The MMC controller driver is (and ought to be) the only user of these
register definitions. Put them in a header next to the driver to remove
the dependency on a specific ARM platform's headers.
Due to the sunxi_mmc_init() prototype, the file was not renamed. None of
the register definitions were changed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
DM_GPIO is always enable in U-Boot proper for ARCH_SUNXI, and this
driver is never enabled in SPL, so the condition is always true.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
So far we have a convoluted #ifdef mesh that guards the early AXP PMIC
setup in board.c. That combination of &&, || and negations is very hard
to read, maintain and especially to extend.
Fortunately we have those same conditions already modelled in the
Kconfig file, so they are actually redundant. On top of that the real
reason we have those preprocessor guards in the first place is about the
symbols that are *conditionally* defined: without #ifdefs the build
would break because of them being undefined for many boards.
To simplify this, just change the guards to actually look at the symbols
needed, so CONFIG_AXP_xxx_VOLT instead of CONFIG_AXPyyy_POWER.
This drastically improves the readability of this code, and makes adding
PMIC support a pure Kconfig matter.
Doing this revealed one bug in Kconfig: there is no axp_set_dcdc4() for
the AXP818, even though CONFIG_AXP_DCDC4_VOLT includes that PMIC.
Since the AXP818 wasn't included when calling axp_set_dcdc4() in board.c,
this wasn't an issue, but becomes one now, so also remove the AXP818 from
the DCDC4 Kconfig symbol.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
- Fix some issues Coverity has reported, update MAINTAINERS file,
another bootstd fix, typo fix in error message, gitignore fix and
update TI's URL in many places.
During bootstd scanning for bootdevs, if bootdev_hunt_drv() encounters
a device not found error (e.g. ENOENT), let it return a successful status
so that bootstd will continue scanning the next devices, not stopping
prematurely.
Background:
During scanning for bootflows, it's possible for bootstd to encounter a
faulty device controller. Also when the same u-boot is used for another
variant of the same board, some device controller such as SATA might
not exist.
I've found this issue while converting the Marvell Sheevaplug board to
use bootstd. This board has 2 variants, the original Sheevaplug has MMC and
USB only, but the later variant comes with USB, MMC, and eSATA ports. We
have been using the same u-boot (starting with CONFIG_IDE and later with DM
CONFIG_SATA) for both variants. This worked well with the old
envs-scripting booting scheme.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A power domain id on sandbox should be in the range from zero to
ARRAY_SIZE(scmi_pwdom) - 1. Correct the validity check logic.
Addresses-Coverity-ID: 467401 ("Out-of-bounds write")
Addresses-Coverity-ID: 467405 ("Out-of-bounds read")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
When we do not have CONFIG_BOUNCE_BUFFER enabled, inside of
scsi_init_dev_desc_priv we never set the 'bb' field to false, we only
initialize it to true when CONFIG_BOUNCE_BUFFER is set. Given that we
have a number of other fields here we had been explicitly setting to
zero, change to first calling memset to clear the struct and then
initialize only the fields that need non-zero default values.
Addresses-Coverity-ID: 467407 ("Uninitialized variables (UNINIT)")
Fixes: 81bd22e935 ("rockchip: block: blk-uclass: add bounce buffer flag to blk_desc")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Extend the otp driver to read rv1126 otp. This driver code was
adapted from the Rockchip BSP stack.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The migration deadline for moving to DM_SCSI was v2023.04. A further
reminder was sent out in August 2023 to the remaining platforms that had
not migrated already, and that a few more over the line (or configs
deleted).
With this commit we:
- Rename CONFIG_DM_SCSI to CONFIG_SCSI.
- Remove all of the non-DM SCSI code. This includes removing other
legacy symbols and code and removes some legacy non-DM AHCI code.
- Some platforms that had previously been DM_SCSI=y && SCSI=n are now
fully migrated to DM_SCSI as a few corner cases in the code assumed
DM_SCSI=y meant SCSI=y.
Signed-off-by: Tom Rini <trini@konsulko.com>
This file uses errno return values in functions, so include <errno.h>
here rather than rely on indirect inclusion.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that sandbox has <asm/barrier.h> and defines nop() there we should
include that in our driver for clarity and then remove our local nop()
from <k210/pll.h>.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Much of the functionality of fastboot relies on being able to run
commands as defined in the environment. This means it does depend on
CMDLINE being enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
While it is nice to have the font command, using 'select' makes it
impossible to build the console code without it. Stop using 'select' and
make it default if CONSOLE_TRUETYPE is enabled when asking the command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to do a DFU update over TFTP we need to have some network
device available, so make this depend on NETDEVICES
Signed-off-by: Tom Rini <trini@konsulko.com>
The following patch migrates the usage of debug and printf functions
to the relevant logging function as per U-Boot DM guidelines.
Additionally some of the debugging statements have been rearanged for
a more meaningfull debug experience.
aarch64-linux-gnu-size reports 229 bytes less when debug is enabled at
file level, while is just 5bytes more when disabled.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@amd.com>
Link: https://lore.kernel.org/r/20231013123739.2757979-1-ibai.erkiaga-elorza@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When 64-bit address is passed only lower 32-bit address
is getting updated. Program the upper 32-bit address in the
DMA destination memory address MSBs register.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231011031515.4151-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Unhandled error coming from xilinx_pm_request() but return
value is not read back that's why getting sparse warning
as below:
warning: variable 'ret' set but not used [-Wunused-but-set-variable].
In case of error return the "ret" value.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231011025647.17200-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Provide an explicit configuration option to disable default "lock"
of any flash chip which supports locking. By disabling the lock
config will save some amount of memory and also don't expose the
lock functionality to the users i.e., via sf protect command.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231003031715.5343-2-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The baudrate configured in .config is taken by default by serial. If
change of baudrate is required then the .config needs to changed and
u-boot recompilation is required or the u-boot environment needs to be
updated.
To avoid this, support is added to fetch the baudrate directly from the
device tree file and update.
The serial, prints the log with the configured baudrate in the dtb.
The commit c4df0f6f31 ("arm: mvebu: Espressobin: Set default value for
$fdtfile env variable") is taken as reference for changing the default
environment variable.
The default environment stores the default baudrate value, When default
baudrate and dtb baudrate are not same glitches are seen on the serial.
So, the environment also needs to be updated with the dtb baudrate to
avoid the glitches on the serial.
Also add test to cover this new function.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230921112043.3144726-3-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Move the DEFAULT_ENV_IS_RW to Kconfig for easier configuration.
Hence, add the CONFIG_DEFAULT_ENV_IS_RW config to the defconfig files
to allow enabling them for armada boards.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921112043.3144726-2-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- sm fix to bind child sm devices in the device tree
- add missing A1 clocks for USB stack
-----BEGIN PGP SIGNATURE-----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=qtcH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20231106' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- fixup to also enabled DFU RAM boot for libretech-ac
- sm fix to bind child sm devices in the device tree
- add missing A1 clocks for USB stack
One well-known sm child device that provides secure power control is the
Secure Power Controller. This device utilizes SMC calls to communicate
with power domains on the secure monitor side.
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231101140500.9025-3-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Since we sync device tree with Linux, we have to add this
clock definition for USB stack.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231101140500.9025-2-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Older DesignWare Ethernet MAC versions that this driver supports can
only work with 32-bit DMA source/destination addresses. Some platforms
have no physical RAM at the lowest 4GB address space. For these
platforms the driver must translate DMA addresses to/from physical
memory addresses.
Call translation routines so that properly configured platforms can use
the DesignWare Ethernet MAC. For platforms using device-tree this
usually means adding dma-ranges property to the bus the device node is
in.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
e1000_eth_ids holds compatible strings for e1000 devices, but it
is meaningless as e1000 is a PCI device and there is no such
compatible string assigned to e1000 by the DT bindings community.
Drop it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Setting the clock delay from the device tree settings
rx-internal-delay-ps and tx-internal-delay-ps was broken:
- The expected value in the device tree is suppose to be a
delay in picoseconds, but the driver only allowed an array index.
- Driver converted this array index to the actual delay in
picoseconds and tried to apply this in the device register. This
however is not a valid register value. The actual logic here was
reversed, it converted an register representation of the delay to
the device tree delay in picoseconds.
Only when the internal delays were NOT configured in the device tree
and they default value of 7 (=2000ps) was used, a valid value was
loaded in the register.
Signed-off-by: Frank de Brabander <debrabander@gmail.com>
It adds the driver for the internal MDIO bus of HIFEMAC Ethernet
controller. It's based on the mainstream linux driver.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
It adds the driver for HIFEMAC Ethernet controller found on HiSilicon
SoCs like Hi3798MV200. It's based on the mainstream linux driver, but
quite a lot of code gets rewritten and cleaned up to adopt u-boot driver
model.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Marvell LinkStreet switches support Clause 45 MDIO on the internal bus.
C45 read or writes require the register address to be written first to
the SMI PHY Data register, and then a special C45 Write Address Register
OP is used on the SMI PHY Register before making a C45 Read Data Register
OP and being able to actually read the register.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Driver is currently defining the mask and bit shifting itself,
there is no need for that as U-Boot has generic bitfield macros that help
us achieve the same result but in a cleaner way.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Add optional reset control, especially for the Aspeed SOC. For the
hardware without a reset line, the reset assertion/deassertion will be
skipped.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Set upper 32bit address for DMA descriptors and buffer address to support
64-bit addressing.
