Add Support for UFS Host Controller Interface (UFSHCI) for communicating
with Universal Flash Storage (UFS) devices. The steps to initialize the
host controller interface are the following:
- Initiate the Host Controller Initialization process by writing to the
Host controller enable register.
- Configure the Host Controller base address registers by allocating a
host memory space and related data structures.
- Unipro link startup procedure
- Check for connected device
- Configure UFS host controller to process requests
Also register this host controller as a SCSI host controller.
Taken from Linux Kernel v5.2 (drivers/scsi/ufs/ufshcd.c) and ported to
U-boot.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Some SCSI devices like UFS use DMA for executing scsi commands and hence
need to know the direction of transfer of the dma. Add a dma_dir element
to the command structure to facilitate this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The UFS SCSI device LUNs are observed to return failure the first time a
unit ready inquiry is sent and pass on the second try. Send this
inquiry 3 times to make sure device is ready.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add max_bytes_per_req to scsi_platdata to enable the host driver to limit
the number of bytes that can be read/written per request.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
With no non-DM driver using scsi_read()/_write() APIs, remove
the legacy implementations.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
[trini: Reorder slightly and mark scsi_read/write behind BLK test to
avoid warnings]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Fix ramdisk_addr_r for stm32f746-disco
- Fix USB product id for stm32mp1
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl2wHd8ACgkQ4rK92eCq
k3UEBQgAkVeXgew8P7Z/ATK6jGArMWF+OGbh+Eveb1/vD1opcizyvVm4gxg/RRQA
+yDuXhd0fXoaug4okDXplJXg7j6YRVr2PUPVoGYMcaLOX4TUcXXf+6rYycC4mzVS
5vF5Fb9k+Wu/5rI+7y0IJH2zoAvLtEJ1+8vDwH3oCIBgsTYn54FwOXU76ni9NzA/
n5Gs8Xn09TJb5BtZ/CNdBYgJ+4bDystzhVTbmaAUYSX075wMl4+Dax9EZLwc5941
3Ix5yzsDRYObrLhvZgSr3EaVcoxa6y7E3488D9o5voPbDsO5XMXf72MVFjMGJClQ
03q2RP1rNnDYzfGvPTztWPpSvgxC0A==
=UmF/
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-2019-10-23' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Disable CONFIG_NET flag for MCU STM32
- Fix ramdisk_addr_r for stm32f746-disco
- Fix USB product id for stm32mp1
Make sure that the clock self-assignment works by having a clock of
clk-sbox be configured automatically when clk-sbox is probed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This fixes the case where assigned-clocks is used to define a clock
defaults inside this same clock's node. This is used sometimes to setup a
default parents and/or rate for a clock.
example:
muxed_clock: muxed_clock {
clocks = <&clk_provider 0>, <&clk_provider 1>;
#clock-cells = <0>;
assigned-clocks = <&muxed_clock>;
assigned-clock-parents = <&clk_provider 1>;
};
It doesn't work in u-boot because the assigned-clocks are setup *before*
the clock is probed. (clk_set_parent() will likely crash or fail if called
before the device probe function)
Making it work by handling "assigned-clocks" in 2 steps: first before the
clk device is probed, and then after the clk device is probed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a few more clocks the clk_sandbox clock provider and get them using
the managed API.
Make sure they are released when the device is removed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add devm_clk_get(), devm_clk_get_optional() to get clocks from the
device-tree. The clocks is automatically released and the data structure
freed when the device is unbound.
Also add devm_clk_put() to release the clock and free the data structure
manually.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This change adds support for I2C clock modeled in CCF. This code intention
is to only enable those clocks in the I2C driver with default settings.
For that reason the "busy" versions of clocks reuse the generic approach
and would need to be updated when one wants to adjust the I2C clock
frequency in U-Boot.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
According to the documentation in clk.h, clk_set_parent() return the new
rate of the clock or a negative error code.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Select the correct USB product id used by the download gadget
for ST stm32mp1 boards.
The board stm32mp1 select the correct product id, as defined in
http://www.linux-usb.org/usb.ids for the STMicroelectronics
vendor id = 0x0483 (CONFIG_USB_GADGET_VENDOR_NUM):
- dfu = 0xdf11 : STM Device in DFU mode
it is the value used by ROM code and reused for stm32prog
command
- fasboot = 0x0afb : Android Fastboot device
- others = 0x5720 (CONFIG_USB_GADGET_PRODUCT_NUM)
Mass Storage Device
it is used for UMS command / usb_dnl_ums
This patch avoid conflict when the same USB VID/PID is used for
ums, fastboot or dfu command (two different protocols associated
to the same PID).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Correct the name of the define used CONFIG_IS_ENABLED which is
not aligned with Kconfig name: CONFIG_$(SPL_)PINCONF_RECURSIVE.
