---memory/BaseR-Platform-memory-map)
* Create new TARGET_VEXPRESS64_BASER_FVP target, which uses the same
board config as BASE_FVP and JUNO
* Adapt vexpress_aemv8a.h header file to support BASER_FVP (and rename
to vexpress_aemv8.h)
* Enable config to switch to EL1 for the BASER_FVP
* Create vexpress_aemv8r defconfig
* Provide an MPU memory map for the BASER_FVP
For now, only single core boot is supported.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
[trini: Add MAINTAINERS, move BOOTCOMMAND to defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Over the time, the "stemmy" U-Boot board was tested on several other
Samsung smartphones based on ST-Ericsson NovaThor Ux500. Convert the
documentation to reStructuredText at doc/board/ste/stemmy.rst and
make the device list complete. Also note that the board now boots
into USB Fastboot instead of just ending up at the U-Boot prompt.
The device table is mostly taken from the postmarketOS wiki article
(https://wiki.postmarketos.org/wiki/ST-Ericsson_NovaThor_U8500).
All the newly added devices were tested by Linus Walleij.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
This resyncs us with the version found in v5.13 of the Linux kernel with
the following exceptions:
- Keep our u-boot specific tests / code area.
- Change the location of checkpatch.rst (which we now import)
- Drop the "use strscpy" test as we don't have that, but do have strlcpy
and want that used now.
- Keep debug/printf in the list for $logFunctions
And note that we now also include the spdxcheck.py tool that
checkpatch.pl supports calling out to, and include upstream's
checkpatch.rst in our develop section of the documentation.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
All platforms define CONFIG_SYS_LOAD_ADDR, but only some define
CONFIG_LOADADDR. Very very rarely are these not the same address, and
qemu-ppce500 is one such case. However, based on reading the history of
the code, this mismatched value was simply a copy-paste from other
PowerPC platforms where it is this unused currently. Switch the code to
use CONFIG_SYS_LOAD_ADDR and update the documentation.
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
A rather common kind of external watchdog circuit is one that is kept
alive by toggling a gpio. Add a driver for handling such a watchdog.
The corresponding linux driver apparently has support for some
watchdog circuits which can be disabled by tri-stating the gpio, but I
have never actually encountered such a chip in the wild; the whole
point of adding an external watchdog is usually that it is not in any
way under software control. For forward-compatibility, and to make DT
describe the hardware, the current driver only supports devices that
have the always-running property. I went a little back and forth on
whether I should fail ->probe or only ->start, and ended up deciding
->start was the right place.
The compatible string is probably a little odd as it has nothing to do
with linux per se - however, I chose that to make .dts snippets
reusable between device trees used with U-Boot and linux, and this is
the (only) compatible string that linux' corresponding driver and DT
binding accepts. I have asked whether one should/could add "wdt-gpio"
to that binding, but the answer was no:
https://lore.kernel.org/lkml/CAL_JsqKEGaFpiFV_oAtE+S_bnHkg4qry+bhx2EDs=NSbVf_giA@mail.gmail.com/
If someone feels strongly about this, I can certainly remove the
"linux," part from the string - it probably wouldn't the only place where
one can't reuse a DT snippet as-is between linux and U-Boot.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Documentation:
* Rename Freescale to NXP
* Document structures used for the UEFI TCG2 protocol
UEFI:
* Device paths must use EfiBootServicesData
-----BEGIN PGP SIGNATURE-----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=gMKg
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-10-rc3' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-10-rc3
Documentation:
* Rename Freescale to NXP
* Document structures used for the UEFI TCG2 protocol
UEFI:
* Device paths must use EfiBootServicesData
The driver will use a syscon regmap as backend and supports both
16 and 32 size value. The value will be stored in the CPU's endianness.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
'make htmldocs' does not use file doc/board/st/st.rst because the name
matches the directory name. Let's rename it to st-dt.rst.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Having "i.MX7D/i.MX8MM SRC_GPR10 PERSIST_SECONDARY_BOOT for bootloader A/B
switching" at the top level of the documentation tree does not make sense.
Move it to board specific information.
Fixes: 59e3d1bd49 ("doc: imx: psb: Document usage of SRC_GPR10 PERSIST_SECONDARY_BOOT for A/B switching")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
TF-A for STM32MP15 now supports the FIP: it is a packaging format which
includes the secure monitor, u-boot-nodtb.bin and u-boot.dtb
This FIP file is loaded by FSBL = TF-A BL2.
This patch updates the board documentation to use this FIP file and no
more u-boot.stm32 (with STM32 image header) which is no more generated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
With device tree binding migration to yaml it is difficult to synchronize
the binding from Linux kernel to U-Boot.
Instead of maintaining the same dt bindings, this patch adds in the U-Boot
documentation the path to the device tree bindings in Linux kernel for
STMicroelectronics devices, when they are used without modification.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add links for referenced text files.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This question comes up every now and then with people coming from Linux.
Add some notes about it so we can point to it in the mailing list.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This file is about 10 years old and the updates have not covered
everything that has changed, particularly in the last few years. Update
the information and add mention of the u-boot.dtsi files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix typos.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Move this to rST format, largely unchanged to start with. Add an index
for this topic, as well as an empty intro.
Note this patch does not include updates! Is it just a conversion to the
new format. See the next patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchart <xypron.glpk@gmx.de>
Adjust the Latex formatting to match Linux v5.13.1:
* add Latex margins
* reformat the code in doc/conf.py to match Linux
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Update SeaBIOS build instructions using exact command that involves
"make olddefconfig", and mention SeaBIOS release 1.14.0 has been
used for testing.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the documentation on how to build the u-boot image for
Colibri iMX8QXP, adding support of V1.0D revision of the module.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Start out by documenting general expectations on when CI is run, how
anyone can run Azure pipelines, and how GitLab CI pipelines can be run.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Fixed broken ICH SPI driver in software sequencer mode
- Added "m25p,fast-read" to SPI flash node for x86 boards
- Drop ROM_NEEDS_BLOBS and BUILD_ROM for x86 ROM builds
- Define a default TSC timer frequency for all x86 boards
- x86 MTRR MSR programming codes bug fixes
- x86 "hob" command bug fixes
- Don't program MTRR for DRAM for FSP1
- Move INIT_PHASE_END_FIRMWARE to FSP2
- Use external graphics card by default on Intel Crown Bay
- tangier: Fix DMA controller IRQ polarity in CSRT
U-Boot mostly uses hex for value input, largely because addresses are much
easier to understand in hex.
But in some cases a decimal value is requested, such as where the value is
small or hex does not make sense in the context. In these cases it is
sometimes useful to be able to provide a hex value in any case, if only to
resolve any ambiguity.
Add this functionality, for increased flexibility.
Signed-off-by: Simon Glass <sjg@chromium.org>
These 2 options are no longer needed as now binman is used to build
u-boot.rom.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Parameter -W for sphinx-build turns build warnings into errors. This helps
us to avoid bad patches passing Gitlab CI.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The examples here are a bit messed up since the command does not match
the documentation. Use a different example instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This tool has nothing to do with testing. It is for refactoring code
automatically using a 'semantic patch' tool.
Create a new section for 'refactoring' and move it into there. It is
likely that other topics may fall under the same heading, such as
using moveconfig and search/replace tools.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this information is hidden away. Make it more visible by
putting it first, in an intro section.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We should not use /dev/sda and /dev/sdb in our examples. Users might
inadvertently mess up their workstation. Use /dev/sdX instead.
Remove console output like '# ' and '> ' which makes copying hard.
Set example language to bash for correct syntax-highlighting.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
iewed-by: Bin Meng <bmeng.cn@gmail.com>
The PWM pins on North Bridge on Armada 37xx can be configured into PWM
or GPIO functions. When in PWM function, each pin can also be configured
to drive low on 0 and tri-state on 1 (LED mode).
The current definitions handle this by declaring two pin groups for each
pin:
- group "pwmN" with functions "pwm" and "gpio"
- group "ledN_od" ("od" for open drain) with functions "led" and "gpio"
This is semantically incorrect. The correct definition for each pin
should be one group with three functions: "pwm", "led" and "gpio".
Change the "pwmN" groups to support "led" function.
Remove "ledN_od" groups. This cannot break backwards compatibility with
older device trees: no device tree uses it since there is no PWM driver
for this SOC yet. Also "ledN_od" groups are not even documented.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds the possibility to pass the PIN the OpenSSL Engine
used during signing via the environment variable MKIMAGE_SIGN_PIN.
This follows the approach used during kernel module
signing ("KBUILD_SIGN_PIN") or UBIFS image
signing ("MKIMAGE_SIGN_PIN").
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
These are out of date. Update them and point to the existing build
instructions to avoid duplication. Add a few that are missing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add usage for the setexpr command. It has been added to describe
mainly the new setexpr format string operation.
Signed-off-by: Roland Gaudig <roland.gaudig@weidmueller.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add documentation for loading firmwares to be used by remote cores in
the system including the environment variables that has to be set to
load the firmwares.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-21-kishon@ti.com
Move j721e document from board/ti/j721e/README to
doc/board/ti/j721e_evm.rst after converting it to RST format.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-20-kishon@ti.com
Documentation:
provide Makefile documentation
SMBIOS:
generate BIOS release date based on UEFI version
improve error handling in SMBIOS table generation
UEFI:
correct handling of signed capsule if authentication if off
-----BEGIN PGP SIGNATURE-----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=n6EU
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-10-rc1-3' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-10-rc1-3
Documentation:
provide Makefile documentation
SMBIOS:
generate BIOS release date based on UEFI version
improve error handling in SMBIOS table generation
UEFI:
correct handling of signed capsule if authentication if off
BIOS Release Date must be in format mm/dd/yyyy and must be release date.
U-Boot currently sets BIOS Release Date from U_BOOT_DMI_DATE macro which is
generated from current build timestamp.
Fix this issue by setting U_BOOT_DMI_DATE macro to U-Boot version which is
better approximation of U-Boot release date than current build timestamp.
Current U-Boot versioning is in format yyyy.mm so as a day choose 01.
Some operating systems are using BIOS Release Date for detecting when was
SMBIOS table filled or if it could support some feature (e.g. BIOS from
1990 cannot support features invented in 2000). So this change also ensures
that recompiling U-Boot from same sources but in different year does not
change behavior of some operating systems.
Macro U_BOOT_DMI_DATE is not used in other file than lib/smbios.c
so remove it from global autogenerated files and also from Makefile.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
* remove duplicate heading to avoid build error with 'make htmldocs'
* length of underlines must match header
* use appropriate header levels
* fix type %s/linux/Linux/
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
U-Boot uses the Linux Kbuild build system. Add the associated
documentation so that people can understand the Makefiles better.
This is taken from Linux v5.12
Signed-off-by: Simon Glass <sjg@chromium.org>
At the moment the U-Boot port for the DragonBoard 410c is designed
to be loaded as an Android boot image after Qualcomm's Little Kernel (LK)
bootloader. This is simple to set up but LK is redundant in this case,
since everything done by LK can be also done directly by U-Boot.
Dropping LK entirely has at least the following advantages:
- Easier installation/board code (no need for Android boot images)
- (Slightly) faster boot
- Boot directly in 64-bit without a round trip to 32-bit for LK
So far this was not possible yet because of unsolved problems:
1. Signing tool: The firmware expects a "signed" ELF image with extra
(Qualcomm-specific) ELF headers, usually used for secure boot.
The DragonBoard 410c does not have secure boot by default but the
extra ELF headers are still required.
2. PSCI bug: There seems to be a bug in the PSCI implementation
(part of the TrustZone/tz firmware) that causes all other CPU cores
to be started in 32-bit mode if LK is missing in the boot chain.
This causes Linux to hang early during boot.
There is a solution for both problems now:
1. qtestsign (https://github.com/msm8916-mainline/qtestsign)
can be used as a "signing" tool for U-Boot and other firmware.
2. A workaround for the "PSCI bug" is to execute the TZ syscall when
entering U-Boot. That way PSCI is made aware of the 64-bit switch
and starts all other CPU cores in 64-bit mode as well.
Simplify the dragonboard410c board by removing all the extra code that
is only used to build an Android boot image that can be loaded by LK.
This allows dropping the custom linker script, special image magic,
as well as most of the special build/installation instructions.
CONFIG_REMAKE_ELF is used to build a new ELF image that has both U-Boot
and the appended DTB combined. The resulting u-boot.elf can then be
passed to the "signing" tool (e.g. qtestsign).
The PSCI workaround is placed in the "boot0" hook that is enabled
with CONFIG_ENABLE_ARM_SOC_BOOT0_HOOK. The extra check for EL1 allows
compatibility with custom firmware that enters U-Boot in EL2 or EL3,
e.g. qhypstub (https://github.com/msm8916-mainline/qhypstub).
As a first step these changes apply only to DragonBoard410c.
Similar changes could likely also work for the DragonBoard 820c.
Note that removing LK wouldn't be possible that easily without a lot of
work already done three years ago by Ramon Fried. A lot of missing
initialization, pinctrl etc was already added back then even though
it was not strictly needed yet.
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
RTC devices could provide battery-backed memory that can be used for
storing the reboot mode magic value.