Signed-off-by: Ley Foon Tan <leyfoon.tan@starfivetech.com>
PALMAS PMIC family has embedded poweroff function used by some
device to initiane device power off. Implement it as sysreset
driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TPS65910/TPS65911 PMICs have embedded power control functions
used by some device to initiane device power off. Implement it as
sysreset driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TPS80031/TPS80032 PMICs have embedded power control functions
used by some device to initiane device power off. Implement it as
sysreset driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
MAX77663 PMIC has embedded poweroff function used by some
device to initiane device power off. Implement it as sysreset
driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Tegra uses built in Power Management Controller (PMC) to perform
CPU reset. Code to perform this was located in mach-tegra, so lest
create DM driver to handle this.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The driver provides regulator set/get voltage enable/disable
functions for TI TPS5911 PMIC.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The driver provides regulator set/get voltage enable/disable
functions for TI TPS80031/TPS80032 PMICs.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
dev->driver_data will carry the tail of ldo if there is a number and
if there is no number it will be an error code, anyway it will not be
zero. This results in a wrong ldo regulator detection.
To avoid this check for non-numerical ldo first and then manipulate
dev->driver_data.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Existing PALMAS PMIC driver is fully compatible with TI TPS65913
PMIC found in many Tegra 4 devices, like Tegra Note 7 and ASUS
TF701T. TPS65913 shares same structure of regulators like TPS659038
so data can be reused.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # NVIDIA Tegratab
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Default-tap and default-trim values are used for eMMC setup
mostly on T114+ devices. As for now, those values are hardcoded
for T210 and ignored for all other Tegra generations. Fix this
by passing tap and trim values from dts.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
on Peach-pi console every key press is echoed with message
'cros_ec_command: Returned status 1'
this is not proper fix, just hack to disable this message
Signed-off-by: Milan P. Stanić <mps@arvanta.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
i2c updates for v2024.01-rc2
- nuvoton: support standard/fast/fast plus mode
- bootcount: remove legacy i2c driver and implement
DM based version
Bugfixes:
- designware_i2c: adjust timing calculation
SPL probing failed on the StarFive VisionFive 2 board
Heinrich fixed this, by syncing timing calculation with
linux implementation.
+ CI: Use OpenSBI 1.3.1 release for testing
+ riscv: Support resume after exception
+ rng: Support RNG provided by RISC-V Zkr ISA extension
+ board: starfive VF2: Support jtag
+ board: starfive VF2: Support TRNG driver
+ board: sifive unmatched: Move kernel load address
In line with changes elsewhere, drop inclusion of the common header.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Adds to support JH7110 TRNG driver which is based on linux kernel's
jh7110-trng.c. This can support to generate 256-bit random numbers and
128-bit but this makes 256-bit default for convenience.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add STGCLK_SEC_HCLK and STGCLK_SEC_MISCAHB clocks for JH7110 TRNG
device.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The Zkr ISA extension (ratified Nov 2021) introduced the seed CSR. It
provides an interface to a physical entropy source.
A RNG driver based on the seed CSR is provided. It depends on
mseccfg.sseed being set in the SBI firmware.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This contains several fixes for the clock core.
-----BEGIN PGP SIGNATURE-----
iQGTBAABCgB9FiEEkGEdW86NSNID6GAoPuiP7LShEG4FAmVCut1fFIAAAAAALgAo
aXNzdWVyLWZwckBub3RhdGlvbnMub3BlbnBncC5maWZ0aGhvcnNlbWFuLm5ldDkw
NjExRDVCQ0U4RDQ4RDIwM0U4NjAyODNFRTg4RkVDQjRBMTEwNkUACgkQPuiP7LSh
EG5TAgf+MtLNjT+HWQAXTNMqC/ey/I0vp/Zo4uU6+tNbs05BbEcInAavoT42Sf2Y
HMWiviG96wZrN0J5UH+pXzVAh2nrhEXzYX1L054EsJ/R8lHMKvmcxDW/HYoaLeaY
9A1AseptbJc3UiEtejfUmuBFYdMoLZc+wmqT7iO9yxFFhoBpD9CiSQQVKkcKoI56
3YKLsTwC4yyTrNr95EM/wILfHu6NOh1cn8fQloVIWD1bGR7qLs7ORcdpbR3Plde3
iFeTHbJby2cHEn8j84axzs9sqFcc5ZcKXZJ7tKVhu04pjbqHezMOZe9r/vf38NfZ
6Rf4s4kqRQZKxLBM9ADg/2ocNqEFKA==
=QToO
-----END PGP SIGNATURE-----
Merge tag 'clk-2024.01-rc2' of https://source.denx.de/u-boot/custodians/u-boot-clk
Clock changes for 2024.01-rc2
This contains several fixes for the clock core.
In clk_enable()/clk_disable() functions, when CCF is activated,
we must pass a private clk struct to enable()/disable() ops functions.
Otherwise, the use of a container_of() construction within these ops
should be banned. Because passing a non-private clk struct to
container_of() results in an out of range error.
At the moment, clk-mux, clk-fixed-factor, clk-gate and possibly other
clocks use container_of() in their enable()/disable() functions.
Therefore, for these functions to work correclty, private clk struct
must be passed.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20230905221649.3577929-1-bigunclemax@gmail.com
The second parameter for clk_release_all is used as an unsigned
(which makes sense) but the function prototype declares it as an int.
This causes warnings/error like such below:
include/clk.h:422:48: error: conversion to ‘int’ from ‘unsigned int’ may change the sign of the result [-Werror=sign-conversion]
422 | return clk_release_all(bulk->clks, bulk->count);
To fix this, changed the type of the count to `unsigned int`
Fixes: 82a8a669b4 ("clk: add clk_release_all()")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20230619104752.278500-1-eugen.hristev@collabora.com
In commit 5c5992cb90 ("clk: Add debugging for return values"), a
temporary storage variable was added around the ops->get_rate() call
inside clk_get_rate(), so that the result could be passed through
log_ret.
This temporary variable was declared as an int, yet when we look in
struct clk_ops, we can see this needs to be a ulong:
ulong (*get_rate)(struct clk *clk);
This was resulting in a signed to unsigned casting error on our
builds, where a clock value of 0xABCDABCD was being incorrectly cast
to 0xFFFFFFFFABCDABCD.
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20230515195005.1961495-1-nathan.morrison@timesys.com
Compiling sandbox_defconfig with CONFIG_BOOTSTD=n fails:
/usr/bin/ld: drivers/mtd/spi/sf_bootdev.o:
in function `sf_get_bootflow':
/drivers/mtd/spi/sf_bootdev.c:43:(.text+0x96):
undefined reference to `bootmeth_set_bootflow'
Add the missing Kconfig dependency.
Fixes: Fixes: 0c1f4a9fb1 ("bootstd: Add a SPI flash bootdev")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As noted in commit 3a6383207b ("mmc: sdhci: add the quirk for broken
r1b response"), some MMC controllers don't always set the transfer
complete bit with R1b responses.
According to the SD Host Controller Simplified Specification v4.20,
> In the case of a command pairing with response-with-busy[, Transfer
> Complete] is set when busy is de-asserted. Refer to DAT Line Active
> and Command Inhibit (DAT) in the Present State register.
By polling the DAT Line Active bit in the present state register, we can
detect when we are no longer busy, without waiting for a long timeout.
This results in much faster reads/writes on buggy controllers.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Tested-by: Henrik Grimler <henrik@grimler.se>
dm_pci_map_bar() return a value of (void *) already, hence no need
to cast it again before assigning to host->ioaddr.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
mmc_bind() in mmc-uclass.c calls blk_create_devicef() which is
defined in blk-uclass.c, so SPL_BLK is required by SPL_DM_MMC.
Implicitly select SPL_BLK for SPL_DM_MMC.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
PLL calibration needs to be enabled when operating in non fractional
mode. Add the sequence to do a fast calibration when using PLL
in this mode.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Add support for exposing the whole mmc device by setting the 'size'
parameter to 0. This can be useful in case it is not clear what the
total device size is up front. Update the documentation accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Link: https://lore.kernel.org/r/20231029223740.284149-1-marex@denx.de
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This adds a generic I2C bootcounter adhering to driver model to replace
the previously removed legacy implementation.
There is no change in functionality, it can be used on any I2C device.
The device tree configuration may look like this for example:
bootcount {
compatible = "u-boot,bootcount-i2c";
i2cbcdev = <&i2c_rtc>;
offset = <0x11>;
};
Signed-off-by: Philip Richard Oberfichtner <pro@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
This new function enhances the i2c_get_chip*() toolbox by implementing a
variant that does not require a chip_addr. Instead, the desired device
is pointed to by a phandle.
Signed-off-by: Philip Richard Oberfichtner <pro@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
The legacy I2C bootcounter will hereby be removed and eventually
be replaced by a driver model implementation in the follow-up commit.
The legacy driver has the following drawbacks:
- It's not adhering to the driver model
- Settings are grabbed from Kconfig rather than device tree
- i2c_{read,write} are being used instead of dm_i2c_{read,write}
Signed-off-by: Philip Richard Oberfichtner <pro@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Calculate the maximum length of the buffer when writing
across the page boundary. If the buffer length (len)
exceeds the page boundary (pagesize), split it. Use this
length instead of comparing the length with the pagesize,
because if the write start address (offset) is not at the
beginning of a page and the page_offset + len is greater
than the page boundary (pagesize), the write operation
would overflow the current page and the behaviour can be
undefined (e.g. at24).
Signed-off-by: Alex Michel <alex.michel@wiedemann-group.com>
Similar change was done by commit b4c2c151b1 ("Kconfig: Remove all
default n/no options") and again sync is required.
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com> # tegra
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@kernel-space.org>
In SPL probing of the designware_i2c device on the StarFive VisionFive 2
board fails with
dw_i2c: mode 0, ic_clk 1000000, speed 100000,
period 10 rise 1 fall 1 tlow 5 thigh 4 spk 0
dw_i2c: bad counts. hcnt = -4 lcnt = 4
device_probe: i2c@12050000 failed to probe -22
When changing the offset for the high phase from 7 to 3 the device is
probed correctly. This now matches the value from the Linux driver.
Without this fix the memory size of the StarFive VisionFive 2 board cannot
be read from EEPROM.
