The QEMU/mach-virt targeted port of u-boot currently only runs on
QEMU under TCG emulation, which does not model the caches at all,
and so no users can exist that are relying on the GRUB hack for
EFI boot.
We will shortly enable support for running under KVM, but the GRUB
hack (which disables all caches without doing cache cleaning by VA
during ExitBootServices()) is likely to cause more problems than it
solves, given that KVM hosts require correct maintenance if they
incorporate non-architected system caches.
So let's disable the GRUB hack by default on the QEMU/mach-virt
port.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
QEMU's mach-virt machine only supports selecting CPU models that
implement the virtualization extensions, and are therefore guaranteed
to support LPAE as well.
Initially, QEMU would not allow emulating these CPUs running in HYP
mode (or EL2, for AArch64), but today, it also contains a complete
implementation of the virtualization extensions themselves.
This means we could be running U-Boot in HYP mode, in which case the
LPAE long descriptor page table format is the only format that is
supported. If we are not running in HYP mode, we can use either.
So let's enable CONFIG_ARMV7_LPAE for qemu_arm_defconfig so that we
get the best support for running with the MMU and caches enabled at
any privilege level.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Done with:
./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS
./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS -H
Signed-off-by: Peng Fan <peng.fan@nxp.com>
[trini: A few more migrations]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_NAND_DRIVERS
CONFIG_SPL_NAND_ECC
CONFIG_SPL_NAND_SIMPLE
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
cleanups
- fsl-crypto: RNG support and bug fixes
Restore CONFIG_ENV_ADDR value to fix boot hang with IFC-NOR
which is default boot source.
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add Root Complex and Endpoint mode specific config entries, such that
it's feasible to enable the RC and/or EP mode driver indepently.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable support for sub command 'env info' in sandbox
with CONFIG_CMD_NVEDIT_INFO. This is aimed primarily
at adding unit test.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC
driver can be used for SoC detection.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC
driver can be used for SoC detection.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Add a sandbox SOC driver, and some tests for the SOC uclass.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The Beacon EmbeddedWorks kit is based on the R8A774A1 SoC also
known as the RZ/G2M.
The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add Kconfig entries for the dc2114x driver and convert various boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
- Fix SiFive HiFive Unleashed board booting failure problem.
- Enable SiFive fu540 PWM driver.
- Support SiFive fu540: SPI boot.
- Update OpenSBI used for RISC-V CI testing.
- Revert "riscv: Allow use of reset drivers".
- Revert "Revert "riscv: sifive: fu540: Add gpio-restart support"".
- sysreset: syscon:
- Don't assume default value for offset and mask property.
- Support value property.
- qemu: Add syscon reboot and poweroff support.
- Fix SIFIVE debug serial dependency.
- Fix linking error when building u-boot-spl with no SMP support.
- AE350 use fdtdec_get_addr_size_auto_noparent to parse smc reg.
- Make memory node available to SPL in hifive-unleashed-a00-u-boot.dtsi
- SiFive fu540 avoid using hardcoded ram base and size.
Add booting from SPI for SiFive Unleashed board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
- New rk3326 board: Hardkernel Odroid Go2;
- Update board config and dts for RockPI 4/N8/N10;
- Update led boot on support for roc-rk3399-pc;
- Enable SPI Flash suppor for rk3328 rock64 board;
- Update rockchip pcie phy to use generic framework;
Disable ram rockchip debug driver for ROCKPi N8/N10 boards
since we have verified ram in many instances with respective
U-Boot versions.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable PCI/NVME for M.2 Slot on RockPI-4 boards.
=> nvme info
Device 0: Vendor: 0x144d Rev: 4L1QCXB7 Prod: S35FNX0J623292
Type: Hard Disk
Capacity: 122104.3 MB = 119.2 GB (250069680 x 512)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable common on board devices for ROCKPi N8.
- USB 2.0 Host
- USB 2.0 OTG/Gadget
- HDMI Out
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable common on board devices for ROCKPi N10.
- USB 2.0 Host
- USB 3.0 Host
- USB 3.0 Gadget
- HDMI Out
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ROC-RK3399-PC has specific set of configurations for
on-board led setup.
Due to easiness for user to know the state of the board
roc-rk339-pc board code will setup the low power led
on/off, and waiting for user to press power key and then
glow full power led.
All this needs to happen only during power-on-reset not
for soft reset or WDT.
Also, it is not a proper usage to ask the user to press
the Power key if the board connected remotely, so add
the environment variable 'pwr_key' to check as well.
So, user need to press Power key only
- during POR
- pwr_key=y
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
roc-rk3399-pc has some specific requirements to support LEDS,
environment. board detection and etc prior to U-Boot proper.
So as of now SPL would be a better stage for these custom board
requirements to support unlike TPL. Adding few of these custom
requirements like LEDS in TPL would require extra code pulling
and also the size of TPL can grow.
So, this patch moves the leds code from TPL into SPL Board init
led_setup code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(split tpl.c change as separate patch)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enabled
GPIO pin change compared to 4B, 4C.
So, add or enable difference nodes/properties in 4C dts
by including common dtsi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rock PI 4 has 3 variants of hardware platforms called
RockPI 4A, 4B, and 4C.
- Rock PI 4A has no Wif/BT.
- Rock PI 4B has AP6256 Wifi/BT, PoE.
- Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enable
GPIO pin change compared to 4B, 4C
So move common nodes, properties into dtsi file and include
on respective variant dts files.
Use 4B dts into default rock-pi-4 defconfig until we find any
solution for dynamic detection of these variants.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To fix below build error:
drivers/usb/host/built-in.o: In function `xhci_dwc3_remove':
drivers/usb/host/xhci-dwc3.c:174: undefined reference to `dwc3_shutdown_phy'
drivers/usb/host/built-in.o: In function `xhci_dwc3_probe':
drivers/usb/host/xhci-dwc3.c:130: undefined reference to `dwc3_setup_phy'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Disable ram rockchip debug driver for roc-rk3399-pc
boards since we have verified ram in many instances
with respective U-Boot versions.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot SPI Flash support for the PINE64 Rock64 board
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Adjust the ENV offset, size to fit into all images
on 16MB flash.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable DWC3 core, gadget for roc-rk3399-pc board.
This would help to use fastboot by default.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable config options to get HDMI output on RockPI-4 boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB gadget for rock-pi-4 boards.
This would help to use fastboot by default.
Note: Connect the Host USB cable (Port A or C) to rock-pi-4
Upper USB 3.0 port.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable PCI/NVME for M.2 Slot on RockPI-4 boards.
=> nvme info
Device 0: Vendor: 0x144d Rev: 2B2QEXM7 Prod: S4EUNG0MC10012Y
Type: Hard Disk
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Cc: Tom Cubie <tom@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB3.0 Host support for RockPI-4 boards.
Note that the Upper USB3.0 port is marked as otg and
lower USB3.0 port marked as host, so this below log
capture when USB3.0 mass storage plug in at lower
USB 3.0 port.
Log:
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (5 Gb/s, 0mA)
U-Boot XHCI Host Controller
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 224mA)
SanDisk Dual Drive 040130e3ee554b7078843f4eb331646
Cc: Tom Cubie <tom@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB3.0 Host support for RockPro64 boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
