We can safely remove it, because none of the currently supported
boards uses these features.
The existing implementation had multiple problems:
- unnecessary code duplication between sun4i/sun5i/sun7i
- ZQ calibration was never initiated explicitly, and could be
only triggered by setting the highest bit in the 'zq' parameter
in the 'dram_para' struct (this was never actually done for
any of the known Allwinner devices).
- even if the ZQ calibration could be started, no attempts were
made to wait for its completion, or checking whether the
default automatically initiated ZQ calibration is still
in progress
- ODT was only ever enabled on sun4i, but not on sun5i/sun7i
Additionally, SDR_IOCR was set to 0x00cc0000 only on sun4i. There
are some hints in the Rockchip Linux kernel sources, indicating
that these bits are related to the automatic I/O power down
feature, which is poorly understood on sunxi hardware at the
moment. Avoiding to set these bits on sun4i too does not seem to
have any measurable/visible impact.
The impedance and ODT configuration code will be re-introdeced in
one of the next comits.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Before driving the CKE pin (Clock Enable) high, the DDR3 spec requires
to wait for additional 500 us after the RESET pin is de-asserted.
The DRAM controller takes care of this delay by itself, using a
configurable counter in the SDR_IDCR register. This works in the same
way on sun4i/sun5i/sun7i hardware (even the default register value
0x00c80064 is identical). Except that the counter is ticking a bit
slower on sun7i (3 DRAM clock cycles instead of 2), resulting in
longer actual delays for the same settings.
This patch configures the SDR_IDCR register for all sun4i/sun5i/sun7i
SoC variants and not just for sun7i alone. Also an explicit udelay(500)
is added immediately after DDR3 reset for extra safety. This is a
duplicated functionality. But since we don't have perfect documentation,
it may be reasonable to play safe. Half a millisecond boot time increase
is not that significant. Boot time can be always optimized later.
Preferebly by the people, who have the hardware equipment to check the
actual signals on the RESET and CKE lines and verify all the timings.
The old code did not configure the SDR_IDCR register for sun4i/sun5i,
but performed the DDR3 reset very early for sun4i/sun5i. This resulted
in a larger time gap between the DDR3 reset and the DDR3 initialization
steps and reduced the chances of CKE delay timing violation to cause
real troubles.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The RESET pin needs to be kept low for at least 200 us according
to the DDR3 spec. So just do it the right way.
This issue did not cause any visible major problems earlier, because
the DRAM RESET pin is usually already low after the board reset. And
the time gap before reaching the sunxi u-boot DRAM initialization
code appeared to be sufficient.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
If the dram->ppwrsctl (SDR_DPCR) register has the lowest bit set to 1,
this means that DRAM is currently in self-refresh mode and retaining the
old data. Since we have no idea what to do in this situation yet, just
set this register to 0 and initialize DRAM in the same way as on any
normal reboot (discarding whatever was stored there).
This part of code was apparently used by the Allwinner boot0 bootloader
to handle resume from the so-called super-standby mode. But this
particular code got somehow mangled on the way from the boot0 bootloader
to the u-boot-sunxi bootloader and has no chance of doing anything even
remotely sane. For example:
1. in the original boot0 code we had "mctl_write_w(SDR_DPCR,
0x16510000)" (write to the register) and in the u-boot it now looks
like "setbits_le32(&dram->ppwrsctl, 0x16510000)" (set bits in the
register)
2. in the original boot0 code it was issuing three commands "0x12, 0x17,
0x13" (Self-Refresh entry, Self-Refresh exit, Refresh), but in the
u-boot they have become "0x12, 0x12, 0x13" (Self-Refresh entry,
Self-Refresh entry, Refresh)
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The attempt to do DRAM parameters calibration in 'dramc_scan_dll_para()'
function by trying different DLL adjustments and using the hardware
DQS gate training result as a feedback is a great source of inspiration,
but it just can't work properly the way it is implemented now. The fatal
problem of this implementation is that the DQS gating window can be
successfully found for almost every DLL delay adjustment setup that
gets tried. Thus making it unable to see any real difference between
'good' and 'bad' settings.