Fixes: e71b6f6622 ("i2c: designware_i2c: Rewrite timing calculation")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
first version is only support standard mode.
remove this judgment to support standard/fast/fast plus mode.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Changes for v2:
- add commit message
Reviewed-by: Heiko Schocher <hs@denx.de>
To avoid thermal burn out, program thermal shutdown
value in VTM (Voltage and Thermal Manager) IP.
Part of Linux kernel driver (drivers/thermal/k3_j72xx_bandgap.c)
is ported from kernel 6.6-rc1, which sets thermal shutdown values.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Neha Francis <n-francis@ti.com>
In current vexpress_config_probe code, it sets the uclass private data
directly. This will cause one compilation error:
drivers/misc/vexpress_config.c:114:27: error: lvalue required as left operand of assignment
114 | dev_get_uclass_priv(dev) = priv;
| ^
In this patch we set the uclass private data through struct member
.priv_auto, and this compilation error disappears.
Signed-off-by: Wei Chen <wei.chen@arm.com>
Signed-off-by: Qi Feng <qi.feng@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEgWII69YpahbL5iK5gS8AYozs+qIFAmU7j50ACgkQgS8AYozs
+qIh8w/+O4UjT0sG1NLwmyV7U1Ypk+EyYaE6wmSWzpsJLfH/YvtObBJOYRuXxRVh
J9lkgCsw8Ct1ZNCrp8iVO+Dz1DtV8+QvTecrUHZqcOhTYDaqxXnlvEH2/EUhgo5T
9a/ZaDtOP1mKz754C4G6G363+iRCvbcqDECeKg9VYxfWCo1cINOmqyQCqlGxFT+h
PKiB5VzUpN/K/yiie+Hr42/+6XaykAUjUvEWeyKOsRmYY4lNiK22vG/puE42bFTh
catXwTE2a7x+yzPKkdhR0UGvDUlIKET2kF6mi+pYN2h/cSUxWTzbP/OxcU9yJOnm
qJiRZ+Woez1I7ul6ln4ci2kiWc3CTYFXfctwrBJPuJ/EO+2EEb3oHqG2S3Fc9VBZ
N17flHW7XZHEQbNexlUhk9cRpCwRuSA5OJXwW+IZIuydgNeo3xF0iYvipbjkEGgW
BBkt8PH+ivTLjEz6Gcmquvo1fHGJLHRIPg7DNb0phGHviuC0zlDJ7N5DZk0CpkiT
36siV9xK4X6qvWkOTa6Ldw60e4tN9nv3VG30uXtPHi3XdOkKfNkyIuqO/5BkkQPt
6yEc9IYXYoWNKDVUGme5+xszZp1sSvqltajG9VVNupt958dFyOSgS5aNa6B4UsWX
3XfndP1/s2bezUHoQx5zjraapKVrqBFLkGeTlCDUD+mEgP440G8=
=gvDs
-----END PGP SIGNATURE-----
Merge tag 'tpm-next-27102023' of https://source.denx.de/u-boot/custodians/u-boot-tpm
bootX measurements and measurement API moved to u-boot core:
Up to now, U-Boot could perform measurements and EventLog creation as
described by the TCG spec when booting via EFI.
The EFI code was residing in lib/efi_loader/efi_tcg2.c and contained
both EFI specific code + the API needed to access the TPM, extend PCRs
and create an EventLog. The non-EFI part proved modular enough and
moving it around to the TPM subsystem was straightforward.
With that in place we can have a common API for measuring binaries
regardless of the boot command, EFI or boot(m|i|z), and contructing an
EventLog.
I've tested all of the EFI cases -- booting with an empty EventLog and
booting with a previous stage loader providing one and found no
regressions. Eddie tested the bootX part.
Eddie also fixed the sandbox TPM which couldn't be used for the EFI code
and it now supports all the required capabilities. This had a slight
sideeffect in our testing since the EFI subsystem initializes the TPM
early and 'tpm2 init' failed during some python tests. That code only
opens the device though, so we can replace it with 'tpm2 autostart'
which doesn't error out and still allows you to perfom the rest of the
tests but doesn't report an error if the device is already opened.
There's a few minor issues with this PR as well but since testing and
verifying the changes takes a considerable amount of time, I prefer
merging it now.
Heinrich has already sent a PR for -master containing "efi_loader: fix
EFI_ENTRY point on get_active_pcr_banks" and I am not sure if that will
cause any conflicts, but in any case they should be trivial to resolve.
Both the EFI and non-EFI code have a Kconfig for measuring the loaded
Device Tree. The reason this is optional is that we can't reason
when/if devices add random info like kaslr-seed, mac addresses etc in
the DT. In that case measurements are random, board specific and
eventually useless. The reason it was difficult to fix it prior to this
patchset is because the EFI subsystem and thus measurements was brought
up late and DT fixups might have already been applied. With this
patchset we can measure the DT really early in the future.
Heinrich also pointed out that the two Kconfigs for the DTB measurements
can be squashed in a single one and that the documentation only explains
the non-EFI case. I agree on both but as I said this is a sane working
version, so let's pull this first it's aleady big enough and painful to
test.
Add A1 SPIFC driver from Linux. Slightly modified to use u-boot driver
framework and accommodate to lack of ioread32_rep/iowrite32_rep.
Based on Linux version 6.6-rc4
Signed-off-by: Igor Prusov <IVPrusov@sberdevices.ru>
Signed-off-by: Martin Kurbanov <mmkurbanov@sberdevices.ru>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20231024225140.366571-2-ivprusov@sberdevices.ru
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
[trini: Drop <common.h> as it's not needed]
The driver needs to support getting the PCRs in the capabilities
command. Fix various other things and support the max number
of PCRs for TPM2.
Remove the !SANDBOX dependency for EFI TCG2 as well.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The R-Car Gen3 SD_CLK_CTRL register does not use BIT(16) to implement
divider 1/1024, instead BIT(16) is reserved bit and divider 1/1024 is
not supported. The divider 1/1024 is specific to Socionext variant of
the IP, as is indicated by Linux commit:
0196c8db8363 ("mmc: tmio: move tmio_mmc_set_clock() to platform hook")
"
Socionext (and Panasonic) uses bit 10 (CLKSEL) for 1/1. Also, newer
versions of UniPhier SoC variants use bit 16 for 1/1024.
"
Do not set the TMIO_SD_CAP_DIV1024 on Renesas R-Car platforms even if
the IP VERSION register does exist, and indicates IP version is newer
or equal to version 1.0 . The IP version 1.0 or newer does not imply
presence of the 1/1024 divider.
Since the TMIO driver is used exactly by two supported platforms, that
is Renesas R-Car and Socionext UniPhier, it is OK to check whether the
TMIO_SD_CAP_RCAR capability is not set to identify the UniPhier platform
and add the capability only on that platform.
Fixes: 58c35b17aa ("mmc: matsushita-common: Always check controller version")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Thuan Nguyen Hong <thuan.nguyen-hong@banvien.com.vn>
Unconditionally check for errors even after successful reception
of IRQ flag, since the hardware may set both an IRQ completion
flag and an error flag at the same time.
This mode of failure happens in case of an error during transfer,
in which case the hardware may set the expected IRQ completion
flag as well as error flags. The later is currently not checked
by the driver and such an error is not detected. Improve the
error detection.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Thuan Nguyen Hong <thuan.nguyen-hong@banvien.com.vn>
This driver is long superseded by renesas-sdhi.c and unused.
Drop the driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Paul Barker <paul.barker.ct@bp.renesas.com>
We should ensure that reset_free() is called in the error path.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Fixes: 93c811b733 ("mmc: renesas-sdhi: Initialize module on RZ/G2L")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
When debugging, one sometimes only gets partial output lines or
nothing at all from the last printf, because the uart has a largish
buffer, and the code after the printf() may cause the CPU to hang
before the uart IP has time to actually emit all the characters. That
can be very confusing, because one doesn't then know exactly where the
hang happens.
Introduce a config knob allowing one to wait for the uart fifo to
drain whenever a newline character is printed, roughly corresponding
to the effect of setvbuf(..., _IOLBF, ...) in ordinary C programs.
Since this uses IS_ENABLED() instead of cpp ifdef, we can remove the
ifdef around the _serial_flush() definition - if neither
CONSOLE_FLUSH_SUPPORT or CONSOLE_FLUSH_ON_NEWLINE are enabled, the
compiler elides _serial_flush(), but it won't warn about it being
unused.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
SCMI power domain management protocol is supported on sandbox
for test purpose. Add fake agent interfaces and associated
power domain devices.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
In this patch, added are helper functions to directly manipulate
SCMI power domain management protocol. DM compliant power domain
driver will be implemented on top of those interfaces in a succeeding
patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
- Add Board: rk3588 NanoPC-T6, Orange Pi 5, Orange Pi 5 Plus;
- clk driver fix for rk3568 and rk3588;
- rkmtd cmd support for rockchip nand device;
- dts update and sync from linux;
Currently bounce buffer support is enabled for all block devices
when available. Add a flag to blk_desc to enable only on demand.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add rkmtd class and drivers to create a virtual block device
to transfer Rockchip boot block data to and from NAND with
block orientated tools like "ums" and "rockusb".
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Prepare a rkmtd UCLASS in use for writing Rockchip boot blocks
in combination with existing userspace tools and rockusb command.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On Rockchip SoCs the first boot stages are written on NAND
with help of manufacturer software that uses a different format
then the MTD framework. Skip the automatic BBT scan with the
NAND_SKIP_BBTSCAN option to be able to pass the driver probe
function and to let the original data unchanged.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for XMC XM25QU128C (128M-bit) Serial Flash memory. Used on
the Xunlong Orange Pi 3B, 5 and 5 Plus boards.
Datasheet:
https://www.xmcwh.com/uploads/806/XM25QU128C_Ver2.0.pdf
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
[jonas@kwiboo.se: update commit message]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
It's normal to have no SATA drive attached to the controller, so return a
successful status when there is no block device found after probing.
