At present some Rockchip SoCs and boards are not mentioned in the README.
So that people can see which SoCs are supported, expand the list to
include everything.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both
obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be
used to control the build in both SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This add device tree binding documentation for the MSCC serial GPIO
driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microsemi.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Switching private data manual allocation to driver model auto allocation
so users no longer need to deallocate themself because this would be
deallocated by driver model when the device is no longer required.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- v2019.04 for no dm conversion drivers
- v2019.07 for partially converted drivers.
Note: there were many updates on this deadline, so better
not update this again.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Two variants of controllers are supported:
V1 (bitwise only) found in
i.MX21, i.MX27, i.MX31, i.MX51
V2 (byte operations) found in
i.MX25, i.MX35, i.MX50, i.MX53
Only tested on i.MX53 hardware but in both modes
(by modifying the device tree).
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
U-Boot supports using TrueType fonts on the console, which is useful for
presenting a nice UI to users, e.g. for system recovery.
Add information about how to compile this on ARM platforms, since this is
not obvious.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rename ax25-ae350 as ae350_rv[32|64] for 32 or 64 bit.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The function part_init() will only be built when we have both
CONFIG_PARTITIONS and CONFIG_HAVE_BLOCK_DEVICE set. Protect the call to
this function with both of these tests now.
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Vanessa Maegima <vanessa.maegima@nxp.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently on qemu-arm platforms environment is kept in RAM. Instead
use pflash device 1 to provide persistent environment support across
device reset.
Also (optionally) provide support for persistent environment across
qemu machine OFF/ON using following instructions:
- Create envstore.img using qemu-img:
qemu-img create -f raw envstore.img 64M
- Add a pflash drive parameter to the command line:
-drive if=pflash,format=raw,index=1,file=envstore.img
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcDiw9AAoJECaAFcEOcohNEa8H/RBWLbVQjHPXf6EjchXgVcSs
Gc+g2QmKZbN21XebfzBpCuZj62NROTWUcrPtor17yEBiMM1xPfe1vC7qtbkR6USj
VTt1JHeyGx3XafkkUpeps382YPfuaNqtabjwZaXlmeE4/VLbXQPE7x4tC4fdWus4
9K3OGQgRNFirn+RIZ7dQWtCby82PEC3cHkPc/n82cVHofcDsgKYK9mPpfcCn/gWF
A4Fa9cx4pjeaMrBHKjcByCiFmwYBPc97Hqzz64oHOdQP0g3h04ko+2w5DdwdeHVV
jKNcvkHESF4m1RGjrTbLEhy1f5UuOfcA1ise/cDX4pjXlBdwxHmvqT5vsE0MQzI=
=5sHL
-----END PGP SIGNATURE-----
Merge tag 'for-master-20181210' of git://git.denx.de/u-boot-rockchip
Improvements:
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
This adds a driver for the FAN53555 family of regulators and wraps it
in a PMIC implementation.
While these devices support a 'normal' and 'suspend' mode (controlled
via an external pin) to switch between two programmable voltages, this
incarnation of the driver assumes that the device is always operating
in 'normal' mode.
Only setting/reading the programmed voltage is supported at this time
and the following device functionality remains unsupported:
- switching the selected voltage (via a GPIO)
- disabling the voltage output via software-control
This matches the functionality of the Linux driver.
Tested on a RK3399-Q7 (with 'option 5' devices): setting voltages from
the U-Boot shell and verifying output voltages on the board.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The original bootcount methods do not provide an interface to DM and
rely on a static configuration for I2C devices (e.g. bus, chip-addr,
etc. are configured through defines statically). On a modern system
that exposes multiple devices in a DTS-configurable way, this is less
than optimal and a interface to DM-based devices will be desirable.
This adds a simple driver that is DM-aware and configurable via DTS.
If ambiguous (i.e. multiple bootcount-devices are present) the
/chosen/u-boot,bootcount-device property can be used to select one
bootcount device.
Initially, this provides support for the following DM devices:
* RTC devices
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
In some cases it may be useful to be able to change the fdt we have been
using and use another one instead. For example, the TI platforms uses an
EEPROM to store board information and, based on the type of board,
different dtbs are used by the SPL. When DM_I2C is used, a first dtb must
be used before the I2C is initialized and only then the final dtb can be
selected.
