Overriding fastboot_set_reboot_flag() in arch/arm/mach-omap2/boot-common.c
leaves it applying all boards that derive from this, not just the ones which
have support for Android bootloader flow. Move the weak function override to
the relevant board files.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
Since DRA7xx/AM57xx SR1.1 and SR1.0 has errata to limit the frequency of
MMC1 to 96MHz and frequency of MMC2 to 48MHz for AM572x SR1.1, limit the
frequency and disable higher speed modes for those revision.
Also use the recommended IO delays (those tagged with "rev11")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
board_usb_init()/_cleanup() should be in board files and don't have
a place in the xhci-omap driver. Weak versions for
board_usb_init()/_cleanup() already exist in common/usb.c
(for host mode) and drivers/usb/gadget/g_dnl.c (for gadget mode).
Therefore, remove init and cleanup functions from xhci-omap and
implement them in the board files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update the board pinmux for AM574x-IDK board using latest PMT[1] and the
board files named am574x_idk_v1p3b_sr2p0 that were auto generated on
13th October, 2017 by "Ahmad Rashed <a-rashed@ti.com>".
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM574x-idk has the following DDR parts attached:
EMIF1: MT41K256M16HA (1GB with ECC)
EMIF2: MT41K256M16HA (1GB without ECC)
Enabling 2GB DDR without interleaving between EMIFs. And
enabling ECC on EMIF1.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
Add support for selecting proper dtb for
am57xx BeagleBoard X15 revC u-boot from FIT
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
AM571x supports DDR running at 666MHz. Right now it is
clocked at 532MHz which is lower than what is supported.
In order to have maximum performance on AM571-IDK,
switch DDR to 666MHz.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We are now using an env_ prefix for environment functions. Rename these
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
This is a strange name for a function that loads the environment. There is
now only one implementation of this function, so use the new env_load()
function directly instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
BeagleBoard X15 revC board is similar to X15 revB1 except
with a SR2.0 where revB1 uses a SR1.1. Add board detection
support for revC.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
board_is*("rev", board_ti_get_rev()) uses strncmp() for
revison detection and assumes it is success if return value
is <= 0. This will fail in case of multiple versions, as
revb will be true for board_is_*revb() and board_is_*reva().
Fix it by looking for exact match of the string.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
One can obtain those variables using next commands:
$ fastboot getvar cpu
$ fastboot getvar secure
$ fastboot getvar board_rev
$ fastboot getvar userdata_size
Those variables are needed for fastboot.sh script.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the board pinmux for AM572x-evm using latest PMT[1] and the
board files named am572x_gp_evm_A3a_sr2p0 and am572x_gp_evm_A2b_sr1p1
that were autogenerated on 30th January, 2017 by
"Ahmad Rashed <a-rashed@ti.com>" and "Tom Johnson <thjohnson@ti.com>".
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update the board pinmux for AM571x-IDK board using latest PMT[1] and the
board files named am571x_idk_v1p3b_sr2p0 that were autogenerated on
23rd March, 2017 by "Ahmad Rashed <a-rashed@ti.com>" and
"Tom Johnson <thjohnson@ti.com>".
[1] https://dev.ti.com/pinmux/app.html#/default/
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update the board pinmux for AM572x-IDK board using latest PMT[1] and the
board files named am572x_idk_v1p3b_sr2p0 that were autogenerated on
30th January, 2017 by "Ahmad Rashed <a-rashed@ti.com>" and
"Tom Johnson <thjohnson@ti.com>".
[1] https://dev.ti.com/pinmux/app.html#/default/
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Now CONFIG_GENERIC_MMC and CONFIG_MMC match for all defconfig.
We do not need two options for the same feature. Deprecate the
former.
This commit was generated with the sed script 's/GENERIC_MMC/MMC/'
and manual fixup of drivers/mmc/Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
A weak version of the function board_usb_init is implemented in:
common/usb.c
drivers/usb/host/xhci-omap.c
To fix the double implementations:
* Convert the board_usb_init function in drivers/usb/host/xhci-omap.c
normal (not weak).
