This adds platform code and the device tree for the Phytium Pomelo Board.
The initial support comprises the UART and the PCIE.
Signed-off-by: weichangzheng <nicholas_zheng@outlook.com>
QSGMII PHY present on the j721e common processor board requires
to be initialized before the core boots up. Therefore, run the
corresponding command during boot to do the same.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add the command "boot_rprocs" that is required for booting remote
processors in U-Boot.
Fixes: 5980925e2a ("include: configs: j721e_evm: Add support to boot ethfw core in j721e")
Reported-by: Jesse Villarreal <jesse.villarreal@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Enabling DM_PMIC, DM_REGULATOR_FIXED, and DM_REGULATOR_GPIO
gives us the ability to better monitor voltages and enable
hardware through the device tree. The TL4030 (TPS65950) is
not yet migrated to DM, so this patch only enables the fixed
and GPIO controlled regulators.
Based on commit [1][2].
[1] a40d3cc845
[2] 2448e42d73
Signed-off-by: Romain Naour <romain.naour@gmail.com>
The simple pinctrl driver currently available works with the omap3.
Enabling this will use the device tree to automatically set the
pin-muxing for various drivers.
Based on commit: 57dbf754e3
Signed-off-by: Romain Naour <romain.naour@gmail.com>
This hook can be implmented using events, for the three boards that
actually use it.
Add the event type and event handlers. Drop CONFIG_MISC_INIT_F since we
can just use CONFIG_EVENT to control this. Since sandbox always enables
CONFIG_EVENT, we can drop the defconfig lines there too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some sunxi boards ship with SPI flash, which allows booting through the
BootROM. We cover this functionality by a separate SPL "mini" driver.
Separately we have a proper DM_SPI driver for U-Boot proper, which
provides access to the SPI flash through the "sf" command. That allows
to update the firmware on the SPI flash, also to store the environment
there.
However only very few boards actually enable support for U-Boot proper,
even though that would work and the SPL part is configured.
Use the cleaned up configuration scheme to enable SPI flash on those
boards which mention a SPI flash in their .dts, or which use the SPL SPI
support.
Out of the box this would enable storing the environment on the SPI
flash, and allows people to read or write the flash from U-Boot, for
instance to update the SPI flash when booted via an SD card.
For this to actually work there must be a "spi0" alias in the DT, which
most boards are missing. But this should be addressed separately.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Commit 7945caf22c ("arm: sunxi: Enable SPI/SPI-FLASH support for A64")
selected CONFIG_SPI by default on all Allwinner A64 boards, even though
only 4 out of the 14 A64 boards have a SPI flash chip. All other SoCs
had to manually select DM_SPI and friends, even though they are a
platform property (the sunxi SPI driver is DM_SPI only).
Clean this up to allow easy selection of SPI flash support in U-Boot
proper, by selecting DM_SPI and DM_SPI_FLASH *if* CONFIG_SPI is
selected, for *all* Allwinner SoCs. This simplifies the defconfig for
two Libretech boards already.
Also remove the forced CONFIG_SPI from the A64 Kconfig, instead let the
four boards which allow SPI booting select this explicitly.
Any board wishing to support SPI flash in U-Boot proper now just defines
CONFIG_SPI and CONFIG_SPI_FLASH_<vendor> in its defconfig, Kconfig takes
care of the rest.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Mechanically convert video_hw_init() function to UCLASS_VIDEO probe
callback and replace CONFIG_CFB_CONSOLE by CONFIG_DM_VIDEO.
As framebuffer base address is setup by the bootloader which loads U-Boot,
set plat->base to that fixed framebuffer address.
This change was tested in qemu n900 machine and is working fine.
What does not work is CONFIG_VIDEO_LOGO, seems to be buggy.
Signed-off-by: Pali Rohár <pali@kernel.org>
This add the initial support of the broadcom reference
board bcm96753ref with a bcm6753 SoC.
This board has 1 GB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Enable ext4 write support in Turris Omnia's defconfig. Some users find
it useful.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_CHIP_SELECTS_PER_CTRL
Cc: Alison Wang <alison.wang@nxp.com>
Cc: Pramod Kumar <pramod.kumar_1@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOOTP_MAY_FAIL
CONFIG_BOOTP_VENDOREX
CONFIG_BOOTP_BOOTFILESIZE
CONFIG_BOOTP_NISDOMAIN
CONFIG_BOOTP_TIMEOFFSET
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The F1C100s DT contains the wrong compatible string for the watchdog,
which breaks reset functionality.
Updating the DT goes via the Linux tree, but to allow reset
functionality meanwhile (useful for development!), disable SYSRESET for
now, to let the old-fashioned watchdog driver kick in and provide the
reset_cpu() implementation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Enable SPI boot in SPL on SUNIV architecture and use
it in the licheepi nano that uses the F1C100s.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch scans the cmdline from the Samsung SBL (second stage
bootloader) and stores the parameters board_id=N and lcdtype=N
in order to augment the DTB for different board and LCD types.
We then add a custom ft_board_setup() callback that will inspect
the DTB and patch it using the stored LCD type. At this point
we know which product we are dealing with, so using the passed
board_id we can also print the board variant for diagnostics.
We patch the Codina, Skomer and Kyle DTBs to use the right
LCD type as passed in lcdtype from the SBL.
This also creates an infrastructure for handling any other
Samsung U8500 board variants that may need a slightly augmented
DTB.
Cc: Markuss Broks <markuss.broks@gmail.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Support for Apple M1 Pro and Max will allow using a single binary for
all M1 SoCs. The M1 Pro/Max have a different memory layout. The RAM
start address is 0x100_0000_0000 instead of 0x8_0000_0000.
Replace the hardcoded memory layout with dynamic initialized
environment variables in board_late_init().
Tested on Mac Mini (2020) and Macbook Pro 14-inch (2021).