To speed up the process and reduce memory usage, introduce a new function
fdtdec_setup_best_match() that re-use the DTBs loaded in memory by
fdtdec_setup() to select the best match.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The biggest part of migration to using CONFIG_BLK is that we need to
have the various subsystems migrated first, so reword the plan here to
reference the new deadlines.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
As the core of the subsystem has been converted along with some of the
drivers, formalize a deadline for migration.
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Soeren Moch <smoch@web.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
As much of the USB system has been migrated to DM now, formalize a
deadline for migration.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Given that at this point the MMC subsystem itself has been migrated
along with a number of subsystem drivers, formalize a deadline for
migration.
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6o9t
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-12-03
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
Provide settings for Open-iSCSI
Reformat headers. h3-headers marked with ^^^ are not recognized in some
markup editors. Use the ### notation instead.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Linux uses "cdns,qspi-nor" as compatible string for the cadence
qspi driver, so change driver, docs and all device trees.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add a few notes on how to try out the MediaTek support so far.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
spi_init used in some areas in tree, but the respective
drivers will remove in future patches.
So remove the same instances.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The old 'sb' command was deprecated in 2015 and replaced with 'host'.
Remove the remaining users and the command, so that the name is available
for other purposes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a boot command to distro boot to support disks connected over the
VirtIO bus. The boot command uses the shared block environment.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
K3 based AM654 devices has DDR memory subsystem that comprises
Synopys DDR controller, Synopsis DDR phy and wrapper logic to
intergrate these blocks into the device. This DDR subsystem
provides an interface to external SDRAM devices. Adding support
for the initialization of the external SDRAM devices by
configuring the DDRSS registers and using the buitin PHY
routines.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: James Doublesin <doublesin@ti.com>
Convert the Watchdog driver for AT91SAM9x processors to support
the driver model and device tree. Changes "CONFIG_AT91SAM9_WATCHDOG"
to new "CONFIG_WDT_AT91" Kconfig option.
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
Add some description about pre-relocation driver binding, including
usage of DM_FLAG_PRE_RELOC flag and caveats.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add REAME.virtio to describe the information about U-Boot support for
VirtIO devices, including supported boards, build instructions, driver
details etc.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds ethernet support for the MIPS based Mediatek MT76xx SoCs
(e.g. MT7628 and MT7688), including a minimum setup of the integrated
switch. This driver is loosly based on the driver version included in
this MediaTek github repository:
https://github.com/MediaTek-Labs/linkit-smart-uboot.git
Tested on the MT7688 LinkIt smart-gateway and on the
Gardena-smart-gateway.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Frank Wunderlich <frankwu@gmx.de>
Cc: Weijie Gao <hackpascal@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There is no need to have README in all i.MX documents name.
Remove README from i.MX docs name and add .txt file extension.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
The Serial Download Protocol feature is availible in various
i.MX SoCs.
Move README.sdp document to imx/misc directory.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
The current High Assurance Boot document README.mxc_hab
include details for the following features in a single file:
- HAB Secure Boot
- HAB Encrypted Boot
Split HAB documentation in a specific directory for a cleaner
documentation structure, subsequent patches will include more
content in HAB documentation.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
The following documents describe device details according to the
i.MX family:
- README.imx25
- README.imx27
- README.imx5
- README.imx6
- README.mxs
Move all device common related document to doc/imx/common for a better
directory structure.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
The following documents describe the image type used by the mkimage
tool to generate U-Boot images for i.MX devices.
- README.imximage
- README.mxsimage
Move all mkimage related document to doc/imx/mkimage for a better
directory structure.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Currently the Serial Download Protocol tools and procedure are
documented in two places:
- doc/imx/README.sdp
- doc/imx/README.imx6
It is better to consolidate all SDP related information into
README.sdp file, so move the content from README.imx6 to
README.sdp.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Currently the U-Boot doc/ directory contains the following files
that are only relevant for i.MX devices:
- doc/README.imx25
- doc/README.imx27
- doc/README.imx5
- doc/README.imx6
- doc/README.imximage
- doc/README.mxc_hab
- doc/README.mxs
- doc/README.mxsimage
- doc/README.sdp
Move all content to a common i.MX folder for a better documentation
structure.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
There are some sections in current doc saying 64-bit is unsupported.