* The function board_usb_init in drivers/usb/host/xhci-omap.c calls to
the weak function omap_xhci_board_usb_init.
* Rename board version of the function board_usb_init to
omap_xhci_board_usb_init.
Done only for boards that defines CONFIG_USB_XHCI_OMAP.
To achieve the same flexibility with the function board_usb_cleanup:
* Add a normal (not weak) implementation of the function
board_usb_cleanup in drivers/usb/host/xhci-omap.c
* The function board_usb_cleanup in drivers/usb/host/xhci-omap.c calls
to the weak function omap_xhci_board_usb_cleanup.
* Rename board version of the function board_usb_cleanup to
omap_xhci_board_usb_cleanup.
Done only for boards that defines CONFIG_USB_XHCI_OMAP.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
As per the latest pinmux data available for AM572x EVM,
rev A3, input should be enabled on MMC clock lines for
MMC2/2/3 for stable operation.
Further, AM572x TRM, SPRUHZ6, Revised June 2016, in
section 18.4.6.1.1 "Pad Configuration Registers" states
that input should be enabled for MMC 2/3/4 clock lines.
Enable input on MMC1 and MMC3 clock to match the latest
pinmux data. Input is already enabled on MMC2 clock for
BeagleBoard x15. Further, input is already enabled on all
MMCx clocks for other AM57xx boards (AM572x and AM571x
IDK).
Tested with HS and UHS SD card on AM572x EVM Rev A3.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
AM571x IDK and AM572x IDK have optional LCD Kits that can be purchased.
These can be one of OSD101T2045 or the newer OSD101T2587. The LCD panel
itself has no registers that can be used to identify the panel, however,
the touchscreen controllers on the panels are different.
Hence to ease user experience, we can use the touch screen controller's
ID information to detect what kind of panel we use and select the
appropriate kernel dtb for the platform configuration.
NOTE: AM572x IDK default configuration is for LCD Connectivity, however
the AM571x IDK has a jumper (J51) that needs to be mounted for the IDK
to operate with LCD (Vs two PRUSS ethernet port option).
Touchscreen ID information is documented in:
http://www.osddisplays.com/TI/OSD101T2587-53TS_A.1.pdf
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use the same convention that was used for ICSS1 Ethernet
- If pin is output, set as PIN_OUTPUT
- If pin is input and external pull resistor present set as PIN_INPUT
- If pin is input and external pull resistor absent, set pull to same
as that of the external PHY's internall pull.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The board can support either ICSS1 Ethernet ports or LCD
based on J51 jumper. Factory default is ICSS1 Ethernet ports
(i.e. Jumper not populated).
Use the GPIO to detect the jumper setting and configure the
pinmux accordingly. Also select the right DT blob based on
the chosen configuration.
J51 absent -> ICSS1 Ethernet, no LCD on VOUT -> am571x-idk.dtb
J51 present -> LCD on VOUT, no ICSS1 Ethernet -> am571x-idk-lcd-osd.dtb
At present we only support the assume it is the Legacy LCD.
LCD detection mechanism needs to be added later to differentiate
between legacy vs new LCD.
For ICSS1 Ethernet pins use the following convention to set the pinmux
as PMT data is not yet finalized.
- If pin is output, set as PIN_OUTPUT
- If pin is input and external pull resistor present set as PIN_INPUT
- If pin is input and external pull resistor absent, set pull to same
as that of the external PHY's internall pull.
- Do not use SLEW_CONTROLon any pin.
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
To keep a consistent MMC device mapping in SPL and in u-boot, let's
register the MMC controllers the same way in u-boot and in the SPL.
In terms of boot time, it doesn't hurt to register more controllers than
needed because the MMC device is initialized only prior being accessed for
the first time.