Add a new reboot-mode back-end that uses RTC to store the reboot-mode
magic value. The driver also supports both endianness modes.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A use case for controlling the boot mode is when the user wants
to control the device boot by pushing a button without needing to
go in user-space.
Add a new backed for reboot mode where GPIOs are used to control the
reboot-mode. The driver is able to scan a predefined list of GPIOs
and return the magic value. Having the modes associated with
the magic value generated based on the GPIO values, allows the
reboot mode uclass to select the proper mode.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When things go wrong it can be confusing to figure out what to change.
Add a few more details to the documentation.
Fix a 'make htmldocs' warning while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Walter Lozano <walter.lozano@collabora.com>
- Enabled distro boot for all TI platforms.
- Cleanup for AM335x Guardian Board
- PRUSS rproc on AM65 platform.
- Add PMIC support for J7200
- Misc fixes for Nokia RX-51
# Conflicts:
# arch/arm/mach-omap2/am33xx/Kconfig
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Since we removed embeddingg the capsule key into a .dtb and fixed
authenticated capsule updates for all boards, move the relevant
documentation in the efi file and update it accordingly
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Enable U-Boot bootz command and update env scripts to try loading also
zImage file and to try booting via bootz command.
Update also lowlevel_init.S code for checking validity of zImage magic to
correctly relocate kernel in zImage format.
This change allows U-Boot to directly boot Linux kernel without need for
converting kernel image into U-Boot uImage format.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210618132704.32066-1-pali@kernel.org
With the new 2021.04 we have a new version of Chromium OS boot, which
supports sandbox, coral and coral-on-coreboot. Add documentation for
this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add information about memory usage when U-Boot is started from coreboot.
This is useful when debugging. Also, since coreboot takes a chunk of
memory in the middle of SDRAM for use by PCI devices, it can help avoid
overwriting this with a loaded kernel by accident.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present only bridge devices are bound before relocation, to save space
in pre-relocation memory. In some cases we do actually want to bind a
device, e.g. because it provides the console UART. Add a devicetree
binding to support this.
Use the PCI_VENDEV() macro to encode the cell value. This is present in
U-Boot but not used, so move it to the binding header-file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
I'm no longer work in Intel, change Intel SoCFPGA co-maintainer to
Tien Fong Chee.
Signed-off-by: Ley Foon Tan <lftan.linux@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. This is also the last
of the ARCH_MPC8641/MPC8610 platforms, so remove that support as well.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is the last of the mcf547x_8x family of boards,
remove that support as well.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
- mpc8379erdb DM_USB, DM_PCI and DM_ETH support.
- Drop PCI support from the integrator family of boards
- Add synquacer support
- Assorted lpc32xx updates and improvements
- snapdragon (and related) fixes, Broadcom iproc update
Since the EDK2 GenerateCapsule script is out of date and it
doesn't generate the supported version capsule file, the document
should refer the mkeficapsule in tools.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.
For more information, see this page;
https://www.96boards.org/product/developerbox/
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
This patch adds openpiton-riscv64 SOC support. In particular, this
board supports a standard bootflow through zsbl->u-boot SPL->
opensbi->u-boot proper->Linux. There are separate defconfigs for
building u-boot SPL and u-boot proper
Signed-off-by: Tianrui Wei <tianrui-wei@outlook.com>
Signed-off-by: Jonathan Balkind <jbalkind@ucsb.edu>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
help file for using askenv cmd is created.
It provides description on the command purpose,
description of arguments,
couple of examples (illustrating command usage),
configuration parameter and
possible return values.
Signed-off-by: Adarsh Babu Kalepalli <opensource.kab@gmail.com>
Add missing entry in doc/usage/index.rst.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- x86: Discard .note.gnu.property sections
- nvme: Skip block device creation for inactive namespaces
- nvme: Convert NVMe doc to reST, and various minor fixes
Update to me as co-maintainer with Peng.
Additionally, update the mmc alias in git-mailrc.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
This patch allows uboot scripts make choices about where to boot from based
on the active mmc boot partition. This allows having two copies of kernel,
filesystems etc, and choosing which to boot from based off of the active
bootloader partition.
Signed-off-by: Reuben Dowle <reuben.dowle@4rf.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The doc says CONFIG_SKIP_LOWLEVEL_INIT is in ax25-ae350.h, while
actually it is not. Remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
On J721e and J7200, MCU R5 core (boot master) itself would run Device
Manager (DM) Firmware and interact with TI Foundational Security (TIFS)
firmware to enable DMA and such other Resource Management (RM) services.
So, during R5 SPL stage there is no such RM service available and ti_sci
driver will have to directly interact with TIFS using DM to DMSC
channels to request RM resources.
Therefore add DT binding and driver for the same. This driver will
handle Resource Management services at R5 SPL stage.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210607141753.28796-4-vigneshr@ti.com
Provide a man-page for the ums command - USB Mass Storage.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Provide a man-page for the pinmux command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reorder alphabetically the command in the index of usage
in U-Boot documentation.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At present if logging not enabled, log_info() becomes a nop. But we want
log output at the 'info' level to be akin to printf(). Update the macro to
pass the output straight to printf() in this case.
This mimics the behaviour for the log_...() macros like log_debug() and
log_info(), so we can drop the special case for these.
Add new tests to cover this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add defconfig and board support for HiFive Unmatched.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
With the last user of this driver removed, remove the driver.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Documentation:
* add a man-page for the size command
* add man-page for extension command to index
Bug fixes:
* avoid build failure due to missing SHA512 hardware acceleration
* correct error handling in TCG2 protocol
* don't let user disable capsule authentication
* correct reading directories via UEFI API
-----BEGIN PGP SIGNATURE-----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=h8yY
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-07-rc3' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-07-rc3
Documentation:
* add a man-page for the size command
* add man-page for extension command to index
Bug fixes:
* avoid build failure due to missing SHA512 hardware acceleration
* correct error handling in TCG2 protocol
* don't let user disable capsule authentication
* correct reading directories via UEFI API
'make htmldocs' results in a build warning
checking consistency... doc/usage/extension.rst:
WARNING: document isn't included in any toctree
Add the document to the index.
Fixes: 2f84e9cf06 ("cmd: add support for a new "extension" command")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This fixes two minor format issues of the ax25-ae350 reST file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This patch adds a new "extension" command, which aims at detecting
extension boards connected to the hardware platform, and apply the
Device Tree overlays that describe the hardware present on those
extension boards.
In order to enable this mechanism, board-specific code must implement
the extension_board_scan() function that fills in a linked list of
"struct extension", each describing one extension board. In addition,
the board-specific code must select the SUPPORT_EXTENSION_SCAN Kconfig
boolean.
Based on this:
- "extension scan" makes the generic code call the board-specific
extension_board_scan() function to retrieve the list of detected
extension boards.
- "extension list" allows to list the detected extension boards.
- "extension apply <number>|all" allows to apply the Device Tree
overlay(s) corresponding to one, or all, extension boards
The latter requires two environment variables to exist and set one variable
to run:
- extension_overlay_addr: the RAM address where to load the Device
Tree overlays
- extension_overlay_cmd: the U-Boot command to load one overlay.
Indeed, the location and mechanism to load DT overlays is very setup
specific.
- extension_overlay_name: set by the command: the name of the DT which
will be load during the execution.
When calling the command described in the extension_overlay_cmd
variable, the variable extension_overlay_name will be defined. So a
typical extension_overlay_cmd will look like this:
extension_overlay_cmd=load mmc 0:1 $extension_overlay_addr /boot/$extension_overlay_name
Here is an example on how to use it:
=> run loadfdt
=> fdt addr $fdtaddr
=> setenv extension_overlay_addr 0x1000
=> setenv extension_overlay_cmd 'load mmc 0:1 ${extension_overlay_addr} /boot/${extension_overlay_name}'
=> extension scan
Found 1 extension board(s).
=> extension apply 0
519 bytes read in 3 ms (168.9 KiB/s)
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
The ebreak instruction should generate a breakpoint exception.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This change would enhance the existing 'gpt read' command to allow
(optionally) writing of the read GPT partitions to an environment
variable in the UBOOT partitions layout format. This would allow users
to easily change the overall partition settings by editing said variable
and then using the variable in the 'gpt write' and 'gpt verify' commands.
Signed-off-by: Farhan Ali <farhan.ali@broadcom.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Corneliu Doban <cdoban@broadcom.com>
Cc: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
This uses the newly-added dm_gpio_get_values_as_int_base3 function to
implement a sysinfo device. The revision map is stored in the device tree.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Due to copy-paste error, two of the setexpr arguments were missing.
Add the missing arguments.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Provide a man-page for the fatinfo command.
The .rst file was lost in patch 15d9694600 ("doc: fatinfo man-page").
Fixes: 15d9694600 ("doc: fatinfo man-page")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Document the bindings for fsl,anatop-regulator
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Two external references cannot have the same name:
doc/chromium/overview.rst:5:
WARNING: Duplicate explicit target name: "youtube"
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
In reStructured text footnotes are referenced like [1]_.
Add missing underscores.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Marek Vasut <marex@denx.de>
The length of an underline must match the length of the header.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
update ls1028aqds networking protocol, config in ls1021atwr, env in ls1012a
Add seli3 board support, booke watchdog, update eTSEC support in ppc-qemu
Add DM_SERIAL and lpuart in sl28, add DM_ETH support for some of powerpc platforms
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Document how to launch a QEMU session with eTSEC as a network device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At present the Freescale TSEC node DT bindings doc requires a <reg>
property in the TSEC node. But this might not always be the case.
In the upstream Linux kernel, there is no DT bindings doc for it
but the kernel driver tests a subnode of a name prefixed with
"queue-group", as we can see from gfar_of_init():
for_each_available_child_of_node(np, child) {
if (!of_node_name_eq(child, "queue-group"))
...
in drivers/net/ethernet/freescale/gianfar.c
Update our DT bindings to describe this alternate description.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Per the upstream Linux kernel doc:
Documentation/devicetree/bindings/net/ethernet-controller.yaml
There are two ways to describe a fixed PHY attached to an Ethernet
device. This updates our dt-bindings doc to add the old DT bindings.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
An entry is missing in the FSP-S devicetree bindings, and as a result
the description for the next few following entries is off by one line.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The new correct way to load an FPGA image is to declare it in the list
of "loadables". multi-with-fpga.its used the now deprecated "fpga"
property. Since this example most likely intended to use u-boot's
generic FPGA loading code, compatible = "u-boot,fpga-legacy" is also
appropriate here.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 4afc4f37c7 ("doc: FIT image: Clarify format and simplify
syntax") introduced a "compatible" property for loadable images.
It did not define its contents. Use "u-boot,fpga-legacy" compatible
string to specify that fpga_load() should be used to load the image.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
After lots of debating, this documents how we'd like mkimage to treat
'keydir' and 'keyfile' arguments. The rest is in the docs.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement voltage regulators interfaced by the SCMI voltage domain
protocol. The DT bindings are defined in the Linux kernel since
SCMI voltage domain and regulators patches [1] and [2] integration
in v5.11-rc7.
Link: [1] 0f80fcec08
Link: [2] 2add5cacff
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This PWM is used in rk3399-gru-bob and rk3399-gru-kevin to control
the display brightness. We can only change the duty cycle, so on
set_config() we just try to match the duty cycle that dividing duty_ns
by period_ns gives us. To disable, we set the duty cycle to zero while
keeping the old value for when we want to re-enable it.
The cros_ec_set_pwm_duty() function is taken from Depthcharge's
cros_ec_set_bl_pwm_duty() but modified to use the generic pwm type.
The driver itself is very loosely based on rk_pwm.c for the general pwm
driver structure.
The devicetree binding file is from Linux, before it was converted to
YAML at 5df5a577a6b4 ("dt-bindings: pwm: Convert google,cros-ec-pwm.txt
to YAML format") in their repo.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since that invlolves external projects and not only U-Boot, add guidance
for supported platforms
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Document the command line options for efidebug and initrd loading
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Rewiewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Document SRC_GPR10 PERSIST_SECONDARY_BOOT functionality. This is useful for
reliable bootloader A/B updates, as it permits switching between two copies
of bootloader at different offsets of the same storage. The switch happens
in case one copy is corrupted OR can be enforced by user. This functionality
is present at least since i.MX53, however is poorly documented in all known
SoC datasheets, hence this document aims to clarify the usage, currently on
i.MX7D and i.MX8MM.
Signed-off-by: Marek Vasut <marex@denx.de> # Original MX7D work, this document
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io> # All the MX8M work
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@foundries.io>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Fix an URL for downloading the SCFW binary for an Apalis iMX8X
and improve u-boot image build instructions.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
In preparation to add SiFive Unmatched board support, let's rename
the existing fu540 board to unleashed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
When booting in low power or dual boot modes the M4 binary is
authenticated by the M4 ROM code.
Add an option in hab_status command so users can retrieve M4 HAB
failure and warning events.
=> hab_status m4
Secure boot disabled
HAB Configuration: 0xf0, HAB State: 0x66
No HAB Events Found!
Add command documentation in mx6_mx7_secure_boot.txt guide.
