Commit graph

983 commits

Author SHA1 Message Date
Stefan Agner
8fca2d8cb8 mtd: vf610_nfc: enable ONFI detection
This changes enable ONFI detection. The Read ID command now allows
one address byte which is needed for ONFI detection. To read the
ONFI parameter page, the NAND_CMD_PARAM need to be supported. The
CMD code enables one command and one address byte along with reading
data from flash using R/B#, as specified by ONFI.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-05-24 14:27:46 -05:00
Stefan Agner
080a71e8e9 mtd: vf610_nfc: add 32-error correction option for HW ECC
Add option to choose between current 24-error correction and 32-error
correction through Kconfig. 32-error correction allow to use NAND
chips which require up to 8-bit error correction per 512 byte (when
using 2K pages).

Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-05-24 14:27:46 -05:00
Stefan Agner
5519194d4f mtd: vf610_nfc: add Freescale NFC controller configs to Kconfig
This commit allows users to enable/disable the Freescale NFC
controller found in systems like Vybrid (VF610), MPC5125, MCF54418
or Kinetis K70 via Kconfig with more detailed help docs.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefano Babic <sbabic@denx.de>
[scottwood: updated vf610twr_nand_defconfig]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-05-24 14:27:28 -05:00
Stefan Agner
84d656a283 mtd: vf610_nfc: use in-band bad block table
Use in-band bad block table (NAND_BBT_NO_OOB) which allows to
use the full OOB for hardare ECC purposes. Since there is no
ECC correction on the OOB it is also safer to use in-band area
to store the bad block table marker.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-05-24 14:26:55 -05:00
Stefan Agner
5dec286b82 mtd: vf610_nfc: implement OOB only read
Implement read of OOB area only. When using column and sector size
properties, only parts of the page can be read. However, this works
only when hardware ECC is disabled, otherwise the ECC engine would
ruin the data in the buffer. To allow OOB only reads, three points
had to be addressed:
- Set ECC mode per command.
- Handle NAND_CMD_READOOB seperate. Make sure column and sector
  size is correctly set up, while disabling ECC.
- Now, the OOB data end up at the beginning of the buffer. Remove
  the special handling of OOB (spareonly).

Especially bad block scans benefit from this change. On a 512MiB
SLC NAND device, the bad block scan took 1.5s less than before.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-05-24 14:26:55 -05:00
Stefan Agner
d111bf99a8 mtd: vf610_nfc: allow bitflips in an empty page
Allow bit flips in a empty page up to half of the recoverable
bits (strength / 2).

Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-05-24 14:26:54 -05:00
Stefan Agner
6fcfd1e890 mtd: vf610_nfc: remove read on SEQIN
Since we do not support sub-page writes anyway, reading the page
back to the controller on SEQIN command is not required. Remove
the page read on SEQIN.

However, the column/page values relevant to the SEQIN command, hence
set the column/row address on SEQIN command.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-05-24 14:26:54 -05:00
Stefan Agner
f55bc296a8 mtd: vf610_nfc: remove caching of page in buffer
To improve performance we remember the current page in the buffer
and avoid reading it twice. This implicit page cache increases
complexity while does not increase performance in real world cases.
This patch removes that feature.

Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-05-24 14:26:54 -05:00
Jörg Krause
1fbdb70610 mtd: nand: mxs: Replace magic number for bits per ECC level with macro
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Reviewed-by: Marek Vasut <marex@denx.de>
2015-05-24 14:26:54 -05:00
Peng Fan
bd38da1a55 mtd:mxs:nand calculate ecc strength dynamically
Calculate ecc strength according oobsize, but not hardcoded
which is not aligned with kernel driver

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <b37916@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
2015-05-24 14:26:54 -05:00
Raghav Dogra
6b8583b0ad nand/elbc: Memory leak fix
Freeing allocated memory to priv before returning
from the function

Signed-off-by: Raghav Dogra <raghav@freescale.com>
[scottwood: removed unnecessary cast]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-05-22 15:45:51 -05:00
Stephen Warren
5e856fa8be nand: fix buffer alignment in new verification feature
On systems with caches enabled, NAND I/O may need to flush/invalidate
the cache during read/write operations. For this to work correctly, all
buffers must be cache-aligned. Fix nand_verify*() to allocate aligned
buffers.

This prevents cache alignment warnings from being spewed when using
U-Boot to write an updated version of itself to flash on NVIDIA Tegra
Seaboard (after perturbation of stack/data layout in current
u-boot-dm/next branch).

I have validatd (executed) nand_verify(), but I don't think I've executed
nand_verify_page_oob(); testing of that would be useful.

Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Fixes: 59b5a2ad83 ("nand: Add verification functions")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Scott Wood <scottwood@freescale.com>
2015-05-21 14:24:36 -05:00
Simon Glass
832adb212e sandbox: spi: Add newline to printf() in sandbox_sf_probe
This printf() should have a newline at the end. Add it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-05-14 18:49:35 -06:00
Haikun.Wang@freescale.com
a5e1bcdeeb dm: sf: Update default name of spi flash in structure udevice
Default name of spi flash like this "0:0", update it to "spi_flash@0:0".

Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-05-06 14:00:35 -06:00
Tom Rini
cc555bd4f4 Merge branch 'master' of git://git.denx.de/u-boot-spi 2015-04-28 07:28:43 -04:00
Jagannadha Sutradharudu Teki
c650ca7b4c sf: Fix to compute proper sector_size
Upto now flash sector_size is assigned from params which isn't
necessarily a sector size from vendor, so based on the SECT_*
flags from flash_params the erase_size will compute and it will
become the sector_size finally.

Bug report (from Bin Meng):
=> sf probe
SF: Detected SST25VF016B with page size 256 Bytes, erase size 4 KiB,
total 2 MiB, mapped at ffe00000

=> sf erase 0 +100
SF: 65536 bytes @ 0x0 Erased: OK

Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2015-04-28 13:31:36 +05:30
Bin Meng
074eed5146 dm: sf: Make SST flash write op work again
With SPI flash moving to driver model, commit fbb0991 "dm: Convert
spi_flash_probe() and 'sf probe' to use driver model" ignored the
SST flash-specific write op (byte program & word program), which
actually broke the SST flash from wroking.

This commit makes SST flash work again under driver model, by adding
SST flash-specific handling in the spi_flash_std_write().

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2015-04-28 13:31:24 +05:30
Bin Meng
be7be78e10 dm: sf: Save flash flags to struct spi_flash
Add a new member 'flags' in struct spi_flash to store the flash flags
during spi_flash_validate_params().

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2015-04-28 13:29:54 +05:30
Scott Wood
b2d5ac5985 armv8/ls2085aqds: NAND boot support
This adds NAND boot support for LS2085AQDS, using SPL framework.
Details of forming NAND image can be found in README.

Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23 16:46:50 -07:00
Jaiprakash Singh
39b0bbbb23 driver/ifc: Add 64KB page support
IFC has two register pages.Till IFC version 1.4 each
register page is 4KB each.But IFC ver 2.0 register page
size is 64KB each.IFC regiters structure is break into
two viz FCM and RUNTIME.FCM(Flash control machine) registers
are defined in PAGE0 and controls IFC generic functionality.
RUNTIME registers are defined in PAGE1 and controls NAND and
GPCM funcinality.

FCM and RUNTIME structures defination is common for IFC
version 1.4 and 2.0.

Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23 16:46:50 -07:00
Scott Wood
585acc9de6 nand/fsl_ifc: Increase eccstat[] for IFC 2.0
IFC 2.0 doubled the SRAM size, which means double the number of
ECCSTAT registers.  Fix the resulting array overflow.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-23 08:55:53 -07:00
Jagannadha Sutradharudu Teki
122d805fd4 Revert "spi: add config option to enable the WP pin function on st micron flashes"
This reverts commit 562f8df18d.

Note: Even un-reverting this patch couldn't works as expected, based
on the latest testing from Heiko Schocher.

Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
2015-04-23 19:53:29 +05:30
Peng Fan
4fbad92e73 mtd: spi: check return value of spi_setup_slave
Need to check value of spi_setup_slave and spi_setup_slave_fdt.
If their return value 'bus' is NULL, there is no need to pass it
to following spi_flash_probe_tail.

If 'bus' is null, the original function flow is as following:
spi_flash_probe
	|->spi_setup_slave
	|->spi_probe_bus_tail
		|->spi_flash_probe_slave
		|->spi_free_slave
Alougth check the pointer in spi_free_slave is ok, checking the return value
of spi_setup_slave and spi_setup_slave_fdt is better.

