Commit graph

17022 commits

Author SHA1 Message Date
Mike Frysinger
47fde91f0c global_data: unify global flag defines
All the global flag defines are the same across all arches.  So unify them
in one place, and add a simple way for arches to extend for their needs.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-08-09 21:46:32 +02:00
Andy Fleming
033220e7a4 MAKEALL: Allow empty ERR directory
If we build everything correctly with multiple builds, and an
ERR directory had been previously created, we failed to report
that everything was fine because grep failed to find anything
in the ERR directory. Use grep -r, which doesn't complain if
there are no input files.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Tested-by: Tom Rini <trini@ti.com>
2012-08-09 21:22:05 +02:00
Wolfgang Denk
1d56f63dab Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
* 'master' of git://git.denx.de/u-boot-mpc85xx:
  powerpc/85xx: use CONFIG_SYS_FSL_PCIE_COMPAT macro when setting the PCI LIODNs
  powerpc/mpc85xx: Ignore E bit for BSC9130/1
  powerpc/sgmii: To support PHY link state auto detect in SGMII mode
  powerpc/85xx: improve definition of BR_PHYS_ADDR macro
  powerpc/p2041: configure the CPLD lane_mux according to RCW
  powerpc/ddr: fix fsl_ddr_get_dimm_params compile error
  powerpc/corenet: fix compile error when CONFIG_SYS_NO_FLASH is defined
  powerpc/mpc8xxx: fix workaround for errata DDR111 and DDR134 for DDR over 4GB
  powerpc/p1022ds: fix DIU/LBC switching with NAND enabled
  powerpc/p1022ds: add support for SPI and SD boot

Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-08-09 21:04:05 +02:00
Timur Tabi
5c5befda58 powerpc/85xx: use CONFIG_SYS_FSL_PCIE_COMPAT macro when setting the PCI LIODNs
The SET_PCI_LIODN() macro takes a compatible property string as a parameter, so that it knows
which PCI device tree node to look for.  The calls to these macros are using a hard-coded string,
but we already have the CONFIG_SYS_FSL_PCIE_COMPAT macro which contains the same string, so we
should use that.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-08 18:32:16 -05:00
York Sun
718f2b3187 powerpc/mpc85xx: Ignore E bit for BSC9130/1
Commit 48f6a5c34 removed E bit. BSC9130/1 were left out due to patch apply
timing. Remove them now.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-08 18:32:16 -05:00
Hongtao Jia
308bc61db7 powerpc/sgmii: To support PHY link state auto detect in SGMII mode
PHYs on SGMII riser card are used in SGMII mode with different external
IRQs from eTSEC. This means in SGMII mode phy-handle and phy-connection-type
under ethernet node should be updated. Otherwise the PHY interrupt can not
be handled therefor PHY link state change can not be auto detected.

For we have seperate SGMII PHY nodes, ethernet PHY reg fixup is not needed
but it's still be kept to guarantee the sgmii mode could work with old
device tree.

Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-08 18:32:15 -05:00
Timur Tabi
7ee411071f powerpc/85xx: improve definition of BR_PHYS_ADDR macro
The BR_PHYS_ADDR(x) macro was missing parentheses around "x" in the macro
definition, so callers had to supply their own parenthesis.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-08 18:32:15 -05:00
Shaohui Xie
145dbc0250 powerpc/p2041: configure the CPLD lane_mux according to RCW
Lane muxing on p2041 is controlled by a reg in CPLD, offset of this reg
is 0xc, CPLD supports SATA by default, we should re-configure the lane
muxing according to RCW, which indicates what SerDes protocol it is running.

Default lane muxing map is as below:
Lane G on bank1 routes to SGMII, controlled by bit 1 of the reg;
Lane A on bank2 routes to AURORA, controlled by bit 0 of the reg;
Lane C/D on bank2 routes to SATA0 and SATA1, controlled by bit 2
and bit 3 respectively.

