xilinx_uartlite has been ported to DM, this patch makes the
xilinx-ppc405-generic and the xilinx-ppc440-generic boards use the new
DM driver.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Define auto negotiation timeout as 20secs
the default 4secs might not be sufficient
always and hence defined for worst case.
It is observed that autoneg takes moretime
if connected to outside network and hence
increase it to 20secs.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Dont use shortcut command for setenv as
it wont work now due introduction of new
command setexpr.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modify DFU commands to use latest kernel offsets and sizes
as per modified partitions in the linux device tree.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When U-Boot runs from EL3 system timer is setup based on this macro.
Software default freq for silicon is 100MHz but enable opton to rewrite
it. Emulation platform is using 4MHz.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When only sdhci1 IP is enabled and SD_MODE1 bootmode is selected
U-Boot using sdboot1 variable which refers to mmc dev 1.
But this device doesn't exist because only one controller is available.
This patch fix logic around sdboot mode with using sdbootdev internal
variable.
Reported-by: Chris Kohn <ckohn@xilinx.com>
Acked-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link to zynqmp common file is incorrect. Fix it by removing the whole
link because it is visible from the file where to look at it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define minimum sdhci frequency for ep, as not defining
it causes the divisor to be 2048 as per sd version but
keeping clock very low on ep causes command failures.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add bitstream type BIT_NONE to the bitstream type
enum. This might be useful while loading bitstreams
in respective drivers.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
board_init() is in final elf file but it is not called at all.
Use board_init_late() instead and call gpio_init() from it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add PHYLIB and MII dependencies and enable it by default for Microblaze.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To solve enabling ETH_DM where ksz90x1_reg_field is defined only when
additional Micrel type is defined.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- Move config option out of board file.
- Remove uartlite address from config file
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
-Remove UART address (It is now part of the dts).
-Include dummy ns16550 clock
-Fix address to last test
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Now that there is only one header file for all ppc405 files, merge
header files.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Now that there is only one header file for all ppc440 files, merge
header files.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
The old mail address will stop working soon.
Update it all the files
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
It is just a specialized version of xilinx-ppc440
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
It is just a specialized version of the xilinx-ppc405
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
ml507 is just a specialized version of the xilinx-ppc440-generic
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for the Armada XP (MV78260) based theadorable
board. Its equipped with onboard DDR3, UART, ethernet, I2C, SPI NOR,
LCD and SATA (SSD) interfaces / devices.
Two defconfigs are added:
theadorable_defconfig:
The production U-Boot version with a stripped down drivers and feature
list. This removes networking, USB and PCI support.
theadorable_debug_defconfig:
The debugging / testing U-Boot version with full support for all drivers.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
Instead of one function for each DLDO regulator, make 1 function that
takes an extra "index". Since the control bits for the DLDO regulators
are contiguous, this makes the function very simple. This removes a lot
of duplicate code.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some of the register definitions are duplicated. Drop them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Enabling CONFIG_DISPLAY breaks building for some architectures
(microblaze-generic), so we disable CONFIG_DISPLAY in Kconfig
by default and enable this option in defconfigs. CONFIG_DISPLAY
depends on CONFIG_I2C_EDID, so add and enable it in defconfigs, too.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory. These values
define the voltage requirements for the chip. u-boot reads
FUSESR and translates the values into the appropriate
commands to set the voltage output value of an external
voltage regulator.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Freescale's management complex (MC) uses System DDR for internal usage.
Increase used System DDR size from 256MB to 512 MB.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some images to be validated are relocated to a dynamic
address at run time. So, these addresses cannot be known
befor hand while signing the images and creating the header
offline.
So, support is required to pass the image address to the
validate function as an argument.
If an address is provided to the function, the address
field in Header is not read and is treated as a reserved
field.
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The prototype and defination of function fsl_secboot_validate
has been changed to support calling this function from another
function within u-boot.
Only two aruments needed:
1) header address - Mandatory
2) SHA256 string - optional
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Erratum A-009663 workaround requires to set DDR_INTERVAL[BSTOPRE] to 0
before setting DDR_SDRAM_CFG[MEM_EN] and set DDR_INTERVAL[BSTOPRE]
to the desired value after DDR initialization has completed.
When DDR controller is configured to operate in auto-precharge
mode(DDR_INTERVAL[BSTOPRE]=0), this workaround is not needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch also exposes the complete DDR region(s) to Linux.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Since we are manipulating GPIO 189 to determine the board type, we
need to enable the GPIO Bank 6.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Do not undefine CONFIG_BOOTDELAY, so board can boot without user
intervention.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
BUILD_BUG_* macros have been defined in several headers. It would
be nice to collect them in include/linux/bug.h like Linux.