Note: this patch depends on the previous patch
https://patchwork.ozlabs.org/project/uboot/patch/20230917230649.30357-1-mibodhi@gmail.com/
Resend the right patch.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add ahci sata bootdev and corresponding hunting function.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is mostly about support for the Allwinner R528/T113s SoC, which is
reportedly the same die as the Allwinner D1, but with the two
Arm Cortex-A7 cores activated instead of the RISC-V one.
Using sunxi code outside of arch/arm proved to be difficult, so apart
from enabling this Arm SoC, the patches also prepare for more refactoring
to get the D1 nicely supported some day:
- We get rid of some Kconfig (hard-)coded GPIO pins, responsible for
enabling regulators.
- The GPIO code is moved out of arch/arm, into drivers/gpio.
- Some definitions are moved out of header files under asm/arch.
- Some T113s/D1 specific definitions are guarded by a generic Kconfig
symbol (CONFIG_SUNXI_GEN_NCAT2).
- The DRAM controller initialisation code is located under drivers/ram.
- The base SoC .dtsi files are shared (under arch/riscv, as in Linux).
Of course there are also the usual new SoC specific patches, like clock
and pinmux descriptions, alongside a rework of the pinctrl code, since
Allwinner changed the GPIO register layout, for the first time since
sunxi's inception.
On top of this the PSCI code sees some update, to provide SMP services
for R528/T113s boards. Many thanks to Sam for providing this code and
staying strong through the review cycles.
The final patch enables support for one popular board, I hope to see
more DTs and defconfigs contributed in the future!
Many thanks to all the various contributors, testers and reviewers,
that series was a real team effort!
fixed/gpio regulator counter in balance
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZTY2dA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXDi0AJ0aJC4GlmmHtbmzBJdarGrb72zBtgCdGbzQaNj6
88xzVixBqtJPbJXGxKg=
=yCjQ
-----END PGP SIGNATURE-----
Merge tag 'video-20231022' of https://source.denx.de/u-boot/custodians/u-boot-video
- updates for pwm_backlight, simple_panel and tegra20 to keep
fixed/gpio regulator counter in balance
rk3588 frac pll:
FFVCO = ((m + k / 65536) * FFIN) / p
FFOUT = ((m + k / 65536) * FFIN) / (p * 2s)
k is the original code, but the K[15:0] is complement code
(6'b1000_0000_0000_0000 <= K[15:0] <= 16'b0111_1111_1111_1111),
need to be converted.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
aclk_top_root choose a parent clock that does not change.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For a specific frequency.
Signed-off-by: Guochun Huang <hero.huang@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This adds the remaining code bits to teach U-Boot about Allwinner's
newest SoC generation. This was introduced with the RISC-V based
Allwinner D1 SoC, which actually shares a die with the ARM cores versions
called R528 (BGA, without DRAM) and T113s (QFP, with embedded DRAM).
This adds the new Kconfig stanza, using the two newly introduced symbols
for the new SoC generation and pincontroller. It also adds the new symbols
to the relavent code places, to set all the hardcoded bits directly.
We need one DT override:
The ARM core version of the DT specifies the CPUX watchdog as
"reserved", which means it won't be recognised by U-Boot. Override this
in our generic sunxi-u-boot.dtsi, to let U-Boot pick up this watchdog,
so that the generic reset driver will work.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Allwinner R528/T113-s/D1/D1s SoCs all share the same die, so use the
same DRAM initialisation code.
Make use of prior art here and lift some code from awboot[1], which
carried init code based on earlier decompilation efforts, but with a
GPL2 license tag.
This code has been heavily reworked and cleaned up, to match previous
DRAM routines for other SoCs, and also to be closer to U-Boot's coding
style and support routines.
The actual DRAM chip timing parameters are included in the main file,
since they cover all DRAM types, and are protected by a new Kconfig
CONFIG_SUNXI_DRAM_TYPE symbol, which allows the compiler to pick only
the relevant settings, at build time.
The relevant DRAM chips/board specific configuration parameters are
delivered via Kconfig, so this code here should work for all supported
SoCs and DRAM chips combinations.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Sam Edwards <CFSworks@gmail.com>
At the moment all Allwinner DRAM initialisation routines are stored in
arch/arm/mach-sunxi, even though those "drivers" are just a giant
collection of writel's, without any architectural dependency.
The R528/T113-s SoC (with ARM cores) and the D1/D1s Soc (with RISC-V
cores) share the same die, so should share the same DRAM init routines as
well.
To prepare for this, add a new sunxi directory inside drivers/ram, and
add some stub entries to prepare for the addition of the share DRAM code
for those SoCs.
The RISC-V D1(s) SoCs will probably use SPL_DM, so for that SoC this
would be the right directory anyway.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since the D1 CCU binding is defined, we can add support for its
gates/resets, following the pattern of the existing drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Apart from using the new pinctrl MMIO register layout, the Allwinner D1
and related SoCs still need to usual set of mux values hardcoded in
U-Boot's pinctrl driver.
Add the values we need so far to this list, so that DM based drivers
will just work without further ado.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Allwinner seems to typically stick to a common MMIO memory map for
several SoCs, but from time to time does some breaking changes, which
also introduce new generations of some peripherals. The last time this
happened with the H6, which apart from re-organising the base addresses
also changed the clock controller significantly. We added a
CONFIG_SUN50I_GEN_H6 symbol back then to mark SoCs sharing those traits.
Now the Allwinner D1 changes the memory map again, and also extends the
pincontroller, among other peripherals.
To mark this generation of SoCs, add a CONFIG_SUNXI_GEN_NCAT2 symbol,
this name is reportedly used in the Allwinner BSP code, and prevents us
from inventing our own name.
Add this new symbol to some guards that were already checking for the H6
generation, since many features are shared between the two (like the
renovated clock controller).
This paves the way to introduce a first user of this generation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org>
For the first time since at least the Allwinner A10 SoCs, the D1 (and
related cores) use a new pincontroller MMIO register layout, so we
cannot use our hardcoded, fixed offsets anymore.
Ideally this would all be handled by devicetree and DM drivers, but for
the DT-less SPL we still need the legacy interfaces.
Add a new Kconfig symbol to differenciate between the two generations of
pincontrollers, and just use that to just switch some basic symbols.
The rest is already abstracted enough, so works out of the box.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
Tested-by: Sam Edwards <CFSworks@gmail.com>
Tested-by: Samuel Holland <samuel@sholland.org>
U-Boot's generic GPIO_EXTRA_HEADER is a convenience symbol to allow code
to more easily include platform specific GPIO headers. This should not
be needed in a DM world anymore, since the generic GPIO framework
handles that nicely.
For Allwinner boards we still need to deal with non-DM GPIO in the SPL,
but this should become the exception, not the rule.
Make this more obvious by removing the definition of GPIO_EXTRA_HEADER,
and just force every legacy user of platform specific GPIO to include
the new sunxi_gpio.h header explicitly. Everyone doing so should feel
ashamed and should find a way to avoid it from now on.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org>
So far every Allwinner SoC used the same basic pincontroller/GPIO
register frame, and just differed by the number of implemented banks and
pins, plus some special functionality from time to time. However the D1
and successors use a slightly different pinctrl register layout.
Use that opportunity to drop "struct sunxi_gpio", that described that
MMIO frame in a C struct. That approach is somewhat frowned upon in the
Linux world and rarely used there, though still popular with U-Boot.
Switching from a C struct to a "base address plus offset" approach allows
to switch between the two models more dynamically, without reverting to
preprocessor macros and #ifdef's.
Model the pinctrl MMIO register frame in the usual "base address +
offset" way, and replace a hard-to-parse CPP macro with a more readable
static function.
All the users get converted over. There are no functional changes at
this point, it just prepares the stages for the D1 and friends.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
So far we were open-coding the pincontroller's GPIO output/input access
in each function using that.
Provide functions that wrap that nicely, and follow the existing pattern
(set/get_{bank,}), so users don't need to know about the internals, and
we can abstract the new D1 pinctrl more easily.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Move the existing sunxi-specific low level pinctrl routines from
arch/arm/mach-sunxi into the existing GPIO code under drivers/gpio, so
that the common code can be shared outside of arch/arm.
This also takes the opportunity to move some definitions from our
header file into the driver C file, as they are private to the driver
and are not needed elsewhere.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
The CONFIG_MACPWR Kconfig symbol is used to point to a GPIO that enables
the power for the Ethernet "MAC" (mostly PHY, really).
In the DT this is described with the phy-supply property in the MAC DT
node, pointing to a (GPIO controlled) regulator. Since we need Ethernet
only in U-Boot proper, and use a DM driver there, we should use the DT
instead of hardcoding this.
Add code to the sun8i_emac and sunxi_emac drivers to check the DT for
that regulator and enable it, at probe time. Then drop the current code
from board.c, which was doing that job before.
This allows us to remove the MACPWR Kconfig definition and the respective
values from the defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
At the moment the sun4i EMAC driver relies on hardcoded CONFIG_MACPWR
Kconfig symbols to enable potential PHY regulators. As we want to get rid
of those, we need to find the regulator by chasing up the DT.
The sun4i-emac binding puts the PHY regulator into the MDIO node, which
is the parent of the PHY device. U-Boot does not have (and does not
need) an MDIO driver, so we need to chase down the regulator through the
EMAC node: we follow the "phy-handle" property to find the PHY node,
then go up to its parent, where we find the "phy-supply" link to the
regulator. Let U-Boot find the associated regulator device, and put that
into the private device struct, so we can find and enable the regulator
at probe time, later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
The CONFIG_SATAPWR Kconfig symbol was used to point to a GPIO that
enables the power for a SATA harddisk.