Also this code was supposed to be only activated by setting the highest
bit in the 'dram_tpr3' variable of the 'dram_para' struct (per-board
dram configuration). But none of the linux-sunxi devices has ever used
it for real. Basically, this code is just a dead weight.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Automatic booting using an extlinux.conf file requires various environment
variables to be set.
Also modify CONFIG_SYS_LOAD_ADDR and CONFIG_STANDALONE_LOAD_ADDR to match
the value chosen for kernel_addr_r, see the added comment for why the new
value is chosen.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Use the new standard bootcmd from <config_distro_bootcmd.h>.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
This generic $bootcmd, and associated support macros, automatically
searches a defined set of storage devices (or network protocols) for an
extlinux configuration file or U-Boot boot script in various standardized
locations. Distros that install such a boot config file/script in those
standard locations will get easy-to-set-up booting on HW that enables
this generic $bootcmd.
Boards can define the set of devices from which boot is attempted, and
the order in which they are attempted. Users may later customize this
set/order by edting $boot_targets.
Users may interrupt the boot process and boot from a specific device
simply by executing e.g.:
$ run bootcmd_mmc1
or:
$ run bootcmd_pxe
This patch was originally written by Dennis Gilmore based on Tegra and
rpi_b boot scripts. I have made the following modifications since then:
* Boards must define the BOOT_TARGET_DEVICES macro in order to specify
the set of devices (and order) from which to attempt boot. If needed,
we can define a default directly in config_distro_bootcmd.h.
* Removed $env_import and related variables; nothing used them, and I
think it's better for boards to pre-load an environment customization
file using CONFIG_PREBOOT if they need.
* Renamed a bunch of variables to suit my whims:-)
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
SYS_CPU, SYS_BOARD and SYS_SOC are identical for all sunxi boards, move
them to a shared code block.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
config_distro_defaults.h which is include later will redefine CONFIG_CMD_NET,
drop the useless / meaningless undef of it.
While at also move the undef of CONFIG_CMD_FPGA up to directly under the
include of config_cmd_defaults.h, to make it clear that it overwrites
the setting done from config_cmd_defaults.h .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
I see no reason to override the choice to include this from
config_cmd_defauls.h .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We undef CONFIG_CMD_NET at line 167, and there is nothing re-defining it
between line 167 and the #ifdef CONFIG_CMD_NET, so remove this effectively
dead block.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
sunxi does not need this and it should never have been enabled for it in
the first place.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
most todays LCDs support 32bpp e.g. the framebuffer memory is 32bpp
organized.
To support 24bpp BMPs we need to take only 3 byte from the bpp and set
one byte from the FB to 0.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Since rgb2ycbcr_coeff and friends are declared const, but assigned
to a void pointer, clang will warn that the const is implicity casted
away. If the pointer is changed to void const * gcc will warn when it
is implicitly casted to a const int array. Just add a correctly
typed pointer instead to prevent these casts and hence the warnings.
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Instead of waiting for DC triple buffer to be cleared, this patch
changes to wait for a relevant DP sync flow end interrupt to come
when disabling sync BG flows. In this way, we align the implement
to the freescale internal IPUv3 driver. After applying this patch,
an uboot hang up issue at the arch_preboot_os() stage, where we
disable a relevant ipu display channel, is not observed any more on
some MX6DL platforms.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
- Adds support for a minimal framebuffer driver of TI's AM335x SoC
to be compatible with Wolfgang Denk's LCD-Framework (CONFIG_LCD,
common/lcd.c)
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
This patch removes following two functions:
- lcd_getbgcolor(...)
not used somewhere outside lcd.c, internally we use now the global
variable lcd_color_bg (was return value of function before)
- lcd_getfgcolor(...)
not used in any place of u-boot
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
[agust: rebased]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Use the new API which is originally taken out from boot_get_kernel
of bootm.c
Signed-off-by: Bryan Wu <pengw@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
[trini: Fix warnings with CONFIG_FIT]
Signed-off-by: Tom Rini <trini@ti.com>
Trying bootm for zImage will print out several error message which
is not necessary for this case. So detect image format firstly, only
try bootm for legacy and FIT format image then try bootz for others.