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Simplify the binman config and fdt nodes by using the "@..-SEQ"
substitutions and CONFIG_OF_LIST.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Nowadays, u-boot (when CONFIG_NET_RANDOM_ETHADDR is set) will set
enetaddr to a random value if not set and then pass the randomly
generated MAC address to linux.
This is bad for the following reasons:
(1) it makes it impossible for linux to detect this error
(2) linux won't trigger any fallback mechanism for the case where
it didn't find any valid MAC address
(3) a saveenv will store this randomly generated MAC address in the
environment
Probably, the user will also be unaware that something is wrong. He will
just get different MAC addresses on each reboot, asking himself why this
is the case.
As this board usually have a serial port, the user can just fix this by
setting the MAC address manually in the environment. Also disable the
netconsole just in case, because it cannot be guaranteed that it will
work in any case. After all, this was just a convenience option, because
the bootloader - right now - doesn't have the ability to read the MAC
address, which is stored in the OTP. But it is far more important to
have a clear view of whats wrong with a board and that means we can no
longer use this Kconfig option.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The SoC provides two additional watchdogs integrated in the SoC. Enable
support for these.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable the GPIO and watchdog driver. Don't start the watchdog
automatically, though.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The wrong phy was being enabled, because it worked and the proper
PHY did not. After the Renesas maintainer made some adjustments
to the device tree, Linux was able to use the proper driver, and
when that device tree was ported to Linux, the ethernet stopped
working due to the lack of rgmii-rxid support. Now that
rgmii-rxid is supported, enable the proper driver to restore
ethernet function.
Fixes: 1eaf61c84d ("arm: dts: beacon-rzg2: Resync device trees with Linux 5.16-rc3")
Signed-off-by: Adam Ford <aford173@gmail.com>
With the Kconfig options being deleted, the references to
OMAP_EHCI_PHY are useless. Remove them from the various
defconfigs.
Signed-off-by: Adam Ford <aford173@gmail.com>
The address of the debug UART varies differs between the M1 and
the M1 Pro/Max SoCs. So we have to disable it to make a single
U-Boot binary that works on all SoC generations. Leave the
settings for the base address and clock rate of the M1 in place
to make it easier to re-enable the debug UART when needed.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
ZYNQMP_PSU_INIT_ENABLED is called only when BOARD_EARLY_INIT_F is defined
that's why cover this dependency in Kconfig.
board_early_init_f() is only part related to
CONFIG_ZYNQMP_PSU_INIT_ENABLED which is disabled now that's why disable
BOARD_EARLY_INIT_F and also build board_early_init_f() only when
CONFIG_BOARD_EARLY_INIT_F is enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/d89253ec1590cd513dcd4bfbedebae618bd6d605.1645104518.git.michal.simek@xilinx.com
ZYNQMP_PSU_INIT_ENABLED specifically saying that has connection to full
U-Boot not SPL that's why build psu_spl_init for SPL all the time.
Also disable ZYNQMP_PSU_INIT_ENABLED because it ends up in situation that
psu_init() is called twice which is wrong. By default only SPL should call
it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/bf1e5d9a163f8853c7d951ad42965114ab0b1f50.1645104518.git.michal.simek@xilinx.com
The commit 9855034397 ("fdt: Don't call board_fdt_blob_setup() without
OF_BOARD") forced to enable OF_BOARD for platforms which provide DT
externally. Zynq/ZynqMP boards are using this feature for a long time
that's why there is a need to enable it by default.
Also code expects to return error in case of error that's why also fill it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/9f11bbffe2849f4da7d72712082d579262fe8fd8.1645104518.git.michal.simek@xilinx.com
Add support for ethernet on the imx8mn-ddr4-evk.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enought space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
After this change it would be possible to use 'mtd' command to get access
to XEA's SPI-NOR partitions by name (e.g. SPL), not by offsets.
To enable this feature the CONFIG_SPI_FLASH_MTD needs to be defined in the
Kconfig, not in xea.h.
=> mtd list
=> mtd read spl-boot-data1 ${loadaddr} 0x0 4
=> md.l ${loadaddr} 1
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Enable missing config options to make the board boot from SD card.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
To add support for the i.MX8M Nano GW7902:
- Add imx8mn-venice dts/defconfig/include
- Add imx8mn-gw7902 dts
- Add imx8mn-2gb lpddr4 dram configs
- Add misc support for IMX8M Nano SoC
- rename imx8mm-venice.c to venice.c as it is no longer imx8mm specific
- update README with differences for IMX8MN vs IMX8MM
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Make O4-iMX6ULL-NANO-based board compatible with Yocto layer meta-out4 and
fix device flashing by UUU (aka MFG Tools).
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
- a37xx: pci: Cleanup and minor fix for root port check (Pali)
- pci: mvebu: Ensure that root port is always on root zero bus (Pali)
- kwbimage: Fix dumping DATA registers for v0 images (Pali)
- kwbimage: Support for parsing extended v0 format (Pali)
- a37xx: Fix code and update DTS files to upstream version (Pali)
- a37xx: Fix and extend building memory map (Pali)
- ddr: marvell: a38x: fix BYTE_HOMOGENEOUS_SPLIT_OUT decision (Marek)
- mvebu: Optionally reset board on DDR training failure (Marek)
The state of the current DDR training code for Armada 38x is such that
we cannot be sure it will always train successfully - although after the
last change we were yet unable to find a board that failed DDR training,
from experience in the last 2 years we know that it is possible.
The experience also tells us that in many cases the board fails training
only sometimes, and after a reset the training is successful.
Enable the new option that makes the board reset itself on DDR training
failure immediately. Until now we called hang() in such a case, which
meant that the board was reset by the MCU after 120 seconds.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
S28HS512T on TI SK has sector size of 256KB, so update OSPI partition
to align on 256KB sector size. Since the sector size for MT35XU512ABA
on EVM is 128KB, partitions will remain aligned for EVM.
