For configurations with gmii2rgmii and external phy the DT nodes link
should be gem->gmii2rgmii->phy. But due to limitation in Linux driver
the DT is mentioned as gem->phy and gmii2rgmii->phy as shown in below DT.
ethernet@ff0c0000 {
compatible = "cdns,zynqmp-gem\0cdns,gem";
status = "okay";
interrupt-parent = <0x04>;
interrupts = <0x00 0x3b 0x04 0x00 0x3b 0x04>;
reg = <0x00 0xff0c0000 0x00 0x1000>;
clock-names = "pclk\0hclk\0tx_clk\0rx_clk\0tsu_clk";
#address-cells = <0x01>;
#size-cells = <0x00>;
#stream-id-cells = <0x01>;
iommus = <0x0d 0x875>;
power-domains = <0x0c 0x1e>;
clocks = <0x03 0x1f 0x03 0x69 0x03 0x2e 0x03 0x32 0x03 0x2c>;
phy-handle = <0x0e>;
phy-mode = "gmii";
xlnx,ptp-enet-clock = <0x00>;
local-mac-address = [ff ff ff ff ff ff];
phandle = <0x4d>;
mdio {
#address-cells = <0x01>;
#size-cells = <0x00>;
phandle = <0x4e>;
ethernet-phy@1 {
reg = <0x01>;
rxc-skew-ps = <0x708>;
txc-skew-ps = <0x708>;
phandle = <0x0e>;
};
gmii_to_rgmii_0@8 {
compatible = "xlnx,gmii-to-rgmii-1.0";
phy-handle = <0x0e>;
reg = <0x08>;
phandle = <0x4f>;
};
};
};
Since same DT is used in Linux and U-Boot we need to workaround this
issue by using the gmii2rgmii node which points to phy and we should
ignore the gem pointing to phy directly.
Do this workaround by updating priv->phydev->node value with
priv->phy_of_node only if it is not valid node.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Link: https://lore.kernel.org/r/641eb13425ffe80e0743f60cf90d0f940577b9e9.1642162085.git.michal.simek@xilinx.com
Add PSGTR driver for Xilinx ZynqMP.
The most of configurations are taken from Linux kernel psgtr driver.
USB3.0 and SGMII configurations are tested on SOM. In SGMII case also
IOU_SLCR reg is updated to get proper clock setup and signal detection
configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/36e6e9d3baf8511af1916e91e4887032ca2b6c20.1641458978.git.michal.simek@xilinx.com
When a MAC address is randomly generated we currently only update the
appropriate data structure. For consistency and to re-align with
historic usage, it should be also saved to the appropriate environment
variable as well.
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[trini: Update Kconfig, handle legacy networking case as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
Link: https://lore.kernel.org/r/1a2518e3cc19c14a41875ef64c5acc1f16edc813.1641893287.git.michal.simek@xilinx.com
Perform reset before core initialization.
Standard flow which close to 99% users are using getting all IPs out of
reset that there is no need to reset IP again. This is because of all low
level initialization is done in previous bootloader stage.
In SOM case these IPs are not touched by previous bootloader stage that's
why reset needs to be called before IP is accessed to make sure that it is
in correct state.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Link: https://lore.kernel.org/r/5ae1c85b282d632bb62030f1f24a0065661b9153.1638804318.git.michal.simek@xilinx.com
Xilinx DTS files are using two way how to describe ethernet phy.
The first (already supported) has phy as subnode of gem node.
eth {
phy-handle = <&phy0>;
phy0: ethernet-phy@21 {
...
};
};
The second has mdio subnode (with mdio name) which has phy subnode. This
structure allow hadling MDIO reset signal (based on Linux mdio.yaml)
eth {
phy-handle = <&phy0>;
mdio {
phy0: ethernet-phy@21 {
...
};
};
};
This patch adds support for the second case where mdio subnode
is found driver will look at its parent to find out which gem is handling
MDIO bus.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/6748007f0b6db9554d7a4b52352dce23ca403f9d.1638798796.git.michal.simek@xilinx.com
The system fails to boot without any environment location, so return
ENVL_NOWHERE when there's nowhere to store the environment instead
of ENVL_UNKNOWN.