The recursive calls is conditional only for UCLASS_PINCONFIG
"pinconfig" driver.
It is always needed to call pinctrl_post_bind for UCLASS_PINCTRL
"pinctrl", the test CONFIG_IS_ENABLED(PINCONF_RECURSIVE) need to
be removed for this driver.
This correct a regression introduced because the same patch is
applied twice times in u-boot-dm branch:
- commit e878b53a79 ("dm: pinctrl: introduce PINCONF_RECURSIVE
option")
- commit c20851b3d8 ("dm: pinctrl: introduce PINCONF_RECURSIVE
option")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
To allow OCRAM to be used as wakeup source in
deep sleep, do not power it down.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The patch adds an errata ID A-008646 for workaround
to provide more information by errata ID.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
LX2160A/LX2120A/LX2080A SVR value should be
0x873600/0x873620/0x873602
Previous values were valid only if CAN fuse is blown.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
ls1028a has 4 personalities: ls1028a, ls1027a, ls1017a and ls1018a.
Both ls1027a and ls1017a personalities are lower functionality version
which doesn't support the multimedia subsystems, like LCD, GPU.
To disable multimedia feature on non-multimedia version,
set the status property to disabled in dts nodes.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This configuration enables picking the environment from flash before
DDR init.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Program register bit of SCFG_SNPCNFGCR_USBxRDSNP and
SCFG_SNPCNFGCR_USBxWRSNP(x = 1, 2, 3) to drive USBx read/write
snoop signal on LS1043A and LS1046A.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add LS1027A, LS1018A and LS1017A personalities support to
LS1028A SoC family.
LS1028A is the prime personality of LS1028A SoC family.
LS1027A is a lower funtionality version of QorIQ LS1028A
which does not support the multimedia subsystems, such as LCD
controller, GPU, and eDP PHY.
The QorIQ LS1018A and LS1017A SoCs are single 64-bit Arm A72
core, low power versions of the QorIQ LS1028A and LS1027A
SoCs respectively.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Loading U-Boot on i.MX8QXP MEK board is broken since recent changes
in spl_mmc:
U-Boot SPL 2019.10-00162-gff5bd397e4 (Oct 18 2019 - 15:50:45 +0200)
Normal Boot
WDT: Not found!
Trying to boot from MMC2_2
Load image from MMC/SD 0x46400
spl: mmc partition switch failed
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
The newly added CONFIG_SYS_MMCSD_RAW_MODE_EMMC_BOOT_PARTITION option
is selected automatically and overrides the EXT_CSC_PART_CONFIG
configurations with default value, always selecting the eMMC boot
partition 1. Boards which place U-Boot image in other partitions
became not bootable.
Fix this by making the eMMC HW boot partition selection optional.
Fixes: 17241ea054 (spl: mmc: Add option to set eMMC HW boot partition)
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Install the simple file protocol only if there is a file system on the
partition.
Enable CONFIG_CMD_NVEDIT_EFI on QEMU.
-----BEGIN PGP SIGNATURE-----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=X+Tw
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc1-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc1 (2)
Install the simple file protocol only if there is a file system on the
partition.
Enable CONFIG_CMD_NVEDIT_EFI on QEMU.
- add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board
- add support for Amlogic A311D based Khadas VIM3
- add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
-----BEGIN PGP SIGNATURE-----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=g/kq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20191018' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- document alternative libretech-cc installation methods, including upstream TF-A and opensource tools
- add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board
- add support for Amlogic A311D based Khadas VIM3
- add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
Add separate config file to handle the different eMMC size on
the sei610 board.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move android generic config and boot sequence in meson64_android header
and fix size of userdata to use all eMMC on SEI510.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for the customer board SEI610 manufactured by SEI Robotics
with the following specifications:
- Amlogic S905X3 ARM Cortex-A55 quad-core SoC
- 2GB DDR4 SDRAM
- 10/100 Ethernet (Internal PHY)
- 1 x USB 3.0 Host
- 1 x USB Type-C DRD
- 1 x FTDI USB Serial Debug Interface
- eMMC
- SDcard
- Infrared receiver
- SDIO WiFi Module
Like it's SEI510 counterpart, the boot flow is designed to boot
Android AOSP built for the Yukawa Android device.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rename meson-g12a-u-boot.dtsi into meson-g12-common-u-boot.dtsi to
match the new DT architecture and add meson-sm1-sei610-u-boot.dtsi
to handle the U-Boot specific DT for graphics.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The GX VPU Power Domain driver has been replaced by the Everything-Else
Power Domain driver for G12A and SM1.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Based on the 54ecb8f7028c ("Linux 5.4-rc1") Everything-Else power domain
driver for Amlogic SoCs.
This driver handles the VPU Power domain and other domains from the
Everything-Else part of the SM1 and G12A SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The SM1 clock controller is almost identical to the G12A and
so far the differences don't matter.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