Before this fix:
"
=> sf probe 0:2
FSL_QSPI: Not a valid cs !
SF: Failed to set up slave
data abort
pc : [<fff66dcc>]          lr : [<fff7628c>]
reloc pc : [<87814dcc>]    lr : [<8782428c>]
sp : fdf4fcf0  ip : e630396c     fp : fe0d0888
r10: fffa2538  r9 : fdf4feb8     r8 : 02625a00
r7 : 00000002  r6 : fff94ec0     r5 : 00000000  r4 : 9355553c
r3 : 1af0593c  r2 : cb3fe030     r1 : fff94eb8  r0 : e59ff018
Flags: nZCv  IRQs off  FIQs off  Mode SVC_32
Resetting CPU ...
"

After this fix:
"
=> sf probe 0:2
FSL_QSPI: Not a valid cs !
Failed to initialize SPI flash at 0:2
"
No data abort using this patch.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2015-04-22 17:06:13 +05:30
Siva Durga Prasad Paladugu
06bc1756c5 sf: Poll both the read status and flag status
Poll both the Read status and Flag status registers
for sucessful erase and program operations for the
Micron devices with E_FSR flag set in params table.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2015-04-22 16:49:51 +05:30
Simon Glass
949dd81b43 sandbox: Move CONFIG_SPI_FLASH_SANDBOX to Kconfig
Move this over to Kconfig and tidy up.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:38 -06:00
Masahiro Yamada
b3d023b405 dm: spi_flash: fix wrong dependency
CONFIG_SPI does not exist in Kconfig in the first place, so the
dependency "depends on DM && SPI" is never met, i.e., DM_SPI_FLASH
can never be enabled (unless you ignore the dependency in an illegal
way.  See below.)

Actually, some defconfigs such as socfpga_*_defconfig define
CONFIG_DM_SPI_FLASH=y, but it never appears in the .config file
because of this wrong dependency.

On the other hand, all the Tegra boards enable DM_SPI_FLASH because

  config DM_SPI_FLASH
          default y

silently ignores the dependency.
Unfortunately, this style of CONFIG definition is abused everywhere
in U-Boot, so we easily miss such a wrong dependency.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:30 -06:00
Simon Glass
8d987abc6a dm: sf: Add driver model read/write/erase methods
Permit use of a udevice to talk to SPI flash. Ultimately we would like
to retire the use of 'struct spi_flash' for this purpose, so create the
new API for those who want to move to it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:14 -06:00
Joe Hershberger
0eb25b6196 common: Make sure arch-specific map_sysmem() is defined
In the case where the arch defines a custom map_sysmem(), make sure that
including just mapmem.h is sufficient to have these functions as they
are when the arch does not override it.

Also split the non-arch specific functions out of common.h

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:09 -06:00
Simon Glass
e564f054af dm: core: Add dev_get_uclass_priv() to access uclass private data
Add a convenience function to access the private data that a uclass stores
for each of its devices. Convert over most existing uses for consistency
and to provide an example for others.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-04-16 19:27:42 -06:00
Albert ARIBAUD \(3ADEV\)
c8381bf435 lpc32xx: mtd: nand: add MLC NAND controller
The controller's Reed-Solomon ECC hardware is
used except of course for raw reads and writes.
It covers in- and out-of-band data together.

The SPL framework is supported.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10 14:22:56 +02:00
Tom Rini
10697704ca Merge branch 'master' of git://git.denx.de/u-boot-atmel 2015-03-31 19:15:59 -04:00
David Dueck
da78fb5414 ARM: at91: atmel_nand: Support flash based BBT
Add support for on-flash bad block table. This makes U-Boot handle an existing
BBT correctly.

Signed-off-by: David Dueck <davidcdueck@googlemail.com>
Reviewed-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
CC: Boris BREZILLON <boris.brezillon@free-electrons.com>
CC: Josh Wu <josh.wu@atmel.com>
CC: Andreas Bießmann <andreas.devel@googlemail.com>
CC: Scott Wood <scottwood@freescale.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
2015-04-01 01:04:28 +02:00
Stefan Agner
55765b1842 mtd: vf610_nfc: specify transfer size before each transfer
Testing showed, that commands like STATUS made the buffer dirty
when executed with NFC_SECSZ set to the page size. It looks
like the controller transfers bogus data when this register
is configured. When setting it to 0, the buffer does not get
altered while the status command still seems to work flawless.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-03-30 23:35:27 -05:00
Stefan Agner
7653fc288a mtd: vf610_nfc: mark page as dirty on block erase
The driver tries to re-use the page buffer by storing the page
number of the current page in the buffer. The page is only read
if the requested page number is not currently in the buffer. When
a block is erased, the page number is marked as invalid if the
erased page equals the one currently in the cache. However, since
a erase block consists of multiple pages, also other page numbers
could be affected.

The commands to reproduce this issue (on a written page):
> nand dump 0x800
> nand erase 0x0 0x20000
> nand dump 0x800

The second nand dump command returns the data from the buffer,
while in fact the page is erased (0xff).