This commit is cherry-picking useful macros from include/linux/bug.h
of Linux 4.4.
I did not import BUILD_BUG_ON_MSG() because it would not work if it
is used with include/common.h in U-Boot. I'd like to postpone it
until the root cause (the "error()" macro in include/common.h causes
the name conflict with "__attribute__((error()))") is fixed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add function to poll register waiting for specific bit(s).
Similar functions are implemented in few drivers - they are almost
identical and can be generalized.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is already defined in ide.h, which part.h includes. So we don't need
the duplicate typedef. At least with my old blackfin gcc 4.3.5 tool chain,
this causes an error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
This commit 4bdcbe60a1 removes reset_cpu
which breaks SPL build when DEBUG macro defined.
"
arch/arm/lib/built-in.o: In function `do_reset':
~/uboot/arch/arm/lib/reset.c:45: undefined reference to `reset_cpu'
scripts/Makefile.spl:244: recipe for target 'spl/u-boot-spl' failed
"
Enable CONFIG_SPL_WATCHDOG_SUPPORT to fix this issue.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Eric Nelson <eric@nelint.com>
Add pinmux settings.
Add related macro definitions.
Nand pin conflicts with emmc, so if want to enable nand, need to do
hardware rework. After hardware rework, define CONFIG_NAND_MXS in
board header file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Support uncompressing zImage which is larger than 8M.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Peter Robinson <pbrobinson@gmail.com>
Cc: Volodymyr Riazantsev <volodymyr.riazantsev@globallogic.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
To i.MX6UL 14x14 EVK, system memory is 512M; to i.MX6UL 9x9 EVK,
system memory is 256M. If setting mtest size to 256M, mtest will
crash uboot for i.MX6UL 9x9 evk. So change mtest size to 128M.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add a uclass ID for a disk controller. This can be used by AHCI/SATA or
other controller types. There are no operations and no interface so far,
but it is possible to probe a SATA device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a uclass for the northbridge / SDRAM controller found on some older
Intel chipsets.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this BIOS emulator uses a bus/device/function number. Change
it to use a device if CONFIG_DM_PCI is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We have a way to find a regmap by its syscon driver data value. Add the same
for syscon itself.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We use driver model for this now, so we don't need this string.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present interrupt routing is set up from arch_misc_init(). We can do it
a little later instead, in interrupt_init().
This removes the manual pirq_init() call. Where the platform does not have
an interrupt router defined in its device tree, no error is generated. Some
platforms do not have this.
Drop pirq_init() since it is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
It seems likely that at some point we will want a generic interrupt uclass.
But this is a big undertaking as it involves unifying code across multiple
architectures.
As a first step, create a simple IRQ uclass and a driver for x86. This can
be generalised later as required.
Adjust pirq_init() to probe this driver, which has the effect of creating
routing tables and setting up the interrupt routing. This is a start
towards making interrupts fit better with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At some point we may need to distinguish between different types of PCHs,
but for existing supported platforms we only need to worry about version 7
and version 9 bridges. Add a driver for the PCH7.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
A Platform Controller Hub is an Intel concept - it is like the peripherals
on an SoC and is often in a separate chip from the CPU. The chip is typically
found on the first PCI bus and integrates multiple devices.
We have a very simple uclass to support PCHs. Add a few operations, such as
setting up the devices on the PCH and finding the SPI controller base
address. Also move it into drivers/pch/ since we will be adding a few PCH
drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a driver-model version of the pci_write_bar32 function so that this is
supported in the new API.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The testpattern of the lcd was only working in 8bit mode(2x3 tiles in
different colors). With this patch now 8bit and 16bit is supported.
In 16bit mode there are 2x4 tiles in different colors.
The number of LCD-colors is defined in the include/configs/<boardfile>.h
Signed-off-by: Andreas Neubacher <neubacher.andreas@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch adds driver support for the Realtek RTL8152B/RTL8153 USB
network adapters.
Signed-off-by: Ted Chen <tedchen at realtek.com>
[swarren, fixed a few compiler warnings]
[swarren, with permission, converted license header to SPDX]
[swarren, removed printf() spew during probe()]
Signed-off-by: Stephen Warren <swarren at nvidia.com>
Now that the DWC2 driver supports split transactions, we can reasonably
enable support for USB keyboards. This wasn't terribly useful before
since keyboards are usually LS/FS devices, and thus require split
transaction support when attached to a USB hub such as the hub built into
the RPi model Bs.
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
This board includes an RK3288 SoC on a SOM. It can be mounted on a
base-board which provides a wide range of peripherals.
So far this is verified to boot to a prompt from a microSD card. The serial
console works as well as HDMI.
