The Goldfish RTC is a virtual device which may be supplied by QEMU.
It is enabled by default on QEMU's RISC-V virt machine.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
In some designs the MAX313xx RTC may need calibration to cope with
oscillator inaccuracies. Provide read8/write8 ops so that the registers
can be accessed. Because the driver covers a range of MAX313xx variants
no attempt is made to ensure the register is valid.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Adding support for Analog Devices MAX313XX series RTCs.
This is ported from the Linux driver and adapted for use in u-boot.
Notable differences are
- handling of tm_year and tm_mon differ
- clock source support is omitted
- hwmon support for the MAX31328 and MAX31343 is omitted
- rtc_ops->reset is added
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These operations are required by dm_rtc_read and
dm_bootcount_get helpers.
Signed-off-by: Thomas Perrot <thomas.perrot@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present we enable the sandbox RTC driver for all builds. Add a separate
Kconfig option to control this, so that it can be disabled in TPL, where
it is not needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
These drivers are not used and have not been converted to driver model.
Drop them and references to the non-existent CONFIG options they use.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds support for reading the battery-backed memory present on these
RTCs. This modifies the read/write methods to access the RAM instead of
raw register offsets. No one was using these in-tree, so we should be
fine changing them.
We use the "standard" address space window to access the RAM. The
extension RAM address register has some reserved bits, but we write the
whole thing for simplicity (as these bits default to 0).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Support Holtek HT1380/HT1381 Serial Timekeeper Chip. It provides seconds
, minutes, hours, day of the week, date, month and year information.
Datasheet:
https://www.holtek.com.tw/documents/10179/11842/ht1380_1v130.pdf
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_RTC_DS1337
CONFIG_RTC_DS1337_NOOSC
CONFIG_RTC_DS1338
CONFIG_RTC_DS1374
CONFIG_RTC_DS3231
CONFIG_RTC_MC13XXX
CONFIG_RTC_MXS
CONFIG_RTC_PT7C4338
Signed-off-by: Tom Rini <trini@konsulko.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These RTC drivers are currently unused and reference other unused CONFIG
variables, so remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_INTERLAKEN
CONFIG_SYS_ISA_IO
CONFIG_SYS_ISA_IO_BASE_ADDRESS
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This uses the nvmem API to load a mac address from an RTC.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
tm_mon has a range from 0..11, but the RTC expects 1..12. So we adapt
the month accordingly. This was determined when comparing the driver
with the corresponding linux kernel driver.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Schocher <hs@denx.de>
This converts the following to Kconfig:
CONFIG_MCFRTC
CONFIG_SYS_MCFRTC_BASE
While at it, remove '#undef RTC_DEBUG' from these config files.
Signed-off-by: Tom Rini <trini@konsulko.com>
Replace null pointer by pointer to device registers when calling
armada38x_rtc_write.
Signed-off-by: Francois Berder <fberder@outlook.fr>
Reviewed-by: Stefan Roese <sr@denx.de>
Compatible string microchip,mcp7940x is used by Turris Mox DTS file in
Linux kernel and U-Boot ds1307.c driver works fine with it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that all in-tree boards have been converted to the compatible
strings from Linux, delete the support for the ad-hoc "pcf2127-rtc" one.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Allow this driver to be used by boards which inherit their device trees
from Linux. Compatibility is temporarily retained with the old
compatible string which is U-Boot specific, and will be removed after a
few changes.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The driver supports the ds1339 as well, which was probably intended by
the author but prevented by a typo. Fix the typo.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
The DS1307 driver was originally based on the DS1337 driver. However,
the functionality of the clock set/get functions has diverged. In the
original DS1337 driver, the set/get functions did the following:
1) Setting the clock ensured the oscillator was enabled.
2) Getting the clock checked and reset the oscillator-stop flag.
The DS1307 does not have an oscillator-stop flag, but the driver tried
(incorrectly) to emulate this by ensuring the oscillator was running. It
really makes no sense to start a stopped clock without setting it.
This patch makes the DS1307 driver behave like the original DS1337
driver again. For the DS1307 itself, this is just a removal of code,
since there is no oscillator-fail bit to check or reset, and the clock
is started when it is set. Since the DS1307 driver can now also be used
for the DS1337 and DS1340 which do have this bit, add code to handle the
oscillator-stop bit in the same was the original DS1337 driver did --
i.e. report that the oscillator had stopped and clear the flag.
This means that setting the date using the date command (which does both
a get and a set) will now clear the oscillator-stop flag in addition to
setting and starting the clock.
The old-style (non-DM) code has not been updated and will be removed in
a future patch. Note that this older code does not support the DS1337,
as there is a separate driver for this. Also note that the original (DM)
code used the wrong control-register address for the DS1337.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
The RX8803 and RX8900 register layouts are compatible with the one of
the RV8803. So add these to the compatibles.
