This change fixes the bad gpio configuration for the exynos dwmmc.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Beomho Seo <beomho.seo@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The byte order of soc revision was inverted, now it is fixed.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
On DRA72x, EMIF supports DDR3 upto 667MHz.
Adding the required settings for DDR3 at 666MHz and enabling it.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
To reduce code duplication update am335x_igep0033.h to use ti_am335x_common.h
and convert to generic board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
OMAP GPMC driver used with some NAND Flash devices (e.g. Spansion
S34ML08G1) causes that U-boot shows hundreds of 'nand: bit-flip
corrected' error messages. Possible cause was discussed in the
mailinglist thread:
http://lists.denx.de/pipermail/u-boot/2014-April/177508.html
Quote (Author: Pekon Gupta <pekon@ti.com>): "The issue is mainly
due to a NAND protocol violation in the omap driver since the
Random Data Output command (05h-E0h) expects to see only the
column address that should be addressed within the already loaded
read page into the read buffer. Only 2 address cycles with ALE
active should be provided between the 05h and E0h commands. The
Page read command expects the full address footprint (2bytes for
column address + 3bytes for row address), but once the page is
loaded into the read buffer, Random Data Output should be used
with only 2bytes for column address."
This patch combines the solution proposed in the mailinglist and
the patch provided by the Spansion company (GPLv2 code, source:
http://www.spansion.com/Support/Software/u-boot-psp-04.04.00.01-NAND.zip)
Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
Since the CS of a device connected to the GPMC was
stored in the global variable, it was not possible to
use multiple devices. In this patch the CS is stored per
device in its 'struct omap_nand_info'. This makes it
possible to use up to 'GPMC_MAX_CS' NAND Flash devices
connected to U-boot.
Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
In case when 4K page keystone RBL layout is used the compilation
error is appeared. That's because the #ifdef has to be placed under
struct name. This patch correct it.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The help message in board/ti/am335x/Kconfig says AM335x has
6 UARTs, so the valid number for CONFIG_CONS_INDEX is from 1 to 6.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
There is no reason to redefine pure readl/writel functions.
So remove this redundancy.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Vitaly Andrianov <vitalya@ti.com>
The mask for BWADJ field of PASSPLLCTL0 register has to be 0xff, but
by mistake, here is used shift instead of mask, so correct it.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
When enable debug option to compile, it will give the following
warning, this patch is used to get rid of it.
--->8---
warning: 'flags' is used uninitialized in this function [-Wuninitialized]
---8<---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
When enable debug option to compile, it will give the following
warning, this patch is used to get rid of it.
--->8---
warning: 'flags' is used uninitialized in this function [-Wuninitialized]
---8<---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
This allows the USB code to determine whether a USB bus reset was issued,
which in turn allows the code to differentiate between a detach (return
to shell prompt) and a board reset/reboot request.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
New dfu_usb_get_reset() method is necessary to distinct two different
use cases of dfu-util program.
This method checks if the USB bus reset has been really performed after
DFU DETACH.
Without this function the previous DFU behavior is preserved.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
This commit provides distinction between DFU device detach and reset.
The -R behavior is preserved with proper handling of the dfu-util's -e
switch, which detach the DFU device.
By running dfu-util -e; one can force device to finish the execution of
dfu command on target and execute some other scripted commands.
Moreover, some naming has been changed - the dfu_reset() method now is known
as dfu_detach(). New name better reflects the purpose of the code.
It was also necessary to increase the number of usb_gadget_handle_interrupts()
calls since we also must wait for detection of the USB reset event.
Example usage:
1. -e (detach) switch
dfu-util -a0 -D file1.bin;dfu-util -a3 -D uImage;dfu-util -e
access to u-boot prompt.
2. -R (reset) switch
dfu-util -a0 -D file1.bin;dfu-util -R -a3 -D uImage
target board reset
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Some drivers (e.g. net/e1000) reference these functions. So, this
fixes the build of MVBC_P board.
I'm not familiar with the MPC5xxx platform, maybe a full
implementation shall be implemented instead of this stub in the
future.
