- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
In Errata 1.0.24, if the board is running at OPP50 and has a warm reset,
the boot ROM sets the frequencies for OPP100. This patch attempts to
drop the frequencies back to OPP50 as soon as possible in the SPL. Then
later the voltages and frequencies up set higher.
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Adapt to current framework]
Signed-off-by: Tom Rini <trini@ti.com>
Add a am33xx_spl_board_init (and enable the PMICs) that we may see,
depending on the board we are running on. In all cases, we see if we
can rely on the efuse_sma register to tell us the maximum speed. In the
case of Beaglebone White, we need to make sure we are on AC power, and
are on later than rev A1, and then we can ramp up to the PG1.0 maximum
of 720Mhz. In the case of Beaglebone Black, we are either on PG2.0 that
supports 1GHz or PG2.1. As PG2.0 may or may not have efuse_sma set, we
cannot rely on this probe. In the case of the GP EVM, EVM SK and IDK we
need to rely on the efuse_sma if we are on PG2.1, and the defaults for
PG1.0/2.0.
Signed-off-by: Tom Rini <trini@ti.com>
We defined PHYS_DRAM_1 to 0x80000000 (start of DRAM) and then used this
for CONFIG_SYS_SDRAM_BASE. But then we kept on referencing PHYS_DRAM_1
in other places. Change to directly setting CONFIG_SYS_DRAM_BASE and
then using that name in code.
Signed-off-by: Tom Rini <trini@ti.com>
s_init has the same outline for all the AM33xx based
board. So making it generic.
This also helps in addition of new Soc with minimal changes.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Cleaning up the clocks layer.
This helps in addition of new Soc with minimal
changes.
This is derived from OMAP4 boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Locking sequence for all the dplls is same.
In the current code same sequence is done repeatedly
for each dpll. Instead have a generic function
for locking dplls and pass dpll data to that function.
This is derived from OMAP4 boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
NOR requires that s_init be within the first 4KiB of the image so that
we can perform the rest of the required pinmuxing to talk with the rest
of NOR that we are found on. When NOR_BOOT is set we save our
environment in NOR at 512KiB and a redundant copy at 768KiB. We avoid
using SPL for this case and u-boot.bin is written directly to the start
of NOR.
We enclose the DMM-related parts of arch/arm/cpu/armv7/am33xx/emif4.c
with TI81xx checks as at this time U-Boot does not discard unused
sections in the main build and this code relies on functions specific to
(and only provided in) ti81xx-related code.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds support for the NOR module that attaches
to the memory cape for a Beaglebone board. This does not
add booting support; only support so that you can boot from
SD/MMC and see the NOR module so that it can be programmed.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Clean up config changes slightly]
Signed-off-by: Tom Rini <trini@ti.com>
We rework the various board_is_foo() checks to take a pointer to
struct am335x_baseboard_id rather than using a local copy in board.c.
This allows us to make use of the same checks in mux.c as well as fixing
problems when this code could be running from read-only memory.
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
BD ram address may vary in various SOC, so removing the hardcoding and
passing the same information through platform data
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
move uart soft reset code to common place and call
this function from board code, instead of copy and paste
this code for every board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
[trini: Fix igep0033 build, remove 'regval' on pcm051]
Signed-off-by: Tom Rini <trini@ti.com>
move rtc32k_enable() to common place so all am33xx boards can use it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR
Conflicts:
arch/arm/include/asm/arch-omap5/omap.h
Signed-off-by: Tom Rini <trini@ti.com>
Jump into full u-boot mode if a 'c' character is received on the uart.
We need to adjust the spl bss/malloc area to not overlap with the
loadaddr of the kernel (sdram + 32k), so move it past u-boot instead.
For raw mmc, we store the kernel parameter area in the free space after
the MBR (if used). For nand, we use the last sector of the partition
reserved for u-boot.