Also, now since the sector size is 256KB ospi.env.backup will collide
with ospi.sysfw, so move ospi.env.backup to the padding space (0x7C0000)
before ospi.rootfs partition.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Enable configs for building multiple dtbs into a single fit image
and load the right dtb for next stage. This will help to use same
defconfig for both J721E EVM and SK boards.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
The changes introduced with commit 6337d53fdf ("arm: dts: sync am33xx
with Linux 5.9-rc7") prevent the PDU001 from operating correctly.
This patch fixes the configuration of the pin multiplexer and uart3.
Signed-off-by: Felix Brack <fb@ltec.ch>
Add CONFIG_TOOLS_MKEFICAPSULE. Then we want to always build mkeficapsule
if tools-only_defconfig is used.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver adds support for the keyboard on Apple Silicon laptops.
The controller for this keyboard sits on an SPI bus and uses an
Apple-specific HID over SPI protocol. The packets sent by this
controller for key presses and key releases are fairly simple and
are decoded directly by the code in this driver and converted into
standard Linux keycodes. The same controller handles the touchpad
found on these laptops. Packets for touchpad events are simply
ignored.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Add a driver for the NVMe storage controller integrated on
Apple SoCs. This NVMe controller isn't PCI based and deviates
from the NVMe standard in its implementation of the command
submission queue and the integration of an NVMMU that needs
to be managed. This commit tweaks the core NVMe code to
support the linear command submission queue implemented by
this controller. But setting up the submission queue and
managing the NVMMU controller is handled by implementing
the driver ops that were added in an earlier commit.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Tested-on: firefly-rk3399
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Apple SoCs have an integrated NVMe controller that isn't connected
over a PCIe bus. In preparation for adding support for this NVMe
controller, split out the PCI support into its own file. This file
is selected through a new CONFIG_NVME_PCI Kconfig option, so do
a wholesale replacement of CONFIG_NVME with CONFIG_NVME_PCI.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
The Pogoplug E02 board has the network chip Marvell 88E1116R. Convert
to Driver Model and use uclass mvgbe and the compatible driver M88E1118R
to bring up Ethernet.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- As the result of the migration to Driver Model, this u-boot image has
grown substantially (about 100K, give or take). The old envs location
at 0x60000 (384k) is no longer possible. Move it to 0xC0000 (768K).
- Miscellaneous changes: Move constants to .c file and remove header file
board/cloudengines/pogo_e02/pogo_e02.h, use CONFIG_SYS_THUMB_BUILD to
keep u-boot image under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Dockstar board has the network chip Marvell 88E1116R. Convert to
Ethernet driver model, and use uclass mvgbe and the compatible driver
M88E1118R to bring up Ethernet.
- Add CONFIG_DM_ETH and associated configs.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Add CONFIG_PHY_MARVELL to properly configure the network.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Miscellaneous changes: Move constants to .c file and remove
header file board/Seagate/dockstar/dockstar.h, use
CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, add CONFIG_HUSH_PARSER, use BIT macro, and cleanup comments.
- Note: This patch is a RESEND for a previous patch:
https://patchwork.ozlabs.org/project/uboot/patch/20210812051854.1340-2-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Miscellaneous changes: Move constants to .c file and remove header file
board/iomega/iconnect/iconnect.h. Add CONFIG_HUSH_PARSER, use BIT macro,
and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Globalscale Technologies Dreamplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up both network
port 0 and 1. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add myself as maintainer (this board seems to be orphaned,
could not contact Jason Cooper using current email).
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/dreamplug/dreamplug.h, cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
This converts the following to Kconfig:
CONFIG_SCSI_AHCI_PLAT
CONFIG_SYS_SCSI_MAX_SCSI_ID
CONFIG_SYS_SCSI_MAX_LUN
CONFIG_SYS_SATA_MAX_DEVICE
Drop CONFIG_SCSI for everything except the sandbox build. We only need
one build for tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Move the SATA options inside an 'if SATA' part, so they are grouped.
Fix the 'Complient' typo while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_IDE_MAXBUS
CONFIG_SYS_IDE_MAXDEVICE
CONFIG_SYS_ATA_BASE_ADDR
CONFIG_SYS_ATA_STRIDE
CONFIG_SYS_ATA_DATA_OFFSET
CONFIG_SYS_ATA_REG_OFFSET
CONFIG_SYS_ATA_ALT_OFFSET
CONFIG_SYS_ATA_IDE0_OFFSET
CONFIG_SYS_ATA_IDE1_OFFSET
CONFIG_ATAPI
CONFIG_IDE_RESET
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Move setting the default boot command to the
apalis/colibri_imx6_defconfig. It allows replacing the command
without code modification.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The size of the board file is limited to 520192 bytes. This conflicts with
the size requirement for the UEFI code.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This option is selected implicitly when [SPL_]CLK_IMXRT10{20|50} is selected.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
The i.MX8M Nano can boot over USB using the boot ROM instead of
adding extra code to SPL to support USB drivers, etc. However,
when booting from USB, the environment doesnt' know where to load
and causes a hang. Fix this hang by supporting CONFIG_ENV_IS_NOWHERE=y.
It only falls back to this condition when booting from USB, so it
does not impact MMC booting.
Suggested-by: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
With the updated device tree's having USB support, enable in
U-Boot. This also requires the addition of the imx8m power
domain, since the USB is gated by the power domain controller.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The new configs/imx28_xea_sb_defconfig is introduced to facilitate
building the single binary u-boot.sb fox XEA board.
The biggest distinction from "normal" XEA imx28_xea_sb_defconfig is
support for USB mass storage devices (pen drives).
To achieve that, the CONFIG_DM_USB is enabled and supported.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The FXL6408 GPIO expander manages critical devices,
including on-module USB hub. Configure the expander to
switch the USB hub into bypass mode, allowing to use
on-carrier-board USB hub.