This apparently is out of date. Remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently only 32-bit U-Boot for QEMU x86 is documented. Mention
the 64-bit support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reword the documentation to make it clear the compatible string is now
optional, yet still matching on it takes precedence over PCI IDs and
PCI classes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Sandbox SPL/TPL support
Various dm-related improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlu9RL4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYd8gf+NYAGhpiEZZ5vc3DB4Xdn2okgakbbg0QQ
/b0Lr9xQsKgZthK0rvPlH2dXxf+ViAm1iHTy8KBCFi0SHNder48Zui9uTrX0NRq8
pLZGyJPXPYbiyc4pQTEJpTth4iShcphRVio0no4sLpNQqO4aQrialSLa9fnwd9Ra
1l9mF91aaYw6cG+/ejg3UR1LfsDdQ5bjubt0Fw0wGX9UvQOAz5gz5+a17wrz6+Gx
L0gzvyfbuLUhbWB36DXikrL14DAFys2uV9aHJ5zEd53l+F7ZHWsupCO0OtN66cV7
KpPKoYG7vhLqBXKpyrW20T+BPeSyDKmDQE6wbpECmEDOvKzvW67O/w==
=Bfjm
-----END PGP SIGNATURE-----
Merge tag 'dm-9oct18' of git://git.denx.de/u-boot-dm
Test improvements to tidy up output and drop duplicate tests
Sandbox SPL/TPL support
Various dm-related improvements
The DP83867 has a muxing option for the CLK_OUT pin. It is possible
to set CLK_OUT for different channels.
Create a binding to select a specific clock for CLK_OUT pin.
Based on commit 9708fb630d19 ("net: phy: dp83867: Add binding for
the CLK_OUT pin muxing option") of mainline linux kernel.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds support for enabling or disabling the lane swapping
(called "port mirroring" in PHY's CFG4 register) feature of the DP83867
TI's PHY device.
One use case is when bootstrap configuration enables this feature (because
of e.g. LED_0 wrong wiring) so then one needs to disable it in software
(at u-boot/Linux).
Based on commit fc6d39c39581 ("net: phy: dp83867: Add lane swapping
support in the DP83867 TI's PHY driver") of mainline linux kernel.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
At present it is not possible to specify that a node should be used before
relocation (in U-Boot proper) without it also ending up in SPL and TPL
device trees. Add a new "u-boot,dm-pre-proper" boolean property for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a way in configuration files (exlinux.conf for sysboot command)
to select a specific FIT configuration. The configuration is selected
with a string added after the FIT filename in the label "KERNEL" or
"LINUX", using the same format than bootm command:
KERNEL [Filename]#<conf>[#<extra-conf[#...]]
This configuration string, beginning by '#', is directly appended
to bootm argument 1 after <kernel_addr_r>.
bootm [<kernel_addr_r>]#<conf>[#<extra-conf[#...]]
see doc/uImage.FIT/command_syntax_extensions.txt for details
Example :
KERNEL /fit.itb#cfg1
KERNEL /fit.itb#cfg2
Configuration can be use also for overlay management :
KERNEL /fit.itb#cfg1#dtbo1#dtbo3
see doc/uImage.FIT/overlay-fdt-boot.txt for details
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
With CONFIG_OPTEE_TA_AVB use the trusted application AVB provided by
OP-TEE to manage rollback indexes and device-lock status.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Sync with c8bfafb15944 ("dt/bindings: add bindings for optee")
from Linux kernel.
Introduces linaro prefix and adds bindings for ARM TrustZone based OP-TEE
implementation.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
This adds QEMU RISC-V 'virt' board target support, with the hope of
helping people easily test U-Boot on RISC-V.
The QEMU virt machine models a generic RISC-V virtual machine with
support for the VirtIO standard networking and block storage devices.
It has CLINT, PLIC, 16550A UART devices in addition to VirtIO and
it also uses device-tree to pass configuration information to guest
software. It implements RISC-V privileged architecture spec v1.10.
Both 32-bit and 64-bit builds are supported. Support is pretty much
preliminary, only booting to U-Boot shell with the UART driver on
a single core. Booting Linux is not supported yet.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
This is the PR for SPI-NAND changes along with few spi changes.
[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a document to describe file system firmware loader binding
information.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide information about
- overview of file system firmware loader driver model
- describe storage device and partition in device tree source
- describe fie system firmware loader API
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the section about Device Trees add a paragraph at the end that
clarifies how we decide of a tree is valid or not. We say that all
bindings must either be in the specification (link provided) or in our
device-tree-bindings directory. We say that most of these come from the
Linux Kernel and as such some design decisions are made for us already,
but that in most cases we wish to retain compatibility.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Stefan is listed as a kirkwood maintainer since commit f822d8578b
(MAINTAINERS: Update Marvell custodianship).
