Commit graph

7 commits

Author SHA1 Message Date
Mihai Sain
d2b4809bde configs: sama5d2: add qspi config for QSPI1
Add new config for storing environment from QSPI1.

Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
[eugen.hristev@microchip.com: cleanup and add MAINTAINERS entry]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2021-09-21 10:05:38 +03:00
Simon Glass
401d1c4f5d common: Drop asm/global_data.h from common header
Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-02 15:33:42 -05:00
Simon Glass
5255932f01 common: Move some board functions out of common.h
A number of board function belong in init.h with the others. Move them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:25:21 -05:00
Eugen Hristev
bc2d313d68 board: atmel: sama5d2_icp: enable green led on SPL completion
Enable the green led on SPL completion.
Red led has no pulldown and it will be lighted by default when the
board starts up.
If the PMIC is not configured to enable LDO2, the leds will not light.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-05-15 09:34:22 +03:00
Eugen Hristev
2950c514e8 board: atmel: sama5d2_icp: standby disable on CAN transceivers in SPL
The 2 CAN transceivers have a STBDY pin which must be low in order to
operate.
This pin is tied to PB25.
Set it to 0 in bootstrap.
At a later time, this needs to be controlled by Linux power management
system, or requested by some driver as a gpio and tied to 0 during
CAN link up.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-05-15 09:34:22 +03:00
Eugen Hristev
57fbd36c66 board: atmel: sama5d2_icp: add periph reset in SPL hw init
Some periphs on the board need to be reset by holding their reset GPIO down
for a specific time period.
On a warm reset, the periphs are not being reset by any reset pin and may be
in a wrong state.
Reset them in the SPL to make sure we are booting into the correct state
machine of the specific board periphs (KSZ eth switch, USB hub, HSIC eth,
Ethercat)

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-05-15 09:34:22 +03:00
Eugen Hristev
f085452d85 board: atmel: add SAMA5D2 ICP board
The SAMA5D2 ICP Board features the SAMA5D27 SoC,
together with QSPI Flash, Wilc3000 wireless device and
EtherCat support.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-04-18 09:43:22 +03:00