Having the same device mapping in SPL and u-boot allows us to use the
environment in SPL whatever the MMC boot device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
serial# variable is used to correctly display device ID in
"fastboot devices". It also can be used further for displaying device ID
in "adb devices" (should be passed as "androidboot.serialno" to kernel
cmdline, via "bootargs" variable).
Serial number generating algorithm is described at [1].
[1] http://lists.denx.de/pipermail/u-boot/2015-March/207462.html
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The GPIO7 pad mux should be programmed to POWERHOLD value
as per board design. In cases where the PMIC is shut off the
mux is set to GPIO7 mode. So during initialization to be on the
safer side set the mode to POWERHOLD.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The AM571x Industrial Development Kit (IDK) is a board based on TI's
AM571x SoC which has a single core 1.5GHz Cortex-A15processor. This
board is a development platform for the Industrial Market with:
- 1GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector
The PRU/ICSS will be supported by 3rd party software for EtherCat,
Profibus, and other Industrial protocols.
The link to the data sheet and TRM can be found here:
http://www.ti.com/product/AM5718
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the board pinmux for AM572x-IDK board using latest PMT[1] and the
board files named am572x_idk_v1p3b_sr2p0 that were autogenerated on
20th October, 2016 by "Steve Kipisz <s-kipisz2@ti.com>" and
"Tom Johnson <thjohnson@ti.com>".
[1] https://dev.ti.com/pinmux/app.html#/default/
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the board pinmux for AM572x-IDK board using latest PMT[1] and the
board files named am572x_gp_evm_A3a_sr2p0 that were autogenerated on
19th October, 2016 by "Ahmad Rashed<a-rashed@ti.com>".
[1] https://dev.ti.com/pinmux/app.html#/default/
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the timing for RGMII0 interface based on
PCT_DRA75x_DRA74x_SR1.1_v1.3.10 version (Jan 2016). This update
is for SR1.1
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
BeagleBoard-X15 Rev B1 with SR1.1 platform have incompatible changes for HDMI
GPIO requiring new dtb support. This implies we have to properly identify
the platform now as well. Hence provide a different board name for the
Rev B1 variants.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
AM57xx evm Rev A3 with SR2.0 platform have incompatible changes for HDMI
GPIO requiring new dtb support. This implies we have to properly identify
the platform now as well. Hence provide a different board name for the
Rev A3 variations.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It can be expected that different paper spins of a SoC can have
different definitions for OPP and can have their own constraints
on the boot up OPP for each voltage rail. In order to have this
flexibility, add support for dynamically selecting the OPP voltage
based on the board to handle any such exceptions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Populate the corresponding TEE image processing call to be
performed during FIT loadable processing.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Verification has to be done before booting any images on HS devices. So
default the boot to FIT on HS devices.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Starting with the changes to fix USB host on am57xx/am43xx we stopped
using usb_otg_ss1/related stuff and but we hadn't been enabling the
relevant options to cause the warnings until just recently.
Fixes: 55efadde7e (ARM: AM57xx: AM43xx: Fix USB host)
Fixes: a48d687c57 (configs: am57xx: Enable download gadget)
Signed-off-by: Tom Rini <trini@konsulko.com>
When beagleboard-X15 is booted, we see the following log:
Unidentified board claims BBRDX15_ in eeprom header
This is because of the missing check for x15 (the default) and reports
an error for a valid board configuration. Fix the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Felipe Balbi has move on from TI and the current email ID is no longer
valid. So, replacing with Lokesh.
While at it, update missing config file which was untracked.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Modify the SPL build procedure for AM57xx and DRA7xx high-security (HS)
device variants to create a secure u-boot_HS.img FIT blob that contains
U-Boot and DTB artifacts signed with a TI-specific process based on the
CONFIG_TI_SECURE_DEVICE config option and the externally-provided image
signing tool.
Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
FIT allows for a multiple dtb in a single image. SPL needs away to
detect the right dtb to be used. Adding support for the same for am57xx
platforms.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