Signed-off-by: Oleksandr Suvorov <cryosay@gmail.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Previously these two options are called CONFIG_SPL_MMC_SUPPORT
and CONFIG_SPL_SERIAL_SUPPORT. During the transition they are
removed by accident. Thus adding them back.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The Lichee Pi Nano is a board based on the F1C100s.
Add defconfigs for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The initial patch had typos that caused four defconfigs to miss the
symbol transition to Kconfig. CONFIG_SYS_QE_FW_ADDR and
CONFIG_SYS_FMAN_FW_ADDR are currently initialized to 0 by default
on these builds, which prevents the firmware from loading.
Add the correct symbols to these defconfigs.
Fixes: a97a071d10 ("configs: fsl: migrate FMAN/QE specific defines to Kconfig")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Make it in a same way as on the other FOXMC products, this also helps to
avoid unwanted stop caused by some terminal servers that are sending junk
on the serial line.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds default defconfig for u-boot update version, the u-boot
update defconfig is a copy of the default (factory) defconfig with:
- adapted text base and environment addresses
- explicit flag that this is a field updated u-boot version
At the time of implementation this version is only used to verify the
update procedure, in future depend on the needs this defconfig can be
extended with additional options.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Field fail-safe u-boot update for pg-wcom-ls102x designs is introduced
with patch: 81fb05e.
This patch enables already added support by:
- Defining default u-boot build as bootpackage (factory) image.
- Defining u-boot update image location according to the EXPU1 NOR layout.
- Extending mtd partitions according defined EXPU1 NOR layout.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This is used by out ESW for reading u-boot build version.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This is used by out ESW for reading u-boot build version.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds default defconfig for u-boot update version, the u-boot
update defconfig is a copy of the default (factory) defconfig with:
- adapted text base and environment addresses
- explicit flag that this is a field updated u-boot version
At the time of implementation this version is only used to verify the
update procedure, in future depend on the needs this defconfig can be
extended with additional options.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Field fail-safe u-boot update for pg-wcom-ls102x designs is introduced
with patch 81fb05e.
This patch enables already added support by:
- Defining default u-boot build as bootpackage (factory) image.
- Defining u-boot update image location according to the SELI8 NOR layout.
- Extending mtd partitions according defined SELI8 NOR layout.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Ten64 is a networking-oriented MiniITX board
using the NXP LS1088A SoC.
This patch provides the bare minimum to support
Ten64 boards under U-Boot for distroboot.
Some related drivers have not yet been submitted
and this basic support lacks some of the
opinionated defaults provided by our firmware
distribution.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The GoFlex Home board has the network chip Marvell 88E1116R.
Use uclass mvgbe and the compatible driver M88E1118R to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: use CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add to support rsa 3072 bits algorithm in tools
for image sign at host side and adds rsa 3072 bits
verification in the image binary.
Add test case in vboot for sha384 with rsa3072 algorithm testing.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is enabled for quite a few boards which don't create ACPI tables.
Tidy this up by dropping the option for some boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
These have sadly found their way to ARM now. Allow any arch to support
generating ACPI tables.
Disable this for the tools build.
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit 270f8710f9 ("crc32: Add crc32 implementation using
__builtin_aarch64_crc32b") enabled the usage of ARMv8 CRC instructions
by default, for all arm64 builds. And indeed all Arm Ltd. v8 Cortex-A
cores support the instructions, and they are mandatory starting with
architecture revision v8.1, so realistically every known hardware
implementation should support them.
The Arm Fastmodel however defaults to the bare minimum ARMv8 feature set
by default, which means v8.0 without the CRC instructions, so U-Boot
hangs very early at the moment, without any output (the boot-wrapper or
TF-A printing the last visible lines).
Support for those instructions can be enabled on the model command line
by either:
-C cluster0.cpu0.enable_crc32=1 (for each core)
or by using a higher architecture revision by default:
-C cluster0.has_arm_v8-1=1 (for each cluster)
Of course any arch revision higher than v8.1 would work as well.
But for the sake of a smooth out-of-the-box experience, let's just
disable the usage of those instructions in the defconfig, to avoid
random hangs without any clues.
Reported-by: Ross Burton <ross.burton@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Marek Vasut <marex@denx.de>
This patch configures U-Boot SPL for DHCOR SoM to permit DFU upload of
SPL and subsequent u-boot.itb for recovery or commissioning purposes.
To start U-Boot on DHCOR based board, e.g. Avenger96, proceed as follows:
- Install dfu-util on the host PC (in debian this is package 'dfu-util')
- Power off the Avenger96 board.
- Connect both USB-serial console and USB-OTG microB ports to host PC.
- Switch Avenger96 to USB boot mode -- BOOT0..2 switches all set to 0.
- Power on the Avenger96 board.
- Verify using '$ dmesg' that a new device has been detected as follows:
New USB device found, idVendor=0483, idProduct=df11, bcdDevice= 2.00
New USB device strings: Mfr=1, Product=2, SerialNumber=3
Product: DFU in HS Mode @Device ID /0x500, @Revision ID /0x0000
Manufacturer: STMicroelectronics
- Upload U-Boot SPL:
$ dfu-util -a 1 -D u-boot-spl.stm32
- Upload U-Boot proper:
$ dfu-util -a 0 -D u-boot.itb
- At this point, SPL will wait for user to press "Ctrl-C" on serial
console. When ready to interact with U-Boot, press Ctrl-C to start
the bootloader.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This converts the following to Kconfig:
CONFIG_AT91_EFLASH
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Eugen Hristev <eugen.hristev@microchip.com>
Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS
and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries
to defconfigs.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Falcon mode is very useful in improving boot speed. A question that
Falcon mode asks is "Where do I look for the kernel". With MMC boot
media, the correct answer is CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR.
The scope of this patch is to move this to Kconfig.