Avoid the hassle to calculate whether the page is affected or not,
but set the page buffer unconditionally to invalid instead.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2015-03-30 23:33:42 -05:00
Peter Tyser
004a1fdb45 nand: yaffs: Remove the "nand write.yaffs" command
This command is only enabled by one board, complicates the NAND code,
and doesn't appear to have been functioning properly for several
years.  If there are no bad blocks in the NAND region being written
nand_write_skip_bad() will take the shortcut of calling nand_write()
which bypasses the special yaffs handling.  This causes invalid YAFFS
data to be written. See
http://lists.denx.de/pipermail/u-boot/2011-September/102830.html for
an example and a potential workaround.

U-Boot still retains the ability to mount and access YAFFS partitions
via CONFIG_YAFFS2.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2015-03-30 23:24:39 -05:00
Peter Tyser
073adf987e nand: Remove CONFIG_MTD_NAND_VERIFY_WRITE
The CONFIG_MTD_NAND_VERIFY_WRITE has been removed from Linux for some
time and a more generic method of NAND verification now exists in U-Boot.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2015-03-30 23:24:39 -05:00
Peter Tyser
59b5a2ad83 nand: Add verification functions
Add nand_verify() and nand_verify_page_oob().  nand_verify() verifies
NAND contents against an arbitrarily sized buffer using ECC while
nand_verify_page_oob() verifies a NAND page's contents and OOB.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2015-03-30 23:24:38 -05:00
Luca Ellero
88a2cbb2ae mtd: nand: mxs: fix PIO_WORDs in mxs_nand_write_buf()
There is only one pio_word in this DMA transaction so data field must be 1.

Signed-off-by: Luca Ellero <luca.ellero@brickedbrain.com>
2015-03-30 22:25:54 -05:00
Luca Ellero
5263a02e8b mtd: nand: mxs: fix PIO_WORDs in mxs_nand_read_buf()
There is only one pio_word in this DMA transaction so data field must be 1.

Signed-off-by: Luca Ellero <luca.ellero@brickedbrain.com>
2015-03-30 22:25:47 -05:00
Ash Charles
b050898efa omap: gpmc: 'nandecc sw' can use HAM1 or BCH8
The 'nandecc sw' command selects a software-based error correction
algorithm.  By default, this is OMAP_ECC_HAM1_CODE_SW but some
platforms use OMAP_ECC_BCH8_CODE_HW_DETECTION_SW as their
software-based correction algorithm.  Allow a user to be specific e.g.
 # nandecc sw <hamming|bch8>
where 'hamming' is still the default.

Note: we don't just use CONFIG_NAND_OMAP_ECCSCHEME as it might be set
      to a hardware-based ECC scheme---a little strange when the user
      has requested 'sw' ECC.

Signed-off-by: Ash Charles <ashcharles@gmail.com>
2015-03-05 20:49:43 -05:00
Michal Sojka
d8af39337e mtd: nand: omap_gpmc: Make ready/busy pins configurable
Commit fb384c4720 introduced the use of
WAIT0 pin for determining whether the NAND is ready or not. This only
works if all NAND chips are connected to WAIT0. If some chips are
connected to the other available pin WAIT1, nand_wait() does not really
wait and prints a WARN_ON message.

This patch allows the board to provide configuration of which chip is
connected to which WAITx signal. For example, one can define in
include/configs/foo.h:

    #define CONFIG_NAND_OMAP_GPMC_WSCFG     0,0,1,1

This would mean that chips using to CS0 and 1 are connected to WAIT0 and
chips with CS2 and 3 are connected to WAIT1.

Signed-off-by: Michal Sojka <sojka@merica.cz>
Acked-by: Stefan Roese <sr@denx.de>
Tested-by: Michal Vokáč <michal.vokac@comap.cz>

Cc: Tom Rini <trini@ti.com>
2015-03-05 20:49:42 -05:00
Masahiro Yamada
d648964fc2 kconfig: remove unneeded dependency on !SPL_BUILD
Now CONFIG_SPL_BUILD is not defined in Kconfig, so
"!depends on SPL_BUILD" and "if !SPL_BUILD" are redundant.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-02-24 17:06:27 -05:00
Masahiro Yamada
e02ee2548a kconfig: switch to single .config configuration
When Kconfig for U-boot was examined, one of the biggest issues was
how to support multiple images (Normal, SPL, TPL).  There were
actually two options, "single .config" and "multiple .config".
After some discussions and thought experiments, I chose the latter,
i.e. to create ".config", "spl/.config", "tpl/.config" for Normal,
SPL, TPL, respectively.

