Size grew a bit so nand-spl didn't fit in 4k, reduce done by removing
LAW entries not needed during SPL phase.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
ctrl_regs.c: In function 'set_ddr_sdram_cfg_2':
ctrl_regs.c:641:15: warning: variable 'rcw_en' set but not used [-Wunused-but-set-variable]
ctrl_regs.c: In function 'compute_fsl_memctl_config_regs':
ctrl_regs.c:951:31: warning: array subscript is above array bounds [-Warray-bounds]
ctrl_regs.c:752:34: warning: array subscript is above array bounds [-Warray-bounds]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
fsl_corenet_serdes.c: In function 'fsl_serdes_init':
fsl_corenet_serdes.c:511:8: warning: variable 'buf' set but not used [-Wunused-but-set-variable]
fsl_corenet_serdes.c:498:18: warning: variable 'lane_prtcl' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
options.c: In function 'populate_memctl_options':
options.c:486:28: warning: variable 'pdodt' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
uec.c: In function 'uec_stop':
uec.c:267:22: warning: variable 'uccf' set but not used [-Wunused-but-set-variable]
uec.c: In function 'uec_set_mac_if_mode':
uec.c:328:15: warning: variable 'uec_info' set but not used [-Wunused-but-set-variable]
uec.c: In function 'adjust_link':
uec.c:519:11: warning: variable 'uec_regs' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
ehci-fsl.c: In function 'ehci_hcd_init':
ehci-fsl.c:43:7: warning: variable 'usb_phy' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
fm.c: In function 'fm_init_common':
fm.c:398:6: warning: variable 'n' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
sbc8560.c: In function 'ft_board_setup':
sbc8560.c:351:12: warning: variable 'tmp' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
sbc8548.c: In function 'local_bus_init':
sbc8548.c:80:7: warning: variable 'lbc_hz' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mpc8569mds.c: In function 'local_bus_init':
mpc8569mds.c:306:7: warning: variable 'lbc_hz' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
mpc8568mds.c: In function 'local_bus_init':
mpc8568mds.c:150:7: warning: variable 'lbc_hz' set but not used [-Wunused-but-set-variable]
mpc8568mds.c: In function 'pib_init':
mpc8568mds.c:271:11: warning: variable 'orig_i2c_bus' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
mpc8548cds.c: In function 'local_bus_init':
mpc8548cds.c:87:7: warning: variable 'lbc_hz' set but not used [-Wunused-but-set-variable]
mpc8548cds.c: In function 'lbc_sdram_init':
mpc8548cds.c:121:7: warning: variable 'cpu_board_rev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
pixis.c: In function 'strfractoint':
pixis.c:383:6: warning: variable 'intarr_len' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
cds_pci_ft.c: In function 'cds_pci_fixup':
cds_pci_ft.c:31:12: warning: variable 'tmp' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
fsl_lbc.c: In function 'upmconfig':
fsl_lbc.c:110:9: warning: variable 'mdr' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
tlb.c: In function 'disable_tlb':
tlb.c:175:34: warning: variable '_mas7' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
cpu_init.c: In function 'cpu_init_r':
cpu_init.c:320:7: warning: variable 'l2srbar' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable AR8021 as it used on Freescale boards: P1020RDB-PC, P1021RDB-PC,
P2020RDB-PC, P1020UTM-PC, and P1020MSBG-PC.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In order to support 1920x01080 resolution, we must increase the alloc
length.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Anatolij Gustschin <agust@denx.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For ICS307-02, there is one general expression to generate SYSCLK:
CLK1Frequency = InputFrequency * 2 * (VDW + 8) / ((RDW + 2) * OD)
If we want the required frequency for SYSCLK, we must find one solution
to generate this frequency, this solution includes VDW, RDW and OD.
For OD, there are only eight option value: 10, 2, 8, 4, 5, 7, 3, 6.
For RDW, the range is 1 to 127.
For VDW, the range is 4 to 511.
First, we use one OD, RDW and required SYSCLK to calculate the VDW,
if VDW is in it's range, we will calculate the CLK1Frequency with
the OD, RDW and VDW calculated, and we will check this percent
(CLK1Frequency / required SYSCLK), and the precision is 1/1000.
if the percent is less than 1/1000, we think the CLK1Frequency is we want.
Otherwise, We will continue to calculate it with the next OD and RDW.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
m28evk has one bank of RAM.
Fix the comment.
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
GPR register definition is already available at imx-regs.h, so remove the duplication.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This enables the second port, aka. the port with the USB connector on the
M28EVK.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
This driver supports both EHCI ports on the i.MX28 CPU.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
This code allows the DDR DRAM size to be detected at runtime. The RAM size is
stored into two scratch registers, from which it is then fetched in U-Boot.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
This patch introduces proper ARM vector handling for i.MX28 CPU. This issue
wasn't addressed because the interrupts weren't enabled on any ARMv5 core,
therefore the issue wasn't noticed earlier.
In previous implementation, the vectoring code used by i.MX28 CPU when an
exception happened was that of the SPL. With this change, the branch target when
an exception happens can be reconfigured by U-Boot.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
This patch adds SPL code for the M28 board.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
This contains support for the following components:
- DUART
- MMC
- Both FEC interfaces
- NAND
- I2C (RTC, EEPROM)
- SPI (FLASH)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
This tool can now generate proper image for "BootStream" files.
NOTE: This tool now works only for NAND.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Taken from Linux kernel with minor modifications:
commit bf985969e27b507f734435a99df8bf745a3dbb2b
Author: Shawn Guo <shawn.guo@freescale.com>
Date: Mon Dec 20 22:57:43 2010 +0800
ARM: mxs: Add iomux support
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Acked-by: Andy Fleming <afleming@gmail.com>
Fix:
zmx25.c: In function 'board_late_init':
zmx25.c:131:25: warning: variable 'padctl' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefano Babic <sbabic@denx.de>
Fix:
mx3fb.c: In function 'video_hw_init':
mx3fb.c:827:30: warning: variable 'vesa_idx' set but not used
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
When the resolution is set to 800x600 and 1024x768,
but, the driver will use 1280x1024 resolution to set the DIU register
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
add new configuration file da850_am18xxevm.h for AM18xx boards
which are based on da850 SOC. AM18xx has WINBOND spi flash which
is indicated in the config file. And make appropriate changes in
board.cfg for building.
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This is needed to support the latest kernel versions.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