In the DT this is described with the target-supply property in the AHCI
DT node, pointing to a (GPIO controlled) regulator. Since we need SATA
only in U-Boot proper, and use a DM driver for AHCI there, we should use
the DT instead of hardcoding this.
Add code to the sunxi AHCI driver to check the DT for that regulator and
enable it, at probe time. Then drop the current code from board.c, which
was doing that job before.
This allows us to remove the SATAPWR Kconfig definition and the
respective values from the defconfigs.
We also select the generic fixed regulator driver, which handles those
GPIO controlled regulators.
Please note that the OrangePi Plus is a bit special here, it's a H3
board without native SATA, but with a USB-to-SATA bridge. The DT models
the SATA power via a VBUS supply regulator, which we don't parse yet in
the USB PHY driver. Use the hardcoded CONFIG_USB3_VBUS_PIN for that
board meanwhile.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators and may be further expanded on all
regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators and may be further expanded on all
regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators and may be further expanded on all
regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Extend the existing driver to support the SCIF serial ports on the
Renesas RZ/G2L (R9A07G044) SoC. This also requires us to ensure that if
there is a reset signal defined in the device tree, it is de-asserted
before we try to talk to the SCIF module.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # R-Car H3 Salvator-XS
The current SCIF error handling is broken for the RZ/G2L. After a break
condition has been triggered, the current code is unable to clear the
error and serial port output never resumes.
The RZ/G2L datasheet says that most error conditions are cleared by
resetting the relevant error bits in the FSR & LSR registers to zero.
To clear framing errors on SCIF ports, the invalid data also needs to be
read out of the receive FIFO.
After reviewing datasheets for RZ/G2{H,M,N,E}, R-Car Gen4, R-Car Gen3
and even SH7751 SoCs, it's clear that this is the way to clear errors
for all of these SoCs.
While we're here, annotate the handle_error() function with a couple of
comments as the reads and writes themselves don't immediately make it
clear what we're doing.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Tested-by: Chris Paterson <chris.paterson2@renesas.com> # HiHope RZ/G2M board
Tested-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # R-Car H3 Salvator-XS
Fix npcm845 watchdog halt for reset function and expire function.
Reset function is restart wdt.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The ST M24C32-D behaves as a regular M24C32, except for the -D variant
which uses up another I2C address for Additional Write lockable page.
This page is 32 Bytes long and can contain additional data. Add entry
for it, so users can describe that page in DT. Note that users still
have to describe the main M24C32 area separately as that is on separate
I2C address from this page.
From Linux kernel commit:
4791146e9055 ("eeprom: at24: add ST M24C32-D Additional Write lockable page support")
Signed-off-by: Marek Vasut <marex@denx.de>
The i.MX93 11x11 EVK fails to boot with following error:
Model: NXP i.MX93 11X11 EVK board
DRAM: 2 GiB
Error binding driver 'imx93-adc': -96
Some drivers failed to bind
Error binding driver 'simple_bus': -96
Some drivers failed to bind
Error binding driver 'simple_bus': -96
Some drivers failed to bind
initcall sequence 00000000fffb8f28 failed at call 000000008021e0d4 (err=-96)
### ERROR ### Please RESET the board ###
That's because since commit e7ff54d963 ("imx93_evk: defconfig: add adc
support") CONFIG_ADC_IMX93 is enabled but CONFIG_ADC is not.
Fix this by enabling CONFIG_ADC in imx93_11x11_evk_defconfig.
Make sure this situation won't happen again in future i.MX93 defconfig by
making CONFIG_ADC_IMX93 depend on CONFIG_ADC.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Patch which add A1 SoC support create a regression on khadas vim3/vim3l
boards when we try to use fastboot command:
=> fastboot usb 0
failed to get power domain
failed to get power domain
No USB device found
USB init failed: -19
Add ENOENT check on ret in probe function.
Fixes: 5533c883ce ("phy: support Amlogic A1 family")
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on vim3
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231017185725.809524-1-glaroque@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
lib/acpi/acpigen.o is only compiled into SPL when SPL_ACPIGEN is enabled.
Update several files which reference these functions accordingly.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sandbox unit tests in U-Boot proper load a test device tree to have some
devices to work with. In order to do the same in SPL, we must enable
SPL_OF_REAL. However, we already have SPL_OF_PLATDATA enabled. When
generating platdata from a devicetree, it is expected that we will not need
devicetree access functions (even though SPL_OF_CONTROL is enabled). This
expectation does not hold for sandbox, so allow user control of
SPL_OF_REAL.
There are several places in the tree where conditions involving OF_PLATDATA
or OF_REAL no longer function correctly when both of these options can be
selected at the same time. Adjust these conditions accordingly.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make sure we have an IMX header before calling spl_load_imx_container,
since if we don't it will fail with -ENOENT. This allows us to fall back to
legacy/raw images if they are also enabled.
This is a functional change, one which likely should have been in place
from the start, but a functional change nonetheless. Previously, all
non-IMX8 images (except FITs without FIT_FULL) would be optimized out if
the only image load method enabled supported IMX8 images. With this change,
support for other image types now has an effect.
There are seven boards with SPL_LOAD_IMX_CONTAINER enabled: three with
SPL_BOOTROM_SUPPORT:
imx93_11x11_evk_ld imx93_11x11_evk imx8ulp_evk
and four with SPL_MMC:
deneb imx8qxp_mek giedi imx8qm_mek
All of these boards also have SPL_RAW_IMAGE_SUPPORT and
SPL_LEGACY_IMAGE_FORMAT enabled as well. However, none have FIT support
enabled. Of the six load methods affected by this patch, only SPL_MMC and
SPL_BOOTROM_SUPPORT are enabled with SPL_LOAD_IMX_CONTAINER.
spl_romapi_load_image_seekable does not support legacy or raw images, so
there is no growth. However, mmc_load_image_raw_sector does support loading
legacy/raw images. Since these images could not have been booted before, I
have disabled support for legacy/raw images on these four boards. This
reduces bloat from around 800 bytes to around 200.
There are no in-tree boards with SPL_LOAD_IMX_CONTAINER and AHAB_BOOT both
enabled, so we do not need to worry about potentially falling back to
legacy images in a secure boot scenario.
Future work could include merging imx_container.h with imx8image.h, since
they appear to define mostly the same structures.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
On the Renesas RZ/G2L SoC family, we must ensure that the required clock
signals are enabled and the reset signal is de-asserted before we try to
communicate with the SDHI module.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Move the assignment of priv->quirks earlier in the function. This allows
us to drop the quirks local variable and makes it easier to maintain
clean error handling when we add RZ/G2L support in the next patch.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tidy up the existing include list before we add more includes in the
following patch.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This driver adds support for the gpio features of the GPIO/PFC module in
the Renesas RZ/G2L (R9A07G044) SoC.
The new `rzg2l-pfc-gpio` driver is bound to the same device tree node as
the `rzg2l-pfc-pinctrl` driver as the same hardware block provides both
GPIO and pin multiplexing features.
This patch is based on the corresponding Linux v6.5 driver
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This driver adds support for the pinctrl features of the GPIO/PFC module
in the Renesas RZ/G2L (R9A07G044) SoC.
A multi-function `rzg2l-pfc` driver is defined for UCLASS_NOP, which
binds the `rzg2l-pfc-pinctrl` UCLASS_PINCTRL driver dynamically. We also
define common macros and functions for the PFC in <renesas/rzg2l-pfc.h>.
This makes it easy to add an additional UCLASS_GPIO driver for the GPIO
functionality of this module in a follow-up patch.
This patch is based on the corresponding Linux v6.5 driver
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This driver provides clock and reset control for the Renesas R9A07G044L
(RZ/G2L) and R9A07G044C (RZ/G2LC) SoC. It consists of two parts:
* driver code which is applicable to all SoCs in the RZ/G2L family.
* static data describing the clocks and resets which are specific to the
R9A07G044{L,C} SoCs. The identifier r9a07g044 (without a final letter)
is used to indicate that both SoCs are supported.
clk_set_rate() and clk_get_rate() are implemented only for the clocks
that are actually used in u-boot.
The CPG driver is marked with DM_FLAG_PRE_RELOC to ensure that its bind
function is called before the SCIF (serial port) driver is probed. This
is required so that we can de-assert the relevant reset signal during
the serial driver probe function.
This patch is based on the corresponding Linux v6.5 driver
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
If we attempt to compile serial_sh.c for a system which lacks HSCIF
support (e.g. R8A7740), we see the following compilation error:
In file included from drivers/serial/serial_sh.c:20:
drivers/serial/serial_sh.c: In function ‘sh_serial_init_generic’:
drivers/serial/serial_sh.h:429:35: warning: implicit declaration of function ‘sci_HSSRR_out’; did you mean ‘sci_SCSCR_out’? [-Wimplicit-function-declaration]
429 | #define sci_out(port, reg, value) sci_##reg##_out(port, value)
| ^~~~
drivers/serial/serial_sh.c:62:17: note: in expansion of macro ‘sci_out’
62 | sci_out(port, HSSRR, HSSRR_SRE | HSSRR_SRCYC8);
| ^~~~~~~
To fix this, only try to support access to the HSSRR register for SoCs
where it actually exists.
Support for the RZ/G2L will be introduced in following patches, which
selects CONFIG_RCAR_64 but does not have HSCIF interfaces, so check for
CONFIG_RCAR_GEN2 || CONFIG_RCAR_GEN3 || CONFIG_RCAR_GEN4 to determine if
HSCIF is present.
Fixes: bbe36e29ca ('serial: sh: Add HSCIF support for R-Car SoC')
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Cc: Hai Pham <hai.pham.ud@renesas.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Current codes only ennable the PER clock. However on iMX8 the LPUART
also needs IPG clock which is an LPCG. Should not depend on the default
LPCG setting.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Add i.MX93 CCF driver support.