Default value of these bits for lane muxing is '1', we should set or clear
these bits accoring to RCW.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-08 17:13:39 -05:00
Shaohui Xie
98de369b1c powerpc/ddr: fix fsl_ddr_get_dimm_params compile error
fsl_ddr_get_dimm_params() should be wrapped by
CONFIG_SYS_DDR_RAW_TIMING, otherwise, when using fixed_sdram() instead of
using SPD, it will cause compile error.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-08 17:13:38 -05:00
Shaohui Xie
0f57f6a3fe powerpc/corenet: fix compile error when CONFIG_SYS_NO_FLASH is defined
ENV location compile logic is wrong, and when CONFIG_SYS_NO_FLASH is defined
and non-NOR u-boot is building, it will cause compile error. Also, add
CONFIG_SYS_FLASH_USE_BUFFER_WRITE for p2041, which will improve NOR flash
write performance.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-08 17:13:38 -05:00
York Sun
535a159ab6 powerpc/mpc8xxx: fix workaround for errata DDR111 and DDR134 for DDR over 4GB
The fix for errata workaround is to avoid covering physical address
0xff000000 to 0xffffffff during the implementation. Early commit eb672e92
works until DDR size exceeds 4GB. This fix works for DDR size up to 64GB.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-08 17:13:38 -05:00
Timur Tabi
7a946961c7 powerpc/p1022ds: fix DIU/LBC switching with NAND enabled
In order for indirect mode on the PIXIS to work properly, both chip selects
need to be set to GPCM mode, otherwise writes to the chip select base
addresses will not actually post to the local bus -- they'll go to the
NAND controller instead.  Therefore, we need to set BR0 and BR1 to GPCM
mode before switching to indirect mode.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-08 17:13:37 -05:00
Matthew McClintock
af2536088e powerpc/p1022ds: add support for SPI and SD boot
Add TLB mappings, board target options, and configuration items
need for SPI/SD boot.

Since P1022DS RevB board, the NOR flash have been changed to 16 bit/28bit
address flash, therefore, when SDHC/ESPI booting and access to eLBC,
the PMUXCR[0~1] must be set to 10b, and PMUXCR[9~10] must be set to
00b for them.

Configure the PX_BRDCFG0[0~1] to 10b which is connected to
SPI devices as SPI_CS(0:3)_B.

Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-08 17:13:37 -05:00
Nobuhiro Iwamatsu
d764c5043d sh: Add support pin function control using GPIO
Renesas SH and R-Mobile set up device using PFC.
This provide the framework. Most codes were brought from linux kernel.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-08-08 10:24:41 +09:00
Hideyuki Sano
d61678e096 serial: sh: Add support Renesas R8A7740
The serial device of R8A7740 has the same structure as SH7372 of SH, etc.

Signed-off-by: Hideyuki Sano <hideyuki.sano.dn@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-08-08 09:52:06 +09:00
Nobuhiro Iwamatsu
c3d6a35732 serial: sh: Add support Renesas SH73A0
The serial device of SH73A0 has the same structure as SH7372 of SH, etc.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-08-08 09:52:03 +09:00
Yoshihiro Shimoda
d185857267 sh: modify checkcpu() for SH-4A
Even if using CPU is SH-4A, the previous code always put "SH4".
This patch fixes it.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-08-08 09:50:41 +09:00
Wolfgang Denk
6d36121b87 Merge branch 'master' of git://git.denx.de/u-boot-onenand
* 'master' of git://git.denx.de/u-boot-onenand:
  env_onenand: set ONENAND_MAX_ENV_SIZE to CONFIG_ENV_SIZE

Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-08-07 23:42:55 +02:00
Holger Brunck
157ef7993d MAINTAINERS: cleanup for km ppc boards
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
2012-08-07 23:11:40 +02:00
Michal Simek
968766a7e8 spi: Fix merge conflicts - Makefile
The patch "spi: tegra2: rename tegra2_spi.* to tegra_spi.*"
(sha1: edffa63d3d)
renamed tegra2_spi.c to tegra_spi.c

and the patch "Merge branch 'master' of git://git.denx.de/u-boot-microblaze"
(sha1: d978780b2e)

has wrongly resolved confict.

This patch fix it.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2012-08-07 23:08:14 +02:00
Tom Rini
94c1a20fe7 ext2fs: fix warning: 'blocknxt' may be used uninitialized with gcc 4.2
The above warning was introduced originally in 436da3c "ext2load:
increase read speed" and fixed for newer toolchains in b803273 "ext2fs:
fix warning: 'blocknxt' may be used uninitialized".  This change did not
fix the warning with gcc 4.2, as found in ELDK 4.2.

If we rework the while loop to initalize blocknxt before entering the
warning really goes away.  Tested on am335x with an approx 7mb file and
crc32 in U-Boot befor and after this change.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Jason Cooper <u-boot@lakedaemon.net>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-08-07 20:52:42 +02:00
David du Colombier
034afbcc16 env_onenand: set ONENAND_MAX_ENV_SIZE to CONFIG_ENV_SIZE
This fix prevents env_import() CRC to fail when CONFIG_ENV_SIZE
is not equal to 4096 bytes
It also prevents mtd->read and mtd->write to be incomplete when
the environment is larger than 4096 bytes.

Signed-off-by: David du Colombier <0intro@gmail.com>
2012-08-06 10:38:47 +02:00
Gerlando Falauto
56249fea3d powerpc/82xx: adapt SDRAM settings for mgcoge3ne
The HW guys suggested to change these two values. And these values are
now identical to the values we use on mgcoge.

PSDMR_WRC was set to 1C as it should lead to better performance.