As HAB M4 API cannot be called from A7 core the code is parsing
the M4 HAB persistent memory region. The HAB persistent memory
stores HAB events, public keys and others HAB related information.
The HAB persistent memory region addresses and sizes can be found
in AN12263 "HABv4 RVT Guidelines and Recommendations".
Reviewed-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Integrate the Dockerfile from
https://source.denx.de/u-boot/gitlab-ci-runner.git as of
commit bc6130d572f1 ("Dockerfile: Remove high UID/GID") and introduce a
short rST on how to build the container.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Minor dtoc improvements
Convert CONFIG_MISC_INIT_F to Kconfig
Allow unit tests to run on any board
pylibfdt build-rule fix
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmBr+AgRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebnqQf/dZUk4cpj4q29icFJhAhG3wUkzKdKywWu
wOwHPIaUIetytpjwKTbkv0cUdel5Jhp9mvnJ2O5cRUZlVdgCH+lEQmFiq1O74Jf5
IwYBN74xZuP7+rno3ZxuKhjj2ixbpeg2A5R/o7gaevIgtu4vCK71qrj3y+unjnnt
Rd5BGaVzouMya0lS9cdkrzE1vmuLXs7ZJBvKdppaNda0VScJj+JP3NqooFKRKPU+
OeyblmtfL5lGOXFdY7Wfjg0pzv5L8fJxDaYDxf6iRWWG/X6RO6zV26MWAo28Ga+J
E3fuvl0mBqr1eAg3Cf17j4s9gRZv1tMtS6Mol1scIcBrldalVFA44g==
=x75X
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6apr21' of https://source.denx.de/u-boot/custodians/u-boot-dm
ENOSYS clean-up
Minor dtoc improvements
Convert CONFIG_MISC_INIT_F to Kconfig
Allow unit tests to run on any board
pylibfdt build-rule fix
Driver model uses quite strong conventions on error codes, but these are
currently not clearly documented. Add a description of the commonly used
errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
In newer docutils writers/latex2e/docutils.sty has a unicode character
in the comments which can in turn cause Python 3.6 at least to fail.
Pin to the previous docutils release for now.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmBi3oscHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKr+CACDQJT4hGCDwc7XFjOw
RN0aGRC6eGF4q3kL4VjBazCM1SBNs3vdVZV+bnYl3ioSNzy43K7CyFqqUlJH7CJV
dakvNn71xVoQD3Xw3+I4ALibbD/tlli4vwMOeN4KlWCIdNrRrtUOQpli0M0BVDkL
0IWMDf6OLAfw1uytubsQBVitFBQoiuE3ihSphoyTOFwQdI+xsMue5uVq+O0kDqU4
gotBzmoSq5LONyNSdpHxXqujU4oXkuOr/TsVTOoRtEkQ63zVbfNWOg951is+UaHa
F7f6W+cWdlb+HBs6TFb+Gva0TMmyWIH05jyIS52k6uFVM0tyFCOJFeZp81cjPP4L
O3KI
=ywRG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.07-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.07 cycle:
This small feature set includes the implementation of the slew rate for
the PIO4 pin controller device, and a fix for arm926ejs-based
microprocessors that avoids a crash.
Add initial support for NanoPi M4B, a minor revision of
the original NanoPi M4.
Commit details of rk3399-nanopi-m4b.dts sync from Linux 5.12-rc4:
"arm64: dts: rockchip: Add NanoPi M4B board"
(sha1: c7b03115003f7f337ab165542cee37148cf30a8a)
Signed-off-by: Alexandre Vicenzi <alexandre.vicenzi@suse.com>
Reviewed-by: Kever Yang <kever.yang@rock-cihps.com>
This probably should have been done a while back since it is a core
system. Add a migration deadline of later this year, to catch the
stragglers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide the model information through sysinfo so that it shows up on
boot. For memconfig 4 pins are provided, for 16 combinations. For SKU
ID there are two options:
- two pins provided in a ternary arrangement, for 9 combinations.
- reading from the EC
Add a binding doc and drop the unused #defines as well.
Example:
U-Boot 2021.01-rc5
CPU: Intel(R) Celeron(R) CPU N3450 @ 1.10GHz
DRAM: 3.9 GiB
MMC: sdmmc@1b,0: 1, emmc@1c,0: 2
Video: 1024x768x32 @ b0000000
Model: Google Coral (memconfig 5, SKU 3)
This depends on the GPIO series:
http://patchwork.ozlabs.org/project/uboot/list/?series=228126
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Move this documentation over to reST. Move the example files into a files/
directory so they are still separate.
Do a few minor updates while we are here:
- Tidy up sandbox build instructions
- Update my github account name
- Add some talks and links
Signed-off-by: Simon Glass <sjg@chromium.org>
At present when a file is bound to a host device it is always marked as
removeable. Arguably the device is removeable, since it can be unbound at
will. However while it is bound, it is not considered removable by the
user. Also it is useful to be able to model both fixed and removeable
devices for code that distinguishes them.
Add a -r flag to the 'host bind' command and plumb it through to provide
this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
This information is interesting to look at and can be important for
debugging and inspection. Add a command to display it in a helpful
format.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add detailed information on how to build the coral image, since it needs
binary blobs. Provide a way to avoid the memory-training delay. Also show
the console output from a sample run.
Signed-off-by: Simon Glass <sjg@chromium.org>
driver model support for of-platdata-inst
support of-platdata-inst on x86 / coral
binman support for exapanded entries
binman convert docs to reST
ti-sysc fix for duplicate uclass driver
patman minor improvements
pylibfdt build only if needed
correct obscure CI error with OF_PLATDATA_INST
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmBdZYURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreb2rQgAyr1rufrt1UGjZlVjk0HtqX0sdmcOoE4e
6NIuatWXPcP2QR93O9zeGgf/yqNIf3lVIa6Cy3baJBfP6fceZ8B24/xgKKEauPFf
g99sec+q7LPL/oigajXIaWorFXK/NDRtQcSIQFu/EmvCmi0m8Iu0HKFa7YBqa7dc
YdhGnJZZOdYuQmlKewq9q4cIr6qNtTZczsozt4PNZVgB2lKusBNyKRPZErNEFiN6
7A56bb8tcfWgGXenKVTUUcyjWRXM2tt4QtrPFedZsF6cLa8D5v4MfWMs0QBRFl/u
fMzxyeb46x0wsYBNqIBOC7DQWaU/ZeFlr5mQObIH0ypdcsUnEX98sw==
=Ld3P
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26mar21-take2' of git://git.denx.de/u-boot-dm into next
dtoc support for of-platdata-inst
driver model support for of-platdata-inst
support of-platdata-inst on x86 / coral
binman support for exapanded entries
binman convert docs to reST
ti-sysc fix for duplicate uclass driver
patman minor improvements
pylibfdt build only if needed
correct obscure CI error with OF_PLATDATA_INST
Add a link to binman's documentation and adjust the files so that it is
accessible. Use the name README.rst so it is easy to discover when binman
is installed without U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
These docs are useful for developers, not users. Move them under that
section.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Much of the content here is useful only for development. Move it under
that section.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add a description of the new features, along with internal technical
documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This doc has a few pieces that are out-of-date. Fix these. Also we have
started to use 'devicetree' instead of 'device tree' or 'device-tree'
since it is easier to see as a single term, so replace all ocurrences
accordingly.
Also move the caveats to the end, since this is a fairly solid part of
U-Boot now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The UEFI spec allows a packed array of UEFI device paths in the
FilePathList[] of an EFI_LOAD_OPTION. The first file path must
describe the loaded image but the rest are OS specific.
Previous patches parse the device path and try to use the second
member of the array as an initrd. So let's modify efidebug slightly
and install the second file described in the command line as the
initrd device path.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
At present this property is a phandle but does not have a #xxx-cells
property to match it. Add one so that is works the same as gpio and clock
phandles.
Signed-off-by: Simon Glass <sjg@chromium.org>
Instead of using a separate step for this processing, handle it while
scanning its associated driver. This allows us to drop the code coverage
exception in this case.
Note that only files containing drivers are scanned by dtoc, so aliases
declared in a file that doesn't hold a driver will not be noticed. It
would be confusing to put them anywhere other than in the driver that they
relate to, but update the documentation to say this explicitly, just in
case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move README.dfu to doc/usage/dfu.rst and convert to reStructured text.
In the long run this page should be split into two. One for the overview
and one for the dfu command. UEFI capsule updates and dfutftp should be
integrated into the overview page.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
-----BEGIN PGP SIGNATURE-----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=nIJc
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210312' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Add WATCHDOG_RESET() in MTD framework and STM32 QSPI driver
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
The Secure Channel Protocol 03 command sends control requests
(enable/provision) to the TEE implementing the protocol between the
processor and the secure element.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Simon Glass <sjg@chromium.org>
The 'reset' command now resets sandbox but does not quit it. Fix the
instructions.
Fixes: 329dccc067 ("sandbox: implement reset")
Signed-off-by: Simon Glass <sjg@chromium.org>
The existing log_ret() and log_msg_ret() macros consider an error to be
less than zero. But some function may return a positive number to indicate
a different kind of failure. Add macros to check for that also.
Signed-off-by: Simon Glass <sjg@chromium.org>
When multiple log() calls are used which don't end in newline, the
log prefix is prepended multiple times in the same line. This makes the
output look strange.
Fix this by detecting when the previous log record did not end in newline.
In that case, setting a flag.
Drop the unused BUFFSIZE in the test while we are here.
As an example implementation, update log_console to check the flag and
produce the expected output.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a second on writing tests, covering when to use Python and C, where
to put the tests, etc. Add a link to the existing Python test
documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present some of the documentation about running sandbox tests is in the
sandbox docs. It makes more sense to put it in with the other testing
docs, with a link there from sandbox. Update the documentation
accordingly.
Also add a paragraph explaining why sandbox exists and the test philosophy
that it uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
As an example of an SPL test, add a new test for loading a FIT within
SPL. This runs on sandbox_spl. For this to work, the text base is adjusted
so that there is plenty of space available.
While we are here, document struct spl_load_info properly, since this is
currently ambiguous.
This test only verifies the logic path. It does not actually check that
the image is loaded correctly. It is not possible for sandbox's SPL to
actually run u-boot.img since it currently includes u-boot.bin rather than
u-boot. Further work could expand the test in that direction.
The need for this was noted at:
http://patchwork.ozlabs.org/project/uboot/patch/20201216000944.2832585-3-mr.nuke.me@gmail.com/
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a few notes about the sandbox_spl tests, since they are special.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Add details about how to run a sandbox test directly, without using
pytest. This is more convenient for rapid development, since it is faster
and allows easier use of a debugger. Also mention sandbox_flattree as an
example of the different sandbox builds available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a comment about this option in the documentation. Also mention the
script that runs these combinations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
For systems where SPL loads fitImage, i.e. CONFIG_SPL_LOAD_FIT=y, use
u-boot.itb in the relevant documentation parts. Otherwise use u-boot.img.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a reST document to describe how to build and run U-Boot for
the QEMU ppce500 machine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This adds a new command 'addrmap' to display the address map for
non-identity virtual-physical memory mappings.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now when usbtty serial console is fixed in U-Boot enable CONFIG_USB_TTY for
Nokia RX-51 board by default.
Fix also USB product id as U-Boot ignores CONFIG_USBD_PRODUCTID macro and
include U-Boot string into USB product name to indicate usage of U-Boot.
CONFIG_CONSOLE_MUX is already used and U-Boot console is available for
all in/out devices. Therefore there is no need to have separate commands
'run sercon', 'run usbcon' and 'run vgacon', so remove them.
As space for U-Boot is limited to 256kB, enable CONFIG_OPTIMIZE_INLINING
and disable some other unused options so CONFIG_USB_TTY can be enabled.
Nokia RX-51 does not have easily accessible UART serial console so the only
option for easy debugging is to use device's keyboard+screen or this usbtty
serial console over USB.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Comparing a hex dump on the U-Boot command line with the contents of a
file on the host system is fairly easy and convenient to do manually if
it is small. But the format used hexdump by default differs from that
shown by U-Boot. Add a note about how to make them the same.
(For large dumps, writing the data to the network with tftpput, or to a
USB stick with ext4save is easiest.)
Signed-off-by: Simon Glass <sjg@chromium.org>
Update imx-atf and firmware-imx to latest released versions.
Update address of ATF_LOAD_ADDR that has changed to 0x970000 in imx-atf
commit 48733cb4e773a7584ced601de9d717efa3d73815.
Add 'O=' to make and build in separate directory as one issue has been noticed
where it was trouble building directly inside u-boot source dir. Restructure the workflow
and copy binaries after defconfig to ensure that build directory is created.
Signed-off-by: Peter Bergin <peter@berginkonsult.se>
Cc: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
As Stephen is no longer actively maintaining the uboot-test-hooks
repository, switch to using the instance on our GitLab.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
add support for the UUU commands ACmd and UCmd.
Enable them through the Kconfig option
CONFIG_FASTBOOT_UUU_SUPPORT
base was commit in NXP kernel
9b149c2a2882: ("MLK-18591-3 android: Add FSL android fastboot support")
and ported it to current mainline. Tested this patch
on imx6ul based board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This documents the way U-Boot understands partitions specifications.