This patch needs new function genimg_get_kernel_addr().
Signed-off-by: Bryan Wu <pengw@nvidia.com>
Kernel address is normally stored as a string argument of bootm or bootz.
This function is taken out from boot_get_kernel() of bootm.c, which can be
reused by others.
Signed-off-by: Bryan Wu <pengw@nvidia.com>
[trini: Fix warnings with CONFIG_FIT]
Signed-off-by: Tom Rini <trini@ti.com>
Switch core maintainer to Tom Rini. Adapt directory layout for
git tree detection.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
If a 32-bit system has 2GB of RAM, and the base address of that RAM is
2GB, then start+size will overflow a 32-bit value (to a value of 0).
__lmb_alloc_base is affected by this; it calculates the minimum of
(start+size of RAM) and max_addr. However, when start+size is 0, it
is always less than max_addr, which causes the value of max_addr not
to be taken into account when restricting the allocation's location.
Fix this by calculating start+size separately, and if that calculation
underflows, using -1 (interpreted as the max unsigned value) as the
value instead, and then taking the min of that and max_addr. Now that
start+size doesn't overflow, it's typically large, and max_addr
dominates the min() call, and is taken into account.
The user-visible symptom of this bug is that CONFIG_BOOTMAP_SZ is ignored
on Tegra124 systems with 2GB of RAM, which in turn causes the DT to be
relocated at the very end of RAM, which the ARM Linux kernel doesn't map
during early boot, and which causes boot failures. With this fix,
CONFIG_BOOTMAP_SZ correctly restricts the relocated DT to a much lower
address, and everything works.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Replace the custom $bootcmd with that from <config_distro_bootcmd.h>.
There should be no functional change, since the new generic $bootcmd was
derived strongly from tegra-common-post.h, after which this part of
rpi_b.h was modelled.
The #defines to enable/disable U-Boot commands/features were moved
earlier in rpi_b.h, so they are set up before config_distro_bootcmd.h
is included, since it tests whether certain features should be included
based on those defines.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Replace the custom $bootcmd with that from <config_distro_bootcmd.h>.
There should be no functional change, since the new generic $bootcmd was
derived strongly from tegra-common-post.h.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This generic $bootcmd, and associated support macros, automatically
searches a defined set of storage devices (or network protocols) for an
extlinux configuration file or U-Boot boot script in various standardized
locations. Distros that install such a boot config file/script in those
standard locations will get easy-to-set-up booting on HW that enables
this generic $bootcmd.
Boards can define the set of devices from which boot is attempted, and
the order in which they are attempted. Users may later customize this
set/order by edting $boot_targets.
Users may interrupt the boot process and boot from a specific device
simply by executing e.g.:
$ run bootcmd_mmc1
or:
$ run bootcmd_pxe
This patch was originally written by Dennis Gilmore based on Tegra and
rpi_b boot scripts. I have made the following modifications since then:
* Boards must define the BOOT_TARGET_DEVICES macro in order to specify
the set of devices (and order) from which to attempt boot. If needed,
we can define a default directly in config_distro_bootcmd.h.
* Removed $env_import and related variables; nothing used them, and I
think it's better for boards to pre-load an environment customization
file using CONFIG_PREBOOT if they need.
* Renamed a bunch of variables to suit my whims:-)
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
1. Failure to set the return code correctly
2. Failure to detect the loop end condition when the value is equal to
the modulus.
Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Simon Glass <sjg@chromium.org>
The following configs are not defined at all.
- CONFIG_OMAP1510
- CONFIG_OMAP_1510P1
- CONFIG_OMAP_SX1
- CONFIG_OMAP3_DMA
- CONFIG_OMAP3_ZOOM2
- CONFIG_OMAP_INNOVATOR
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
This brings in changes up to commit f9e91a48 in the libfdt repo.