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2012-07-31 22:36:38 +02:00
Gerlando Falauto
c9718210b1 powerpc/82xx: use SDRAM detection for mgcoge2ne
mgcoge2ne was an intermediate step towards mgcoge3ne. One difference is the
smaller SDRAM on mgcoge2ne (128MB). To support both boards with the same
u-boot we use here the SDRAM detection.

This patch enables SDRAM detection between 256MB and 128MB.
So in addition to the existing 256MB geometry:
     4 chips x 8M (13 rows, 10 cols) x 16 bit x 4 banks
we can now also have 128MB geometry:
     4 chips x 4M (13 rows,  9 cols) x 16 bit x 4 banks

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
2012-07-31 22:36:35 +02:00
Gerlando Falauto
3a532346fc powerpc/82xx: add SDRAM detection for km82xx
This patch adds SDRAM detection feature to km82xx boards.
To enable this feature, define CONFIG_SYS_SDRAM_LIST as the initializer
for an array of struct sdram_conf_s.
These structs will expose the bitfields within registers PSDMR and OR1 which
have to be different between configurations; common bitfields will be
defined, as usual, within CONFIG_SYS_PSDMR and CONFIG_SYS_OR1.
If CONFIG_SYS_SDRAM_LIST is not defined, then the usual behavior is retained.

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
2012-07-31 22:36:31 +02:00
Gerlando Falauto
65c7f92313 powerpc/82xx: move km/km82xx-common.h within km82xx.h
The only file including km82xx-common.h is km82xx.h.
So there is no need to have it as a separate file.

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
2012-07-31 22:36:27 +02:00
Gerlando Falauto
b83cf848f0 powerpc/82xx: merge mgcoge.h and mgcoge3ne.h into km82xx.h
Since mgcoge and mgcoge3ne are the only km82xx boards, there is no need
to keep them as separate .h config files.
Therefore, make mgcoge3ne.h and mgcoge.h converge into a single km82xx.h
file.

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
2012-07-31 22:36:23 +02:00
Gerlando Falauto
bae5407dd2 powerpc/82xx: move mgcoge, mgcoge3ne defines to ease subsequent merge
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
2012-07-31 22:30:01 +02:00
Holger Brunck
4fdfe376eb powerpc/82xx: remove unused define for mgcoge3ne
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
2012-07-31 22:29:44 +02:00
Zhong Hongbo
b420cbb625 SMDK6400: Add MAINTAINERS entry
Signed-off-by: Zhong Hongbo <bocui107@gmail.com>
2012-07-31 22:27:39 +02:00
Wolfgang Denk
948fa1713c Merge branch 'master' of git://git.denx.de/u-boot-i2c
* 'master' of git://git.denx.de/u-boot-i2c:
  km/common: remove printfs for i2c deblocking code
  CONFIG: SMDK5250: I2C: Enable I2C
  I2C: Add support for Multi channel
  I2C: Modify the I2C driver for EXYNOS5
  I2C: Move struct s3c24x0_i2c to a common place.
  EXYNOS: PINMUX: Add pinmux support for I2C
  EXYNOS5: define EXYNOS5_I2C_SPACING
  EXYNOS: Add I2C base address.
  EXYNOS: CLK: Add i2c clock
  mx6qsabrelite: add i2c multi-bus support
  imx-common: add i2c.c for bus recovery support
  i.mx53: add definition for I2C3_BASE_ADDR
  i.mx: iomux-v3.c: move to imx-common directory
  i.mx: iomux-v3.h: move to imx-common include directory
  iomux-v3: remove include of mx6x_pins.h
  mxc_i2c: finish adding CONFIG_I2C_MULTI_BUS support
  mxc_i2c: add bus recovery support
  mxc_i2c: prep work for multiple busses support
  mxc_i2c: add i2c_regs argument to i2c_imx_stop
  mxc_i2c: add retries
  mxc_i2c: check for arbitration lost
  mxc_i2c: change slave addr if conflicts with destination.
  mxc_i2c: don't disable controller after every transaction
  mxc_i2c: place i2c_reset code inline
  mxc_i2c: place imx_start code inline
  mxc_i2c: remove redundant read
  mxc_i2c: combine i2c_imx_bus_busy and i2c_imx_trx_complete into wait_for_sr_state
  mxc_i2c.c: code i2c_probe as a 0 length i2c_write
  mxc_i2c: call i2c_imx_stop on error in i2c_read/i2c_write
  mxc_i2c: create i2c_init_transfer
  mxc_i2c: clear i2sr before waiting for bit
  mxc_i2c: create tx_byte function
  mxc_i2c: remove ifdef of CONFIG_HARD_I2C
  mxc_i2c: fix i2c_imx_stop
  i2c: deblock i2c bus also if accessed before realocation

Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-07-31 22:07:42 +02:00
Wolfgang Denk
d978780b2e Merge branch 'master' of git://git.denx.de/u-boot-microblaze
* 'master' of git://git.denx.de/u-boot-microblaze:
  microblaze: Wire up SPI driver
  spi: microblaze: Adds driver for Xilinx SPI controller
  microblaze: intc: Clear interrupt code
  microblaze: Call serial multi initialization
  microblaze: Move __udelay implementation
  microblaze: Remove extern from board.c
  microblaze: Wire up dts configuration
  fdt: Add board specific dts inclusion
  microblaze: Move individual board linker scripts to common script in cpu tree.
  microblaze: Add gpio.h
  microblaze: Add missing undefs for UBI and UBIFS
  microblaze: Expand and correct configuration comments
  microblaze: Enable ubi support
  microblaze: Avoid compile error on systems without cfi flash
  microblaze: Remove wrong define CONFIG_SYS_FLASH_PROTECTION

Conflicts:
	drivers/spi/Makefile

Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-07-31 22:01:08 +02:00
Holger Brunck
e69e482bbf km/common: remove printfs for i2c deblocking code
This code will also be used before reallocation and during this time we
are not allowed to do these printings.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
2012-07-31 08:04:13 +02:00
Rajeshwari Shinde
c82b050ead CONFIG: SMDK5250: I2C: Enable I2C
This enables I2C support on smdk5250.
Pinmux setting moved to board file to avoid repeated setting of
gpio lines.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-07-31 08:03:19 +02:00
Rajeshwari Shinde
178239de19 I2C: Add support for Multi channel
This adds multiple i2c channel support for I2C.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-07-31 08:03:03 +02:00
Rajeshwari Shinde
ab7e52bb24 I2C: Modify the I2C driver for EXYNOS5
This patch modifies the S3C I2C driver to suppport EXYNOS5.
The cahnges made to driver are as follows:
        - I2C base address is passed as a parameter to many
        functions to avoid multiple #ifdef
        - Channel initialisation is moved to a commom funation
        as it is required by i2c_init.
        - Hardcoding for I2CCON_ACKGEN removed.
        - Replaced printf with debug.
        - Checkpatch issues resolved.
        - Pinmux setting will be done in board/samsung/smdk5250/smdk5250.c
        to avoid repeated setting of gpio lines, as it have multi bus support.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-07-31 08:02:51 +02:00
Rajeshwari Shinde
91dffb16ff I2C: Move struct s3c24x0_i2c to a common place.
struct s3c24x0_i2c is being moved to common local header file so that
the same can be used by s3c series and exynos series SoCs.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-07-31 08:02:41 +02:00
Rajeshwari Shinde
c65c05f57f EXYNOS: PINMUX: Add pinmux support for I2C
This patch adds pinmux code for I2C.

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-07-31 08:02:28 +02:00
Rajeshwari Shinde
8da3eb1b22 EXYNOS5: define EXYNOS5_I2C_SPACING
This patch defined EXYNOS5_I2C_SPACING used to calculate I2C channel
base address.

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-07-31 08:02:07 +02:00
Rajeshwari Shinde
1a758aec3d EXYNOS: Add I2C base address.
This patch adds the base address for I2C.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-07-31 08:01:56 +02:00
Rajeshwari Shinde
989feb8c52 EXYNOS: CLK: Add i2c clock
This adds i2c clock information for EXYNOS5.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-07-31 08:01:32 +02:00
Troy Kisky
9c06782863 mx6qsabrelite: add i2c multi-bus support
This includes bus recovery support.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Jason Liu <r64343@freescale.com>
2012-07-31 08:01:09 +02:00
Troy Kisky
cc54a0f7cc imx-common: add i2c.c for bus recovery support
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 08:00:57 +02:00
Troy Kisky
df369dcdb0 i.mx53: add definition for I2C3_BASE_ADDR
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 08:00:44 +02:00
Troy Kisky
18c0ad27c1 i.mx: iomux-v3.c: move to imx-common directory
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 08:00:32 +02:00
Troy Kisky
af2a35fb1f i.mx: iomux-v3.h: move to imx-common include directory
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 08:00:19 +02:00
Troy Kisky
d3394ec198 iomux-v3: remove include of mx6x_pins.h
This include is not needed.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Jason Liu <r64343@freescale.com>
2012-07-31 07:59:56 +02:00
Troy Kisky
9815326d04 mxc_i2c: finish adding CONFIG_I2C_MULTI_BUS support
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 07:59:41 +02:00
Troy Kisky
96c19bd3ef mxc_i2c: add bus recovery support
Add support for calling a function that will toggle the
SCL line to return the bus to idle condition.

The actual toggling function is added in a later patch.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 07:59:26 +02:00
Troy Kisky
e4ff525f91 mxc_i2c: prep work for multiple busses support
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 07:57:04 +02:00