Thanks to Tom Cubie for sending me a board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable these devices using the VOPL video output device. We explicitly
disable VOPB in the device tree to avoid it taking over. Since this device
has an LCD display this comes up by default. If the display fails for some
reason then it will attempt to use HDMI. It is possible to force it to fail
(and thus fall back to HDMI) by puting 'return -EPERM' at the top of
rk_edp_probe(). For now there is no easy way to select between the two.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a feature which speeds up the CPU to full speed in SPL to minimise
boot time. This is only supported for certain boards (at present only
jerry).
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the low-level init is skipped on rockchip. Among other things
this means that the instruction cache is left disabled. Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current DisplayPort uclass is too specific. The operations it provides
are shared with other types of output devices, such as HDMI and LVDS LCD
displays.
Generalise the uclass so that it can be used with these devices as well.
Adjust the uclass to handle the EDID reading and conversion to
display_timing internally.
Also update nyan-big which is affected by this.
Signed-off-by: Simon Glass <sjg@chromium.org>
LCD panels can usefully be modelled as their own uclass. They can be probed
(which powers them up ready for use). If they have a backlight, this can be
enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
LCD panels normally have a backlight which can be controlled to illuminate
the LCD contents. Add a uclass to support this. Initially it only has a
method to enable the backlight.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a uclass that supports Pulse Width Modulation (PWM) devices. It
provides methods to enable/disable and configure the device.
Signed-off-by: Simon Glass <sjg@chromium.org>
We must use the console name in the 'stdout' variable to select the one
we want. At present the name is formed from the driver name with a suffix
indicating the rotation value.
It seems better to name them sequentially since this can be controlled by
driver order. So adjust the code to use 'vidconsole' for the first,
'vidconsole1' for the second, etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is sometimes useful to be able to find a device before probing it,
perhaps to set up some platform data for it. Allow finding by of_offset
also.
Signed-off-by: Simon Glass <sjg@chromium.org>
GPIO drivers want to be able to show if a pin is enabled for input, output,
or is being used by another function. Some drivers can easily find this
and the code is included in the driver. For some SoCs this is more complex.
Conceptually this should be handled by pinctrl rather than GPIO. Most
pinctrl drivers will have this feature anyway.
Add a method by which a GPIO driver can obtain the pin mux value given a
GPIO reference. This avoids repeating the code in two places.
Signed-off-by: Simon Glass <sjg@chromium.org>
To reduce the SPL image size, drop the LED features. Jerry does not have
an LED and we can leave out GPIO support also.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is defined in the device tree in Linux. Copy over the settings so that
this can be used instead of hard-coding the reset line.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some devices need special sequences to be used when starting up. Add a
uclass for this. Drivers can be added to provide specific features as
needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This Rockchip PMIC provides features suitable for battery-powered
applications. It is commonly used with Rockchip SoCs.
Add a driver which provides register access. The regulator driver will use
this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function which produces a flags word from a few common PIN_CONFIG
settings. This is useful for simple pinctrl drivers that don't need to worry
about drive strength, etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
There's a 64K reserved area at the end of the first 4M.
Store env there, so we can use fastboot to flash it.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
We will save boot mode flag in grf's os_reg[4], if fastboot
requested or fastboot key pressed, try to enter fastboot mode
at preboot stage.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a method which can locate a clock for a device, given its index. This
uses the normal device tree bindings to return the clock device and the
first argument which is normally used as a peripheral ID in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: Minor cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
applied with fixing 2 checkpatch warnings:
WARNING: please, no space before tabs
Signed-off-by: Heiko Schocher <hs@denx.de>
Add a test for the 'bmp' command. Test both the uncompressed and compressed
versions of the file, since they use different code paths.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Add tests that check that the video console is working correcty. Also check
that text output produces the expected result. Test coverage includes
character output, wrapping and scrolling.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Now that driver model support is available, convert sandbox over to use it.
We can remove a few of the special hooks that sandbox currently has.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Move this option to Kconfig. This is quite simple as only sandbox uses the
driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Before relocation we need to reserve memory for the video driver frame
buffers so that they can use this memory when they start up (after
relocation). Add a call to the uclass to permit this.
The current top and bottom of the region is stored in global_data so that
it can be checked post-relocation to ensure enough memory is available. No
video device should be probed before relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
The existing LCD/video interface suffers from conflating the bitmap display
with text output on that display. As a result the implementation is more
complex than it needs to me.
We can support multiple text console drivers. Create a separate uclass to
support this, with its own API.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
The LCD functions and definitions are not used with the driver model video
uclass. When all boards are converted over we can remove the file. For now,
use #ifdef to omit the contents.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
U-Boot has separate code for LCDs and 'video' devices. Both now use a
very similar API thanks to earlier work by Nikita Kiryanov. With the driver-
model conversion we should unify these into a single uclass.