This also updates the fastboot documentation for the changes in the
previous commit.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This anchor is only for the k210 partition layout, so rename it
appropriately. This keeps it from conflicting with the (to be added)
anchor for U-Boot partitions in general.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the last update of conf.py the references to U-Boot where replaced by
references to Linux.
Fix the project references in the generated documentation.
Reported-by: Simon Glass <sjg@chromium.org>
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Fixes: 98f01cf7a2 ("doc: update Kernel documentation build system")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Dump adc-keys bindings documentation from Linux kernel source tree from
commit 698dc0cf9447 ("dt-bindings: input: adc-keys: clarify
description").
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Patch-cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Patch-cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add optional properies to disable usb2 or usb3 ports, they are used
when provided ports are not used on some special platforms.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Add command oem bootbus which executes the command
``mmc bootbus <id> <arg>`` on the current fastboot mmc device
(<i> = CONFIG_FASTBOOT_FLASH_MMC_DEV) to set the eMMC boot
configuration on first update, with
<arg> = boot_bus_width reset_boot_bus_width boot_mode
$> fastboot oem bootbus:<boot_bus_width> <reset_boot_bus_width> <boot_mode>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add fastboot command oem partconf which executes the command
``mmc partconf <id> <arg> 0`` on the current <id> mmc device
to configure the eMMC boot partition with
<arg>: boot_ack boot_partition, so the command is:
$> fastboot oem partconf:<boot_ack> <boot_partition>
The partition_access argument is forced to 0 (userdata)
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
[lukma - Kconfig adjustments after merging this patch]
For SMBIOS we want to store the numeric version numbers in the tables. It
does not make sense to parse the strings. Instead, add new #defines with
the version and patchlevel.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There are quite a few available version options in U-Boot. Add a list of
the available Makefile variables and #defines, along with examples.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Sync DTS from Linux kernel for all K3 platforms
- Add MMC higher speed nodes for AM65x, J721e, J7200
- Convert Nokia RX-51 to use CONFIG_DM_MMC
- Minor fixes for LEGO MINDSTORMS
Bug fixes:
* do not allow creating of files with filenames on FAT file system
* install UEFI System Partition GUID on ESP handle
* in dtbdump.efi test tool use GUID to find ESP handle
Documentation:
* man-page for load command
* describe end of life of plat_auto
-----BEGIN PGP SIGNATURE-----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=rQaL
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-04-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-04-rc2
Bug fixes:
* do not allow creating of files with filenames on FAT file system
* install UEFI System Partition GUID on ESP handle
* in dtbdump.efi test tool use GUID to find ESP handle
Documentation:
* man-page for load command
* describe end of life of plat_auto
If the exception cannot be raised, the command returns.
Currently the return values are not all the same.
Remove the sub-chapter 'Return value'
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The K3 R5F remoteproc driver in U-Boot was upstreamed prior to the
equivalent remoteproc driver in the Linux kernel. Some of the DT
properties used in U-Boot got upstreamed using different names
in Linux kernel.
The modified property names include the R5F cluster mode configuration
property "lockstep-mode"; and three different individual R5F core config
properties - "atcm-enable", "btcm-enable" and "loczrama". The property
names were updated as follows:
lockstep-mode => ti,cluster-mode
atcm-enable => ti,atcm-enable
btcm-enable => ti,btcm-enable
loczrama => ti,loczrama
Update the K3 R5F remoteproc driver, the corresponding binding, and
all the existing usage in AM65x, J721E and J7200 dts files all at
once to use the new properties and to not break any bisectability.
Signed-off-by: Suman Anna <s-anna@ti.com>
Make mention of this feature in the core documentation so people can
discover it without looking at a header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Define a new 'SCRIPT' type for DFU entities. The downloaded data are
treated as simple u-boot's scripts and executed with run_command_list()
function.
Flashing the 'SCRIPT' entity might result in changing the 'dfu_alt_info'
environment variable from the flashed script, so add a global variable
for tracking the potential need to reinitialize the dfu_alt_info related
structures.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Define a new 'SKIP' type for the DFU entities. The flashed data for that
entity is simply ignored without returning any error values.
This allows to have one flashing procedure and images for the different
board types or variants, where each board uses only the images relevant
to it and skips the rest. This is especially usefull for the THOR
protocol, which usually transfers more than one file in a single session.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
[mszyprow: rephrased commit message and docs for easier reading, changed
subject to "dfu: add 'SKIP' entity"]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
The UEFI Self Certification Test (SCT) checks the SetTime() service with
the following steps:
* set date
* reset
* check date matches
To be compliant the sandbox should keep the offset to the host RTC during
resets. The implementation uses the environment variable
UBOOT_SB_TIME_OFFSET to persist the offset.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Espressobin: Disable slot when emmc is not present (Pali)
- DS414; config header cleanup (Phil)
- PCI: auto-config enhancement (Phil)
- pci_mvebu: Also map IO region (Phil)
- serial: a3720: Implement pending method for output direction (Pali)
- turris_mox: Enable a few commands (Marek)
- helios4 & ClearFog changes (Dennis)
- Plus some minor misc changes
Update the build system for the HTML documentation to allow using
Sphinx 3.
Man-page for exception command.
-----BEGIN PGP SIGNATURE-----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=CAW4
-----END PGP SIGNATURE-----
Merge tag 'doc-2021-04-rc1-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for documentation tag doc-2021-04-rc1-3
Update the build system for the HTML documentation to allow using
Sphinx 3.
Man-page for exception command.
This adds support for specifying FDT overlays in an extlinux/pxelinux
configuration file.
Without this, there is no simple way to apply overlays when the kernel
and fdt is loaded by the pxe command.
This change adds the 'fdtoverlays' keyword for a label, supporting multiple
overlay files to be applied on top of the fdt specified in the 'fdt' or
'devicetree' keyword.
Example:
label linux
kernel /Image
fdt /soc-board.dtb
fdtoverlays /soc-board-function.dtbo
append console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait
This code makes usage of a new variable called fdtoverlay_addr_r used to load
the overlay files without overwritting anything important.
Cc: Tom Rini <trini@konsulko.com>
Cc: Andre Heider <a.heider@gmail.com>
Cc: Jernej Škrabec <jernej.skrabec@siol.net>
Cc: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Jernej Škrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Update the documentation build system according to Linux v5.11-rc1.
Deactive the automarkup.py extension module which on Gitlab CI is
incompatible with Unicode.
With this patch we can build the HTML documentation using either of
Sphinx 2 and Sphinx 3.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Sphinx 3 builds fail due to doc/develop/logging.rst producing duplicate
labels.
Include logging.h only once in the API section and use cross-references for
the enums log_level_t and log_category_t.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When testing builds provided in https://github.com/openwrt/openwrt/pull/3360
I discovered that fdtfile was not set and as a result the firmware was not
functional. So I am documenting what is needed.
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Cc: Atish Patra <atish.patra@wdc.com>
Cc: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Karsten Merker <merker@debian.org>
* Man-pages for sbi, exit, for, echo, loady, true, false, conitrace
* Adjust suppression of newline in echo command.
* Provide unit test for echo command.
-----BEGIN PGP SIGNATURE-----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=0CgJ
-----END PGP SIGNATURE-----
Merge tag 'doc-2021-04-rc1-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for documentation tag doc-2021-04-rc1 (2)
* Man-pages for sbi, exit, for, echo, loady, true, false, conitrace
* Adjust suppression of newline in echo command.
* Provide unit test for echo command.
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
Unfortunately we now see a number of now-fatal warnings about duplicate
labels. It is often unclear how best to re-write the document in
question to not duplicate these otherwise logical headings.
This reverts commit 10a1df3cd4.
Signed-off-by: Tom Rini <trini@konsulko.com>
Convert test/py/README.md to restructured text and add it to the generated
HTML documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move test/README to the 'Develop U-Boot' chapter of the HTML documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the help message used for 'make help':
Documentation targets:
Linux kernel internal documentation in different formats from ReST:
=>
U-Boot documentation in different formats from ReST:
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update the docomentation build system according to Linux v5.11-rc1.
With this patch we can build the HTML documentation using either of
Sphinx 2 and Sphinx 3.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
[Fix warning in b4860qds.rst about "Switch Settings"]
Signed-off-by: Tom Rini <trini@konsulko.com>
** Introduction
There are currently four ways to load an OS image with u-boot
1. SPL -> u-boot -> bootm
2. SPL blue falcon mode
3. "Basic" FIT image (CONFIG_LOAD_FIT)
4. "Full-featured" FIT image (CONFIG_LOAD_FIT_FULL)
These four code paths were developed independently, and share very
little code. (3) and (4), behave very differently, are littered with
special cases. They even have different DTS syntax and properties.
The cause of this divergence is that the FIT format specification
leaves a number of things open to interpretation. The purpose of this
change is to enable the reduction of code size, duplication, and
complexity by updating and streamlining the FIT format.
We are only marginally concerned with backwards compatibility, because
we don't have inter-compatibility. For example, CONFIG_LOAD_FIT is
able to load images that CONFIG_LOAD_FIT_FULL won't. This is a direct
result of the incompatible syntax between the two implementations.
Ideally, these changes would enable "simple" FIT to be a subset of the
"full" fit implementation, and share most code. These changes should
also eliminate the need for falcon mode (although we are not
advocating for the removal of falcon mode at this time).
** Description of changes
* The "configurations" node is now mandatory
Guessing how to load components based on their "os" and "type" invites
confusion and superfluous heuristics. Instead, require each FIT image
to be explicit on how components should be loaded.
* Eliminate "ramdisk", "setup", "standalone", and "fpga" properties
Having too many special purpose properties requires special-casing
FIT loading code. When a special property can be handled by another
property, it is redundant.
- A "ramdisk" is identical to a loadable. Thus ramdisk images should
be placed under "loadables".
- A "setup" node can be achieved by using a "kernel" or "firmware"
property instead.
- "standalone" is used for u-boot nodes. The correct property to use
in this case is "firmware".
- "fpga" is a loadable
* Prioritize control between "firmware" and "kernel"
"firmware" and "kernel" are special nodes in that control is passed
to the "entry-point" of the image. Both can be present, for example,
an OP-TEE firmware with a linux kernel. When both are present,
control is passed to the "firmware" image.
** Further generalizations (not included herein)
The "firmware" and "kernel" properties could be generalized as a
"next-boot-stage", or similar name. This "next" stage would be special
in that it is both executable, and is the stage that is passed
control. For example, "next-stage" could be an op-tee image, with
linux as a loadable, or a u-boot image.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Update branch and version information of ATF and DDR firmware files to
point to latest releases provided by NXP.
This is especially critical for imx8mp evk, as the ATF support for that
SoC is only available in latest releases.
Align all SoCs from imx8m family to use identical revisions of ATF and
DDR firmware.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
- Update qemu-riscv.rst build instructions.
- Add support for SPI on Kendryte K210.
- Add Microchip PolarFire SoC Icicle Kit support.
- Add support for an early timer.
- Select TIMER_EARLY to avoid infinite recursion for Trace.
This doc describes the procedure to build, flash and
boot Linux using U-boot on Microchip MPFS Icicle Kit.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
This enables configs necessary for using SPI. The environment is saved to
the very end of SPI flash. This is unlikely to be overwritten unless the
entire flash is reprogrammed.
This also supplies a default bootcommand. It loads an image and device tree
from the first partition of the MMC. This is a minimal/least effort
bootcmd, so suggestions (especially in the form of patches) are welcome. I
didn't set up distro boot because I think it is unlikely that any
general-purpose linux distros will ever be ported to this board.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Chrstopher Obbard <obbardc@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The previous patch made the table look bad. Fix it, and leave some
space for a future element being a bit longer than the current
maximum.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
When setting aside a GPT partition for holding the U-Boot environment,
having a partition type GUID [1] indicating "Linux filesystem" (as
most tools default to) is somewhat misleading - and there's no other
well-known type GUID that is better suited. So to have a canonical
value to put into the type field, define
3de21764-95bd-54bd-a5c3-4abe786f38a8
to mean a partition holding a U-Boot environment.
This is a v5 namespace-name GUID [2], generated [3] from a namespace
of "25cbcde0-8642-47c6-a298-1a3a57cd256b" and name "U-Boot
environment".
Should future type GUIDs be defined in the context of U-Boot, it's
sensible to use that same namespace GUID.
[1] https://en.wikipedia.org/wiki/GUID_Partition_Table#Partition_type_GUIDs
[2] https://en.wikipedia.org/wiki/Universally_unique_identifier#Versions_3_and_5_(namespace_name-based)
[3] https://www.uuidtools.com/v5
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Two sibling headings can never be the same.
Fix the heading levels.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a 'mbr' command to let users create or verify MBR partition layout
based on the provided text description. The partition layout is
alternatively read from the 'mbr_parts' environment variable. This can be
used in scripts to help system image flashing tools to ensure proper
partition layout.
The syntax of the text description of the partition list is similar to
the one used by the 'gpt' command. Supported parameters are: name
(currently ignored), start (partition start offset in bytes), size (in
bytes or '-' to expand it to the whole free area), bootable (boolean
flag) and id (MBR partition type). If one wants to create more than 4
partitions, an 'Extended' primary partition (with 0x05 ID) has to be
explicitely provided as a one of the first 4 entries.