The same change was also done by commit 50918d0df5 ("xilinx: Return
ENVL_NOWHERE instead of ENVL_UNKNOWN") for zynq and zynqmp.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/e4ed36408f10159677ed8060bfd5289f3e0691fa.1637752614.git.michal.simek@xilinx.com
The xilinx board_fdt_blob_setup() implementation makes use of
XILINX_OF_BOARD_DTB_ADDR, but no default value is currently defined for
microblaze. Add one so that microblaze could also work with
CONFIG_OF_SEPARATE.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211202195657.246723-1-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current code assumes that the vector base address is always at 0x0.
However, this value is configurable for MicroBlaze using the
CONFIG_XILINX_MICROBLAZE0_VECTOR_BASE_ADDR Kconfig option. Update the
reset routines to branch to this location instead.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-10-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current code assumes that the vector base address is always at 0x0.
However, this value is configurable for MicroBlaze, so update the
__setup_exceptions routine to work with any vector base address.
The r4 register is reserved for the vector base address inside
__setup_exceptions and the function prologe/epilogue are also updated to
save and restore r4.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-9-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
MicroBlaze vector base address is configurable (hdl C_BASE_VECTORS
configuration parameter). Current code assumes that the reset vector
location is always 0x0.
Add the XILINX_MICROBLAZE0_VECTOR_BASE_ADDR Kconfig option so the user
can adjust the reset vector address.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-8-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Migrate CONFIG_SYS_USR_EXCEP to Kconfig. Also, rename it to
XILINX_MICROBLAZE0_USR_EXCEP in order to match the naming convention of
microblaze-generic Kconfig options.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-7-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Microblaze is one the last two users of the CONFIG_SYS_RESET_ADDRESS
macro (the other is arch/powerpc/cpu/mpc8xx/cpu.c, but the macro is not
defined anywhere in powerpc code, so it should be removed there too).
Replace CONFIG_SYS_RESET_ADDRESS usage in start.S with
CONFIG_SYS_TEXT_BASE. If the reset address should really be
user-configurable, a new Kconfig option could be added.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-6-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
To simpify the code, use stack space as scratch memory for endian offset
calculation, rather than saving/restoring the first unused MB vector.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-5-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable SPL_LIBCOMMON_SUPPORT and SPL_LIBGENERIC_SUPPORT if CONFIG_SPL=y, in
order to fix the following link failures:
common/spl/spl.o: in function `board_init_r':
common/spl/spl.c:755: undefined reference to `puts'
...
common/spl/spl.o: in function `board_init_r':
common/spl/spl.c:756: undefined reference to `hang'
common/spl/spl.c:740: undefined reference to `memset'
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-4-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Microblaze has three boot modes defined in microblaze/include/asm/spl.h,
but only booting from NOR flash is currently useable. Add a custom
board_boot_order() implementation so that RAM and SPI boot modes can also
be selected if the corresponding load-image support is present.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-3-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
board_fdt_blob_setup() uses the _end symbol to find the dtb in the non-spl
case. In order to allow microblaze builds to compile successfully with
CONFIG_OF_SEPARATE, the _end symbol must be defined. Align microblaze with
the other architectures and use _end symbol rather than __end to mark the
end of the u-boot binary.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/20211130163358.2531677-2-ovidiu.panait@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Previous psu init was targeting SOM + KV260 carrier card and also contain
configurations for other devices on carrier card. This config is removing
all expected configurations for CC and let U-Boot to handle all of it self.
This configuration is designed for SOM itself (and I would bet without
eMMC).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/5782131058dc372befd3fdb4dceabeea5ba56606.1637236693.git.michal.simek@xilinx.com
ZynqMP modepin driver has capability to get/set/check status of modepin
gpios. These modepins are accessed using xilinx firmware. In modepin
register, [3:0] bits set direction, [7:4] bits read IO, [11:8] bits
set/clear IO.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/2d802d98fd56d95d764532a33e844d935e0cebb3.1635505900.git.michal.simek@xilinx.com
The common emulation Makefile has a dependency on a non-existent
qemu_capsule.o when building with support for capsule update enabled
(CONFIG_EFI_RUNTIME_UPDATE_CAPSULE=y).
The code which was in qemu_capsule.c has been completely moved to
lib/efi_loader/efi_capsule.c by commit 7a6fb28c8e ("efi_loader: capsule:
add back efi_get_public_key_data()").
Remove the false dependency.
This fixes the following build error:
make[1]: *** No rule to make target 'board/emulation/common/qemu_capsule.o', needed by 'board/emulation/common/built-in.o'. Stop.