Modifed from Linux Kernel v6.5-rc2 and adapted for U-Boot.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Add hook in sata_mv probe to enable bootstd bootdev.
Note: bootdev_setup_for_sibling_blk() invocation is a noop if bootsd is
not enabled for ahci sata yet.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Since commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable() may be EALREADY or
EBUSY for fixed/GPIO regulators.
Switch to using the more relaxed regulator_set_enable_if_allowed() to
continue if regulator already was enabled or disabled.
This fixes the following error when running the 'ums' command:
=> ums 0 mmc 0
UMS: LUN 0, dev mmc 0, hwpart 0, sector 0x0, count 0xece000
Error enabling VBUS supply
g_dnl_register: failed!, error: -114
g_dnl_register failed
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Use dev_ofnode() to retrieve the USB node pointer from the udevice
structure.
This fixes the following build error:
drivers/usb/host/ehci-mxs.c:143:38: error: 'struct udevice' has no member named 'node_'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
This patch adds an implementation of the Meson Secure Monitor
driver based on UCLASS_SM.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921081346.22157-7-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
At the moment, we don't have a common API for working with
SM, only the smc_call() function. This approach is not generic
and difficult to configure and maintain.
This patch adds UCLASS_SM with the generic API:
- sm_call()
- sm_call_write()
- sm_call_read()
These functions operate with struct pt_regs, which describes
Secure Monitor arguments.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921081346.22157-2-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
scan all entries in multi-device boot_targets
EFI empty-capsule support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmUpvTQRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreabCwgAimB2fGpK3FjFMrH1Ko4Qh3j0D/0XomiQ
1KYVbn3YrswLmq1tav9HSKWR3Ep/Uet6jthpH2RPxhcGWNGqxkkk2k4LUudSlIYd
0KKoovMwBK9jZcojoBAjFGaoRIaEBlbFspW/RoXPJnr7ctxf6HSYkW2TPH09zqtD
FrL5Jjf6t0h6QShxhCYXbiHGCnp2zYZRzFnrYpaXy8IIavqWNJTAhkIGveMy+Qa8
TzhmuRamLgtZZwtFcHt8sZuV4+FtBrtHAyiEasnJFPJ5Kv6tFVBiHdYuygZMu/og
+F57ufgqgHTlDjzW72CJyhrHIcVn/mWjNYrulufqHAsSFD7cizISeA==
=qOUT
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-13oct23' of https://source.denx.de/u-boot/custodians/u-boot-dm
improvements with dev_read_addr_..._ptr()
scan all entries in multi-device boot_targets
EFI empty-capsule support
The sess variable in open_channel was not entirely
cleared to zero at the start of this function.
This commit ensures that the entire struct is cleared.
Signed-off-by: Francois Berder <fberder@outlook.fr>
Now that we have Base protocol support, we will be able to check if a given
protocol is really supported by the SCMI server (firmware).
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
SCMI base protocol is mandatory, and once SCMI node is found in a device
tree, the protocol handle (udevice) is unconditionally installed to
the agent. Then basic information will be retrieved from SCMI server via
the protocol and saved into the agent instance's local storage.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Adding SCMI base protocol makes it inconvenient to hold the agent instance
(udevice) locally since the agent device will be re-created per each test.
Just remove it and simplify the test flows.
The test scenario is not changed at all.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
This is a simple implementation of SCMI base protocol for sandbox.
The main use is in SCMI unit test.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
In SCMI base protocol version 2 (0x20000), new interfaces,
BASE_SET_DEVICE_PERMISSIONS/BASE_SET_PROTOCOL_PERMISSIONS/
BASE_RESET_AGENT_CONFIGURATION, were added. Moreover, the api of
BASE_DISCOVER_AGENT was changed to support self-agent discovery.
So the driver expects SCMI firmware support version 2 of base protocol.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
SCMI base protocol is mandatory according to the SCMI specification.
With this patch, SCMI base protocol can be accessed via SCMI transport
layers. All the commands, except SCMI_BASE_NOTIFY_ERRORS, are supported.
This is because U-Boot doesn't support interrupts and the current transport
layers are not able to handle asynchronous messages properly.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
This framework allows SCMI protocols to be installed and bound to the agent
so that the agent can manage and utilize them later.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Move the location of scmi_bind_protocols() backward for changes
in later patches.
There is no change in functionality.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
In sandbox scmi agent, channels are not used at all. But in this patch,
dummy channels are supported in order to test protocol-specific channels.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
SCMI specification allows any protocol to have its own channel for
the transport. While the current SCMI driver may assign its channel
from a device tree, the core function, devm_scmi_process_msg(), doesn't
use a protocol's channel, but always use an agent's channel.
With this commit, devm_scmi_process_msg() tries to find and use
a protocol's channel. If it doesn't exist, use an agent's.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The commit 85dc582892 ("firmware: scmi: prepare uclass to pass channel
reference") added an explicit parameter, channel, but it seems to make
the code complex.
Hiding this parameter will allow for adding a generic (protocol-agnostic)
helper function, i.e. for PROTOCOL_VERSION, in a later patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
A follow-up to commit 842fb5de42
("drivers: use devfdt_get_addr_size_index_ptr when cast to pointer")
and commit 320a1938b6
("drivers: use devfdt_get_addr_index_ptr when cast to pointer").
In addition to using the *_ptr variants of these functions where the
address is cast to a pointer, this also changes devfdt_get_addr_*() to
dev_read_addr_*() in a few places. Some variable and field types are
changed from fdt_addr_t or phys_addr_t to void* where the cast was
happening later.
This patch fixes a number of compile warnings when building a 32bit
U-Boot with CONFIG_PHYS_64BIT=y. In some places, it also fixes error
handling where the return value of dev_read_addr() etc. was checked for
NULL instead of FDT_ADDR_T_NONE.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
pinctrl-single uses fdt_addr_t and phys_addr_t inconsistently, but both
are wrong to be passed to readb() etc., which expect a pointer or
pointer-sized integer. Change the driver to use
dev_read_addr_size_index_ptr(), so we consistently deal with void*
(except for the sandbox case and single_get_pin_muxing()).
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add missing mapmem.h header:
Signed-off-by: Simon Glass <sjg@chromium.org>
Same as dev_read_addr_name[_size](), but returns a pointer, cast
through map_sysmem().
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Checking for the error cast to fdt_addr_t is rather awkward - IS_ERR()
can be used, but it's not really made to be used on fdt_addr_t, which
may not even be the same size as a native pointer.
Most places in U-Boot only check for FDT_ADDR_T_NONE; let's adjust the
error return to match the expectation.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZSjvwAAKCRDKSWXLKUoM
IR34AJ92oum3pJXKxKREEZh0dCfDvJlE/wCggyzxI2T5liJfRG5jzlUuDjiLLU0=
=u1bz
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.01-rc1-v3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2024.01-rc1 v3
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
In the existing implementation, multiple requests queued up on an
endpoint are subject to getting evicted without transmission.
For both control and bulk endpoints, their respective logic found in
usba_control_irq()/usba_ep_irq() guarantees that TX FIFO is empty before
data is sent out, and that request_complete() gets called once the
transaction has been finished. At this point however, if any additional
requests are found on the endpoint queue, they will be processed by
submit_next_request(), which makes no checks against the above
conditions, trashing data on a busy FIFO and neglecting completion
handlers.
Fix the above issues by removing the calls to submit_next_request(),
and thus forcing the pending requests to be processed on the next pass
of the respective endpoint logic. While at it, remove a DBG message, as
that branch becomes part of regular flow.
This restores mass storage mode operation on Microchip ATSAMA5D27 SoC.
Signed-off-by: Artur Rojek <artur@conclusive.pl>
For some Amlogic SOC's, mechanism to obtain random number
has been changed. For example, S4 now uses status bit waiting algo.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231012075828.22685-2-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
In the MTD DFU backend, it is needed to mark the NAND block bad when the
erase failed with the -EIO error, as it is done in UBI and JFFS2 code.
This operation is not done in the MTD framework, but the bad block
tag (in BBM or in BBT) is required to avoid to write data on this block
in the next DFU_OP_WRITE loop in mtd_block_op(): the code skip the bad
blocks, tested by mtd_block_isbad().
Without this patch, when the NAND block become bad on DFU write operation
- low probability on new NAND - the DFU write operation will always failed
because the failing block is never marked bad.
This patch also adds a test to avoid to request an erase operation on a
block already marked bad; this test is not performed in MTD framework
in mtd_erase().
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The offset variable = 'off' used in the error trace when limit is reach
on erase operation is incorect as 'erase_op.addr' is used in the loop.
This patch corrects the copy paste issue between the erase loop and
the write loop.
This patch also adds the 'remaining' information to allow to debug of
limit issues.
Fixes: 6015af28ee ("dfu: add backend for MTD device")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This adds more supported spinand devices from the Linux kernel
implementation.
This does not include the latest kernel implementation as this would
require a substantial amount of extra work due to the missing
ECC engine abstraction layer in U-Boot.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> (commit message)
Link: https://lore.kernel.org/all/20230110115843.391630-3-frieder@fris.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
This brings us closer to the current Linux kernel implementation of
the spinand core and makes backporting features and fixes easier.
This does not include the latest kernel implementation as this would
require a substantial amount of extra work due to the missing
ECC engine abstraction layer in U-Boot.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> (add commit message)
Link: https://lore.kernel.org/all/20230110115843.391630-2-frieder@fris.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Currently there are 3 different variants of read_id implementation:
1. opcode only. Found in GD5FxGQ4xF.
2. opcode + 1 addr byte. Found in GD5GxGQ4xA/E
3. opcode + 1 dummy byte. Found in other currently supported chips.
Original implementation was for variant 1 and let detect function
of chips with variant 2 and 3 to ignore the first byte. This isn't
robust:
1. For chips of variant 2, if SPI master doesn't keep MOSI low
during read, chip will get a random id offset, and the entire id
buffer will shift by that offset, causing detect failure.