Here is an example how to create a 6 partitions (3 on the 'extended
volume'), some of the predefined sizes:
> setenv mbr_parts 'name=boot,start=4M,size=128M,bootable,id=0x0e;
name=rootfs,size=3072M,id=0x83;
name=system-data,size=512M,id=0x83;
name=[ext],size=-,id=0x05;
name=user,size=-,id=0x83;
name=modules,size=100M,id=0x83;
name=ramdisk,size=8M,id=0x83'
> mbr write mmc 0
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/+yLkACgkQ4rK92eCq
k3X/Fgf/d/11WyQrVzvpr+nN+4Wl7J+ASmoUz0yKa6ri+lbvhLgh+JXbCRKgRPWu
vNnI07pSoX/QeaMpGBU8Ztg/Onb9/pvffz4WMk1411GoyCpDFuuK3cVSIoqkPfu+
XmgSX0u4BXtve1+ZdWfVBWXawUSEDMmGR3tmz1708c/s/oYpnVeRDcqiqzJ94cWE
yt+SpMPVqMUVQ/rAGkE8ToSMxX7FusEa7SvCg4U2ikoRWs3kPpr/73+tRWlmgGxL
sW8SXSKiOmFyheSBx3d2B9n00kDYTTrQmbW9hlMilZmji7CwZYxgTCMdX0x4DeFP
RDajT2Yju1JmeM+Z8+Ke2tupzvy6QA==
=oK8C
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210113' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Enable logging features for stm32mp15 boards
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
A previous series already update STMicroelectronics emails maintainers
but some files have been omitted (Makefile, .dts, .dtsi and .rst files).
Update Patrick and my email address with the one dedicated to upstream
activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Up to now the bootefi command used the last file loaded to determine the
boot partition. This has led to errors when the fdt had been loaded from
another partition after the EFI binary.
Before setting the boot device from a loaded file check if it is a PE-COFF
image or a FIT image.
For a PE-COFF image remember address and size, boot device and path.
For a FIT image remember boot device and path.
If the PE-COFF image is overwritten by loading another file, forget it.
Do not allow to start an image via bootefi which is not the last loaded
PE-COFF image.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Update the device matrix and add build instructions.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Update the device matrix and add build instructions.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: added wetek-core2.rst to q200 MAINTAINERS and added blank lines to fix build]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for the Amlogic based libretech cc version 2.
As version 1, it is based on the s905x SoC.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: Fixed libretech-cc.rst bullet points]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
-----BEGIN PGP SIGNATURE-----
iFsEABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX/ROlgAKCRDKSWXLKUoM
IRC5AIkBzg4Sz8fQgdCiOK89k7tdFKMAnA9SYhgm4TSCzffZCJwnm78QoGAC
=4FnY
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.04
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
This has not been needed since parent information was added and we started
using indicies for references to other drivers instead of pointers. It was
kept around in the expectation that it might be needed later.
However with the latest updates, it doesn't seem likely that we'll need
this in the foreseeable future.
Drop dm_populate_phandle_data() from dtoc and driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use the U_BOOT_ prefix (i.e. U_BOOT_DRIVER) to declare a driver but
in every other case we just use DM_. Update the alias macros to use the
DM_ prefix.
We could perhaps rename U_BOOT_DRIVER() to DM_DRIVER(), but this macro
is widely used and there is at least some benefit to indicating it us a
U-Boot driver, particularly for code ported from Linux. So for now, let's
keep that name.
Signed-off-by: Simon Glass <sjg@chromium.org>
This does not get a device (struct udevice *) but a struct driver_info *
so the name is confusing.
Rename it accordingly. Since we plan to have several various of these
macros, put GET at the end instead of the middle, so it is easier to spot
the related macros.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current macro is a misnomer since it does not declare a device
directly. Instead, it declares driver_info record which U-Boot uses at
runtime to create a device.
The distinction seems somewhat minor most of the time, but is becomes
quite confusing when we actually want to declare a device, with
of-platdata. We are left trying to distinguish between a device which
isn't actually device, and a device that is (perhaps an 'instance'?)
It seems better to rename this macro to describe what it actually is. The
macros is not widely used, since boards should use devicetree to declare
devices.
Rename it to U_BOOT_DRVINFO(), which indicates clearly that this is
declaring a new driver_info record, not a device.
Signed-off-by: Simon Glass <sjg@chromium.org>
make htmldocs results in an error:
doc/android/boot-image.rst:33:
WARNING: Unparseable C cross-reference: 'struct andr_img_hdr'
Invalid C declaration: Expected identifier in nested name, got keyword:
struct [error at 6]
Follow the style prescribed in
https://www.kernel.org/doc/html/latest/doc-guide/kernel-doc.html#highlights-and-cross-references
Add missing definite article.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add documentation highlighting the steps for using the uefi capsule
update feature for updating the u-boot firmware image.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
xFSTK sources got a new home under Edison Firmware Group on GitHub [1].
Update Intel Edison documentation accordingly.
While here, fix couple of typos.
[1]: https://github.com/edison-fw
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
* Provide a tool to create a file with UEFI variables to preseed UEFI
variable store.
* Make size of UEFI variable store configurable.
* Add man pages for commands 'bootefi' and 'button'.
-----BEGIN PGP SIGNATURE-----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=2GYO
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-01-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc4
* Provide a tool to create a file with UEFI variables to preseed UEFI
variable store.
* Make size of UEFI variable store configurable.
* Add man pages for commands 'bootefi' and 'button'.
The linker script uses alphabetic sorting to group the different linker
lists together. Each group has its own struct and potentially its own
alignment. But when the linker packs the structs together it cannot ensure
that a linker list starts on the expected alignment boundary.
For example, if the first list has a struct size of 8 and we place 3 of
them in the image, that means that the next struct will start at offset
0x18 from the start of the linker_list section. If the next struct has
a size of 16 then it will start at an 8-byte aligned offset, but not a
16-byte aligned offset.
With sandbox on x86_64, a reference to a linker list item using
ll_entry_get() can force alignment of that particular linker_list item,
if it is in the same file as the linker_list item is declared.
Consider this example, where struct driver is 0x80 bytes:
ll_entry_declare(struct driver, fred, driver)
...
void *p = ll_entry_get(struct driver, fred, driver)
If these two lines of code are in the same file, then the entry is forced
to be aligned at the 'struct driver' alignment, which is 16 bytes. If the
second line of code is in a different file, then no action is taken, since
the compiler cannot update the alignment of the linker_list item.
In the first case, an 8-byte 'fill' region is added:
.u_boot_list_2_driver_2_testbus_drv
0x0000000000270018 0x80 test/built-in.o
0x0000000000270018 _u_boot_list_2_driver_2_testbus_drv
.u_boot_list_2_driver_2_testfdt1_drv
0x0000000000270098 0x80 test/built-in.o
0x0000000000270098 _u_boot_list_2_driver_2_testfdt1_drv
*fill* 0x0000000000270118 0x8
.u_boot_list_2_driver_2_testfdt_drv
0x0000000000270120 0x80 test/built-in.o
0x0000000000270120 _u_boot_list_2_driver_2_testfdt_drv
.u_boot_list_2_driver_2_testprobe_drv
0x00000000002701a0 0x80 test/built-in.o
0x00000000002701a0 _u_boot_list_2_driver_2_testprobe_drv
With this, the linker_list no-longer works since items after testfdt1_drv
are not at the expected address.
Ideally we would have a way to tell gcc not to align structs in this way.
It is not clear how we could do this, and in any case it would require us
to adjust every struct used by the linker_list feature.
One possible fix is to force each separate linker_list to start on the
largest possible boundary that can be required by the compiler. However
that does not seem to work on x86_64, which uses 16-byte alignment in this
case but needs 32-byte alignment.
So add a Kconfig option to handle this. Set the default value to 4 so
as to avoid changing platforms that don't need it.
Update the ll_entry_start() accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
This documentation has been taken from Linux commit 3d7db0f11c7a ("spi: dw:
Refactor mid_spi_dma_setup() to separate DMA and IRQ config"), immediately
before the file was deleted and replaced with a yaml version. Additional
compatible strings from newer versions have been added, as well as a few
U-Boot-specific ones.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
u_boot should be u-boot
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Convert README.bootmenu to reStructured text and move it to
usage/bootmenu.rst.
Adjust the text concerning configuration settings as these now are managed
via Kconfig.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Convert README.trace to reStructured text and move it to develop/trace.rst.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert README.NetConsole to reStructured text and move it to
doc/usage/netconsole.rst.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reformat README.commands as reStructured text and add it to the HTML
documentation as develop/commands.rst.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Due to removed function c_funcptr_sig_re building with Sphinx 3 fails.
With the patch building succeeds with a lot of warnings if the '-W' flag is
removed from doc/Makefile. Most of the documentation is correct
This follows the approach taken by the Linux kernel.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
On x86 the global data pointer is stored in register fs.
On x86_64 no register is used for the global data pointer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the full name of firmware self extracting file to make it run.
Also, don't use sudo when not needed.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
This documents the u-boot build and deployment procedure.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This patch adds support for optional vbus regulator.
It is managed on phy_power_on/off calls and may be needed for host mode.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This renames power domains to match the names on the k210 datasheet.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Reviewed-by: Rick Chen <rick@andestech.com>
How to add an emulated disk to QEMU may not be known to the user.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
patman showing email replies from Patchwork
sandbox poweroff command
minor fixes in binman, tests
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl+kJL8RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaDpAf+MajyuxlmGmFTjpyiB026aWiYE4rAn4AE
bXEDxHpOTIH4hDX7kYVWPmuKivHJo2hF0WUpIFBEAgtc2dOfjOP+mrDjBzG1Pikl
z5yuilG7eHwC1kTIkPv/tPHwDWRBI5VNwTYq0VTtffMKr8LCBo96wEYEbeYK0xdQ
kpNa9d4G+tpx20BCRgPLeOMk2pg5SVszkCCkmmPd12rO2zJ9+wWa8fwA759E93Rw
RshoRCtLNo2nEA3uJVG2aN9n3eAdM/iupDVdBLg50SFKabUxt7OcvGOC8NzGdAmT
9UbB8scvQJyI/kylGT+ghH3o2RqQGvuIRXmDyETckdkpiqK0SQvysg==
=eOGz
-----END PGP SIGNATURE-----
Merge tag 'dm-pull5nov20' of git://git.denx.de/u-boot-dm
patman status subcommand to collect tags from Patchwork
patman showing email replies from Patchwork
sandbox poweroff command
minor fixes in binman, tests
- meson64_android: don't show logo on ROM USB boot
- doc: update support matrix and fix vim3/l build instructions
- meson64: relocate config_distro_bootcmmd header
- Add a new SMBIOS parser and enable it when booting from coreboot
- Fix up various driver names to avoid dtoc warnings
- Fully enable ACPI support on Google Chromebook Coral
- Add a way to set SMBIOS properties using the devicetree
- Update existing boards to use devicetree for SMBIOS using a new
default sysinfo driver
Add information about how to set SMBIOS properties using the devicetree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a simple binding file for this, so that it is clear what this binding
directory is for.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This uclass is intended to provide a way to obtain information about a
U-Boot board. But the concept of a U-Boot 'board' is the whole system,
not just one circuit board, meaning that 'board' is something of a
misnomer for this uclass.
In addition, the name 'board' is a bit overused in U-Boot and we want to
use the same uclass to provide SMBIOS information.
The obvious name is 'system' but that is so vague as to be meaningless.
Use 'sysinfo' instead, since this uclass is aimed at providing information
on the system.
Rename everything accordingly.
Note: Due to the patch delta caused by the symbol renames, this patch
shows some renamed files as being deleted in one place and created in
another.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
- New PX30 board: Engicam PX30.Core;
- Fix USB HID support for rock960;
- Remove host endianness dependency for rockchip mkimage;
- dts update for rk3288-tinker;
- Enable console MUX for some ROCKPi boards;
- Add config-based ddr selection for px30;
This would be useful and recommended boot flow for new boards
which has doesn't have the DDR support yet in mainline.
Sometimes it is very useful for debugging mainline DDR support.
Documen it for px30 boot flow.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
This updates logging documentation with some examples of the new commands
added in the previous commits. It also removes some items from the to-do
list which have been implemented.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The functions in log.h are already mostly documented, so add them to the
generated documentation.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some commands can get very unweildy if they have too many positional
arguments. Adding options makes them easier to read, remember, and
understand.
This implementation of getopt has been taken from barebox, which has had
option support for quite a while. I have made a few modifications to their
version, such as the removal of opterr in favor of a separate getopt_silent
function. In addition, I have moved all global variables into struct
getopt_context.
The getopt from barebox also re-orders the arguments passed to it so that
non-options are placed last. This allows users to specify options anywhere.
For example, `ls -l foo/ -R` would be re-ordered to `ls -l -R foo/` as
getopt parsed the options. However, this feature conflicts with the const
argv in cmd_tbl->cmd. This was originally added in 54841ab50c ("Make sure
that argv[] argument pointers are not modified."). The reason stated in
that commit is that hush requires argv to stay unmodified. Has this
situation changed? Barebox also uses hush, and does not have this problem.