Fixes: commit 47a25e81d3 ("Revert "efi_capsule: Move signature from DTB to .rodata"")
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Simon Glass <sjg@chromium.org>
Add an entry in maintainers for fastboot. It is starting off orphaned, but
hopefully someone can pick it up.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Lukasz has not been very responsive in reviewing clock patches. Add
myself as a maintainer.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Test:
* fix pylint warnings
UEFI:
* disable interrupts before removing devices in ExitBootServices()
* implement poweroff in efi_system_reset() on sandbox
* allow booting via EFI even if some block device fails
-----BEGIN PGP SIGNATURE-----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=X5Tv
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-01-rc3-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-01-rc3-2
Test:
* fix pylint warnings
UEFI:
* disable interrupts before removing devices in ExitBootServices()
* implement poweroff in efi_system_reset() on sandbox
* allow booting via EFI even if some block device fails
* there is no os.path.unlink() method
* don't inherit from object
* add module docstring
* move imports to the top
* avoid unused variable
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
* don't inherit from object
* imports should be on the top level
* avoid unused variable names
* avoid unnecessary else after raise
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
UEFI code is always little-endian. Remove a superfluous test.
Remove a superfluous type conversion.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
If we call efi_clear_os_indications() before initializing the memory store
for UEFI variables a NULL pointer dereference occurs.
The error was observed on the sandbox with:
usb start
host bind 0 sandbox.img
load host 0:1 $kernel_addr_r helloworld.efi
bootefi $kernel_addr_r
Here efi_resister_disk() failed due to an error in the BTRFS implementation.
Move the logic to clear EFI_OS_INDICATIONS_FILE_CAPSULE_DELIVERY_SUPPORTED
to the rest of the capsule code.
If CONFIG_EFI_IGNORE_OSINDICATIONS=y, we should still clear the flag.
If OsIndications does not exist, we should not create it as it is owned by
the operating system.
Fixes: 149108a3eb ("efi_loader: clear OsIndications")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
efi_system_reset() should exit if called with EFI_RESET_SHUTDOWN.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Our algorithm for creating USB device paths may lead to duplicate device
paths which result in efi_disk_register() failing. Instead we should just
skip devices that cannot be registered as EFI block devices.
Fix a memory leak in efi_disk_add_dev() caused by the duplicate device
path.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
If we look at the path that bootm/booti take when preparing to boot the
OS, we see that as part of (or prior to calling do_bootm_states,
explicitly) the process, bootm_disable_interrupts() is called prior to
announce_and_cleanup() which is where udc_disconnect() /
board_quiesce_devices() / dm_remove_devices_flags() are called from. In
the EFI path, these are called afterwards. In efi_exit_boot_services()
however we have been calling bootm_disable_interrupts() after the above
functions, as part of ensuring that we disable interrupts as required
by the spec. However, bootm_disable_interrupts() is also where we go
and call usb_stop(). While this has been fine before, on the TI J721E
platform this leads us to an exception. This exception seems likely to
be the case that we're trying to stop devices that we have already
disabled clocks for. The most direct way to handle this particular
problem is to make EFI behave like the do_bootm_states() process and
ensure we call bootm_disable_interrupts() prior to ending up in
usb_stop().
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Simon Glass <sjg@chromium.org>
Suggested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Scripts:
* Update spelling.txt
LMB:
* remove extern keyword in lmb.h
* drop unused lmb_size_bytes()
Test:
* test truncation in snprintf()
Documentation:
* add include/lmb.h to HTML documentation
UEFI:
* reduce non-debug logging output for measured boot
* fix use after free in measured boot
* startup the tpm device when installing the protocol
* implement EFI_EVENT_GROUP_BEFORE_EXIT_BOOT_SERVICES
* record capsule result only if capsule is read
Due to U-Boot's lazy binding mentality the TPM is probed but not properly
initialized. The user can startup the device from the command line
e.g 'tpm2 startup TPM2_SU_CLEAR'. However we can initialize the TPM during
the TCG protocol installation, which is easier to use overall.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
As described in the TCG spec [1] in sections 7.1.1 and 7.1.2 the FinalEvent
table should include events after GetEventLog has been called. This
currently works for us as long as the kernel is the only EFI application
calling that. Specifically we only implement what's described in 7.1.1.
So refactor the code a bit and support EFI application(s) calling
GetEventLog. Events will now be logged in both the EventLog and FinalEvent
table as long as ExitBootServices haven't been invoked.
[1] https://trustedcomputinggroup.org/wp-content/uploads/EFI-Protocol-Specification-rev13-160330final.pdf
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