The same compatible strings are used and approved in linux kernel.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Writing of individual registers was not functioning
correctly as a 0 'offset' byte under DM-managed
I2C was being appended in front of register we
wanted to access.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The RX8025/RX8035 does not like having it's time registers
set byte-by-byte in separate I2C transactions.
From the note at the top of the file, it appears
target-dependent workarounds have been used in the
past for this.
Resolve this by setting the time registers in a single
I2C transaction.
As part of this, also ensure the '24/12' flag in the RTC
is reset before writing the date (instead of after), otherwise
the RX8035 will clear the seconds and minutes registers.
Tested on Traverse Ten64 (NXP LS1088A) with RX8035.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The RX8035 is a newer model from EPSON which is
very similar in operation to the RX8025.
The changes mirror similar ones that will be
in Linux 5.15:
https://lore.kernel.org/all/20210709044518.28769-2-matt@traverse.com.au/
The UBOOT_DRIVER ID has also been corrected, previously
it declared itself as rx8010sj_rtc which is a different driver.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
A search of the tree showed there is only one user
of this driver (soon to be two) - board/socrates
The second user will be the Traverse Ten64 board.
Both these boards have DM_RTC.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Now that we have a 'positive' Kconfig option, use this instead of the
negative one, which is harder to understand.
Signed-off-by: Simon Glass <sjg@chromium.org>
Header file version.h does not use anything from timestamp.h. Including of
timestamp.h has side effect which cause recompiling object file at every
make run because timestamp.h changes at every run.
So remove timestamp.h from version.h and include timestamp.h in files
which needs it.
This change reduce recompilation time of final U-Boot binary when U-Boot
source files were not changed as less source files needs to be recompiled.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add in lib/acpi/acpi_table.c and test/dm/acpi.c, rework a few others]
Signed-off-by: Tom Rini <trini@konsulko.com>
The ds1307 driver also supports the DS1339 and DS1340.
However, in ds1307_rtc_reset the register writes assume that the chip
is a DS1307. This is evident in the writing of bits SQWE, RS1, RS0 to
the control register. While this applies correctly to the DS1307, on a
DS1340 the control register doesn't contain those bits (instead, the
register is used for clock calibration). By writing these bits the
clock calibration will be changed and the chip can become
non-functional after a reset call.
Signed-off-by: Callum Sinclair <callum.sinclair@alliedtelesis.co.nz>
The whole driver logic is taken from Linux kernel but only set/get/reset
functions are implemented. When device is power off RTC is power out of
battery.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
RTCs are using aliases for sequences. That's why enable
DM_UC_FLAG_SEQ_ALIAS for exact RTC indentification.
The same flag is used by a lot of other uclasses like mmc, pci, serial,
spi, timer, tpm, etc.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is a pain to have to specify the value 16 in each call. Add a new
hextoul() function and update the code to use it.
Add a proper comment to simple_strtoul() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix wrong register use when set/reset ST bit.
ST bit is in register M41T62_REG_SEC not in M41T62_REG_ALARM_HOUR.
I have not actually tested this. But this seemed buggy from inspection.
Fixes: 9bbe210512 ("rtc: m41t62: add oscillator fail bit reset support")
Signed-off-by: Max Yang <max.yang@deltaww.com>
Function rtc_to_tm() is needed for FAT file system support even if we don't
have a real time clock. So move it from drivers/ to lib/.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On reset, the RTC loads the 2000-01-01 date with a wrong day of the
week (Sunday instead of Saturday).
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-9-dariobin@libero.it
Update the driver to support the device tree and the driver model.
The read / write helpers in rtc_ops allow access to scratch registers
only. The offset parameter is added to the address of the scratch0
register.
Support for non-DM has been removed as there were no users.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-8-dariobin@libero.it
The RTC module contains a kicker mechanism to prevent any spurious
writes from changing the register values. To set the time, you must
first unlock the TC registers, update them and then lock.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-6-dariobin@libero.it
To write correct data to the TC registers, the STATUS register must be
read until the BUSY bit is equal to zero. Once the BUSY flag is zero,
there is a 15 μs access period in which the TC registers can be
programmed.
The rtc_wait_not_busy() has been inspired by the Kernel.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-5-dariobin@libero.it
Use 32-bit access only where it is needed. Most of the RTC registers
contain useful information in the 8 least significant bits, the others
are reserved.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-4-dariobin@libero.it
The Davinci's onchip RTC is also present on TI OMAP1, AM33XX, AM43XX and
DRA7XX SOCs. So, let's enable compilation for these architectures too.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-2-dariobin@libero.it
Add support for rtc3028 rtc from microcrystal.
based on linux dirver:
commit a38fd8748464: ("Linux 5.12-rc2")
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