Signed-off-by: Vasili Galka <vvv444@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>, Marek Vasut <marex@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
The gpio command mostly relies on gpio_request() and gpio_free() being
nops, in that you can request a GPIO twice. With driver model this is
now implemented correctly, so it fails.
Change the command to deal with a failure to claim the GPIO.
Signed-off-by: Simon Glass <sjg@chromium.org>
The GPIO list is very long in many cases and most of them are not used.
By default, show only the GPIOs that are in use, and provide a flag to show
all of them. This makes the 'gpio status' command much more pleasant.
In order to do this, driver model now exposes a method for obtaining the
'function' of a GPIO, which describes whether it is an input or output, for
example. Implementation of this method is optional.
Signed-off-by: Simon Glass <sjg@chromium.org>
The QS Systems TQMa6 board support was added by commit cb07d74e
and lost by commit e82abaeb.
Commit e82abaeb merged the IMX branch based on pre-Kconfig
and the mainline based on post-Kconfig, simply deleting
the boards.cfg file. As a result, some boards added just before
the merge were lost.
This commit adds Kconfig, defconfig, MAINTAINERS for TQMa6 board
to work on the Kconfig infrastructure.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Stefano Babic <sbabic@denx.de>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Nomadik board select menu to nomadik/Kconfig.
Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="nomadik").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Orion5x board select menu to orion5x/Kconfig.
Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="orion5x").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Keystone board select menu to keystone/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="keystone").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP5 board select menu to omap5/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap5").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP4 board select menu to omap4/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap4").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP3 board select menu to omap3/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap3
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Davinci board select menu to davinci/Kconfig.
Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="davinci").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Exynos board select menu to exynos/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="exynos").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the KirkWood board select menu to kirkwood/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="kirkwood").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Prafulla Wadasdkar <prafulla@marvell.com>
Cc: Luka Perkov <luka@openwrt.org>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Rmobile board select menu to rmobile/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="rmobile").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Tegra board select menu to tegra/Kconfig.
Insert the Tegra SoC select menu between the arch select and the
board select.
Architecture select
|-- Tegra Platform (Tegra)
|- Tegra SoC select (Tegra20 / 30 / 114 / 124)
|- Board select
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="tegra*") and always "select" CONFIG_SPL as follows:
config TEGRA
bool
select SPL
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Zynq board select menu to zynq/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="zynq").
Refactor board/xilinx/zynq/MAINTAINERS too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Commit 41623c9 'arm: move exception handling out of start.S files' missed some
linker scripts. Hence, some boards no longer had exception handling linked since
this commit. Restore the original behavior by adding the .vectors section to
these linker scripts.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Newer FLASH types used on these boards don't allow writing of subpages.
So disable subpage write in the NAND driver. Additionally we need to
tell the UBI layer in the kernel that he also should only write 2048
bytes. This is done with an additional command line parameter for the
kernel commandline.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Make it configurable to disable subpage writes like the DaVinci NAND
driver already does.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Scott Wood <scottwood@freescale.com>
- Drop DEBUG
- Drop defines we can use the default of.
- Provide a larger malloc pool.
- Correct default locations for kernel / initrd / device tree
Signed-off-by: Tom Rini <trini@ti.com>
The default format for arm64 Linux kernels is the "Image" format,
described in Documentation/arm64/booting.txt. This, along with an
optional gzip compression on top is all that is generated by default.
The Image format has a magic number within the header for verification,
a text_offset where the Image must be run from, an image_size that
includes the BSS and reserved fields.
This does not support automatic detection of a gzip compressed image.
Signed-off-by: Tom Rini <trini@ti.com>
The Documentation/arm64/booting.txt document says that pass in x1/x2/x3
as 0 as they are reserved for future use.
Signed-off-by: Tom Rini <trini@ti.com>
The bcm_ep board configuration is used by a number of boards
including Cygnus and NSP.
Add builds for the bcm958300k and the bcm958622hr boards.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Base support for the Broadcom NSP SoC.
Based on iproc-common and the SoC specific reset function.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