It is possible for a system to support Falcon mode from NOR but not
MMC. In that case, mmc_load_image_raw_os() would not be used. To
address this, conditionally compile mmc_load_image_raw_os() when
SPL_FALCON_BOOT_MMCSD, instead of SPL_OS_BOOT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Move spl_start_uboot to its own guard in spl_mmc.c, rerun migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
After next branch was merged to v2022.01 release, U-Boot on A3720 started
printing "<debug_uart>" line on UART during booting. There is no need to
print this debug line by default, so disable it via config option
CONFIG_DEBUG_UART_ANNOUNCE in all config files for Armada 3720 boards.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
On of the MiniPCIe ports on Turris Omnia is also a mSATA port. Whether
it works in SATA or PCIe mode is determined by a strapping pin, which
value is read from the MCU.
We already determine which type of card is connected when configuring
SerDeses.
But until now we left both SATA and PCIe port 0 nodes in device tree
enabled, and so the SATA driver is probed in U-Boot / Linux even if we
know there is no mSATA card, and similarly PCIe driver tries to link on
port 0 even if we know there is mSATA card, not a PCIe card.
Fixup device tree blob to disable SATA node if mSATA card is not
present, and to disable PCIe port 0 node if mSATA card is present.
Do this for U-Boot's DT blob before relocation and also for kernel DT
blob before booting.
This ensures that software does not try to use SATA or PCIe HW when
corresponding PHY is not configured.
Signed-off-by: Pali Rohár <pali@kernel.org>
[ refactored and fixed some issues ]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The Khadas vim3 and vim3l defconfigs introduced with:
* f89b90d2d9 ("configs: add khadas-vim3{l}_android for AOSP support")
* 425f06f86e ("configs: prepare khadas-vim3{l}_ab_android for AOSP support")
were based on an outdated defconfig prior to the ede1f4f297 ("configs:
amlogic: Disable CONFIG_NET_RANDOM_ETHADDR when unnecessary") cleanup.
Disable CONFIG_NET_RANDOM_ETHADDR for the android configs as well to
stay consistent.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20220112084023.2858375-1-mkorpershoek@baylibre.com
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
- Let am335x_evm use the CPSW or PRUSS ethernet.
- Implement timer_get_boot_us in the omap timer driver
- gpmc bitflip, QSPI clock calculation on am437x, da8xx_gpio bugfixes
- Assorted K3 updates
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmHlNOccHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyL0JB/4+sKNWPMgOYvP2uLCC
euRGomhxJ5WmxJVDtJeBIRg0YKSkwnE8JwIN2qqGu15xJnNX9Ck5qnIMPbiZ/io9
ocW5Z/4C4rfJX/OzD6FtmbMNsvG/umVmZkjRU3ryRXKGyNVpVjLQ2EEECaJfk1WZ
Nd/J6/Jo8nafb1x4OeY+F6+xwZAuj7Mrun9SsDSyrIvmEqSnaQNioj+lStkauL51
NwQgBxZBQmbdCgF7Ooy6rYlXZBR6r/rgWB9n3RP8emDCwfCMul9HOMT432oKNbhW
bGrcMu9AWv/pgzXogxSzYbEdTAnoVEODtU1suCa8LV6KJPEG693gARnRm/KjvPHa
FfsK
=39IY
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.04-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2022.04 cycle:
This small feature set includes few changes for sama7g5 and sama7g5ek:
turn blue led on at boot, changes required for the Rev4 of the board,
better sync with the Linux DT with regards to the new DT nodes.
CONFIG_PHANDLE_CHECK_SEQ will allow different sequence number for nodes
that have the same name, but they are different.
In sama7g5ek case, there are multiple 'i2c@600' nodes which are child
nodes of different parent 'flexcom' nodes.
These are different i2c busses even if the node is the same, and have to be
differentiated.
Without this config, the sequence number 0 is reused for two i2c busses, and
this is something that we have to avoid:
Looking for 'i2c' at 4704, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
Found seq 0
i2c_post_bind: i2c@600, seq=0
Looking for 'i2c' at 6236, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
Found seq 0
i2c_post_bind: i2c@600, seq=0
After this patch:
Looking for 'i2c' at 4704, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
- i2c1, /ahb/apb/flexcom@e2818000/i2c@600
Found seq 1
Before the patch:
=> i2c bus
Bus 0: i2c@600
Bus 0: i2c@600 (active 0)
52: eeprom@52, offset len 1, flags 0
53: eeprom@53, offset len 1, flags 0
=>
After the patch:
=> i2c bus
Bus 0: i2c@600
Bus 1: i2c@600 (active 1)
52: eeprom@52, offset len 1, flags 0
53: eeprom@53, offset len 1, flags 0
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Memory layout in the comment is from Armada XP platform which uses load
address 0x40004030. DB-88f6720 is Armada 375 platform which uses same load
address as Armada 38x which is 0x40000030.
Currently SPL support for Armada 375 is unfinished and does not work. There
is missing Serdes initialization and DDR3 training code. So nobody noticed
that CONFIG_SPL_* options are not correct.
Fix at least CONFIG_SPL_TEXT_BASE constant and remove incorrect comments
about memory layout. So it is not misleading.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- Add MVEBU PCIe configs
- Also add SYS_THUMB_BUILD to keep u-boot image size within 512K
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The only user of board_pex_config() weak function is A385 controlcenterdc
board. It looks like that code in its board_pex_config() function needs to
be executed after PCIe link is up. Therefore put this code into
spl_board_init() function which is called after a38x serdes initialization,
and therefore it is after the serdes hws_pex_config() function finishes
(which is the state before this change).
With this change completely remove board_pex_config() function as it is not
used anymore.