2. For chips of variant 1, if it happens to get a devid that equals
to manufacture id of variant 2 or 3 chips, it'll get incorrectly
detected.
This patch reworks detect procedure to address problems above. New
logic do detection for all variants separatedly, in 1-2-3 order.
Since all current detect methods do exactly the same id matching
procedure, unify them into core.c and remove detect method from
manufacture_ops.
This is a rework of Chuanhong Guo <gch981213@gmail.com> patch
submitted to linux kernel
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/all/20230110115843.391630-1-frieder@fris.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
AVS driver needs to be notified before or after clock change,
depending upon new rate is greater or less than current clock rate.
Fixes: 1e0aa873bc7cd ("clk: clk-ti-sci: Notify AVS driver upon setting clock rate")
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
AVS is enabled at R5 SPL stage, on few platforms like J721E
and J7200 clk-k3 is used instead if clk-sci driver.
Add support in clk-k3 driver as well to notify AVS driver
on setting clock rate so that voltage is changed accordingly.
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
We use this clocks in dwc3 driver.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231005085434.74755-7-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Setting G12A and A1 is similar, so we can use G12A phy
driver with little changes.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231005085434.74755-6-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
It is better to use defines instead of write raw
hex values in regmap.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231005085434.74755-4-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
This patch adds reset support for the Amlogic A1 family.
We add the structure meson_reset_drvdata, which in the future
will allow this driver to be used for other families by declaring
only the correct parameters reg_count and level_offset.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231005085434.74755-3-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
This patch adds basic clock driver for Amlogic A1 Family which supports
enabling/disabling some gates, getting frequencies and setting rate
with limited reparenting.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230925155209.130671-3-ivprusov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add rudimentary support for displaying a cursor on a vidconsole. This
helps the user to see where text is being entered.
The implementation so far is very simple: the cursor is just a vertical
bar of fixed width and cannot be erased. To erase the cursor, the text
must be redrawn over it.
This is good enough for expo but will need enhancement to be useful for
the command-line console. For example, it could save and restore the
area behind the cursor.
For now, enable this only for expo, to reduce code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this is called only when a newline is detected, since this
indicates the start of a line of text being entered.
Export this function so it can be used by expo, which may start a new
text line itself, without first writing out a newline.
Signed-off-by: Simon Glass <sjg@chromium.org>
Text entry operates within a context which includes quite a bit of
information. For example, with Truetype fonts, each character in the
text string has a position stored, so that it is possible to
backspace to that character. This information is built up as strings
are drawn on the display.
For the command line, there is just a single context. It is created
when command-line entry starts and it is destroyed (or at least not
needed anymore) when the user presses <enter> to enter the command.
By contrast, expo needs to be able to switch in and out of a text-entry
context, since it is also displaying other objects in the scene.
Add a way to save and restore the entry context for a vidconsole. This
is only needed for the truetype vidconsole, so add a method for that,
storing the information in an abuf struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there is a method for measuring text, but if the actual text
string is not known, it cannot be used.
For text editor we want to set the size of the entry box to cover the
expected text size. Add the concept of a 'norminal' size with a method
to calculate that for the vidconsole.
If the method is not implemented, fall back to using the font size,
which is sufficient for fixed-width fonts.
Signed-off-by: Simon Glass <sjg@chromium.org>
DM_DRIVER_GET will redeclare the fs_loader driver without the correct
alignment. This causes GCC to use the default section alignment of 32
bytes. This in turn creates a gap in the linker list due to the padding
required to achieve the correct alignment, corrupting all further entries.
Use DM_DRIVER_REF instead, which doesn't redeclare anything.
Fixes: 0998a20cfc ("misc: fs_loader: Add function to get the chosen loader")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
The ARMv8.5 architecture extension defines architectural RNDR/RNDRRS
system registers, that provide 64 bits worth of randomness on every
read. Since it's an extension, and implementing it is optional, there is
a field in the ID_AA64ISAR0_EL1 ID register to query the availability
of those registers.
Add a UCLASS_RNG driver that returns entropy via repeated reads from
those system registers, if the extension is implemented.
The driver always binds, but checks the availability in the probe()
routine.
This helps systems which suffer from low boot entropy, since U-Boot can
provide entropy via the generic UEFI entropy gathering protocol to the OS,
at an early stage.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With commit 793e623011 ("spi: mtk_spim: get spi clk rate only once") a
new system to calculate the SPI clocks has been added.
Unfortunately, the do_div macro overrides the global priv->pll_clk_rate
field. This will cause to have a reduced clock rate on each subsequent
SPI call.
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Before using the result of env_get("stdin") we must check if it is NULL.
Avoid #if. This resolves the -Wunused-but-set-variable issue and we don't
need a dummy assignment in the else branch. Anyway this warning is
disabled in the Makefile.
For sake of readability use an early return after the configuration check.
Checking CONFIG_SPL_BUILD is incorrect as env_get() is only defined if
CONFIG_$(SPL_TPL)ENV_SUPPORT=y.
Fixes: 985ca3945f ("spl: input: Allow input in SPL and TPL")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
blk_{read,write}_devnum() are no longer used by anywhere in the
source tree. Drop them.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
get_desc() can be useful outside blk-uclass.c. Let's change it to
an API and make it externally visible.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present if a device to map has a block size other than 512,
the blkmap map process just fails. There is no reason why we
can't just use the block size of the mapped device.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since we are emulating a block device, its size should be multiple
of the configured block size.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Allow optionally set the logical block size of the host device to
bind in the "host bind" command. If not given, defaults to 512.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
As the xlnx,phy-type device tree property is deprecated and phy-mode
is being used, so removing the code references of xlnx,phy-type.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231010030436.11854-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reset the FLSHxCR1 registers to default value. ROM may set the register
value and it affects the SPI NAND normal functions.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for declaring in device tree the reserved memory ranges
required for MC. Since the MC firmware acts as any DMA master present
in the SoC, the reserved memory ranges need also be identity mapped
in the SMMU, so create the required 'iommu-addresses' property in
the reserved memory nodes.
For now this support is used only on LX2160A SoCs.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The size of the name of a udevice is not limited.
When setting the fixed sized name field of a stdio device we must ensure
that the target string is NUL terminated to avoid buffer overflows.
Fixes: 57d92753d4 ("dm: Add a uclass for serial devices")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This partially reverts commit ff33227819.
Versal NET clock node should use "xlnx,versal-net-clk", "xlnx,versal-clk"
compatible string that's why it is not necessary to define Versal NET
specific compatible string if there is no any other change needed. It can
be get back if there is a need to differentiate clock support between
Versal and Versal NET.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c09276022db5f1b150679cc7a9f9583363ace2fb.1695808971.git.michal.simek@amd.com
Read the tristate config for all the pins and display it.
ZynqMP> pinmux status MIO1
MIO1: slew:fast bias:enabled pull:up input:cmos drive:12mA
volt:1.8 tri_state:enabled
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230914100620.26346-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
MDC clock change needs to be done when the driver probe function
is called as mdio is enabled at probe and not when the ethernet starts.
Setup the MDC clock at the probe itself.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230922045010.22852-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- Add Board: rk3568 Bananapi R2Pro;
- Update pcie bifurcation support;
- dwc_eth_qos controller support for rk3568 and rk3588;
- Compressed binary support for U-Boot on rockchip platform;
- dts and config updates for different board and soc;
[ trini: Fix conflict on include/spl.h ]
Signed-off-by: Tom Rini <trini@konsulko.com>
The commit 30975fb73d ("rockchip: Add option to prevent booting on
power plug-in") introduce an option to prevent booting a device when the
device was powered on due to power plug-in instead of pressing a power
button.
This feature works by checking the power-on source during PMIC probe
and powers off the device if power-on source was power plug-in.
This check currently runs very late at PMIC probe in U-Boot proper.
Fix so that the power-on source check can work at probe time in SPL.
Also enable probe after bind and remove the PMIC banner in SPL.
With this we can use ROCKCHIP_RK8XX_DISABLE_BOOT_ON_POWERON and
SPL_PMIC_RK8XX to power off the device very quickly after TPL instead
of after TF-A and U-Boot proper has been loaded and run.
DDR V1.18 f366f69a7d typ 23/07/17-15:48:58
ln
LP4/4x derate en, other dram:1x trefi
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=8192MB
change to: 324MHz
clk skew:0x64
change to: 528MHz
clk skew:0x58
change to: 780MHz
clk skew:0x58
change to: 1056MHz(final freq)
clk skew:0x40
out
Power Off due to plug-in event
Fixes: 30975fb73d ("rockchip: Add option to prevent booting on power plug-in")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Select SYSRESET_CMD_POWEROFF to use the sysreset implementation of the
poweroff command when PMIC_RK8XX is enabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add rk_gmac_ops and other special handling that is needed for GMAC to
work on RK3588.
rk_gmac_ops was ported from linux commits:
2f2b60a0ec28 ("net: ethernet: stmmac: dwmac-rk: Add gmac support for rk3588")
88619e77b33d ("net: stmmac: rk3588: Allow multiple gmac controller")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a new glue driver for Rockchip SoCs, i.e RK3568, with a GMAC based
on Synopsys DWC Ethernet QoS IP.
rk_gmac_ops was ported from linux commit:
3bb3d6b1c195 ("net: stmmac: Add RK3566/RK3568 SoC support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Remove spam of RX packet not available debug messages when waiting to
receive a packet.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Return error code when phy_connect fails or no link can be established.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
rx_pkt is allocated and not used for anything, remove it.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Port the Rockchip IO-domain driver for RK3568 from linux.
The driver auto probe after bind to configure IO-domain based on the
regulator voltage. Compared to the linux driver this driver is not
notified about regulator voltage changes and only configure IO-domain
based on the initial voltage autoset by the regulator.