Perhaps we could use their fix?
I have assigned maintenance of getopt to Simon Glass, as it is currently
only used by the log command. I would also be fine maintaining it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX5rH/QAKCRDKSWXLKUoM
IRPAAJ9SvHR3w1qTc5W+Q5CWBUH5wJbNYQCaA4PpqZCdvyu1+nF5luL6JHhbDgw=
=hOd7
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.01-v2
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
Maxime mentioned that he feels not having the time to be an Allwinner
maintainer anymore. Take over from him.
Maxime, many thanks for your great work in the past! I hope I can still
relay the occasional technical question to you in the future.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Some drivers use macro pr_cont() for continuing a message sent via printk.
Hence if we want to convert printk messaging to using the logging system,
we must support continuation of log messages too.
As pr_cont() does not provide a message level we need a means of
remembering the last log level.
With the patch a pseudo log level LOGL_CONT as well as a pseudo log
category LOGC_CONT are introduced. Using these results in the application
of the same log level and category as in the previous log message.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
SPL is creating fit-images DT node when loadables are recorded in selected
configuration. Entries which are created are using entry-point and
load-addr property names. But there shouldn't be a need to use non standard
properties because entry/load are standard FIT properties. But using
standard FIT properties enables option to use generic FIT functions to
descrease SPL size. Here is result for ZynqMP virt configuration:
xilinx_zynqmp_virt: spl/u-boot-spl:all -82 spl/u-boot-spl:rodata -22 spl/u-boot-spl:text -60
The patch causes change in run time fit image record.
Before:
fit-images {
uboot {
os = "u-boot";
type = "firmware";
size = <0xfd520>;
entry-point = <0x8000000>;
load-addr = <0x8000000>;
};
};
After:
fit-images {
uboot {
os = "u-boot";
type = "firmware";
size = <0xfd520>;
entry = <0x8000000>;
load = <0x8000000>;
};
};
Replacing calling fdt_getprop_u32() by fit_image_get_entry/load() also
enables support for reading entry/load properties recorded in 64bit format.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add missing documentation for Xilinx ZynqMP configuration with steps how
to configure it and run it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Several drivers have been added without updating documentation.
And also some dt bindings have been moved to yaml.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add basic support for the Kontron SMARC-sAL28 board. This includes just
the bare minimum to be able to bring up the board and boot linux.
For now, the Single and Dual PHY variant is supported. Other variants
will fall back to the basic variant.
In particular, there is no watchdog support for now. This means that you
have to disable the default watchdog, otherwise you'll end up in the
recovery bootloader. See the board README for details.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix up the documentation which was lost in a merge conflict in the
conversion to RST.
Fixes: 52d3df7fef ("log: Allow LOG_DEBUG to always enable log output")
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds support for the Qualcomm QUP SPI controller that is commonly found in most of Qualcomm SoC-s.
Driver currently supports v1.1.1, v2.1.1 and v2.2.1 HW.
FIFO and Block modes are supported, no support for DMA mode is planned.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This adds kerneldocs for <timer.h>.
I don't know who should maintain doc/api/timer.rst, since the timer
subsystem seems to be maintained by SoC maintainers. MAINTAINERS is left
un-updated for the moment.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update email address of Maxime Ripard in git-mailrc to match more
recently updated entry in MAINTAINERS.
commit 9bd9b2bcbe ("MAINTAINERS: Update my email address")
commit bf8f4c4400 ("MAINTAINERS: Update email address for Maxime Ripard")
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add dt-binding for MediaTek USB3 DRD Driver which it's ported
from the Linux kernel DTS binding:
Documentation/devicetree/bindings/usb/mediatek,mtu3.txt
Commit ID:
34d0545978b6 ("dt-bindings: usb: mtu3: fix typo of DMA clock name")
Due to Dual-Role switch is not supported in Uboot, some properties
are removed or changed.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add bindings for common properties, include maximum-speed,
dr_mode and phy_type
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Octeon TX: Add NAND driver (Suneel)
- Octeon TX: Add NIC driver driver (Suneel)
- Octeon TX2: Add NIC driver driver (Suneel)
- Armada 8040: Add iEi Puzzle-M80 board support (Luka)
- Armada A37xx SPI: Add support for CS-GPIO (George)
- Espressobin: Use Linux model/compatible strings (Andre)
- Espressobin: Add armada-3720-espressobin-emmc.dts from Linux (Andre)
- Armada A37xx: Small cleanup of config header (Pali)
Sphinx.override_domain() is deprecated since Sphinx 1.8 and removed in
Sphinx 3.
Use Sphinx.add_domain(, override=True) instead.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add the description of the global data pointer to the generated HTML
documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
To simplify configuration and keep synchronized the PStore/Ramoops between
U-Boot and the Linux kernel, this commit dynamically adds the Ramoops
parameters defined in the U-Boot session to the Device Tree.
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This patch adds a new pstore command allowing to display or save ramoops
logs (oops, panic, console, ftrace and user) generated by a previous
kernel crash.
PStore parameters can be set in U-Boot configuration file, or at run-time
using "pstore set" command. Records size should be the same as the ones
used by kernel, and should be a power of 2.
This command allows:
- to display uncompressed logs
- to save compressed or uncompressed logs, compressed logs are saved as a
compressed stream, it may need some work to be able to decompress it,
e.g. adding a fake header:
"printf "\x1f\x8b\x08\x00\x00\x00\x00\x00\x00\x00" |
cat - dmesg-ramoops-0.enc.z | gzip -dc"
- ECC part is not used to check memory corruption
- only 1st FTrace log is displayed or saved
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
[trini: Minor updates for current design, correct spacing in rST]
Signed-off-by: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Import armada-3720-espressobin-emmc.dts from Linux, but use sdhc1 for
emmc, since our dtsi is still based on downstream and sdhc0 is used for
the sd card.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Add documentation about 'required-mode' property in /signature node
in U-Boot's control FDT.
Signed-off-by: Thirupathaiah Annapureddy <thiruan@linux.microsoft.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
doc/README.log was already moved to doc/develop/logging.rst but has been
recreated by an incorrect merge.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present if CONFIG_LOG enabled, putting LOG_DEBUG at the top of a file
(before log.h inclusion) causes _log() to be executed for every log()
call, regardless of the build- or run-time logging level.
However there is no guarantee that the log record will actually be
displayed. If the current log level is lower than LOGL_DEBUG then it will
not be.
Add a way to signal that the log record should always be displayed and
update log_passes_filters() to handle this.
With the new behaviour, log_debug() will always log if LOG_DEBUG is
enabled.
Move log_test_syslog_nodebug() into its own file since it cannot be made
to work where it is, with LOG_DEBUG defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a script to process HPS handoff data and generate a header
for inclusion in u-boot specific devicetree addons. The header
should be included in the top level of u-boot.dtsi.
Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
The Fully-Programmable Input/Output Array (FPIOA) device controls pin
multiplexing on the K210. The FPIOA can remap any supported function to any
multifunctional IO pin. It can also perform basic GPIO functions, such as
reading the current value of a pin. However, GPIO functionality remains
largely unimplemented (in favor of the dedicated GPIO peripherals).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This normalizes the documentation to conform to kernel-doc style [1]. It
also moves the documentation for pinctrl_ops inline, and adds argument and
return-value documentation. I have kept the usual function style for these
comments. I could not find any existing examples of function documentation
inside structs.
[1] https://www.kernel.org/doc/html/latest/doc-guide/kernel-doc.html
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The pinmux property allows for smaller and more compact device trees,
especially when there are many pins which need to be assigned individually.
Instead of specifying an array of strings to be parsed as pins and a
function property, the pinmux property contains an array of integers
representing pinmux groups. A pinmux group consists of the pin identifier
and mux settings represented as a single integer or an array of integers.
Each individual pin controller driver specifies the exact format of a
pinmux group. As specified in the Linux documentation, a pinmux group may
be multiple integers long. However, no existing drivers use multi-integer
pinmux groups, so I have chosen to omit this feature. This makes the
implementation easier, since there is no need to allocate a buffer to do
endian conversions.
Support for the pinmux property is done differently than in Linux. As far
as I can tell, inversion of control is used when implementing support for
the pins and groups properties to avoid allocating. This results in some
duplication of effort; every property in a config node is parsed once for
each pin in that node. This is not such an overhead with pins and groups
properties, since having multiple pins in one config node does not occur
especially often. However, the semantics of the pinmux property make such a
configuration much more appealing. A future patch could parse all config
properties at once and store them in an array. This would make it easier to
create drivers which do not function solely as callbacks from
pinctrl-generic.
This commit increases the size of the sandbox build by approximately 48
bytes. However, it also decreases the size of the K210 device tree by 2
KiB from the previous version of this series.
The documentation has been updated from the last Linux commit before it was
split off into yaml files.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reformat the command line options chapter so that the command line options
clearly stand out.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAl97ReAACgkQd9zb2sjI
SdHHVA/9HuEAzwuJyJoyQcXARIqMwoi6w4qntlmb+VTnxxlKCzLL1Ir68W2+5Y5S
l+sVkxYDwTmYRs40FOnMdFM1r1Q7IqWwTemqQAcfmGLV+/+MwoDiludGat7JAp1i
mo/FBcBMLrf3dIJnhCyl2Rezgu06GLCQMAJOlusTDaruUZUHBxPVpAhfRvtlYq1Q
bCINZfgMcmv8EfReIOE6xGt0+9TKILqQamMByc2ZWdz5UBioqUdQ82arW1rdV/ze
ATU7vrxNmNlUQnRsMBOry9chbeuNrAhD8sqVloGPUikhf93y0BG7eINmCYrLoXjN
mopApyWzo3+50GI6It+P9vX6mWVJhd8gAJsvTkRn8ok3flGlRQPmFmAfkjngN/GH
wdkZpKi/u/ndm2Id7ekZff/Fm/ZmL/kskrRWaWrnuxHNiSNiJvAl+PU7MzCGrgED
E0MduY1hFpa7wc47xFtI0WKlcdNVQCTRwuZYVIZYlnhXeVupJyQ0dx1ggonlvvIZ
3cgS2qzd8z2RxKzhnRDvjSfwy7gWFjqpljocyRP4osoWJybJu88MIUFK2GlPdc7x
3UD/+R88FsIVsQuxzbwBuFZnP+Zo1JqCmspyX4sCeUBDNK4+MqOqIxBZry+q4qso
usWrTofg2hfxS3FgUL0pQW5GF8JGm4uXcIjbe7fMi47GJ6Lp/ec=
=rbAX
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20201005' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- generate unique mac address from SoC serial on S400 board
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
an USB3.0 Type A connector and a M.2 Key M slot.
The PHY driving these differential lines is shared between
the USB3.0 controller and the PCIe Controller, thus only
a single controller can use it.
This adds this dynamic switching right before booting Linux
and the configuration steps in the boards documentation.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[narmstrong: fixed warning by replacing min() by min_t()]
Some Espressobin boards got assigned more than one MAC address. Update
instructions how to correctly store and preserve all MAC addresses.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andre Heider <a.heider@gmail.com>
This commit adds a generic udp protocol framework in the
network loop. So protocol based on udp may be implemented
without modifying the network loop (for example custom
wait magic packet).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Dump SCMI DT bindings documentation from Linux kernel source
tree v5.8-rc1.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the boot flow description add the RESET and BOOT button as well as the
function of the DTR and RTS lines of the serial interface.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add a description of how to flash Edison using the xFSTK tool.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Some boards want to reserve extra regions of memory. Add a 'chosen'
property to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some devices can wake the system from sleep, e.g opening the lid on a
clamshell or moving a USB mouse.
Add a wake to specify this for USB devices and add the settings for Apollo
Lake.
Signed-off-by: Simon Glass <sjg@chromium.org>
Many I2C devices produce roughly the same ACPI data with just things like
the GPIO/interrupt information being different.
This can be handled by a generic driver along with some information in the
device tree.
Add a generic i2c driver for this purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Recent versions of Chrome OS do not have a kernel in the root disk, to
save space.
With the improvements to the 'zboot' command it is fairly easy to load
the kernel from the raw partition. Add instructions on how to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
A few things have changed since this was written about 18 months ago.
Update the README.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The term eMMC is used inconsistently within the FSP devicetree
bindings (e-mmc and emmc), especially for "emmc-host-max-speed"
documentation and code disagree.
Change all eMMC instances within the FSP bindings to consistently
use "emmc". The term "emmc" is already used a lot within U-Boot,
while "e-mmc" is only used in the FSP bindings.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct one typo in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The Toradex product is called apalis-imx8 consisting of SoM with
i.MX8QM and i.MX8QP SoCs.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The Toradex product is called colibri-imx8x consisting of SoM with
i.MX8QXP and i.MX8DX SoCs.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
add DM/DTS support for the UEC ethernet on QUICC Engine
Block.
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Patch-cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Patch-cc: Madalin Bucur <madalin.bucur@oss.nxp.com>
Series-changes: 3
- revert:
commit "3374264df97b" ("drivers: net: qe: deselect QE when DM_ETH is enabled")
as now qe works with DM and DM_ETH support.