Unfortunately there are different features supported by each. This
implementation provides for a common set of features which should serve
most purposes. The intent is to support:
- bitmap devices with 8, 16 and 32 bits per pixel
- text console wih white on black or vice versa
- rotated text console
- bitmap display (BMP format)
More can be added as additional boards are ported over to use driver model
for video.
The name 'video' is chosen for the uclass since it is more generic than LCD.
Another option would be 'display' but that would introduce a third concept
to U-Boot which seems like the wrong approach.
The existing LCD and video init functions are not needed now, so this uclass
makes no attempt to implement them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
LPUART is seen on Freescale VF610 and QorIQ Layerscape devices.
Create a Kconfig option and move it to defconfig for all boards
that have this serial driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Simon Glass <sjg@chromium.org>
Convert ls1021atwr_nor to driver model support. As a start, enable
ns16550 serial port driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The most basic thing for clock is to enable it, but it is missing
in this uclass.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
This header uses ulong, so it needs to include <linux/types.h>.
Likewise, "struct udevice" must be declared before it is used.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
The comment about get_periph_rate() is the same as that of
set_periph_rate().
I am fixing typos here and there while I am in this file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add the missing code to allow bzip2 compression to be used. This is useful
for sandbox tests. These files are taken from the bzip2 1.0.6 release.
The license text is copied to the top of each file as is done with other
bzip2 files in U-Boot. The only other change is to squash a compiler warning
with nBytes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since OMAP's spl doesn't support DM currently, do not define
CONFIG_TIMER for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since OMAP's spl doesn't support DM currently, do not define
CONFIG_TIMER for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since OMAP's spl doesn't support DM currently, do not define
CONFIG_TIMER for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adding timer init function in timer-uclass driver to create and
initialize the timer device on platforms where u-boot,dm-pre-reloc
is not used. Since there will be multiple timer devices in the
system, adding a tick-timer node in chosen node to know which
timer device to be used as tick timer in u-boot.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
The iocon and bamboo boards are often on the verge of, or going over,
their allowed size limits depending on toolchain used. If we turn off
CONFIG_SYS_LONGHELP we can gain approximately 14KiB back.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Remove duplicated SDRAM_INTERVAL_BSTOPRE from mpc83xx.h,
which has been defined in fsl_ddr_sdram.h
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
The patch removes some macros that are not used.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Enric Balletbo Serra <enric.balletbo@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Symbol is already defined in ti_armv7_common.h which is included
via ti_armv7_omap.h
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
We can delete board/pb1x00/config.mk by moving the define of
CONFIG_SYS_TEXT_BASE to somewhere else. Other MIPS boards are
still defining it in include/config/${BOARD}.h, so I am following
that way here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
We can delete board/dbau1x00/config.mk by moving the define of
CONFIG_SYS_TEXT_BASE to somewhere else. Other MIPS boards are
still defining it in include/config/${BOARD}.h, so I am following
that way here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
We can delete board/micronas/vct/config.mk by moving the define of
CONFIG_SYS_TEXT_BASE to somewhere else. Other MIPS boards are
still defining it in include/config/${BOARD}.h, so I am following
that way here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The board/freescale/m54418twr/config.mk defined TEXT_BASE, which has
the same value as CONFIG_SYS_TEXT_BASE. The TEXT_BASE is referenced
by two files:
- arch/m68k/cpu/mcf5445x/start.S and include/
- include/configs/M54418TWR.h
Replace the references with CONFIG_SYS_TEXT_BASE and delete
board/freescale/m54418twr/config.mk.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Angelo Dureghello <angelo at sysam.it>
The load address of the kernel can be changed via "kernel_addr_r"
environment. The device tree and the initramdisk should be relocated
according to the kernel location.
The "bootm_low" should be calculated by masking the lower bits
(TEXT_OFFSET part) of the "kernel_addr_r" environment value.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
U-Boot relocates the device tree and the initramdisk to the tail
of the memory region before booting the kernel.
Some UniPhier boards are equipped with a large amount of memory.
For those boards, the device tree and the initramdisk are placed out
of the the kernel causing a kernel panic.
Add CONFIG_SYS_BOOTMAPSZ to prevent them from going too high.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This commit adds the psci.h header file from Linux kernel
which contains definitions related to the PSCI interface provided
by firmware
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enabling this function always removes some class of string saftey issues.
The size change here in general is about 400 bytes and this seems a reasonable
trade-off.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
config.h is used in target and host code and therefore should not
pull in target header files to avoid compile errors. This change
is also required for the MIPS header file sync done in follow-up
patches.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.
Simple uses of sprintf are also converted to use strcpy.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