This also enables the spl command in the full u-boot so the kernel
parameter area snapshot can be created.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
We need to call the save_omap_boot_params function on am33xx/ti81xx and
other newer TI SoCs, so move the function to boot-common. Only OMAP4+
has the omap_hw_init_context function so add ifdefs to not call it on
am33xx/ti81xx. Call save_omap_boot_params from s_init on am33xx/ti81xx
boards.
Reviewed-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
After further testing we can run DDR at 400MHz so update the timings
again.
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tom Rini <trini@ti.com>
The AM33xx emif4/ddr support closely matches what is need to support
TI814x except that TI814x has two EMIF instances. Refactor all the
emif4 helper calls and the config_ddr() init function to use an
additional instance number argument.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Eliminate AM33xx specific names to prepare for TI814x support
within AM33xx-land.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Enable DDR PHY dynamic power down bit, which enables
powering down the IO receiver when not performing read.
This also helps in reducing overall power consumption in
low power states (suspend/standby).
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
We add USB (RNDIS gadget) SPL support as a separate target. We need to
pull out YMODEM support in order to be a small enough target binary.
Signed-off-by: Tom Rini <trini@ti.com>
This adds necessary config options and a new build target,
am335x_evm_usbspl, to enable usb booting and fixes board_eth_init()
function to take into account that we may have USB ether support in SPL
now. This uses the same MAC for both cpsw and USB, in order to match
ROM behavior.
The usbspl build target does not contain UART SPL, CPSW SPL or extra
environment settings, so that we may fit within our binary size
constraint.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Signed-off-by: Tom Rini <trini@ti.com>
In commit cfd4ff6 we implemented part of advisory 1.0.10 (internal delay
for RGMII mode not supported). This in turn however requires that we
set the tx clock delay feature in the PHY itself.
Signed-off-by: Tom Rini <trini@ti.com>
AM335x EVM 1.5A uses Micron MT41J512M8RH-125 SDRAM 4Gb (512Mx8) as the
DDR3 chip.
[Hebbar Gururaja <gururaja.hebbar@ti.com>]
- Resolve merge conflict while rebasing. File structure is
changed in the mainline. So re-arrange the code accordingly.
- Update commit message to reflect the DDR3 part number
Signed-off-by: Jeff Lance <j-lance1@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
When ethaddr is not set in environment the MAC address is read
from efuse. The message was only printed in debug case, but this
message could be of interest for the ordinary user, so printf it.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
According to errata the AM335x device does not support internal delay
mode, so RGMII1_IDMODE and RGMII2_IDMODE must be set to 1.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
We add CONFIG_ENV_VARS_UBOOT_CONFIG,
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and CONFIG_BOARD_LATE_INIT to set
the variables and then fdtfile and findfdt to make us of this. It is
now possible to do 'run findfdt' to have fdtfile be set to the value of
the dtb file to load for the board we are running on.
Signed-off-by: Tom Rini <trini@ti.com>
This patch extends the am335x_evm board for the AM335x IDK.
The IDK board uses MII for the ethernet phy (same as
Beaglebone board) and MMC0 for storage (but without
card detect line).
The IDK uses UART3 for console. So u-boot must be build
with CONFIG_SERIAL4 and CONFIG_CONS_INDEX=4 or for
the am335x_evm_uart3 board configuration as introduced
by Andrew Bradfords recent patch series "am33xx: Enable
UART {1,2,3,4,5}...". When using the IDK with console on UART0,
those patches are not required. In this case the board
slightly needs to be modified.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
If configured to use UART{1,2,3,4,5} such as on the Beaglebone RS232
cape or on the am335x_evm daughterboard, enable the proper pin-muxing.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
Move the hardcoded ddr2/ddr3 settings for the ti boards to board code,
so other boards can use different types/timings.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make apply with rtc32k_enable() in the file]
Signed-off-by: Tom Rini <trini@ti.com>
The i2c header is specific to ti(-derived) boards, and not generic for all
am335x boards.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make re-apply with rtc32k_enable() applied]
Signed-off-by: Tom Rini <trini@ti.com>