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for K3 based remoteproc driver that
communicates with TISCI to start start a remote processor.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
K3 specific SoCs have a dedicated microcontroller for doing
resource management. Any HLOS/firmware on compute clusters should
load a firmware to this microcontroller before accessing any resource.
Adding support for loading this firmware.
After the K3 system controller got loaded with firmware and started
up it sends out a boot notification message through the secure proxy
facility using the TI SCI protocol. Intercept and receive this message
through the rproc start operation which will need to get invoked
explicitly after the firmware got loaded.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Secure Proxy module manages hardware threads that are meant
for communication between the processor entities. Adding
support for this driver.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Devices from the TI K3 family of SoCs like the AM654x contain a Device
Management and Security Controller (SYSFW) that manages the low-level
device control (like clocks, resets etc) for the various hardware
modules present on the SoC. These device control operations are provided
to the host processor OS through a communication protocol called the TI
System Control Interface (TI SCI) protocol.
This patch adds a system reset driver that communicates to the system
controller over the TI SCI protocol for allowing to perform a system-
wide SoC reset.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a power domain driver that communicates to the system
controller over the TI SCI protocol for performing power management of
various devices present on the SoC. Various power domain functionalities
are achieved by the means of different TI SCI device operations provided
by the TI SCI framework.
This code is loosely based on the drivers/soc/ti/ti_sci_pm_domains.c
driver of the Linux kernel.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a clock driver that communicates to the system
controller over the TI SCI protocol for performing clock management of
various devices present on the SoC. Various clock functionality is
achieved by the means of different TI SCI device operations provided by
the TI SCI framework.
This code is loosely based on the drivers/clk/keystone/sci-clk.c driver
of the Linux kernel.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a reset driver that communicates to the system
controller over the TI SCI protocol for performing reset management of
various devices present on the SoC. Various reset functionalities are
achieved by the means of different TI SCI device operations provided by
the TI SCI framework.
This code is loosely based on the drivers/reset/reset-ti-sci.c driver of
the Linux kernel.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Texas Instrument's System Control Interface (TI SCI) message protocol is
used in Texas Instrument's System on Chip (SoC) such as those in the K3
family AM654 SoC to communicate between various compute processors with
a central system controller entity.
The TI SCI message protocol provides support for management of various
hardware entities within the SoC. Add support driver to allow
communication with system controller entity within the SoC using the
mailbox client.
This is mostly derived from the TI SCI driver in Linux located at
drivers/firmware/ti_sci.c.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
arch/arm/Makefile references armv5 for backwards compatibility with
older compilers. This patch removes those references to armv5,
since by now newer compilers are required which should have armv7
support enabled.
The Makefile also also has a list of options for mtune, but the
entry for CONFIG_CPU_V7A is empty, so this patch tunes the
CPU_V7A architecture to generic-armv7-a.
The following size changed apply to omap3_logic using GCC.
Stock
text data bss dec hex filename
50910 429 67580 118919 1d087 spl/u-boot-spl
540713 22700 327072 890485 d9675 u-boot
Without Armv5
text data bss dec hex filename
50916 429 67580 118925 1d08d spl/u-boot-spl
540719 22700 327064 890483 d9673 u-boot
mtune=generic-armv7-a
text data bss dec hex filename
50932 429 67580 118941 1d09d spl/u-boot-spl
540519 22700 327080 890299 d95bb u-boot
Signed-off-by: Adam Ford <aford173@gmail.com>
There is no need to keep a separate coreboot_fb.dtsi since now we
have a generic coreboot payload dts.
While we are here, this also remove the out-of-date description in
the documentation regarding to coreboot framebuffer driver with
U-Boot loaded as a payload from coreboot. As the testing result with
QEMU 2.5.0 shows, the driver just works like a charm.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently building U-Boot as the coreboot payload requires user
to change the build configuration for a specific board during
menuconfig process. This uses the board's native device tree
to configure the hardware. For example, the device tree provides
PCI address range for the PCI host controller and U-Boot will
re-program all PCI devices' BAR to be within this range. In order
to make sure we don't mess up the hardware, we should guarantee
the range matches what coreboot programs the chipset.
But we really should make the coreboot payload support easier.