Signed-off-by: Pali Rohár <pali@kernel.org>
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
-----BEGIN PGP SIGNATURE-----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=dLEg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
Since commit f7ac30b042, the pin muxing for mmc was removed from the
board file to be managed by DM_MMC which requires PINCTRL to work. It
made the change for sabrelite but nitrogen configs were forgotten.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Increase CONFIG_ENV_OFFSET to avoid the environment region to
overlap with U-Boot proper.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
After the conversion to DM the SD card shows up as 'mmc 2'
device.
Adjust the 'mmcdev' and the distro command 'func' accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Use binman to pack images.
Note that imx8mm_venice supports several boards via multiple DTB's thus
in the fit node we must use:
- fit,fdt-list = "of-list"
- fdt-SEQ
- config-SEQ
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The standard 1GB Nano was converted to binman, but the 2G version
was neglected. Convert it to binman as well.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Somewhere along the line, the board stopped being able to boot.
Rather than just fixing the issue, let's fix the issue and migrate
to binman to eliminate a warning when using custom imx tools for
generating the binary.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
To eliminate a warning when using custom imx tools for generating
a binary, use binman to generate flash.bin.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable support for USB and USB storage on the UDOO Neo.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The ethernet has a RMII not RGMII, also needs DM_MDIO and finally
initialise it later in the process as it's not needed that early on
and not everything is ready so it locks up the device.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes booting from the mSD card from both SPL and when
using it for the OS booting. It also cleans up a few mmc
booting bits that are no longer needed.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
meson64_android.h also relies on CMD_AB_SELECT so enable that as well.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211122152207.219023-5-mkorpershoek@baylibre.com
In AOSP, both VIM3 and VIM3L have 2 bootloader flavors,
depending on A/B enablement.
For example, for vim3l, the naming is:
- u-boot_kvim3l_noab.bin : legacy support
- u-boot_kvim3l_ab.bin : A/B support
Prepare a defconfig to support u-boot_kvim3_ab.bin and
u-boot_kvim3l_ab.bin.
This is identical to khadas-vim3{l}_ab_android but will be updated in
the next commit.
Also update partitioning tables for A/B support.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211122152207.219023-4-mkorpershoek@baylibre.com
On Meson GXL, GXM, AXG, G12A, G12B & SM1 SoCs, we can generate an unique
MAC address if none valid found in the eFuses storage.
Only the GXBB based boards doesn't have a fallback way to generate an
unique MAC address, so we rely on CONFIG_NET_RANDOM_ETHADDR to have
a valid one.
An exception is the Radxa Zero board who doesn't have Ethernet on board
so depends on an (or multiple) eventual USB adapters, so leaving the
CONFIG_NET_RANDOM_ETHADDR configs seems safer.
Suggested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211122110710.1038893-1-narmstrong@baylibre.com
DTBs are explicitly listed in the image source file for this board, and
this list already became outdated.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Move env var address values to #defines so they can be reused elsewhere.
Rename env var names to those recommended in the README and modify
addresses to allow more space for the kernel.
Fix issue where fdt is called with invalid arguments when booting
without a ramdisk.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYcsdCQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXCLhAJ9pLJE3SpQRzpm+Nu4EMbCDzZKr+wCfbxnAZ9LC
zS1XZ6u9Se4ysDb+PYs=
=Hf5j
-----END PGP SIGNATURE-----
Merge tag 'video-next-20211228' of https://source.denx.de/u-boot/custodians/u-boot-video into next
- various fixes to the sandbox display support
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
This converts the following to Kconfig:
CONFIG_JFFS2_DEV
CONFIG_JFFS2_LZO
CONFIG_JFFS2_NAND
CONFIG_JFFS2_PART_OFFSET
CONFIG_JFFS2_PART_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_88F5182
CONFIG_BOARD_IS_OPENRD_BASE
CONFIG_BOARD_IS_OPENRD_CLIENT
CONFIG_BOARD_IS_OPENRD_ULTIMATE
CONFIG_D2NET_V2
CONFIG_FEROCEON
CONFIG_FEROCEON_88FR131
CONFIG_INETSPACE_V2
CONFIG_KW88F6192
CONFIG_KW88F6281
CONFIG_KW88F6702
CONFIG_NET2BIG_V2
CONFIG_NETSPACE_LITE_V2
CONFIG_NETSPACE_MAX_V2
CONFIG_NETSPACE_MINI_V2
CONFIG_NETSPACE_V2
CONFIG_SHEEVA_88SV131
At this point mv-plug-common.h is now only an include of mv-common.h so
remove that indirection.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.
With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VID
CONFIG_VOL_MONITOR_INA220
CONFIG_VOL_MONITOR_IR36021_READ
CONFIG_VOL_MONITOR_IR36021_SET
CONFIG_VOL_MONITOR_LTC3882_READ
CONFIG_VOL_MONITOR_LTC3882_SET
To finish this migration, we first need to introduce CONFIG_SPL_VID as
some platforms only use this code in full U-Boot while others use it in
SPL as well. To make the Kconfig logic clearer, guard all of the
sub-options with a if VID || SPL_VID check. Finally, add Kconfig
options for the remaining related options that did not previously have
one.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_IMMR
We do this by consolidating the SYS_IMMR options we have and providing
defaults.
We also, in the few places where M68K was also sharing code with these
platforms, define it within the file to CONFIG_SYS_MBAR to match usage.
This should be cleaned up longer term.
Signed-off-by: Tom Rini <trini@konsulko.com>
Because of how these symbols work, and the remaining board config.h file
uses, we need to do these at the same time. In some cases we just get
to move rather directly to the defconfigs. A few cases require manual
intervention.
For the case of the eb_cpu5282 we need to select HW_WATCHDOG for the
target, given how it's implemented.