Mostly this is whitespace/minor changes. But there are a few new
features:
- fdt_size_cells() and fdt_address_cells()
- fdt_resize()
Signed-off-by: Simon Glass <sjg@chromium.org>
- Add 'p1023rds' to the list since commit d0bc5140 dropped
the board support but missed to update this file
- Fill the Commit and Removed Date fields for boards removed
by earlier commits
- Move 'incaip' to keep the list sorted in reverse
chronological order
- Describe the soring rule in the comment block:
"The list should be sorted in reverse chronological order."
- Fix typos in the comment block
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Currently, the BOOTP code sends out its initial request as soon as the
Ethernet driver indicates "link up". If this packet is lost or not
replied to for some reason, the code waits for a 1s timeout before
retrying. For some reason, such early packets are often lost on my
system, so this causes an annoying delay.
To optimize this, modify the BOOTP code to have very short timeouts for
the first packet transmitted, but gradually increase the timeout each
time a timeout occurs. This way, if the first packet is lost, the second
packet is transmitted quite quickly and hence the overall delay is low.
However, if there's still no response, we don't keep spewing out packets
at an insane speed.
It's arguably more correct to try and find out why the first packet is
lost. However, it seems to disappear inside my Ethenet chip; the TX chip
indicates no error during TX (not that it has much in the way of
reporting...), yet wireshark on the RX side doesn't see any packet.
FWIW, I'm using an ASIX USB Ethernet adapter. Perhaps "link up" is
reported too early or based on the wrong condition in HW, and we should
add some fixed extra delay into the driver. However, this would slow down
every link up event even if it ends up not being needed in some cases.
Having BOOTP retry quickly applies the fix/WAR to every possible
Ethernet device, and is quite simple to implement, so seems a better
solution.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Remove the duplicated argument to | in two places. Reported
by Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Maxin B. John <maxin.john@enea.com>
I happened to spot this while working in the area.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
file_size was being calculated using back-ticks but map_size uses
$(shell ...). Update the file_size calculation to use $(shell ...).
From: Jeroen Hofstee <jeroen@myspectrum.nl>
The binary_size_check target relies on stat -c %s
to return the size of u-boot.bin. This only works
with GNU stat though. Use wc instead.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
When "pxe boot" downloads the initrd/kernel/DTB, netboot_common() saves
the downloaded filename to global variable BootFile. If the boot
operation is aborted, this global state is not cleared. If "dhcp" is
executed later without any arguments, BootFile is not cleared, and when
the DHCP response is received, BootpCopyNetParams() writes the value into
environment variable bootfile.
This causes the following scenario:
* Boot script executes dhcp; pxe get; pxe boot
* User CTRL-C's the PXE menu, which causes the first menu item to be
booted, which causes some file to be downloaded.
(This boot-on-CTRL-C behaviour is arguably a bug too, but it's a
separate bug and the bug this patch fixes would still exist if the user
simply waited to press CTRL-C until "pxe boot" started downloading
files)
* User CTRL-C's the file downloads, but the filename is still written to
the bootfile environment variable.
* User re-runs the boot command, which in my case executes "dhcp; pxe get;
pxe boot" again, and "dhcp" picks up the saved bootfile environment
variable and proceeds to download a file that it shouldn't.
To solve this, modify the implementation of "pxe get" to clear BootFile
if the whole boot operation fails, which avoids this whole mess.
An alternative would be to modify netboot_common() such that the no-
arguments case explicitly clears the global variable BootFile. However,
that would prevent the following command sequences from working:
$ dhcp filename # downloads "filename"
$ dhcp # downloads $bootfile, i.e. "filename"
or:
$ setenv bootfile filename
$ dhcp # downloads $bootfile, i.e. "filename"
... and I assume someone relies on U-Boot working that way.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The Android fastboot client only communicates with specific vendor IDs.
This addition to the documentation points out that fact so everyone is
aware that not just any vendor ID will work and where to find the IDs
that will.
Signed-off-by: Clifton Barnes <cabarnes@indesign-llc.com>
Cc: Rob Herring <robh@kernel.org>
After the clean up performed in the commit 1151b7ac10b81ecbb the DFU subsystem
requires absolute patch for correct operation.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