Just like EFI payload, we can create a generic coreboot payload
for all x86 boards as well. The payload is configured to include
as many generic drivers as possible. All stuff that touches low
level initialization are not allowed as such is the coreboot's
responsibility. Platform specific drivers (like gpio, spi, etc)
are not included.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Add u-boot,off-on-delay-us for fixed regulator.
Depends on board design, the gpio regulator sometimes
connects with a big capacitance. When need to off, then
on the regulator, if there is no enough delay,
the voltage does not drop to 0, so introduce this
property to handle such case.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Compressed images should have their compression property
set to "none" if U-Boot should leave them compressed.
This is especially the case for compressed ramdisks that
should be uncompressed by the kernel only.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
This command is part of the write partition sequence performed by
rkdeveloptool: one partition is first completely erased and
than wrote.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch implement reading blocks form selected device with
LBA addressing.
Corresponding command on workstation is:
rkdeveloptool rl <start_blk> <blk_cnt> <file>
While we support reading more than one blocks per K_FW_LBA_READ_10
request, rkdeveloptool and original rockchip tool do perform
chunk reads limiting the maximum size per chunk far lower
than max int values.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Chip Version is a string saved in BOOTROM address space Little Endian.
Ex for rk3288: 0x33323041 0x32303134 0x30383133 0x56323030
which brings: 320A20140813V200
Note that memory version do invert MSB/LSB so printing the char
buffer would show: A02341023180002V
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
At present all emulated sandbox pci devices must be present in the
device tree in order to be used. The real world pci uclass driver
supports pci device driver matching, and we should add such support
on sandbox too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds documentation of device tree bindings for the STM32 ADC.
It's based on linux-v4.18-rc* dt-bindings, at the time of writing:
- Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ePTT
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-07-25
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
patman's _ReadAliasFile only splits on spaces, not tabs, so the entries
for dinh and maxime weren't being recognised as valid. I'll fix patman
in a separate patch, but this makes all the entries consistent.
Signed-off-by: Adam Sampson <ats@offog.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Scott is no longer maintaining the NAND subsystem, mark as orphaned for
now.
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
This reverts commit c524997acb.
Booting ARMv7 in non-secure mode using bootefi works now.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Switch to the distro boot for UniPhier platform.
- Remove the environment vairalbes used to load images from raw
block devices.
- Keep the command to download images via tftp. This will be
useful to boot the kernel when no valid kernel image is ready
yet in the file system.
- Use root.cpio.gz instead of root.cpio.uboot because we always know
the file size of the init ramdisk; it is loaded via either a file
system or network.
- Rename fit_addr_r to kernel_addr_r, which the distro command
checks to get the load address of FIT image.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently the U-Boot project contains 2 documentation directories:
- doc/
- Documentation/
The Documentation directory only contains device tree bindings related
content, so move the 3 files to doc/device-tree-bindings/.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
1. Since libavb library alone is highly portable, introduce dedicated
Kconfig symbol for AVB bootloader-dependent operations, so it's possible
to build libavb separately. AVB bootloader-dependent operations include:
* Helpers to process strings in order to build OS bootargs.
* Helpers to access MMC, similar to drivers/fastboot/fb_mmc.c.
* Helpers to alloc/init/free avb ops.
2. Add CONFIG_FASTBOOT dependency, as fastboot buffer is
re-used in partition verification operations.
Reported-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Tested-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
The Linux kernel moved to sphinx-based documentation and got rid of the
DocBook based documentation quite a while ago. Hence, the DocBook
documentation for U-Boot should be converted as well.
To achieve this, import the necessary files from Linux v4.17, and
convert the current DocBook documentation (three files altogether) to
sphinx/reStructuredText.
For now, all old DocBook documentation was merged into a single
handbook, tentatively named "U-Boot Hacker Manual".
For some source files, the documentation style was changed to comply
with kernel-doc; no functional changes were applied.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Change the description relating to CONFIG_SPL_ROCKCHIP_BACK_TO_BROM to
clarify that both RK3288 and RK3036 use
CONFIG_SPL_ROCKCHIP_BACK_TO_BROM=y
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To let the full U-Boot know where it was booted from (i.e. which of
the entries in /chosen/u-boot,spl-boot-order' contained a valid
image), we define (and document) /chosen/u-boot,spl-boot-device as the
property that could/should automatically be injected by SPL.