For the cases of m53menlo, dh_imx6, display5, and display5_factory we
disable SPL watchdog support as the particular combination of options
they want would require either more symbols or enabling SPL_DM.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT
In order to do this conversion, expose this option to the user and
use "save" not "safe" in the text.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SUPPORT_EMMC_RPMB
This fixes a few platforms where the option was not taking effect as
intended.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
As part of this, we use Kconfig to provide the defaults now that were
done in include/spi_flash.h. We also in some cases change from using
CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in
use anyhow as ENV was not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is a "hex" prompt but the default value was given as an int.
Switch the default to hex (0x0) and remove the defconfigs that were
using the default, but as hex before.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable this for boards with a display, unless they are using the SPLASH
feature.
This shows a U-Boot logo on boards with a display, which seems like a
useful thing.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_VIDEO_LOGO
Note that this option depends on CONFIG_DM_VIDEO now, since cfb_console is
deprecated. The only relevant code is now in splash.c
Drop the check for DM_VIDEO in that file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this uses RGB555 format for blitting to a display. Sandbox uses
565 and that seems to be more normal for BMP as well. Update the code
accordingly and add a test.
Note that this likely breaks the theadorable board so we may need to
discuss supporting both formats.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable efuse support for reading the cpuid#, serial# and generate a
board unique mac address
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
10.1" OF is a capacitive touch 10.1" Open Frame panel solutions.
PX30.Core needs to mount on top of C.TOUCH 2.0 carrier with pluged
10.1" OF for creating complete PX30.Core C.TOUCH 2.0 10.1" Open Frame.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the px30 devicetree files from linux-next tree.
commit <14ce8069f48b> ("lib/stackdepot: allow optional init and
stack_table allocation by kvmalloc() - fixup3")
Note, this path even sync rk3326 files as it depends on px30.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable SPL support in Kconfig and add some related option in
rk3568_common.h
Signed-off-by: Nico Cheng <nico.cheng@rock-chips.com>
Signed-off-by: Jason Zhu <jason.zhu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use this new Kconfig instead of OF_BOARD, so we know for sure which boards
obtain their devicetree from a prior stage. Leave sandbox alone since it
does not. Also don't touch xilinx_versal_virt since it does not have a
specific TARGET Kconfig.
This option implies OF_BOARD for now, but with future work standard
passage may be used instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add rpi_4_32b and rpi_arm64 to the list of boards converted]
Signed-off-by: Tom Rini <trini@konsulko.com>
This should not be a separate option from OF_SEPARATE. It is a run-time
option to override the devicetree, even if present.
Move the option out of the choice.
Disable BINMAN_FDT for a few boards which don't actually use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses QEMU virt which creates its own devicetree.
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an empty devicetree file for these boards. It seems to be possible to
obtain a real one from another bootloader called 'bolt' but I will leave
this to the maintainer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an empty file to prevent build errors when building with
CONFIG_OF_SEPARATE enabled.
Unfortunately there are no build instructions in the U-Boot tree to enable
a real file to be created.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
The real devicetree is created by the Xen project on-the-fly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sync these file, obtained from Linux v5.15.
Add a note for the maintainer, and SPDX lines where they are missing.
The added lines are:
SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
Note, this matches the text in those files, but is not the same as the
GPL-2.0 of some files.
[1] https://releases.linaro.org/android/reference-lcr/juno/7.1-17.05/
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Sync these files, obtained from Linux v5.15.
This adds a devicetree file for rpi_4 which was not there before.
Testing shows no change so far as I can see:
- boots to U-Boot prompt on rpi0, rpi2
- boots to distro on rpi3
- boots to distro on rpi4
I am assuming that syncing with Linux is safe, but the maintainer should
know for sure.
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses QEMU virt which creates its own devicetree.
Copy the existing empty version of this file, so splitting the existing
qemu-virt into two, since anyone actually trying to use this will need a
different devicetree for 32- and 64-bit machines.
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canaonical.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses QEMU virt which creates its own devicetree.
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canaonical.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses QEMU virt which creates its own devicetree.
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canaonical.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Move to the DM I2C version, so that this board will not get dropped from
mainline.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmG8PNIcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyN4NCACbdi5EFjoNkGhCWLIX
SobXNcBGaL9Zpr5qZq77uFqFeFPeiAClk9X+TcSHhBTSWPugzNCdXEdENEGdiiOR
Yxe/QvBL7ZsKkhGBw5W8sb81NBPlpnVY7DWufjYvWq7S3C3bIDahQpCeWHKXDO0H
ZzIX1413kfHRKsAIT+IbufmC1dcWY8SWQEArSkL2KhTQyHnLVGAaholgEGXoKMoC
0ACXO+uhqaAY0/1eWvvYjcfotlz881ROajSRITh+Gu0UuHyRr2Fvj7jZvF5E4Q4f
Cu8iciDsimYSDGLZsOJjPIDTfsx9jbA8IcYIAMxOLW8OYbIL6QAUKsJ2LLKao1q5
SYXP
=YXsB
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.04 cycle:
This feature set includes : support for the new QSPI hardware on
sama7g5, small fixes on sam9x60 and sama7g5, some additions of commands
and PIO controller on sam9x60/sam9x60ek.
Enable KSZ9x01 PHY driver in DHCOR common configuration, since the
AV96 board has this PHY populated on the PCB.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The resync of the device trees from Linux 5.16-rc3 caused aliases
to appear on the MMC devices which changed the numbering.
This broke the reading/writing of the environmental variables,
so update the defconfig accordingly.
Signed-off-by: Adam Ford <aford173@gmail.com>
This is not used by sandbox since it uses driver model for the timer.
Drop it.
Also update the tools_only build to avoid build errors, since it does
actually build U-Boot too. Enable DM so we can use CONFIG_TIMER,
disable EFI_LOADER to avoid an error about board_quiesce_devices() and
disable NET to avoid having to define CONFIG_AVB_BUF_ADDR
Signed-off-by: Simon Glass <sjg@chromium.org>
Configure SPI flash devices into SPL. Add SPI boot option to spl.c.