- fix mailaddress from Holger
Series-changes: 2
- add comments from Qiang Zhao:
- add device node documentation
- I did not drop the dm_qe_uec_phy.c and use drivers/net/fsl_mdio.c
because using drivers/net/fsl_mdio.c leads in none existent
udevice mdio@3320
instead boards with DM ETH support should use now this
driver.
- remove RFC tag
Commit-notes:
- I let the old none DM based implementation in code
so boards should work with old implementation.
This Code should be removed if all boards are converted
to DM/DTS.
- add the DM based qe uec driver under drivers/net/qe
- Therefore copied the files uccf.c uccf.h uec.h from
drivers/qe. So there are a lot of Codingstyle problems
currently. I fix them in next version if this RFC
patch is OK or it needs some changes.
- The dm based driver code is now under drivers/net/qe/dm_qe_uec.c
Used a lot of functions from drivers/qe/uec.c
- seperated the PHY specific code into seperate file
drivers/net/qe/dm_qe_uec_phy.c
END
The K3 J7200 SoCs have two dual-core Arm R5F clusters/subsystems, with
2 R5F cores each, one in each of the MCU and MAIN voltage domains.
These clusters are a revised version compared to those present on
J721E SoCs. Update the K3 R5F remoteproc bindings with the compatible
info relevant to these R5F clusters/subsystems on K3 J7200 SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Add support for defining raw fastboot partitions in eMMC by specifying
the offset and size in an environment variable. Optionally, the eMMC
hardware partition number may also be specified.
This makes it possible to e.g. update only part of the eMMC boot
partition, instead of having to write the entire partition.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
Include information about permanent ethernet MAC address and add link how
to build ATF as U-Boot on Espressobin cannot be flashed without ATF.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- Sipeed Maix support S-mode.
- Provide command sbi.
- Use fdtdec_get_addr_size_auto_parent to get fu540 cache base address.
- Fix a compiler error with CONFIG_SPL_SMP=n.
- Fix sifive ram driver 32 compiler warnings.
- Fix kendryte/pll.h redefine nop() warning.
Provide a defconfig that can be used to build U-Boot for the Maix boards
running upon OpenSBI.
Update the documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
setenv -e -i <address>,<filesize> can be used to set a UEFI variable
from memory.
For separating an address and a size we use ':' in most commands.
Let's do the same for setenv -e -i.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
* UEFI variables can be persisted
* describe that the sequence of files loaded before bootefi matters
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
binman fixes for portage
various minor fixes
'bind' command improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl9BbZcRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZZiQf/UVsriftmxdDz3Lvbz7Jw6UCBXbeM3UN8
KgRxVll3kurZeu8bIcjAPY4YRrbWRqSXmZTXpZWgbyZzHLM4RnkamY3KF3DoxPjc
cbskd/fr4nPjSZVFrkzrvD+D5bhm+VrMtf861AkbAqqpG+Q1FmWHgApqOL1fXn3s
2VoMxRz8Cn9KkSDmxaCtJnLX77GVYYdfgii7RuNWGDqr3eBWrzflV38VbPHLplEg
VLqaLBe3G4zVwElA9Nc2hXpZB84KZEETHcBnmCzNkrSYTN2ofvSeZrWbtRztQFhz
yKur1y7jFsryRkMfxBzgldsKFRNnPT9vr+0qGtrztHjCmvhDkx1YMg==
=iDRJ
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-22aug20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
replace devfdt_get_addr_ptr() with dev_read_addr_ptr()
binman fixes for portage
various minor fixes
'bind' command improvements
Add documentation in doc/drivel-model for the bind/unbind command.
Part of this documentation is extracted from original patch commit
message:
commit 49c752c93a ("cmd: Add bind/unbind commands to bind a device to a driver from the command line")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide the required settings for the debug UART.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
The MAIXDUINO runs fine with the sipeed_maix_bitm_defconfig but a different
board id parameter should be passed to kflash.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
The test flags used by driver model are currently not available to other
tests. Rather than creating two sets of flags, make these flags generic
by changing the DM_ prefix to UT_ and moving them to the test.h header.
This will allow adding other test flags without confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
* Move README.clang to doc/build/clang.rst and reformat as
reStructeredText.
* Indicate that -ffixed-r9 and -ffixed-x18 are used to reserve registers
for gd.
* Minor editing.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add missing parameters to support full configuration of the latest FSP
MR6 release.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- Configuration changed, mainly several "CONFIG_..." moved from
s5p4418_nanopi2.h to s5p4418_nanopi2_defconfig and USB related
configs removed because USB is not supported yet.
- s5p4418_nanopi2.h: "CONFIG_" removed from several s5p4418/nanopi2
specific defines because the appropriate values do not need to be
configurable.
- pinctrl is supported now, therefore "CONFIG_PINCTRL=y" added to
s5p4418_nanopi2_defconfig.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- livetree API (dev_read_...) is used instead of fdt one (fdt...).
- doc/device-tree-bindings/pinctrl/nexell,s5pxx18-pinctrl.txt added.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- i2c/nx_i2c.c: Some adaptions mainly because of changes in
"struct udevice".
- several Bugfixes in nx_i2c.c.
- the driver has been for s5p6818 only. Code extended appropriately
in order s5p4418 is also working.
- "probe_chip" added.
- pinctrl-driver/dt is used instead of configuring the i2c I/O-pins
in the i2c-driver.
- '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where
possible (and similar).
- livetree API (dev_read_...) is used instead of fdt one (fdt...).
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Snapdragon SoCs and IPQ40xx use common TLMM IP,
so existing driver supports IPQ40xx as well.
So lets simply add a compatible for IPQ40xx.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
IPQ40xx and currently supported Snapdragon boards don't use the same one
so enable reading it from DT, if no DT property is found default value
is the same as the previous define.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
cleanups
- fsl-crypto: RNG support and bug fixes
The eSDHC adapter card identification and multiplexing configuration
through FPGA had been implemented in both common mmc driver and
fsl_esdhc driver. However it is proper to move these code to board
files and do it during board initialization. The FPGA registers are
also board specific.
This patch is to move eSDHC adapter card identification and
multiplexing configuration from mmc driver to specific board files.
And the option CONFIG_FSL_ESDHC_ADAPTER_IDENT is no longer needed.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[Rebased, Removed T1040QDS change as board does not exist]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Communication with some SPI slaves just won't cut it if these delays
(before the beginning, and after the end of a transfer) are not added to
the Chip Select signal.
These are a straight copy from Linux:
Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt
drivers/spi/spi-fsl-dspi.c
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a new documentation file for UCLASS_SOC and its usage to describe
the SoC Device ID framework that allows SoC identification and device
data matching.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Normally the FIT timestamp is created the first time mkimage is run on a
FIT, when converting the source .its to the binary .fit file. This
corresponds to using the -f flag. But if the original input to mkimage is
a binary file (already compiled) then the timestamp is assumed to have
been set previously.
Add a -t flag to allow setting the timestamp in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Fix SiFive HiFive Unleashed board booting failure problem.
- Enable SiFive fu540 PWM driver.
- Support SiFive fu540: SPI boot.
- Update OpenSBI used for RISC-V CI testing.
- Revert "riscv: Allow use of reset drivers".
- Revert "Revert "riscv: sifive: fu540: Add gpio-restart support"".
- sysreset: syscon:
- Don't assume default value for offset and mask property.
- Support value property.
- qemu: Add syscon reboot and poweroff support.
- Fix SIFIVE debug serial dependency.
- Fix linking error when building u-boot-spl with no SMP support.
- AE350 use fdtdec_get_addr_size_auto_noparent to parse smc reg.
- Make memory node available to SPL in hifive-unleashed-a00-u-boot.dtsi
- SiFive fu540 avoid using hardcoded ram base and size.
Add booting from SPI for SiFive Unleashed board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Add a new documentation file for UCLASS_SOC and its usage to describe
the SoC Device ID framework that allows SoC identification and device
data matching.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Normally the FIT timestamp is created the first time mkimage is run on a
FIT, when converting the source .its to the binary .fit file. This
corresponds to using the -f flag. But if the original input to mkimage is
a binary file (already compiled) then the timestamp is assumed to have
been set previously.
Add a -t flag to allow setting the timestamp in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This currently excludes the temporary memory used to start up the APs.
Add it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
When update_uboot.its is used directly there is syntax error for no reason.
Error report:
mkimage -f update_uboot.its boot
Error: update_uboot.its:18.12-13 syntax error
FATAL ERROR: Unable to parse input tree
mkimage: Can't read boot.tmp: Invalid argument
Fixes: 4bae90904b ("Automatic software update from TFTP server")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove the incorrect usage of double underscores for the
CONFIG_OF_LIST and CONFIG_SPL_OF_LIST symbols.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Some code was not converted by coccinelle, somehow.
I manually fixed up the remaining, and comments, README docs.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
[trini: Add arch/arm/mach-davinci/include/mach/sdmmc_defs.h and
include/fdt_support.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move doc/README.coccinelle to doc/develop/coccinelle.rst using the current
linux-next version of the text.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This chip is used on coral and we need to generate ACPI tables for sound
to make it work. Add a driver that does just this (i.e. at present does
not actually support playing sound).
Signed-off-by: Simon Glass <sjg@chromium.org>
[bmeng: Use the correct acpi_irq_polarity enum number]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This chip is used on coral and we need to generate ACPI tables for sound
to make it work. Add a driver that does just this (i.e. at present does
not actually support playing sound).
Signed-off-by: Simon Glass <sjg@chromium.org>
Some devices such as GPIO need to override the normal path that would be
generated by driver model. Add a device-tree property for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
For many device types it is possible to figure out the name just by
looking at its uclass or parent. Add a function to handle this, since it
allows us to cover the vast majority of cases automatically.
However it is sometimes impossible to figure out an ACPI name for a device
just by looking at its uclass. For example a touch device may have a
vendor-specific name. Add a new "acpi,name" property to allow a custom
name to be created.
With this new feature we can drop the get_name() methods in the sandbox
I2C and SPI drivers. They were only added for testing purposes. Update the
tests to use the new values.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a /chosen property to control the order in which the data appears
in the SSDT. This allows matching up U-Boot's output from a dump of the
known-good data obtained from within Linux.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With DDR4, Intel SOCs take quite a long time to init their memory. During
this time, if the user is watching, it looks like SPL has hung. Add a
message in this case.
This works by adding a return code to fspm_update_config() that indicates
whether MRC data was found and a new property to the device tree.
Also add one more debug message while starting.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Tested-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Some distributions provide UEFI binaries like Shim that have been signed
using a Microsoft certificate. Provide the download paths for the public
keys.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The `fitupd' command is not used by any board. The `dfu tftp' command
provides the same capabilities.
So let's drop the `fitupd' command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Up to now UEFI variables where stored in U-Boot environment variables.
Saving UEFI variables was not possible without saving the U-Boot
environment variables. With this patch series file ubootefi.var in the
EFI system partition is used for saving UEFI variables. Furthermore the
UEFI variables are exposed for reading at runtime.
Code corrections for UEFI secure boot are provided.
A buffer overrun in the RSA library is fixed.
-----BEGIN PGP SIGNATURE-----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=kJZO
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc1-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc1 (3)
Up to now UEFI variables where stored in U-Boot environment variables.
Saving UEFI variables was not possible without saving the U-Boot
environment variables. With this patch series file ubootefi.var in the
EFI system partition is used for saving UEFI variables. Furthermore the
UEFI variables are exposed for reading at runtime.
Code corrections for UEFI secure boot are provided.
A buffer overrun in the RSA library is fixed.
The documentation states that SPL is enabled in all config options
for the da850. This incorrect, because devices booting from NOR
do not need the SPL to do the low level initializion because when
booting from NOR, the board is able to execute in place (XIP)
This also clarifies that SPL isn't only used for booting from SPI,
because it is also used for booting from MMC and NAND for those
devices supporting those boot options.
Signed-off-by: Adam Ford <aford173@gmail.com>
We currently have two implementations of UEFI variables:
* variables provided via an OP-TEE module
* variables stored in the U-Boot environment
Read only variables are up to now only implemented in the U-Boot
environment implementation.
Provide a common interface for both implementations that allows handling
read-only variables.
As variable access is limited to very few source files put variable
related definitions into new include efi_variable.h instead of efi_loader.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
All SPI drivers are converted to DM_SPI but 3 drivers
still operate in nondm mode for SPL due to footprint
constraints.
Update the migration status for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Update documentation to reflect the new phandle support when OF_PLATDATA
is used. Now phandles are implemented as pointers to U_BOOT_DEVICE,
which makes it possible to get a pointer to the actual device.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the documentation with the support for driver aliases using
U_BOOT_DRIVER_ALIAS.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Drop it.
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This solves a compatibility issue with Linux device trees
that contain TPMv2.x hardware. So it's easier to import DTS
from upstream kernel when migrating board init from C code
to DTS.
The issue is that fallback binding is different between Linux
and u-Boot.
