Commit graph

13 commits

Author SHA1 Message Date
Michal Simek
dd0ebfe8a4 arm64: zynqmp: Remove comment about gem spec in kv260
The latest SOM specification doesn't enforce certain MIO lines allocated
for ethernet or ethernet controller itself. That's why remove comment about
it which is likely there from early version of specification.
Also removed the same comment from pinctrl node. It is clear that it has to
be defined for different carrier cards.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9406377bf2c391ac0200670511bd6b0edb097c96.1676880543.git.michal.simek@amd.com
2023-03-09 13:15:00 +01:00
Michal Simek
8489b6d2e3 arm64: zynqmp: Fill model name for SOM CCs
When U-Boot do DTB reselection origin model for SOM is used and from log it
is not visible if DTB was switched or not. That's why add model directly to
CC (carrier card) to show new model if reselection was successful.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/49ba1007218496c48d287454e84a5b8c08abc692.1674043452.git.michal.simek@amd.com
2023-01-24 13:58:49 +01:00
Ashok Reddy Soma
b8745e7eb4 arm64: zynqmp: Fix usb node drive strength and slew rate
As per design, all input/rx pins should have fast slew rate and 12mA
drive strength. Rest all pins should be slow slew rate and 4mA drive
strength. Fix usb nodes as per this and remove setting of slow slew rate
for all the usb gorup pins.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/b245c165f05845c1f3ab41a92c82b7ec1538cee4.1655288171.git.michal.simek@amd.com
2022-06-24 14:17:18 +02:00
Michal Simek
b611f7faf9 arm64: zynqmp: Enable DP for kv260-revA board
DP is enabled for revB and should be enabled for kv260-revA too. Changes in
other boards were done by commit 8b82a3a7fe ("arm64: zynqmp: Enable DP
driver for SOMs").

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/4e273bce3a8acf4495b67b702b1704acec8d9ccb.1654779436.git.michal.simek@amd.com
2022-06-24 14:14:25 +02:00
Michal Simek
2f6e1dde38 arm64: zynqmp: Fix level of gpio reset for usb on kv260 boards
Active level is low that's why it should be fixed.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/86b3a96ce990b0ee0adab221146b5a5c751bd4a9.1645629459.git.michal.simek@xilinx.com
2022-03-07 16:33:47 +01:00
Michal Simek
ff79448294 arm64: zynqmp: Switch to ethernet-phy-id in kv260
Use ethernet-phy-id compatible string to properly describe phy reset on
kv260 boards. Previous description wasn't correct because reset was done
for mdio bus to operate and it was in this case used for different purpose
which was eth phy reset. With ethernet-phy-id phy reset happens only for
the phy via phy framework.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/73b64f1a2b873b4e26bd2b365364bdf313794ae2.1645629459.git.michal.simek@xilinx.com
2022-03-07 16:33:47 +01:00
Michal Simek
a3efa53c01 arm64: zynqmp: Use assigned-clock-rates for setting up clock in SOM
With limited low level configuration done via psu-init only IPs connected
on SOM are initialized and configured. All IPs connected to carrier card
are not initialized. There is a need to do proper reset, pin configuration
and also clock setting.
The patch targets the last part which is setting up proper clock for USBs
and SDs.
Also setup proper bus width for SD cards.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Link: https://lore.kernel.org/r/d9f80b2551bd246c3d7ecb09b516806c8dc83ed9.1645629459.git.michal.simek@xilinx.com
2022-03-07 16:33:47 +01:00
Michal Simek
59e1bdd48d arm64: zynqmp: Setup clock for DP and DPDMA
Clocks are coming from shared HW design where these frequencies should be
aligned with PLL setup.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/04454c50d0d13e450976942085d763ab5aa38f98.1645629459.git.michal.simek@xilinx.com
2022-03-07 16:33:47 +01:00
Michal Simek
464f6558ca arm64: zynqmp: Fix header alignment on kv260 boards
Fix header alignment.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-26 08:08:11 +02:00
Manish Narani
15ca9ebb07 arm64: zynqmp: Move USB3 PHY properties from DWC3 node to USB node
Move the PHY properties from DWC3 node to USB node in ZynqMP DTs as here
the USB3 PHY used is PSGTR, which is connected to Xilinx USB core. This
PHY initialization should be handled from Xilinx USB core as the
prerequisite register configurations are done here only.

Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-07-26 09:26:41 +02:00
Michal Simek
3972ae65e4 arm64: zynqmp: Add missing year in Kria dts files
DT files have been added this year but forgot to update it that's why do it
in separate patch now.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:36 +02:00
Michal Simek
b6d8d4b100 arm64: zynqmp: Use overlay sugar syntax for Kria SOM
dtc supports new sugar syntax which is easier compare to previous one
that's why also covert overlays for SOM to it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
a502a87bc0 arm64: zynqmp: Add description for SOM/Kria boards
The patch contains several DT files for SOM platform.
Carrier card is sck-kv (KV260) revA/B. SMK-K26 is description for starter
kit which doesn't have EMMC populated. And SM-K26 is full som with EMMC.

Files are divided in this way to make sure that SOM can be plugged to
different carrier card and all peripherals on SOM (or defined by a spec) can
be used by U-Boot. Full DT for SOM+CC can be merged together as overlays.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-05-19 09:44:50 +02:00