This commit only contains a documentation change, which documents the
new property and the intended usage.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
HSE and LSE bypass shall support both analog and digital signals.
This patch add a way to select digital bypas case in the device tree
and set the associated bit DIGBYP in RCC_BDCR and RCC_OCEN register
during clock tree initialization.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support for loading U-Boot on the Broadcom 7445 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Support a default memory bank, specified in reg, as well as
board-specific memory banks in subtree board-id nodes.
This allows memory information to be provided in the device tree,
rather than hard-coded in, which will make it simpler to handle
similar devices with different memory banks, as the board-id values
or masks can be used to match devices.
Signed-off-by: Michael Pratt <mpratt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
To build U-Boot on a Nyan Big Chromebook the docs outline adjusting the Tegra124
defined CONFIG_SYS_TEXT_BASE but this has since been moved to individual config
files. We should have the default required for U-Boot chain loading on the
chromebook as the default CONFIG_SYS_TEXT_BASE and update the docs to remove
this now non required step.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This updates the doc to mention chain-loading an x86 kernel via
'bootefi' command, along with several typos fix.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexander Graf <agraf@suse.de>
CONFIG_EFI_LOADER is fully supported on x86 now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexander Graf <agraf@suse.de>
Contains:
1. Overview of Android Verified Boot 2.0
2. Description of avb subset of commands
3. Examples of errors when boot/vendor/system/vbmeta partitions
are tampered
4. Examples of enabling AVB2.0 on your setup
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
To avoid confusion, let's rename the efi-x86 target to efi-x86_app.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is possible to create a generic EFI payload for all x86 boards.
The payload is configured to include as many generic drivers as
possible. All stuff that touches low-level initialization are not
allowed as such is the EFI BIOS's responsibility. Platform specific
drivers (like gpio, spi, etc) are not included.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present the EFI application and payload support codes in the x86
directory is distributed in a hybrid way. For example, the Kconfig
options for both app and payload are in arch/x86/lib/efi/Kconfig,
but the source codes in the same directory get built only for
CONFIG_EFI_STUB.
This refactors the codes by consolidating all the EFI support codes
into arch/x86/cpu/efi, just like other x86 targets.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit f3b5056c4e ("efi_loader: split README.efi into two
separate documents"), the original README.efi was renamed to
README.u-boot_on_efi, but x86 doc still refers to the old one.
This updates the x86 doc to reference both README.u-boot_on_efi and
README.uefi.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Currently both pirq_reg_to_linkno() and pirq_linkno_to_reg() assume
consecutive PIRQ routing control registers. But this is not always
the case on some platforms. Introduce a new device tree property
intel,pirq-regmap to describe how the PIRQ routing register offset
is mapped to the link number and adjust the irq router driver to
utilize the mapping.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As README.x86 already mentions, there are two SPI flashes mounted
on Intel Cougar Canyon 2 board, called SPI-0 and SPI-1 respectively.
SPI-0 stores the flash descriptor and the ME firmware. SPI-1 stores
the actual BIOS image which is U-Boot. Building a single image with
both ME firmware and U-Boot does not make sense.
This also describes the exact flash location where the u-boot.rom
should be programmed in the documentation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit removes text that is exact duplicated of the text above.
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
With 'make htmldocs' we can generate a documentation if the function
comments follow the DocBook conventions.
This patch adjusts the comments for EFI boot services and provides the
DocBook template for the EFI subsystem.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Update the list of missing functionality for boottime and runtime services.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Rename
nx25 as ax25
ae250 as ae350
nx25-ae250 as ax25-ae350
including filename, variable, string and definition.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
For pinctrl driver of mvebu, the compatible strings
supported are defined differently from Linux version.
The patch aligned the compatible string with
Linux 4.17-rc4.
Signed-off-by: Evan Wang <xswang@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Sync sun4i-usb-phy bindings from Linux, since the
drivers/phy/allwinner/phy-sun4i-usb.c follow similar.
Sync changes from Linux with below commit:
"phy: sun4i-usb: add support for R40 USB PHY"
(sha1: f3d96f8d23d8e6d0b7642ee946b9b2ac3418fb4d)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Now that U-Boot works fine with highmem enabled, there is no need to
tell users to disable highmem.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
Describe U_BOOT_CMD_COMPLETE.
Describe the arguments of U_BOOT_CMD and U_BOOT_CMD_COMPLETE.
Describe the arguments of the command function.
Describe the arguments of the completion function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