It is not recommended to enable MMC_IO_VOLTAGE or the mmc signal voltage
and IO-domain may end up out of sync.
Based on the linux commit 28b05a64e47c ("soc: rockchip: io-domain: add
rk3568 support").
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The voltage value for switchout converters is always reported as 0 uV.
When the switch is enabled, it's voltage is same as input supply.
Fix this by implementing get_value for switchout converters.
Fixes: ee30068fa5 ("power: pmic: rk809: support rk809 pmic")
Signed-off-by: shengfei Xu <xsf@rock-chips.com>
[jonas@kwiboo.se: fix checkpatch error, update commit message]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Information from the first range group is always used to calculate the
voltage returned for buck converters. This may result in wrong voltage
reported back to the regulator_get_value caller.
Traverse all the possible BUCK ranges to fix this issue.
Fixes: addd062bea ("power: pmic: rk816: support rk816 pmic")
Fixes: b62280745e ("power: pmic: rk805: support rk805 pmic")
Fixes: b4a35574b3 ("power: pmic: rk817: support rk817 pmic")
Fixes: ee30068fa5 ("power: pmic: rk809: support rk809 pmic")
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
[jonas@kwiboo.se: fix checkpatch error, simplify buck get_value, update commit message]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter"), keeping regulator enablement in balance become more important.
Calling regulator_autoset multiple times on a fixed regulator increase
the enable count for each call, resulting in an unbalanced enable count.
Introduce a AUTOSET_DONE flag and use it to mark that autoset has run
for the regulator. Return -EALREADY on any subsequent call to autoset.
This fixes so that the enable count is only ever increased by one per
regulator for autoset.
Fixes: 4fcba5d556 ("regulator: implement basic reference counter")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Route signal from comb PHY instead of PCIe3 PHY to PCIe1l0 and PCIe1l1.
Fixes use of pcie2x1l0 on ROCK 5B.
Code imported from mainline linux driver.
Fixes: c5b4a012bc ("phy: rockchip: naneng-combphy: Support rk3588")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the RK3588 variant to the driver.
Code imported almost 1:1 from mainline linux driver.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Configure aggregation or bifurcation mode on RK3568 based on the value
of data-lanes property.
Code imported almost 1:1 from mainline linux driver.
Fixes: 6ec62b6ca6 ("phy: rockchip: Add Rockchip Synopsys PCIe 3.0 PHY")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a phy_init ops in preparation for upcoming support of a RK3588
variant in the driver.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change to use clk_bulk API and syscon_regmap_lookup_by_phandle to
simplify in preparation for upcoming support of a RK3588 variant.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Set number of lanes and link width speed control register based on the
num-lanes property.
Code imported almost 1:1 from dw_pcie_setup in mainline linux.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The PCI helpers read only the base address for a PCI region. In some cases
the size is needed as well, e.g. to pass along to a driver which needs to
know the size of its register area.
Update the functions to allow the size to be returned. For serial, record
the information and provided it with the serial_info() call.
A limitation still exists in that the size is not available when OF_LIVE
is enabled, so take account of that in the tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
This currently relies on sandbox attempting to read a state file. At
present it always does, even when there is no state file, in which case it
fails, but still inits the EC.
That is a bug, so update this driver to set the current image always, even
if no state is read.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for writing a single 64-bit value into a property.
Repurpose the existing tests to handle this case too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add functions to write a boolean property. This involves deleting it if
the value is false.
Add a new ofnode_has_property() as well. Add a comment about the behaviour
of of_read_property() when the property value is empty.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a way to flatten a devicetree into binary form. For livetree this
involves generating the devicetree using fdt_property() and other calls.
For flattree it simply involves providing the buffer containing the tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function to copy a node to another place under a new name. This is
useful at least for testing, since copying a test node with existing
properties is easier than writing the code to generate it all afresh.
Signed-off-by: Simon Glass <sjg@chromium.org>
These symbols do not (yet) exist, so drop the usage of them in the
serial Kconfig file. It has no effect.
Signed-off-by: Simon Glass <sjg@chromium.org>
We like to put the SPL first so it is clear that it relates to SPL. Rename
various malloc-related options which have crept in, to stick to this
convention.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
+ ae350: modify memory layout and target name
+ ae350: use generic RISC-V timer driver in S-mode
+ Support bootstage report for RISC-V
+ Support C extension exception command for RISC-V
+ Add Starfive timer support
When setting up boot media to load the TIFS binary in legacy boot flow
(followed by J721E), get_timer() is called which calls dm_timer_init()
which then gets the tick-timer: mcu_timer0. mcu_timer0 uses k3_clks
(clock controller) and k3_pds (power controller) from the dmsc node that
forces probe of the ti_sci driver of TIFS that hasn't been loaded yet!
Running ti_sci_cmd_get_revision from the probe leads to panic since no
TIFS and board config binaries have been loaded yet. Resolve this by
moving ti_sci_cmd_get_revision to ti_sci_get_handle_from_sysfw as a
common point of invocation for both legacy and combined boot flows.
Before doing this, it is important to go through whether any sync points
exist where revision is needed before ti_sci_get_handle_from_sysfw is
invoked. Going through the code along with boot tests on both flows
ensures that there are none.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
_ alignment with kernel DT v6.5 for stm32f429 and stm32f746
_ rework way of displaying ST logo for stm32f746-disco and stm32f769-disco
STM32 MPU:
_ alignment with kernel DT v6.6-rc1
_ add RNG support for stm32mp13
_ add USB, USB boot and stm32prog command support for stm32mp13
_ add support of USART1 clock for stm32mp1
_ only print RAM and board code with SPL_DISPLAY_PRINT flag for
stm32mp1
_ rename update_sf to dh_update_sd_to_sf and add dh_update_sd_to_emmc
for stm32mp15xx DHCOR
-----BEGIN PGP SIGNATURE-----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=1mUx
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20231004' of https://source.denx.de/u-boot/custodians/u-boot-stm
STM32 MCU:
_ alignment with kernel DT v6.5 for stm32f429 and stm32f746
_ rework way of displaying ST logo for stm32f746-disco and stm32f769-disco
STM32 MPU:
_ alignment with kernel DT v6.6-rc1
_ add RNG support for stm32mp13
_ add USB, USB boot and stm32prog command support for stm32mp13
_ add support of USART1 clock for stm32mp1
_ only print RAM and board code with SPL_DISPLAY_PRINT flag for
stm32mp1
_ rename update_sf to dh_update_sd_to_sf and add dh_update_sd_to_emmc
for stm32mp15xx DHCOR
[ Fix merge conflict at board/st/common/stm32mp_dfu.c ]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add USART1 clock parents and mux configuration. This allows
support for configuring the USART1 as the serial console in
SPL and U-Boot via device tree. Without this patch the SPL
with usart1 serial console enabled crashes because it can
not find the clock specified in the device tree for usart1.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Ensure that the RAM configuration line is only printed when
CONFIG_SPL_DISPLAY_PRINT is set.
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
STM32 RNG configuration should best fit the requirements of the
platform. Therefore, put a platform-specific RNG configuration
field in the platform data. Default RNG configuration for STM32MP13
is the NIST certified configuration [1].
While there, fix and the RNG init sequence to support all RNG
versions.
[1] https://csrc.nist.gov/projects/cryptographic-module-validation-program/entropy-validations/certificate/53
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Seed errors can occur when using the hardware RNG. Implement the
sequences to handle them. This avoids irrecoverable RNG state.
Try to conceal seed errors when possible. If, despite the error
concealing tries, a seed error is still present, then return an error.
A clock error does not compromise the hardware block and data can
still be read from RNG_DR. Just warn that the RNG clock is too slow
and clear RNG_SR.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In order to ensure a good RNG quality and compatibility with
certified RNG configuration, add RNG clock frequency restraint.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
RNG clock error detection is now enabled if the "clock-error-detect"
property is set in the device tree.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Rename the RNG driver as it is usable by other STM32 platforms
than the STM32MP1x ones. Rename CONFIG_RNG_STM32MP1 to
CONFIG_RNG_STM32
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The Andes PLMT driver directly accesses the mtime MMIO region,
indicating its intended use in the M-mode boot stage. However,
since U-Boot proper (S-mode) also uses the PLMT driver, we need
to specifically mark the region as readable through PMPCFGx (or
S/U-mode read-only shared data region for Smepmp) in OpenSBI.
Granting permission for this case doesn't make sense. Instead,
we should use the generic RISC-V timer driver to read the mtime
through the TIME CSR. Therefore, we add the SPL_ANDES_PLMT_TIMER
config, which ensures that the PLMT driver is linked exclusively
against M-mode U-Boot or U-Boot SPL binaries.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Add timer driver in Starfive SoC. It is an timer that outside
of CPU core and inside Starfive SoC.
Signed-off-by: Kuan Lim Lee <kuanlim.lee@starfivetech.com>
Reviewed-by: Wei Liang Lim <weiliang.lim@starfivetech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
timer_get_boot_us function is required to record the boot stages as
us-based timestamp.
To get a micro-second time from a timer tick, this converts the
formula like below to avoid zero result of (tick / rate) part.
From: time(us) = (tick / rate) * 1000000
To : time(us) = (tick * 1000) / (rate / 1000)
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
timer_get_boot_us function is required to record the boot stages as
us-based timestamp.
To get a micro-second time from a timer tick, this converts the
formula like below to avoid zero result of (tick / rate) part.
From: time(us) = (tick / rate) * 1000000
To : time(us) = (tick * 1000) / (rate / 1000)
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Synchronize R8A774E1 RZ/G2H clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774C0 RZ/G2E clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774B1 RZ/G2N clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774A1 RZ/G2M clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779G0 V4H clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
The PLL2_VAR is not implemented yet and PLL2 is still configured
as regular PLL2 only.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77960 M3-W and R8A77961 M3-W+ clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7791 M2-W and R8A7793 M2-N clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