It is true that the "multiple .config" strategy provided us the
maximum flexibility and helped to avoid duplicating CONFIGs among
Normal, SPL, TPL, but I have noticed some fatal problems:

[1] It is impossible to share CONFIG options across the images.
  If you change the configuration of Main image, you often have to
  adjust some SPL configurations correspondingly.  Currently, we
  cannot handle the dependencies between them.  It means one of the
  biggest advantages of Kconfig is lost.

[2] It is too painful to change both ".config" and "spl/.config".
  Sunxi guys started to work around this problem by creating a new
  configuration target.  Commit cbdd9a9737 (sunxi: kconfig: Add
  %_felconfig rule to enable FEL build of sunxi platforms.) added
  "make *_felconfig" to enable CONFIG_SPL_FEL on both images.
  Changing the configuration of multiple images in one command is a
  generic demand.  The current implementation cannot propose any
  good solution about this.

[3] Kconfig files are getting ugly and difficult to understand.
  Commit b724bd7d63 (dm: Kconfig: Move CONFIG_SYS_MALLOC_F_LEN to
  Kconfig) has sprinkled "if !SPL_BUILD" over the Kconfig files.

[4] The build system got more complicated than it should be.
  To adjust Linux-originated Kconfig to U-Boot, the helper script
  "scripts/multiconfig.sh" was introduced.  Writing a complicated
  text processor is a shell script sometimes caused problems.

Now I believe the "single .config" will serve us better.  With it,
all the problems above would go away.  Instead, we will have to add
some CONFIG_SPL_* (and CONFIG_TPL_*) options such as CONFIG_SPL_DM,
but we will not have much.  Anyway, this is what we do now in
scripts/Makefile.spl.

I admit my mistake with my apology and this commit switches to the
single .config configuration.

It is not so difficult to do that:

 - Remove unnecessary processings from scripts/multiconfig.sh
  This file will remain for a while to support the current defconfig
  format.  It will be removed after more cleanups are done.

 - Adjust some makefiles and Kconfigs

 - Add some entries to include/config_uncmd_spl.h and the new file
   scripts/Makefile.uncmd_spl.  Some CONFIG options that are not
   supported on SPL must be disabled because one .config is shared
   between SPL and U-Boot proper going forward.  I know this is not
   a beautiful solution and I think we can do better, but let's see
   how much we will have to describe them.

 - update doc/README.kconfig

More cleaning up patches will follow this.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-02-24 17:06:23 -05:00
Egli, Samuel
89831112d4 mtd, omap: fix case NAND_OMAP_GPMC_PREFETCH not defined
The patch c316f577b4 breaks
siemens boards because prefetch mode is not enabled.
I assume it breaks other boards as well that don't use
prefetch.

This patch sets read_buf to nand_read_buf if
NAND_OMAP_GPMC_PREFETCH is not defined.

Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
CC: Daniel Mack <zonque@gmail.com>
CC: Guido Martínez <guido@vanguardiasur.com.ar>
CC: Tom Rini <trini@ti.com>
CC: Heiko Schocher <hs@denx.de>
2015-02-16 12:41:40 -05:00
Simon Glass
f94a1bed07 dm: Expand and complete Kconfig in drivers/
Expand the help messages for each driver. Add missing Kconfig for I2C,
SPI flash and thermal.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-02-12 10:35:33 -07:00
Wu, Josh
0e48dc5e41 mtd: atmel_nand: according to pmecc version to perform 0xff page correction
As the PMECC hardware has different version. In SAMA5D4 chip, the PMECC ip
can generate 0xff pmecc ECC value for all 0xff sector.

According to this, add PMECC version check, if it's SAMA5D4 then we always
let PMECC hardware to correct it.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-02-07 23:42:57 +01:00
Tom Rini
7f641d53bb Merge branch 'master' of git://git.denx.de/u-boot-ubi 2015-02-04 13:30:00 -05:00
Simon Glass
d0cff03e18 dm: spi: Move slave details to child platdata
At present we go through various contortions to store the SPI slave's chip
select in its private data. This only exists when the slave is active so
must be set up when it is probed. Until the device is probed we don't
actually know what chip select it will appear on.

However, now that we can support per-child platform data, we can use that
instead. This allows us to set up the chip select when the child is bound,
and avoid the messy contortions.

Unfortunately this is a fairly large change and it seems to be difficult to
break it down further.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-29 17:09:56 -07:00
Simon Glass
1603bf3cc1 dm: sandbox: sf: Tidy up the error handling in sandbox_sf_probe()
Use a single exit point when we have an error and add debugging there.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-29 17:09:56 -07:00
Simon Glass
b0265d56fe dm: tegra: nand: Remove use of fdtdec GPIO support
These functions are going away, so use the new uclass support instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-29 17:09:52 -07:00