Document how to format flash for booting.
Signed-off-by: Thomas Skibo <thomas-git@skibo.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This patch updates Microchip MPFS Icicle Kit support. For now,
add Microchip I2C driver, set environment variables for
mac addresses and default build for SBI_V02.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This converts the following to Kconfig:
CONFIG_SYS_BR0_PRELIM
CONFIG_SYS_OR1_PRELIM
CONFIG_SYS_BR1_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR2_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR3_PRELIM
CONFIG_SYS_OR3_PRELIM
CONFIG_SYS_BR4_PRELIM
CONFIG_SYS_OR4_PRELIM
CONFIG_SYS_BR5_PRELIM
CONFIG_SYS_OR5_PRELIM
CONFIG_SYS_BR6_PRELIM
CONFIG_SYS_OR6_PRELIM
CONFIG_SYS_BR7_PRELIM
CONFIG_SYS_OR7_PRELIM
This also introduces CONFIG_SYS_BR0_PRELIM_BOOL as not all platforms
that can set these values do so. Add the relevant SYS_BRx_PRELIM_BOOL
to platforms that had not been previously migrated.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND
Signed-off-by: Tom Rini <trini@konsulko.com>
The IPCC mailbox is only used for communication with M4 firmware but
it is not used in the stm32 remoteproc driver; it was planed but the
support of this mailbox in remoteproc for STM32MP15x is dropped.
So the associated drivers and config CONFIG_STM32_IPCC can be
deactivated to reduce the U-Boot size; the CONFIG_DM_MAILBOX can be
also deactivated as the mailbox UCLASS is no more used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable an existing simple framebuffer node in the Linux kernel device
tree and the add the associated reserved memory node to preserved the
resources (clock, memory) used by the stm32 video driver to display
the splashscreen = background in exlinux.conf file.
These resources will be released by the Linux driver only when the
associated driver is ready to avoid transition issues during the Linux
kernel initialization between U-Boot splash screen and the final display.
See Linux documentation for details:
Documentation/devicetree/bindings/display/simple-framebuffer.yaml
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This converts the following to Kconfig:
CONFIG_LCD_DT_SIMPLEFB
This patch also renames this config to CONFIG_FDT_SIMPLEFB as the code in
common/lcd_simplefb.c support CONFIG_LCD and CONFIG_VIDEO.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Enable KSZ9x01 PHY driver in DHCOR common configuration, since the
AV96 board has this PHY populated on the PCB.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
With TPM emulation enabled in u-boot-test-hooks we should also provide the
tpm2 command used for the test/py/tests/test_tpm2.py test.
One of the Python TPMv2 tests expects sandbox specific values. So disable
it on other platforms.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
At present the hexdump tests are disabled in sandbox_flattree. This is
good, because they do not pass. Enable the required Kconfig so that they
will, when enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Deactivate the SCMI agent mailbox which is not used on STM32MP15
platforms.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Some boards need to change the tx/rx delay config in order for
gigabit Ethernet to work.
In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), Realtek documented the bits for overriding the delays
from the hardware straps.
Copy the logic from linux, so the delay config is set from the PHY's
interface type (the phy-mode property in the device tree).
This removes the need for a one-off workaround for the Pine A64+ board.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Don't fail when booting a board with an empty EEPROM for MAC addresses.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The sja1105 is a 5-port switch that uses a DM_DSA driver. Its 5th (CPU)
port is connected internally to the eth2 port of the LS1021A SoC.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add dm command for driver model low level access and
gpio command for query and control gpio pins.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
AST2600 leverages the FIT hash/signature verification to fulfill
secure boot trust chain. To improve the performance and save SW
code size for those crypto operations, the two HW crypto engine,
HACE and ACRY, are enabled.
However, both of the engines can only access to data stored in
DRAM space. Therefore, we need to move the FIT image into DRAM
before the booting.
This patch update the CONFIG_BOOTCOMMAND to execute the pre-defined
ENV variable which consists of FIT image copy to memory and booting.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Enable SPL FIT image load and verification support.
The HW accelerated SHA is also available with the
newly added support of the HACE HW hash engine.
The SPL thumb build is also enabled to keep the binary
less than 64KB to fit into the Aspeed secure boot design.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Enable this to permit early debugging. Due to the way qmeu works, the
input clock can be zero and things still work.
Signed-off-by: Simon Glass <sjg@chromium.org>
A few boards enable CONFIG_DEBUG_UART_BOARD_INIT but do not define the
required init function. Fix this by disabling the debug UART.
With snow the debug UART is enabled but the driver CONFIG is not. Fix this
too.
Signed-off-by: Simon Glass <sjg@chromium.org>
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYZPDrwAKCRDKSWXLKUoM
IS9GAJ93T/uprhLcKWMb+284YMb2caWgOACfZ02nTlzvZKNNXVretJgZaHXqj1M=
=cwTL
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.01-rc3
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_SPI_FLASH
CONFIG_ENV_IS_NOWHERE
CONFIG_ENV_OFFSET
CONFIG_ENV_OVERWRITE
CONFIG_ENV_SECT_SIZE
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Signed-off-by: Tom Rini <trini@konsulko.com>
This got lost while fixing up the condition in
board/siemens/iot2050/board.c
Fixes: b55881dd ("bootstage: Add SPL support")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- device-tree sync-up with Linux for ls1028a
- fixes/update in fsl-ddr driver, fsl-validate, lx2162a, fsl-mc,
spintable code, configs, qspi node, pci
- enable EFI_SET_TIME support in sl28
- powerpc: Drop -mstring
A previous commit is adding an MMIO TPMv2 driver. Include in the default
qemu arm configs, since we plan on using them on EFI testing
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
-----BEGIN PGP SIGNATURE-----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=lqEG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211110' of https://source.denx.de/u-boot/custodians/u-boot-stm
- DHSOM update:
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