Linux: "tcg,tpm_tis-spi"
U-Boot: "tis,tpm2-spi"
As there are currently no in-tree users of the U-Boot binding,
it makes sense to use Linux fallback binding.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Odroid C4 is an Amlogic SM1 device, the board config and board documentation
are adapted from the Odroid-N2 support from the same vendor.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: fix odroid-c4.rst typos and structure]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
The PLL1 node (st,pll1) is optional in device tree, the max supported
frequency define in OPP node is used when the node is absent.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Explicitly pass the "-bios" option to QEMU to run U-Boot, instead
of the "-kernel" option, as we know that "-bios" behavior will be
changed since QEMU 5.1.0.
This also updates validated QEMU version to 5.0.0.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
This patch adds documentation for the Sipeed Maix bit, and more generally
for the Kendryte K210 processor.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This patch adds a generic reset driver. It is designed to be useful when
one has a register in a regmap which contains bits that reset other
devices. I thought this seemed like a very generic use, so here is a
generic driver. The overall structure has been modeled on the syscon-reboot
driver.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This type of bus is used in Linux to designate buses which have power
domains and/or clocks which need to be enabled before their child devices
can be used. Because power domains are automatically enabled before probing
in U-Boot, we just need to enable any clocks present.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Due to the large number of clocks, I decided to use the CCF. The overall
structure is modeled after the imx code. Clocks parameters are stored in
several arrays, and are then instantiated at run-time. There are some
translation macros (FOOIFY()) which allow for more dense packing.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
CC: Lukasz Majewski <lukma@denx.de>
CCF clocks should always use the struct clock passed to their methods for
extracting the driver-specific clock information struct. Previously, many
functions would use the clk->dev->priv if the device was bound. This could
cause problems with composite clocks. The individual clocks in a composite
clock did not have the ->dev field filled in. This was fine, because the
device-specific clock information would be used. However, since there was
no ->dev, there was no way to get the parent clock. This caused the
recalc_rate method of the CCF divider clock to fail. One option would be to
use the clk->priv field to get the composite clock and from there get the
appropriate parent device. However, this would tie the implementation to
the composite clock. In general, different devices should not rely on the
contents of ->priv from another device.
The simple solution to this problem is to just always use the supplied
struct clock. The composite clock now fills in the ->dev pointer of its
child clocks. This allows child clocks to make calls like clk_get_parent()
without issue.
imx avoided the above problem by using a custom get_rate function with
composite clocks.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiQkHUH+J02LLC9InKPlOlyTyXBgFAl76U4wACgkQKPlOlyTy
XBhKeg/6Au6lPC5QLnjEO5gpuhI/eF555jRoABXUNoM8FUjkcqA207Sgd3iTH9lS
imOGHkzwipYno5pY1UoiXr7RKJgAkJfKYWRrZ46qgITrEkgQ8Xyp46xIqhoHvpuH
Qs1YeDllHeRViBt2ZP6UJsYfUIA9xnU/o9tLh4lx2SiCPWbNDns7cB0Ajazh47Cx
8UT2ZwbATaaFfN9m4Lg65O6Fe1G/cHAw5H/xsDajpVOpskHk0RZxRxzob6XLQete
sVkZdjYmH7zG+7THLkPriu2y/qlc5t2re3OeAr/5YwYJODnj3aN7iI20Sl9xMwDP
eDcSt19HMs+Ng60+yqwHxoU+AQ2BjswYHssb2vdY8OQhlRpoFke6nT+oQtCQCYhZ
At/b2O8kh9IM9alsc8xltMABLgrOhREfxC6VQg7bsCH01+qcojGX8dhVQrYsWkKQ
GrCs6SAl8zR78j8s3OGSsvTczMkTrBTglYWIYrlvA5fFhVg5Yz38S+ioTqPc4QDc
ZJ9bDDO00CY4hJC8sx4TQcsn0OmSJeN394dy6CUoxL6fEXBdRmNRLBUnmuTmPmYT
suLB9qaG+Q6cEttXjfNN1VotSG+61COUZ0uoed47cGUo8AxLMTEe62twUc0aDPNS
NMUoMwHqVbivaGUBfG16mu8bnVfaCqFyR/LLGa6J3yQSQ8qeu30=
=dnTK
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-06-29' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips into next
- net: pcnet: cleanup and add DM support
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXvScEQAKCRDKSWXLKUoM
IeHUAJ9Z1shAlbILuHZKEpqQySLHdUVgBQCff8Nf+wi1rByTrwflKt14MtIsdFY=
=2Yuu
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.10
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
Add a short description in the ZYNQ documentation how to prepare a SD card and
copy the related images to SD card.
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The correct name for the property is "qca,clk-out-frequency", so fix
it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Move the natural text Amlogic board README files to doc/board/amlogic
into reStructuredText and :
- add reStructuredText markup for bash code
- fix secondary titles markup
- move board support into global support matrix
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
change to how sequence numbers are assigned to devices
minor fixes and improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl7kQ4kRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZrvAgAqc/TEj7QHPyW9rQSl8h65MXK93qRsnZo
4segKEtK0Rmv0S2VfmPCwujsDFl5gZUNt+rXD/l7F0a4Wzx4eYgYrEXOYsXs/ZHP
jjGrcbvO4Qkx3QzjMqqoUiQqeCgNQ9XIre8F+1NmZeQ2bFtPKbJXtXKYTcMI1wSW
PhRGbbsTnKNKC0dL0nLFG6+NC/sk6xRqMx28Ip38FTrQL+Uh67LZFpLkY3yuHo/1
CVhCw+7Aov0I6tDrdKrngjFqXRSoTsuOhavSFoW9U6llqDL7FIC6aoRo7x24lSJN
VFTRpXPmNHeslE6NHEOQs9elFpbxXR34te3k4p74rFuX/J/490UaYA==
=172C
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-12jun20' of git://git.denx.de/u-boot-dm into next
patman improvements to allow it to work with Zephyr
change to how sequence numbers are assigned to devices
minor fixes and improvements
This documents the u-boot installation procedure and the
hardware in order to get started.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
[trini: Add MAINTAINERS entry for doc file per Soeren's request]
Convert README.log to reStructuredText and add it to the generated HTML
documentation.
Assign doc/develop/logging.rst to the maintainer of LOGGING.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace CONFIG_(SPL_)MAX_LOG_LEVEL by the correct name as defined in
common/Kconfig:
line 668:config LOG_MAX_LEVEL
line 688:config SPL_LOG_MAX_LEVEL
line 708:config TPL_LOG_MAX_LEVEL
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Acked-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Document SPI flash program steps for rockchip platforms.
Suggested-by: Hugh Cole-Baker <sigmaris@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change the compatible string to "fsl,etsec2" for the Ethernet ports,
which is used in the current driver's match table.
Fixes: 69a00875e3 ("doc: dt-bindings: Describe Freescale TSEC ethernet controller")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
OpenSBI generic platform support provides platform specific
functionality based on the FDT passed by previous booting stage.
Depends on OpenSBI commit:
platform: Add generic FDT based platform support
(sha1: f1aa9e54e00006ae70aeac638d5b75093520f65d)
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
With sifive_fu540_defconfig:
User can use FSBL or u-boot-spl.bin anyone at a time.
For FSBL,
fsbl->fw_payload.bin (opensbi + U-Boot)
For u-boot-spl.bin,
u-boot-spl.bin->FIT image (opensbi + U-Boot proper + dtb)
U-Boot SPL will be loaded by ZSBL from SD card (replace fsbl.bin with
u-boot-spl.bin) and runs in L2 LIM in machine mode and then load FIT
image u-boot.itb from SD card into RAM.
U-Boot SPL expects u-boot.itb FIT image at the starting of SD card sector
number (0x822) of GUID type "2E54B353-1271-4842-806F-E436D6AF6985"
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When building U-Boot we select the architecture via Kconfig and not ARCH
being passed in via the environment or make cmdline.
While in here, add the doc file to the MAINTAINERS entry.
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Amit Singh Tomar <amittomer25@gmail.com>
When building U-Boot we select the architecture via Kconfig and not ARCH
being passed in via the environment or make cmdline.
While in here, add the doc file to the MAINTAINERS entry.
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Anup Patel <anup.patel@wdc.com>
Cc: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
When building U-Boot we select the architecture via Kconfig and not ARCH
being passed in via the environment or make cmdline.
While in here, add the doc file to the MAINTAINERS entry for coldfire.
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Tom Rini <trini@konsulko.com>
When building U-Boot we select the architecture via Kconfig and not ARCH
being passed in via the environment or make cmdline.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
When building U-Boot we select the architecture via Kconfig and not ARCH
being passed in via the environment or make cmdline.
Cc: Adam Ford <aford173@gmail.com>
Cc: Vanessa Maegima <vanessa.maegima@nxp.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
- Fix mmc of path after syncfrom kernel dts;
- Add dwc3 host support with DM for rk3399;
- Add usb2phy and typec phy for rockchip platform;
- Migrate board list doc to rockchip.rst;
- Add rk3399 Pinebook Pro board support;
- Update dram_init in board_init and add memory node in SPL;
Since the commit 1289e96797 ("sandbox: spi: Drop command-line SPI
option"), "--spi_sf" command line option is no longer supported.
So update the following documents to sync them up with the change.
doc/arch/sandbox.rst
doc/SPI/README.sandbox-spi
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
As documentation is being moved to doc/boards/rockchip create a warning
message and remove the redundant list of supported boards.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update the list of supported boards with the information available
on doc/README.rockchip.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
As an additional step to move documentation to doc/boards/rockchip
improve format of the supported board list to make it more readable.
Additionally, add the configuration files used to build them based on
doc/README.rockchip.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Document eMMC partition creation and program steps for
rockchip platforms.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A the moment the FSP-S configuration is a mix of hard coded values and
devicetree properties.
This patch makes FSP-S full configurable from devicetree by
adding binding properties for all FSP-S parameters.
Co-developed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> (Tested on coral)
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
A the moment the FSP-M configuration is a mix of hard coded values and
devicetree properties.
This patch makes FSP-M full configurable from devicetree by adding
binding properties for all FSP-M parameters.
Co-developed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> (Tested on coral)
[sjg: Fix a build error for coral]
Signed-off-by: Simon Glass <sjg@chromium.org>
[bmeng: Add __maybe_unused to fsp_update_config_from_dtb()]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add the device firmware update functions to the generated HTML
documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
In dfu_alt_info for eMMC the eMMC partition number can be specified.
The separator in dfu_alt_info is a semicolon not a comma.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
If OP-TEE is compiled with an EDK2 application running in secure world
it can process and store UEFI variables in an RPMB.
Add documentation for the config options enabling this.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If "object=" is specified in "keydir" when using the pkcs11 engine do
not append another "object=<key-name-hint>". This makes it possible to
use object names other than the key name hint. These two string
identifiers are not necessarily equal.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Update stm32mp1 board documentation with new management of MMC and
MTD partitions and new PID df11.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
As the op-tee presence is detected by U-boot, the stm32mp15_optee_defconfig
is identical to stm32mp15_trusted_defconfig and can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This pull request comprises:
* bug fixes
* documentation fixes
* a new function to determine u16 string sizes and its unit test
-----BEGIN PGP SIGNATURE-----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=vqQZ
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc2-4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc2-4
This pull request comprises:
* bug fixes
* documentation fixes
* a new function to determine u16 string sizes and its unit test
Fix some typos, add information about setup_omap_atag, remove old suff
about ONENAND_SUPPORT and update guide for UBIFS.
Signed-off-by: Pali Rohár <pali@kernel.org>
Add the UEFI unit test helper functions to the generated HTML
documentation.
Correct some documentation texts in include/efi_selftest.h.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for configuring the CLK_25M pin as well as the RGMII I/O
voltage by the device tree.
By default the AT803x PHYs outputs the 25MHz clock of the XTAL input.
But this output can also be changed by software to other frequencies.
This commit introduces a generic way to configure this output.
Also the PHY supports different RGMII I/O voltages: 1.5V, 1.8V and 2.5V.
An internal LDO is able to provide 1.5V (default) and 1.8V. The 2.5V
option needs an external supply voltage. This commit adds support to
switch the internal LDO to 1.8V.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- dts clean up to use -u-boot for px30, rk3399 boards
- dts sycn from upstream kernel for rk3328, rk3399
- add rockchip rng driver
- new board support: rk3328-roc-cc, rk3399-roc-pc,Nanopi M4 2GB
Coreboot is a first-stage bootloader mostly used on x86 devices as an
alternative to UEFI. Coreboot runs in 32-bit mode.
U-Boot currently supports booting from coreboot as a second-stage
bootloader, also in 32-bit mode. However it is useful to be able to run
U-Boot in 64-bit mode. To do this we can have a 32-bit SPL which switches
over the CPU and jumps to a 64-bit U-Boot proper.
Add a new 'coreboot64' board for running 64-bit U-Boot from coreboot. This
uses binman to create an image with a 32-bit SPL and a 64-bit U-Boot.
This allows running 64-bit EFI images on x86, for example, without needing
a native U-Boot port for a board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
1. add the address mapping related properties;
2. make "ref" clock optional, and add optional clock "da_ref";
3. add the banks layout of TPHY V1 and V2;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
